NCR5380.c 69.8 KB
Newer Older
1
// SPDX-License-Identifier: GPL-2.0
2
/*
L
Linus Torvalds 已提交
3
 * NCR 5380 generic driver routines.  These should make it *trivial*
4 5
 * to implement 5380 SCSI drivers under Linux with a non-trantor
 * architecture.
L
Linus Torvalds 已提交
6
 *
7
 * Note that these routines also work with NR53c400 family chips.
L
Linus Torvalds 已提交
8 9
 *
 * Copyright 1993, Drew Eckhardt
10 11 12 13
 * Visionary Computing
 * (Unix and Linux consulting and custom programming)
 * drew@colorado.edu
 * +1 (303) 666-5836
L
Linus Torvalds 已提交
14
 *
15
 * For more information, please consult
L
Linus Torvalds 已提交
16 17 18 19 20 21 22 23 24 25 26 27 28
 *
 * NCR 5380 Family
 * SCSI Protocol Controller
 * Databook
 *
 * NCR Microelectronics
 * 1635 Aeroplaza Drive
 * Colorado Springs, CO 80916
 * 1+ (719) 578-3400
 * 1+ (800) 334-5454
 */

/*
F
Finn Thain 已提交
29 30
 * With contributions from Ray Van Tassle, Ingmar Baumgart,
 * Ronald van Cuijlenborg, Alan Cox and others.
L
Linus Torvalds 已提交
31 32
 */

33 34
/* Ported to Atari by Roman Hodek and others. */

35 36
/* Adapted for the Sun 3 by Sam Creasey. */

L
Linus Torvalds 已提交
37 38 39
/*
 * Design
 *
40
 * This is a generic 5380 driver.  To use it on a different platform,
L
Linus Torvalds 已提交
41
 * one simply writes appropriate system specific macros (ie, data
42
 * transfer - some PC's will use the I/O bus, 68K's must use
L
Linus Torvalds 已提交
43 44
 * memory mapped) and drops this file in their 'C' wrapper.
 *
45
 * As far as command queueing, two queues are maintained for
L
Linus Torvalds 已提交
46
 * each 5380 in the system - commands that haven't been issued yet,
47 48 49 50 51
 * and commands that are currently executing.  This means that an
 * unlimited number of commands may be queued, letting
 * more commands propagate from the higher driver levels giving higher
 * throughput.  Note that both I_T_L and I_T_L_Q nexuses are supported,
 * allowing multiple commands to propagate all the way to a SCSI-II device
L
Linus Torvalds 已提交
52 53 54
 * while a command is already executing.
 *
 *
55
 * Issues specific to the NCR5380 :
L
Linus Torvalds 已提交
56
 *
57 58 59 60
 * When used in a PIO or pseudo-dma mode, the NCR5380 is a braindead
 * piece of hardware that requires you to sit in a loop polling for
 * the REQ signal as long as you are connected.  Some devices are
 * brain dead (ie, many TEXEL CD ROM drives) and won't disconnect
61
 * while doing long seek operations. [...] These
L
Linus Torvalds 已提交
62 63 64 65 66 67 68 69 70
 * broken devices are the exception rather than the rule and I'd rather
 * spend my time optimizing for the normal case.
 *
 * Architecture :
 *
 * At the heart of the design is a coroutine, NCR5380_main,
 * which is started from a workqueue for each NCR5380 host in the
 * system.  It attempts to establish I_T_L or I_T_L_Q nexuses by
 * removing the commands from the issue queue and calling
71
 * NCR5380_select() if a nexus is not established.
L
Linus Torvalds 已提交
72 73 74 75 76
 *
 * Once a nexus is established, the NCR5380_information_transfer()
 * phase goes through the various phases as instructed by the target.
 * if the target goes into MSG IN and sends a DISCONNECT message,
 * the command structure is placed into the per instance disconnected
77
 * queue, and NCR5380_main tries to find more work.  If the target is
L
Linus Torvalds 已提交
78 79 80 81 82 83
 * idle for too long, the system will try to sleep.
 *
 * If a command has disconnected, eventually an interrupt will trigger,
 * calling NCR5380_intr()  which will in turn call NCR5380_reselect
 * to reestablish a nexus.  This will run main if necessary.
 *
84
 * On command termination, the done function will be called as
L
Linus Torvalds 已提交
85 86
 * appropriate.
 *
87
 * SCSI pointers are maintained in the SCp field of SCSI command
L
Linus Torvalds 已提交
88 89 90 91 92 93 94 95 96
 * structures, being initialized after the command is connected
 * in NCR5380_select, and set as appropriate in NCR5380_information_transfer.
 * Note that in violation of the standard, an implicit SAVE POINTERS operation
 * is done, since some BROKEN disks fail to issue an explicit SAVE POINTERS.
 */

/*
 * Using this file :
 * This file a skeleton Linux SCSI driver for the NCR 5380 series
97
 * of chips.  To use it, you write an architecture specific functions
L
Linus Torvalds 已提交
98 99 100
 * and macros and include this file in your driver.
 *
 * These macros MUST be defined :
101
 *
L
Linus Torvalds 已提交
102 103
 * NCR5380_read(register)  - read from the specified register
 *
104
 * NCR5380_write(register, value) - write to the specific register
L
Linus Torvalds 已提交
105
 *
106
 * NCR5380_implementation_fields  - additional fields needed for this
107
 * specific implementation of the NCR5380
L
Linus Torvalds 已提交
108 109 110
 *
 * Either real DMA *or* pseudo DMA may be implemented
 *
111 112 113 114
 * NCR5380_dma_xfer_len   - determine size of DMA/PDMA transfer
 * NCR5380_dma_send_setup - execute DMA/PDMA from memory to 5380
 * NCR5380_dma_recv_setup - execute DMA/PDMA from 5380 to memory
 * NCR5380_dma_residual   - residual byte count
L
Linus Torvalds 已提交
115 116
 *
 * The generic driver is initialized by calling NCR5380_init(instance),
117
 * after setting the appropriate host specific fields and ID.
L
Linus Torvalds 已提交
118 119
 */

120 121 122 123
#ifndef NCR5380_io_delay
#define NCR5380_io_delay(x)
#endif

124 125 126 127 128 129 130 131
#ifndef NCR5380_acquire_dma_irq
#define NCR5380_acquire_dma_irq(x)	(1)
#endif

#ifndef NCR5380_release_dma_irq
#define NCR5380_release_dma_irq(x)
#endif

132 133
static int do_abort(struct Scsi_Host *);
static void do_reset(struct Scsi_Host *);
L
Linus Torvalds 已提交
134

F
Finn Thain 已提交
135
/**
136
 * initialize_SCp - init the scsi pointer field
137
 * @cmd: command block to set up
L
Linus Torvalds 已提交
138
 *
139
 * Set up the internal fields in the SCSI command.
L
Linus Torvalds 已提交
140 141
 */

F
Finn Thain 已提交
142
static inline void initialize_SCp(struct scsi_cmnd *cmd)
L
Linus Torvalds 已提交
143
{
144 145
	/*
	 * Initialize the Scsi Pointer field so that all of the commands in the
L
Linus Torvalds 已提交
146 147 148
	 * various queues are valid.
	 */

149 150 151
	if (scsi_bufflen(cmd)) {
		cmd->SCp.buffer = scsi_sglist(cmd);
		cmd->SCp.buffers_residual = scsi_sg_count(cmd) - 1;
J
Jens Axboe 已提交
152
		cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
L
Linus Torvalds 已提交
153 154 155 156
		cmd->SCp.this_residual = cmd->SCp.buffer->length;
	} else {
		cmd->SCp.buffer = NULL;
		cmd->SCp.buffers_residual = 0;
157 158
		cmd->SCp.ptr = NULL;
		cmd->SCp.this_residual = 0;
L
Linus Torvalds 已提交
159
	}
F
Finn Thain 已提交
160 161 162

	cmd->SCp.Status = 0;
	cmd->SCp.Message = 0;
L
Linus Torvalds 已提交
163 164 165
}

/**
166
 * NCR5380_poll_politely2 - wait for two chip register values
167
 * @hostdata: host private data
168 169 170 171 172 173
 * @reg1: 5380 register to poll
 * @bit1: Bitmask to check
 * @val1: Expected value
 * @reg2: Second 5380 register to poll
 * @bit2: Second bitmask to check
 * @val2: Second expected value
174 175 176 177 178 179 180
 * @wait: Time-out in jiffies
 *
 * Polls the chip in a reasonably efficient manner waiting for an
 * event to occur. After a short quick poll we begin to yield the CPU
 * (if possible). In irq contexts the time-out is arbitrarily limited.
 * Callers may hold locks as long as they are held in irq mode.
 *
181
 * Returns 0 if either or both event(s) occurred otherwise -ETIMEDOUT.
L
Linus Torvalds 已提交
182
 */
183

184
static int NCR5380_poll_politely2(struct NCR5380_hostdata *hostdata,
185 186 187
                                  unsigned int reg1, u8 bit1, u8 val1,
                                  unsigned int reg2, u8 bit2, u8 val2,
                                  unsigned long wait)
L
Linus Torvalds 已提交
188
{
189
	unsigned long n = hostdata->poll_loops;
190 191 192
	unsigned long deadline = jiffies + wait;

	do {
193 194 195
		if ((NCR5380_read(reg1) & bit1) == val1)
			return 0;
		if ((NCR5380_read(reg2) & bit2) == val2)
L
Linus Torvalds 已提交
196 197
			return 0;
		cpu_relax();
198 199 200 201 202 203 204 205
	} while (n--);

	if (irqs_disabled() || in_interrupt())
		return -ETIMEDOUT;

	/* Repeatedly sleep for 1 ms until deadline */
	while (time_is_after_jiffies(deadline)) {
		schedule_timeout_uninterruptible(1);
206 207 208
		if ((NCR5380_read(reg1) & bit1) == val1)
			return 0;
		if ((NCR5380_read(reg2) & bit2) == val2)
L
Linus Torvalds 已提交
209 210
			return 0;
	}
211

L
Linus Torvalds 已提交
212 213 214
	return -ETIMEDOUT;
}

215
#if NDEBUG
L
Linus Torvalds 已提交
216 217 218
static struct {
	unsigned char mask;
	const char *name;
219 220 221 222 223 224 225 226 227
} signals[] = {
	{SR_DBP, "PARITY"},
	{SR_RST, "RST"},
	{SR_BSY, "BSY"},
	{SR_REQ, "REQ"},
	{SR_MSG, "MSG"},
	{SR_CD, "CD"},
	{SR_IO, "IO"},
	{SR_SEL, "SEL"},
L
Linus Torvalds 已提交
228
	{0, NULL}
229
},
L
Linus Torvalds 已提交
230
basrs[] = {
231 232 233 234 235 236
	{BASR_END_DMA_TRANSFER, "END OF DMA"},
	{BASR_DRQ, "DRQ"},
	{BASR_PARITY_ERROR, "PARITY ERROR"},
	{BASR_IRQ, "IRQ"},
	{BASR_PHASE_MATCH, "PHASE MATCH"},
	{BASR_BUSY_ERROR, "BUSY ERROR"},
237 238
	{BASR_ATN, "ATN"},
	{BASR_ACK, "ACK"},
L
Linus Torvalds 已提交
239
	{0, NULL}
240 241 242
},
icrs[] = {
	{ICR_ASSERT_RST, "ASSERT RST"},
243 244
	{ICR_ARBITRATION_PROGRESS, "ARB. IN PROGRESS"},
	{ICR_ARBITRATION_LOST, "LOST ARB."},
245 246 247 248 249
	{ICR_ASSERT_ACK, "ASSERT ACK"},
	{ICR_ASSERT_BSY, "ASSERT BSY"},
	{ICR_ASSERT_SEL, "ASSERT SEL"},
	{ICR_ASSERT_ATN, "ASSERT ATN"},
	{ICR_ASSERT_DATA, "ASSERT DATA"},
L
Linus Torvalds 已提交
250
	{0, NULL}
251 252
},
mrs[] = {
253 254 255 256 257 258 259 260
	{MR_BLOCK_DMA_MODE, "BLOCK DMA MODE"},
	{MR_TARGET, "TARGET"},
	{MR_ENABLE_PAR_CHECK, "PARITY CHECK"},
	{MR_ENABLE_PAR_INTR, "PARITY INTR"},
	{MR_ENABLE_EOP_INTR, "EOP INTR"},
	{MR_MONITOR_BSY, "MONITOR BSY"},
	{MR_DMA_MODE, "DMA MODE"},
	{MR_ARBITRATE, "ARBITRATE"},
L
Linus Torvalds 已提交
261 262 263 264
	{0, NULL}
};

/**
265 266
 * NCR5380_print - print scsi bus signals
 * @instance: adapter state to dump
L
Linus Torvalds 已提交
267
 *
268
 * Print the SCSI bus signals for debugging purposes
L
Linus Torvalds 已提交
269 270 271 272
 */

static void NCR5380_print(struct Scsi_Host *instance)
{
273
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
274 275 276 277 278 279 280 281
	unsigned char status, data, basr, mr, icr, i;

	data = NCR5380_read(CURRENT_SCSI_DATA_REG);
	status = NCR5380_read(STATUS_REG);
	mr = NCR5380_read(MODE_REG);
	icr = NCR5380_read(INITIATOR_COMMAND_REG);
	basr = NCR5380_read(BUS_AND_STATUS_REG);

282
	printk(KERN_DEBUG "SR =   0x%02x : ", status);
L
Linus Torvalds 已提交
283 284
	for (i = 0; signals[i].mask; ++i)
		if (status & signals[i].mask)
285 286
			printk(KERN_CONT "%s, ", signals[i].name);
	printk(KERN_CONT "\nBASR = 0x%02x : ", basr);
L
Linus Torvalds 已提交
287 288
	for (i = 0; basrs[i].mask; ++i)
		if (basr & basrs[i].mask)
289 290
			printk(KERN_CONT "%s, ", basrs[i].name);
	printk(KERN_CONT "\nICR =  0x%02x : ", icr);
L
Linus Torvalds 已提交
291 292
	for (i = 0; icrs[i].mask; ++i)
		if (icr & icrs[i].mask)
293 294
			printk(KERN_CONT "%s, ", icrs[i].name);
	printk(KERN_CONT "\nMR =   0x%02x : ", mr);
L
Linus Torvalds 已提交
295 296
	for (i = 0; mrs[i].mask; ++i)
		if (mr & mrs[i].mask)
297 298
			printk(KERN_CONT "%s, ", mrs[i].name);
	printk(KERN_CONT "\n");
L
Linus Torvalds 已提交
299 300
}

301 302 303 304 305 306 307 308 309 310 311 312
static struct {
	unsigned char value;
	const char *name;
} phases[] = {
	{PHASE_DATAOUT, "DATAOUT"},
	{PHASE_DATAIN, "DATAIN"},
	{PHASE_CMDOUT, "CMDOUT"},
	{PHASE_STATIN, "STATIN"},
	{PHASE_MSGOUT, "MSGOUT"},
	{PHASE_MSGIN, "MSGIN"},
	{PHASE_UNKNOWN, "UNKNOWN"}
};
L
Linus Torvalds 已提交
313

F
Finn Thain 已提交
314
/**
315
 * NCR5380_print_phase - show SCSI phase
316
 * @instance: adapter to dump
L
Linus Torvalds 已提交
317
 *
318
 * Print the current SCSI phase for debugging purposes
L
Linus Torvalds 已提交
319 320 321 322
 */

static void NCR5380_print_phase(struct Scsi_Host *instance)
{
323
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
324 325 326 327 328
	unsigned char status;
	int i;

	status = NCR5380_read(STATUS_REG);
	if (!(status & SR_REQ))
329
		shost_printk(KERN_DEBUG, instance, "REQ not asserted, phase unknown.\n");
L
Linus Torvalds 已提交
330
	else {
331 332 333
		for (i = 0; (phases[i].value != PHASE_UNKNOWN) &&
		     (phases[i].value != (status & PHASE_MASK)); ++i)
			;
334
		shost_printk(KERN_DEBUG, instance, "phase %s\n", phases[i].name);
L
Linus Torvalds 已提交
335 336 337 338 339
	}
}
#endif

/**
340
 * NCR5380_info - report driver and host information
341
 * @instance: relevant scsi host instance
L
Linus Torvalds 已提交
342
 *
343
 * For use as the host template info() handler.
L
Linus Torvalds 已提交
344 345
 */

F
Finn Thain 已提交
346
static const char *NCR5380_info(struct Scsi_Host *instance)
L
Linus Torvalds 已提交
347
{
F
Finn Thain 已提交
348 349 350 351 352
	struct NCR5380_hostdata *hostdata = shost_priv(instance);

	return hostdata->info;
}

L
Linus Torvalds 已提交
353
/**
354
 * NCR5380_init - initialise an NCR5380
355 356
 * @instance: adapter to configure
 * @flags: control flags
L
Linus Torvalds 已提交
357
 *
358 359
 * Initializes *instance and corresponding 5380 chip,
 * with flags OR'd into the initial flags value.
L
Linus Torvalds 已提交
360
 *
361
 * Notes : I assume that the host, hostno, and id bits have been
362
 * set correctly. I don't care about the irq and other fields.
L
Linus Torvalds 已提交
363
 *
364
 * Returns 0 for success
L
Linus Torvalds 已提交
365 366
 */

367
static int NCR5380_init(struct Scsi_Host *instance, int flags)
L
Linus Torvalds 已提交
368
{
F
Finn Thain 已提交
369
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
370
	int i;
371
	unsigned long deadline;
372
	unsigned long accesses_per_ms;
L
Linus Torvalds 已提交
373

F
Finn Thain 已提交
374 375
	instance->max_lun = 7;

376
	hostdata->host = instance;
L
Linus Torvalds 已提交
377
	hostdata->id_mask = 1 << instance->this_id;
378
	hostdata->id_higher_mask = 0;
L
Linus Torvalds 已提交
379 380 381 382 383
	for (i = hostdata->id_mask; i <= 0x80; i <<= 1)
		if (i > hostdata->id_mask)
			hostdata->id_higher_mask |= i;
	for (i = 0; i < 8; ++i)
		hostdata->busy[i] = 0;
384 385
	hostdata->dma_len = 0;

386
	spin_lock_init(&hostdata->lock);
L
Linus Torvalds 已提交
387
	hostdata->connected = NULL;
F
Finn Thain 已提交
388 389
	hostdata->sensing = NULL;
	INIT_LIST_HEAD(&hostdata->autosense);
390 391 392
	INIT_LIST_HEAD(&hostdata->unissued);
	INIT_LIST_HEAD(&hostdata->disconnected);

393
	hostdata->flags = flags;
394

395
	INIT_WORK(&hostdata->main_task, NCR5380_main);
396 397 398 399 400 401
	hostdata->work_q = alloc_workqueue("ncr5380_%d",
	                        WQ_UNBOUND | WQ_MEM_RECLAIM,
	                        1, instance->host_no);
	if (!hostdata->work_q)
		return -ENOMEM;

402 403 404 405 406 407 408 409
	snprintf(hostdata->info, sizeof(hostdata->info),
		"%s, irq %d, io_port 0x%lx, base 0x%lx, can_queue %d, cmd_per_lun %d, sg_tablesize %d, this_id %d, flags { %s%s%s}",
		instance->hostt->name, instance->irq, hostdata->io_port,
		hostdata->base, instance->can_queue, instance->cmd_per_lun,
		instance->sg_tablesize, instance->this_id,
		hostdata->flags & FLAG_DMA_FIXUP     ? "DMA_FIXUP "     : "",
		hostdata->flags & FLAG_NO_PSEUDO_DMA ? "NO_PSEUDO_DMA " : "",
		hostdata->flags & FLAG_TOSHIBA_DELAY ? "TOSHIBA_DELAY " : "");
F
Finn Thain 已提交
410

L
Linus Torvalds 已提交
411 412 413 414
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
	NCR5380_write(MODE_REG, MR_BASE);
	NCR5380_write(TARGET_COMMAND_REG, 0);
	NCR5380_write(SELECT_ENABLE_REG, 0);
415 416 417 418 419 420 421 422 423 424 425 426 427

	/* Calibrate register polling loop */
	i = 0;
	deadline = jiffies + 1;
	do {
		cpu_relax();
	} while (time_is_after_jiffies(deadline));
	deadline += msecs_to_jiffies(256);
	do {
		NCR5380_read(STATUS_REG);
		++i;
		cpu_relax();
	} while (time_is_after_jiffies(deadline));
428 429
	accesses_per_ms = i / 256;
	hostdata->poll_loops = NCR5380_REG_POLL_TIME * accesses_per_ms / 2;
430

431 432
	return 0;
}
L
Linus Torvalds 已提交
433

434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449
/**
 * NCR5380_maybe_reset_bus - Detect and correct bus wedge problems.
 * @instance: adapter to check
 *
 * If the system crashed, it may have crashed with a connected target and
 * the SCSI bus busy. Check for BUS FREE phase. If not, try to abort the
 * currently established nexus, which we know nothing about. Failing that
 * do a bus reset.
 *
 * Note that a bus reset will cause the chip to assert IRQ.
 *
 * Returns 0 if successful, otherwise -ENXIO.
 */

static int NCR5380_maybe_reset_bus(struct Scsi_Host *instance)
{
450
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
451
	int pass;
L
Linus Torvalds 已提交
452 453 454 455 456 457

	for (pass = 1; (NCR5380_read(STATUS_REG) & SR_BSY) && pass <= 6; ++pass) {
		switch (pass) {
		case 1:
		case 3:
		case 5:
458
			shost_printk(KERN_ERR, instance, "SCSI bus busy, waiting up to five seconds\n");
459
			NCR5380_poll_politely(hostdata,
460
			                      STATUS_REG, SR_BSY, 0, 5 * HZ);
L
Linus Torvalds 已提交
461 462
			break;
		case 2:
463
			shost_printk(KERN_ERR, instance, "bus busy, attempting abort\n");
L
Linus Torvalds 已提交
464 465 466
			do_abort(instance);
			break;
		case 4:
467
			shost_printk(KERN_ERR, instance, "bus busy, attempting reset\n");
L
Linus Torvalds 已提交
468
			do_reset(instance);
469 470 471 472 473 474 475 476
			/* Wait after a reset; the SCSI standard calls for
			 * 250ms, we wait 500ms to be on the safe side.
			 * But some Toshiba CD-ROMs need ten times that.
			 */
			if (hostdata->flags & FLAG_TOSHIBA_DELAY)
				msleep(2500);
			else
				msleep(500);
L
Linus Torvalds 已提交
477 478
			break;
		case 6:
479
			shost_printk(KERN_ERR, instance, "bus locked solid\n");
L
Linus Torvalds 已提交
480 481 482 483 484 485 486
			return -ENXIO;
		}
	}
	return 0;
}

/**
487
 * NCR5380_exit - remove an NCR5380
488
 * @instance: adapter to remove
489 490
 *
 * Assumes that no more work can be queued (e.g. by NCR5380_intr).
L
Linus Torvalds 已提交
491 492
 */

493
static void NCR5380_exit(struct Scsi_Host *instance)
L
Linus Torvalds 已提交
494
{
F
Finn Thain 已提交
495
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
496

497
	cancel_work_sync(&hostdata->main_task);
498
	destroy_workqueue(hostdata->work_q);
L
Linus Torvalds 已提交
499 500
}

501 502 503 504 505 506 507 508 509 510 511 512 513
/**
 * complete_cmd - finish processing a command and return it to the SCSI ML
 * @instance: the host instance
 * @cmd: command to complete
 */

static void complete_cmd(struct Scsi_Host *instance,
                         struct scsi_cmnd *cmd)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);

	dsprintk(NDEBUG_QUEUES, instance, "complete_cmd: cmd %p\n", cmd);

F
Finn Thain 已提交
514 515
	if (hostdata->sensing == cmd) {
		/* Autosense processing ends here */
516
		if (status_byte(cmd->result) != GOOD) {
F
Finn Thain 已提交
517
			scsi_eh_restore_cmnd(cmd, &hostdata->ses);
518
		} else {
F
Finn Thain 已提交
519
			scsi_eh_restore_cmnd(cmd, &hostdata->ses);
520 521
			set_driver_byte(cmd, DRIVER_SENSE);
		}
F
Finn Thain 已提交
522 523 524
		hostdata->sensing = NULL;
	}

525 526 527
	cmd->scsi_done(cmd);
}

L
Linus Torvalds 已提交
528
/**
F
Finn Thain 已提交
529 530 531
 * NCR5380_queue_command - queue a command
 * @instance: the relevant SCSI adapter
 * @cmd: SCSI command
L
Linus Torvalds 已提交
532
 *
F
Finn Thain 已提交
533 534 535
 * cmd is added to the per-instance issue queue, with minor
 * twiddling done to the host specific fields of cmd.  If the
 * main coroutine is not running, it is restarted.
L
Linus Torvalds 已提交
536 537
 */

F
Finn Thain 已提交
538 539
static int NCR5380_queue_command(struct Scsi_Host *instance,
                                 struct scsi_cmnd *cmd)
L
Linus Torvalds 已提交
540
{
F
Finn Thain 已提交
541
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
542
	struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
F
Finn Thain 已提交
543
	unsigned long flags;
L
Linus Torvalds 已提交
544 545 546 547 548

#if (NDEBUG & NDEBUG_NO_WRITE)
	switch (cmd->cmnd[0]) {
	case WRITE_6:
	case WRITE_10:
549
		shost_printk(KERN_DEBUG, instance, "WRITE attempted with NDEBUG_NO_WRITE set\n");
L
Linus Torvalds 已提交
550
		cmd->result = (DID_ERROR << 16);
F
Finn Thain 已提交
551
		cmd->scsi_done(cmd);
L
Linus Torvalds 已提交
552 553
		return 0;
	}
554
#endif /* (NDEBUG & NDEBUG_NO_WRITE) */
L
Linus Torvalds 已提交
555 556 557

	cmd->result = 0;

558 559 560
	if (!NCR5380_acquire_dma_irq(instance))
		return SCSI_MLQUEUE_HOST_BUSY;

561
	spin_lock_irqsave(&hostdata->lock, flags);
F
Finn Thain 已提交
562

563 564
	/*
	 * Insert the cmd into the issue queue. Note that REQUEST SENSE
L
Linus Torvalds 已提交
565
	 * commands are added to the head of the queue since any command will
566
	 * clear the contingent allegiance condition that exists and the
L
Linus Torvalds 已提交
567 568 569
	 * sense data is only guaranteed to be valid while the condition exists.
	 */

570 571 572 573 574
	if (cmd->cmnd[0] == REQUEST_SENSE)
		list_add(&ncmd->list, &hostdata->unissued);
	else
		list_add_tail(&ncmd->list, &hostdata->unissued);

575
	spin_unlock_irqrestore(&hostdata->lock, flags);
F
Finn Thain 已提交
576

577 578
	dsprintk(NDEBUG_QUEUES, instance, "command %p added to %s of queue\n",
	         cmd, (cmd->cmnd[0] == REQUEST_SENSE) ? "head" : "tail");
L
Linus Torvalds 已提交
579 580

	/* Kick off command processing */
581
	queue_work(hostdata->work_q, &hostdata->main_task);
L
Linus Torvalds 已提交
582 583 584
	return 0;
}

585 586 587 588 589 590 591 592 593
static inline void maybe_release_dma_irq(struct Scsi_Host *instance)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);

	/* Caller does the locking needed to set & test these data atomically */
	if (list_empty(&hostdata->disconnected) &&
	    list_empty(&hostdata->unissued) &&
	    list_empty(&hostdata->autosense) &&
	    !hostdata->connected &&
594
	    !hostdata->selecting) {
595
		NCR5380_release_dma_irq(instance);
596
	}
597 598
}

F
Finn Thain 已提交
599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615
/**
 * dequeue_next_cmd - dequeue a command for processing
 * @instance: the scsi host instance
 *
 * Priority is given to commands on the autosense queue. These commands
 * need autosense because of a CHECK CONDITION result.
 *
 * Returns a command pointer if a command is found for a target that is
 * not already busy. Otherwise returns NULL.
 */

static struct scsi_cmnd *dequeue_next_cmd(struct Scsi_Host *instance)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
	struct NCR5380_cmd *ncmd;
	struct scsi_cmnd *cmd;

616
	if (hostdata->sensing || list_empty(&hostdata->autosense)) {
F
Finn Thain 已提交
617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648
		list_for_each_entry(ncmd, &hostdata->unissued, list) {
			cmd = NCR5380_to_scmd(ncmd);
			dsprintk(NDEBUG_QUEUES, instance, "dequeue: cmd=%p target=%d busy=0x%02x lun=%llu\n",
			         cmd, scmd_id(cmd), hostdata->busy[scmd_id(cmd)], cmd->device->lun);

			if (!(hostdata->busy[scmd_id(cmd)] & (1 << cmd->device->lun))) {
				list_del(&ncmd->list);
				dsprintk(NDEBUG_QUEUES, instance,
				         "dequeue: removed %p from issue queue\n", cmd);
				return cmd;
			}
		}
	} else {
		/* Autosense processing begins here */
		ncmd = list_first_entry(&hostdata->autosense,
		                        struct NCR5380_cmd, list);
		list_del(&ncmd->list);
		cmd = NCR5380_to_scmd(ncmd);
		dsprintk(NDEBUG_QUEUES, instance,
		         "dequeue: removed %p from autosense queue\n", cmd);
		scsi_eh_prep_cmnd(cmd, &hostdata->ses, NULL, 0, ~0);
		hostdata->sensing = cmd;
		return cmd;
	}
	return NULL;
}

static void requeue_cmd(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
	struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);

649
	if (hostdata->sensing == cmd) {
F
Finn Thain 已提交
650 651 652 653 654 655 656
		scsi_eh_restore_cmnd(cmd, &hostdata->ses);
		list_add(&ncmd->list, &hostdata->autosense);
		hostdata->sensing = NULL;
	} else
		list_add(&ncmd->list, &hostdata->unissued);
}

L
Linus Torvalds 已提交
657
/**
658
 * NCR5380_main - NCR state machines
L
Linus Torvalds 已提交
659
 *
660 661 662 663
 * NCR5380_main is a coroutine that runs as long as more work can
 * be done on the NCR5380 host adapters in a system.  Both
 * NCR5380_queue_command() and NCR5380_intr() will try to start it
 * in case it is not running.
L
Linus Torvalds 已提交
664 665
 */

D
David Howells 已提交
666
static void NCR5380_main(struct work_struct *work)
L
Linus Torvalds 已提交
667
{
D
David Howells 已提交
668
	struct NCR5380_hostdata *hostdata =
669
		container_of(work, struct NCR5380_hostdata, main_task);
L
Linus Torvalds 已提交
670 671
	struct Scsi_Host *instance = hostdata->host;
	int done;
672

L
Linus Torvalds 已提交
673 674
	do {
		done = 1;
675

F
Finn Thain 已提交
676
		spin_lock_irq(&hostdata->lock);
677 678 679 680 681
		while (!hostdata->connected && !hostdata->selecting) {
			struct scsi_cmnd *cmd = dequeue_next_cmd(instance);

			if (!cmd)
				break;
L
Linus Torvalds 已提交
682

F
Finn Thain 已提交
683
			dsprintk(NDEBUG_MAIN, instance, "main: dequeued %p\n", cmd);
684

F
Finn Thain 已提交
685 686 687 688 689 690 691 692 693 694 695 696
			/*
			 * Attempt to establish an I_T_L nexus here.
			 * On success, instance->hostdata->connected is set.
			 * On failure, we must add the command back to the
			 * issue queue so we can keep trying.
			 */
			/*
			 * REQUEST SENSE commands are issued without tagged
			 * queueing, even on SCSI-II devices because the
			 * contingent allegiance condition exists for the
			 * entire unit.
			 */
697

698
			if (!NCR5380_select(instance, cmd)) {
699
				dsprintk(NDEBUG_MAIN, instance, "main: select complete\n");
700
				maybe_release_dma_irq(instance);
F
Finn Thain 已提交
701 702 703 704 705 706
			} else {
				dsprintk(NDEBUG_MAIN | NDEBUG_QUEUES, instance,
				         "main: select failed, returning %p to queue\n", cmd);
				requeue_cmd(instance, cmd);
			}
		}
707
		if (hostdata->connected && !hostdata->dma_len) {
708
			dsprintk(NDEBUG_MAIN, instance, "main: performing information transfer\n");
L
Linus Torvalds 已提交
709 710
			NCR5380_information_transfer(instance);
			done = 0;
711
		}
712 713
		if (!hostdata->connected)
			NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
F
Finn Thain 已提交
714 715 716
		spin_unlock_irq(&hostdata->lock);
		if (!done)
			cond_resched();
L
Linus Torvalds 已提交
717 718 719
	} while (!done);
}

720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750
/*
 * NCR5380_dma_complete - finish DMA transfer
 * @instance: the scsi host instance
 *
 * Called by the interrupt handler when DMA finishes or a phase
 * mismatch occurs (which would end the DMA transfer).
 */

static void NCR5380_dma_complete(struct Scsi_Host *instance)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
	int transferred;
	unsigned char **data;
	int *count;
	int saved_data = 0, overrun = 0;
	unsigned char p;

	if (hostdata->read_overruns) {
		p = hostdata->connected->SCp.phase;
		if (p & SR_IO) {
			udelay(10);
			if ((NCR5380_read(BUS_AND_STATUS_REG) &
			     (BASR_PHASE_MATCH | BASR_ACK)) ==
			    (BASR_PHASE_MATCH | BASR_ACK)) {
				saved_data = NCR5380_read(INPUT_DATA_REG);
				overrun = 1;
				dsprintk(NDEBUG_DMA, instance, "read overrun handled\n");
			}
		}
	}

751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767
#ifdef CONFIG_SUN3
	if ((sun3scsi_dma_finish(rq_data_dir(hostdata->connected->request)))) {
		pr_err("scsi%d: overrun in UDC counter -- not prepared to deal with this!\n",
		       instance->host_no);
		BUG();
	}

	if ((NCR5380_read(BUS_AND_STATUS_REG) & (BASR_PHASE_MATCH | BASR_ACK)) ==
	    (BASR_PHASE_MATCH | BASR_ACK)) {
		pr_err("scsi%d: BASR %02x\n", instance->host_no,
		       NCR5380_read(BUS_AND_STATUS_REG));
		pr_err("scsi%d: bus stuck in data phase -- probably a single byte overrun!\n",
		       instance->host_no);
		BUG();
	}
#endif

768 769 770 771
	NCR5380_write(MODE_REG, MR_BASE);
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
	NCR5380_read(RESET_PARITY_INTERRUPT_REG);

772
	transferred = hostdata->dma_len - NCR5380_dma_residual(hostdata);
773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802
	hostdata->dma_len = 0;

	data = (unsigned char **)&hostdata->connected->SCp.ptr;
	count = &hostdata->connected->SCp.this_residual;
	*data += transferred;
	*count -= transferred;

	if (hostdata->read_overruns) {
		int cnt, toPIO;

		if ((NCR5380_read(STATUS_REG) & PHASE_MASK) == p && (p & SR_IO)) {
			cnt = toPIO = hostdata->read_overruns;
			if (overrun) {
				dsprintk(NDEBUG_DMA, instance,
				         "Got an input overrun, using saved byte\n");
				*(*data)++ = saved_data;
				(*count)--;
				cnt--;
				toPIO--;
			}
			if (toPIO > 0) {
				dsprintk(NDEBUG_DMA, instance,
				         "Doing %d byte PIO to 0x%p\n", cnt, *data);
				NCR5380_transfer_pio(instance, &p, &cnt, data);
				*count -= toPIO - cnt;
			}
		}
	}
}

L
Linus Torvalds 已提交
803
/**
804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834
 * NCR5380_intr - generic NCR5380 irq handler
 * @irq: interrupt number
 * @dev_id: device info
 *
 * Handle interrupts, reestablishing I_T_L or I_T_L_Q nexuses
 * from the disconnected queue, and restarting NCR5380_main()
 * as required.
 *
 * The chip can assert IRQ in any of six different conditions. The IRQ flag
 * is then cleared by reading the Reset Parity/Interrupt Register (RPIR).
 * Three of these six conditions are latched in the Bus and Status Register:
 * - End of DMA (cleared by ending DMA Mode)
 * - Parity error (cleared by reading RPIR)
 * - Loss of BSY (cleared by reading RPIR)
 * Two conditions have flag bits that are not latched:
 * - Bus phase mismatch (non-maskable in DMA Mode, cleared by ending DMA Mode)
 * - Bus reset (non-maskable)
 * The remaining condition has no flag bit at all:
 * - Selection/reselection
 *
 * Hence, establishing the cause(s) of any interrupt is partly guesswork.
 * In "The DP8490 and DP5380 Comparison Guide", National Semiconductor
 * claimed that "the design of the [DP8490] interrupt logic ensures
 * interrupts will not be lost (they can be on the DP5380)."
 * The L5380/53C80 datasheet from LOGIC Devices has more details.
 *
 * Checking for bus reset by reading RST is futile because of interrupt
 * latency, but a bus reset will reset chip logic. Checking for parity error
 * is unnecessary because that interrupt is never enabled. A Loss of BSY
 * condition will clear DMA Mode. We can tell when this occurs because the
 * the Busy Monitor interrupt is enabled together with DMA Mode.
L
Linus Torvalds 已提交
835 836
 */

837
static irqreturn_t __maybe_unused NCR5380_intr(int irq, void *dev_id)
L
Linus Torvalds 已提交
838
{
839
	struct Scsi_Host *instance = dev_id;
840 841
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
	int handled = 0;
L
Linus Torvalds 已提交
842 843 844
	unsigned char basr;
	unsigned long flags;

845
	spin_lock_irqsave(&hostdata->lock, flags);
846 847 848 849 850 851

	basr = NCR5380_read(BUS_AND_STATUS_REG);
	if (basr & BASR_IRQ) {
		unsigned char mr = NCR5380_read(MODE_REG);
		unsigned char sr = NCR5380_read(STATUS_REG);

852 853
		dsprintk(NDEBUG_INTR, instance, "IRQ %d, BASR 0x%02x, SR 0x%02x, MR 0x%02x\n",
		         irq, basr, sr, mr);
L
Linus Torvalds 已提交
854

855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870
		if ((mr & MR_DMA_MODE) || (mr & MR_MONITOR_BSY)) {
			/* Probably End of DMA, Phase Mismatch or Loss of BSY.
			 * We ack IRQ after clearing Mode Register. Workarounds
			 * for End of DMA errata need to happen in DMA Mode.
			 */

			dsprintk(NDEBUG_INTR, instance, "interrupt in DMA mode\n");

			if (hostdata->connected) {
				NCR5380_dma_complete(instance);
				queue_work(hostdata->work_q, &hostdata->main_task);
			} else {
				NCR5380_write(MODE_REG, MR_BASE);
				NCR5380_read(RESET_PARITY_INTERRUPT_REG);
			}
		} else if ((NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_mask) &&
871 872 873 874 875
		    (sr & (SR_SEL | SR_IO | SR_BSY | SR_RST)) == (SR_SEL | SR_IO)) {
			/* Probably reselected */
			NCR5380_write(SELECT_ENABLE_REG, 0);
			NCR5380_read(RESET_PARITY_INTERRUPT_REG);

876
			dsprintk(NDEBUG_INTR, instance, "interrupt with SEL and IO\n");
877 878 879 880

			if (!hostdata->connected) {
				NCR5380_reselect(instance);
				queue_work(hostdata->work_q, &hostdata->main_task);
L
Linus Torvalds 已提交
881
			}
882 883 884 885 886 887
			if (!hostdata->connected)
				NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
		} else {
			/* Probably Bus Reset */
			NCR5380_read(RESET_PARITY_INTERRUPT_REG);

888
			dsprintk(NDEBUG_INTR, instance, "unknown interrupt\n");
889 890 891
#ifdef SUN3_SCSI_VME
			dregs->csr |= CSR_DMA_ENABLE;
#endif
892 893 894
		}
		handled = 1;
	} else {
895
		dsprintk(NDEBUG_INTR, instance, "interrupt without IRQ bit\n");
896 897 898
#ifdef SUN3_SCSI_VME
		dregs->csr |= CSR_DMA_ENABLE;
#endif
899 900
	}

901
	spin_unlock_irqrestore(&hostdata->lock, flags);
902 903

	return IRQ_RETVAL(handled);
L
Linus Torvalds 已提交
904 905
}

906 907 908 909
/**
 * NCR5380_select - attempt arbitration and selection for a given command
 * @instance: the Scsi_Host instance
 * @cmd: the scsi_cmnd to execute
L
Linus Torvalds 已提交
910
 *
911 912
 * This routine establishes an I_T_L nexus for a SCSI command. This involves
 * ARBITRATION, SELECTION and MESSAGE OUT phases and an IDENTIFY message.
913
 *
914 915
 * Returns true if the operation should be retried.
 * Returns false if it should not be retried.
L
Linus Torvalds 已提交
916
 *
917
 * Side effects :
918 919 920 921
 * If bus busy, arbitration failed, etc, NCR5380_select() will exit
 * with registers as they should have been on entry - ie
 * SELECT_ENABLE will be set appropriately, the NCR5380
 * will cease to drive any SCSI bus signals.
L
Linus Torvalds 已提交
922
 *
923 924
 * If successful : the I_T_L nexus will be established, and
 * hostdata->connected will be set to cmd.
925
 * SELECT interrupt will be disabled.
L
Linus Torvalds 已提交
926
 *
927 928
 * If failed (no target) : cmd->scsi_done() will be called, and the
 * cmd->result host byte set to DID_BAD_TARGET.
L
Linus Torvalds 已提交
929
 */
930

931
static bool NCR5380_select(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
932
	__releases(&hostdata->lock) __acquires(&hostdata->lock)
L
Linus Torvalds 已提交
933
{
F
Finn Thain 已提交
934
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
935 936 937 938
	unsigned char tmp[3], phase;
	unsigned char *data;
	int len;
	int err;
939
	bool ret = true;
940 941
	bool can_disconnect = instance->irq != NO_IRQ &&
			      cmd->cmnd[0] != REQUEST_SENSE;
L
Linus Torvalds 已提交
942 943

	NCR5380_dprint(NDEBUG_ARBITRATION, instance);
944 945
	dsprintk(NDEBUG_ARBITRATION, instance, "starting arbitration, id = %d\n",
	         instance->this_id);
L
Linus Torvalds 已提交
946

947 948 949
	/*
	 * Arbitration and selection phases are slow and involve dropping the
	 * lock, so we have to watch out for EH. An exception handler may
950
	 * change 'selecting' to NULL. This function will then return false
951 952 953 954 955
	 * so that the caller will forget about 'cmd'. (During information
	 * transfer phases, EH may change 'connected' to NULL.)
	 */
	hostdata->selecting = cmd;

956 957
	/*
	 * Set the phase bits to 0, otherwise the NCR5380 won't drive the
L
Linus Torvalds 已提交
958 959 960 961 962
	 * data bus during SELECTION.
	 */

	NCR5380_write(TARGET_COMMAND_REG, 0);

963
	/*
L
Linus Torvalds 已提交
964 965 966 967 968 969
	 * Start arbitration.
	 */

	NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
	NCR5380_write(MODE_REG, MR_ARBITRATE);

970 971 972
	/* The chip now waits for BUS FREE phase. Then after the 800 ns
	 * Bus Free Delay, arbitration will begin.
	 */
L
Linus Torvalds 已提交
973

974
	spin_unlock_irq(&hostdata->lock);
975
	err = NCR5380_poll_politely2(hostdata, MODE_REG, MR_ARBITRATE, 0,
976 977
	                INITIATOR_COMMAND_REG, ICR_ARBITRATION_PROGRESS,
	                                       ICR_ARBITRATION_PROGRESS, HZ);
978
	spin_lock_irq(&hostdata->lock);
979 980
	if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE)) {
		/* Reselection interrupt */
981
		goto out;
982
	}
983 984 985
	if (!hostdata->selecting) {
		/* Command was aborted */
		NCR5380_write(MODE_REG, MR_BASE);
986
		return false;
987
	}
988 989 990 991
	if (err < 0) {
		NCR5380_write(MODE_REG, MR_BASE);
		shost_printk(KERN_ERR, instance,
		             "select: arbitration timeout\n");
992
		goto out;
L
Linus Torvalds 已提交
993
	}
994
	spin_unlock_irq(&hostdata->lock);
L
Linus Torvalds 已提交
995

996
	/* The SCSI-2 arbitration delay is 2.4 us */
L
Linus Torvalds 已提交
997 998 999
	udelay(3);

	/* Check for lost arbitration */
1000 1001 1002
	if ((NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST) ||
	    (NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_higher_mask) ||
	    (NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST)) {
L
Linus Torvalds 已提交
1003
		NCR5380_write(MODE_REG, MR_BASE);
1004
		dsprintk(NDEBUG_ARBITRATION, instance, "lost arbitration, deasserting MR_ARBITRATE\n");
1005
		spin_lock_irq(&hostdata->lock);
1006
		goto out;
L
Linus Torvalds 已提交
1007
	}
1008 1009 1010 1011 1012 1013 1014

	/* After/during arbitration, BSY should be asserted.
	 * IBM DPES-31080 Version S31Q works now
	 * Tnx to Thomas_Roesch@m2.maus.de for finding this! (Roman)
	 */
	NCR5380_write(INITIATOR_COMMAND_REG,
		      ICR_BASE | ICR_ASSERT_SEL | ICR_ASSERT_BSY);
L
Linus Torvalds 已提交
1015

1016 1017
	/*
	 * Again, bus clear + bus settle time is 1.2us, however, this is
L
Linus Torvalds 已提交
1018 1019 1020
	 * a minimum so we'll udelay ceil(1.2)
	 */

1021 1022 1023 1024
	if (hostdata->flags & FLAG_TOSHIBA_DELAY)
		udelay(15);
	else
		udelay(2);
L
Linus Torvalds 已提交
1025

1026 1027
	spin_lock_irq(&hostdata->lock);

1028 1029
	/* NCR5380_reselect() clears MODE_REG after a reselection interrupt */
	if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE))
1030 1031 1032 1033 1034
		goto out;

	if (!hostdata->selecting) {
		NCR5380_write(MODE_REG, MR_BASE);
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1035
		return false;
1036
	}
1037

1038
	dsprintk(NDEBUG_ARBITRATION, instance, "won arbitration\n");
L
Linus Torvalds 已提交
1039

1040 1041
	/*
	 * Now that we have won arbitration, start Selection process, asserting
L
Linus Torvalds 已提交
1042 1043 1044
	 * the host and target ID's on the SCSI bus.
	 */

1045
	NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask | (1 << scmd_id(cmd)));
L
Linus Torvalds 已提交
1046

1047
	/*
L
Linus Torvalds 已提交
1048 1049 1050 1051 1052
	 * Raise ATN while SEL is true before BSY goes false from arbitration,
	 * since this is the only way to guarantee that we'll get a MESSAGE OUT
	 * phase immediately after selection.
	 */

1053 1054
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY |
	              ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_SEL);
L
Linus Torvalds 已提交
1055 1056
	NCR5380_write(MODE_REG, MR_BASE);

1057
	/*
L
Linus Torvalds 已提交
1058 1059 1060 1061 1062
	 * Reselect interrupts must be turned off prior to the dropping of BSY,
	 * otherwise we will trigger an interrupt.
	 */
	NCR5380_write(SELECT_ENABLE_REG, 0);

1063 1064
	spin_unlock_irq(&hostdata->lock);

L
Linus Torvalds 已提交
1065
	/*
1066
	 * The initiator shall then wait at least two deskew delays and release
L
Linus Torvalds 已提交
1067 1068
	 * the BSY signal.
	 */
1069
	udelay(1);        /* wingel -- wait two bus deskew delay >2*45ns */
L
Linus Torvalds 已提交
1070 1071

	/* Reset BSY */
1072 1073
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA |
	              ICR_ASSERT_ATN | ICR_ASSERT_SEL);
L
Linus Torvalds 已提交
1074

1075
	/*
L
Linus Torvalds 已提交
1076
	 * Something weird happens when we cease to drive BSY - looks
1077
	 * like the board/chip is letting us do another read before the
L
Linus Torvalds 已提交
1078 1079 1080 1081 1082
	 * appropriate propagation delay has expired, and we're confusing
	 * a BSY signal from ourselves as the target's response to SELECTION.
	 *
	 * A small delay (the 'C++' frontend breaks the pipeline with an
	 * unnecessary jump, making it work on my 386-33/Trantor T128, the
1083 1084 1085
	 * tighter 'C' code breaks and requires this) solves the problem -
	 * the 1 us delay is arbitrary, and only used because this delay will
	 * be the same on other platforms and since it works here, it should
L
Linus Torvalds 已提交
1086 1087 1088 1089 1090 1091 1092 1093
	 * work there.
	 *
	 * wingel suggests that this could be due to failing to wait
	 * one deskew delay.
	 */

	udelay(1);

1094
	dsprintk(NDEBUG_SELECTION, instance, "selecting target %d\n", scmd_id(cmd));
L
Linus Torvalds 已提交
1095

1096 1097
	/*
	 * The SCSI specification calls for a 250 ms timeout for the actual
L
Linus Torvalds 已提交
1098 1099 1100
	 * selection.
	 */

1101
	err = NCR5380_poll_politely(hostdata, STATUS_REG, SR_BSY, SR_BSY,
F
Finn Thain 已提交
1102
	                            msecs_to_jiffies(250));
L
Linus Torvalds 已提交
1103 1104

	if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
1105
		spin_lock_irq(&hostdata->lock);
L
Linus Torvalds 已提交
1106 1107
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
		NCR5380_reselect(instance);
1108
		shost_printk(KERN_ERR, instance, "reselection after won arbitration?\n");
1109
		goto out;
L
Linus Torvalds 已提交
1110
	}
F
Finn Thain 已提交
1111 1112

	if (err < 0) {
1113
		spin_lock_irq(&hostdata->lock);
F
Finn Thain 已提交
1114
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1115

1116
		/* Can't touch cmd if it has been reclaimed by the scsi ML */
1117
		if (!hostdata->selecting)
1118
			return false;
1119 1120 1121 1122 1123

		cmd->result = DID_BAD_TARGET << 16;
		complete_cmd(instance, cmd);
		dsprintk(NDEBUG_SELECTION, instance,
			"target did not respond within 250ms\n");
1124
		ret = false;
1125
		goto out;
F
Finn Thain 已提交
1126 1127
	}

1128 1129 1130
	/*
	 * No less than two deskew delays after the initiator detects the
	 * BSY signal is true, it shall release the SEL signal and may
L
Linus Torvalds 已提交
1131 1132 1133 1134 1135 1136 1137 1138
	 * change the DATA BUS.                                     -wingel
	 */

	udelay(1);

	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);

	/*
1139
	 * Since we followed the SCSI spec, and raised ATN while SEL
L
Linus Torvalds 已提交
1140 1141 1142 1143 1144 1145 1146
	 * was true but before BSY was false during selection, the information
	 * transfer phase should be a MESSAGE OUT phase so that we can send the
	 * IDENTIFY message.
	 */

	/* Wait for start of REQ/ACK handshake */

1147
	err = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, HZ);
1148
	spin_lock_irq(&hostdata->lock);
1149
	if (err < 0) {
1150 1151
		shost_printk(KERN_ERR, instance, "select: REQ timeout\n");
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1152 1153 1154 1155
		goto out;
	}
	if (!hostdata->selecting) {
		do_abort(instance);
1156
		return false;
L
Linus Torvalds 已提交
1157 1158
	}

1159 1160
	dsprintk(NDEBUG_SELECTION, instance, "target %d selected, going into MESSAGE OUT phase.\n",
	         scmd_id(cmd));
1161
	tmp[0] = IDENTIFY(can_disconnect, cmd->device->lun);
L
Linus Torvalds 已提交
1162 1163 1164 1165 1166

	len = 1;
	data = tmp;
	phase = PHASE_MSGOUT;
	NCR5380_transfer_pio(instance, &phase, &len, &data);
1167 1168 1169 1170 1171
	if (len) {
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
		cmd->result = DID_ERROR << 16;
		complete_cmd(instance, cmd);
		dsprintk(NDEBUG_SELECTION, instance, "IDENTIFY message transfer failed\n");
1172
		ret = false;
1173 1174 1175
		goto out;
	}

1176
	dsprintk(NDEBUG_SELECTION, instance, "nexus established.\n");
1177

L
Linus Torvalds 已提交
1178
	hostdata->connected = cmd;
1179
	hostdata->busy[cmd->device->id] |= 1 << cmd->device->lun;
L
Linus Torvalds 已提交
1180

1181 1182 1183 1184
#ifdef SUN3_SCSI_VME
	dregs->csr |= CSR_INTR;
#endif

1185
	initialize_SCp(cmd);
L
Linus Torvalds 已提交
1186

1187
	ret = false;
1188 1189 1190 1191 1192

out:
	if (!hostdata->selecting)
		return NULL;
	hostdata->selecting = NULL;
1193
	return ret;
L
Linus Torvalds 已提交
1194 1195
}

1196 1197
/*
 * Function : int NCR5380_transfer_pio (struct Scsi_Host *instance,
1198
 * unsigned char *phase, int *count, unsigned char **data)
L
Linus Torvalds 已提交
1199 1200 1201
 *
 * Purpose : transfers data in given phase using polled I/O
 *
1202
 * Inputs : instance - instance of driver, *phase - pointer to
1203 1204
 * what phase is expected, *count - pointer to number of
 * bytes to transfer, **data - pointer to data pointer.
1205
 *
L
Linus Torvalds 已提交
1206
 * Returns : -1 when different phase is entered without transferring
1207
 * maximum number of bytes, 0 if all bytes are transferred or exit
1208
 * is in same phase.
L
Linus Torvalds 已提交
1209
 *
1210
 * Also, *phase, *count, *data are modified in place.
L
Linus Torvalds 已提交
1211 1212 1213 1214 1215
 *
 * XXX Note : handling for bus free may be useful.
 */

/*
1216
 * Note : this code is not as quick as it could be, however it
L
Linus Torvalds 已提交
1217 1218 1219 1220
 * IS 100% reliable, and for the actual data transfer where speed
 * counts, we will always do a pseudo DMA or DMA transfer.
 */

1221 1222 1223 1224
static int NCR5380_transfer_pio(struct Scsi_Host *instance,
				unsigned char *phase, int *count,
				unsigned char **data)
{
1225
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
1226 1227 1228 1229
	unsigned char p = *phase, tmp;
	int c = *count;
	unsigned char *d = *data;

1230 1231
	/*
	 * The NCR5380 chip will only drive the SCSI bus when the
L
Linus Torvalds 已提交
1232 1233 1234 1235
	 * phase specified in the appropriate bits of the TARGET COMMAND
	 * REGISTER match the STATUS REGISTER
	 */

1236
	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
L
Linus Torvalds 已提交
1237 1238

	do {
1239 1240 1241
		/*
		 * Wait for assertion of REQ, after which the phase bits will be
		 * valid
L
Linus Torvalds 已提交
1242 1243
		 */

1244
		if (NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, HZ) < 0)
L
Linus Torvalds 已提交
1245 1246
			break;

1247
		dsprintk(NDEBUG_HANDSHAKE, instance, "REQ asserted\n");
L
Linus Torvalds 已提交
1248 1249

		/* Check for phase mismatch */
1250
		if ((NCR5380_read(STATUS_REG) & PHASE_MASK) != p) {
1251 1252
			dsprintk(NDEBUG_PIO, instance, "phase mismatch\n");
			NCR5380_dprint_phase(NDEBUG_PIO, instance);
L
Linus Torvalds 已提交
1253 1254
			break;
		}
1255

L
Linus Torvalds 已提交
1256 1257 1258 1259 1260 1261 1262 1263
		/* Do actual transfer from SCSI bus to / from memory */
		if (!(p & SR_IO))
			NCR5380_write(OUTPUT_DATA_REG, *d);
		else
			*d = NCR5380_read(CURRENT_SCSI_DATA_REG);

		++d;

1264
		/*
L
Linus Torvalds 已提交
1265 1266 1267 1268 1269 1270 1271 1272 1273 1274
		 * The SCSI standard suggests that in MSGOUT phase, the initiator
		 * should drop ATN on the last byte of the message phase
		 * after REQ has been asserted for the handshake but before
		 * the initiator raises ACK.
		 */

		if (!(p & SR_IO)) {
			if (!((p & SR_MSG) && c > 1)) {
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA);
				NCR5380_dprint(NDEBUG_PIO, instance);
1275 1276
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
				              ICR_ASSERT_DATA | ICR_ASSERT_ACK);
L
Linus Torvalds 已提交
1277
			} else {
1278 1279
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
				              ICR_ASSERT_DATA | ICR_ASSERT_ATN);
L
Linus Torvalds 已提交
1280
				NCR5380_dprint(NDEBUG_PIO, instance);
1281 1282
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
				              ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_ACK);
L
Linus Torvalds 已提交
1283 1284 1285 1286 1287 1288
			}
		} else {
			NCR5380_dprint(NDEBUG_PIO, instance);
			NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK);
		}

1289
		if (NCR5380_poll_politely(hostdata,
1290 1291 1292
		                          STATUS_REG, SR_REQ, 0, 5 * HZ) < 0)
			break;

1293
		dsprintk(NDEBUG_HANDSHAKE, instance, "REQ negated, handshake complete\n");
L
Linus Torvalds 已提交
1294 1295

/*
1296 1297
 * We have several special cases to consider during REQ/ACK handshaking :
 * 1.  We were in MSGOUT phase, and we are on the last byte of the
1298
 * message.  ATN must be dropped as ACK is dropped.
L
Linus Torvalds 已提交
1299
 *
1300
 * 2.  We are in a MSGIN phase, and we are on the last byte of the
1301 1302
 * message.  We must exit with ACK asserted, so that the calling
 * code may raise ATN before dropping ACK to reject the message.
L
Linus Torvalds 已提交
1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313
 *
 * 3.  ACK and ATN are clear and the target may proceed as normal.
 */
		if (!(p == PHASE_MSGIN && c == 1)) {
			if (p == PHASE_MSGOUT && c > 1)
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
			else
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
		}
	} while (--c);

1314
	dsprintk(NDEBUG_PIO, instance, "residual %d\n", c);
L
Linus Torvalds 已提交
1315 1316 1317 1318

	*count = c;
	*data = d;
	tmp = NCR5380_read(STATUS_REG);
1319 1320 1321 1322 1323
	/* The phase read from the bus is valid if either REQ is (already)
	 * asserted or if ACK hasn't been released yet. The latter applies if
	 * we're in MSG IN, DATA IN or STATUS and all bytes have been received.
	 */
	if ((tmp & SR_REQ) || ((tmp & SR_IO) && c == 0))
L
Linus Torvalds 已提交
1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334
		*phase = tmp & PHASE_MASK;
	else
		*phase = PHASE_UNKNOWN;

	if (!c || (*phase == p))
		return 0;
	else
		return -1;
}

/**
1335 1336
 * do_reset - issue a reset command
 * @instance: adapter to reset
L
Linus Torvalds 已提交
1337
 *
1338 1339
 * Issue a reset sequence to the NCR5380 and try and get the bus
 * back into sane shape.
L
Linus Torvalds 已提交
1340
 *
1341 1342 1343
 * This clears the reset interrupt flag because there may be no handler for
 * it. When the driver is initialized, the NCR5380_intr() handler has not yet
 * been installed. And when in EH we may have released the ST DMA interrupt.
L
Linus Torvalds 已提交
1344
 */
1345

1346 1347
static void do_reset(struct Scsi_Host *instance)
{
1348
	struct NCR5380_hostdata __maybe_unused *hostdata = shost_priv(instance);
1349 1350 1351 1352 1353
	unsigned long flags;

	local_irq_save(flags);
	NCR5380_write(TARGET_COMMAND_REG,
	              PHASE_SR_TO_TCR(NCR5380_read(STATUS_REG) & PHASE_MASK));
L
Linus Torvalds 已提交
1354
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST);
1355
	udelay(50);
L
Linus Torvalds 已提交
1356
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1357 1358
	(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
	local_irq_restore(flags);
L
Linus Torvalds 已提交
1359 1360
}

1361 1362 1363 1364
/**
 * do_abort - abort the currently established nexus by going to
 * MESSAGE OUT phase and sending an ABORT message.
 * @instance: relevant scsi host instance
L
Linus Torvalds 已提交
1365
 *
1366
 * Returns 0 on success, -1 on failure.
L
Linus Torvalds 已提交
1367 1368
 */

1369 1370
static int do_abort(struct Scsi_Host *instance)
{
1371
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
1372 1373 1374 1375 1376 1377 1378
	unsigned char *msgptr, phase, tmp;
	int len;
	int rc;

	/* Request message out phase */
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);

1379 1380 1381 1382
	/*
	 * Wait for the target to indicate a valid phase by asserting
	 * REQ.  Once this happens, we'll have either a MSGOUT phase
	 * and can immediately send the ABORT message, or we'll have some
L
Linus Torvalds 已提交
1383
	 * other phase and will have to source/sink data.
1384
	 *
L
Linus Torvalds 已提交
1385 1386 1387 1388
	 * We really don't care what value was on the bus or what value
	 * the target sees, so we just handshake.
	 */

1389
	rc = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, 10 * HZ);
1390
	if (rc < 0)
1391
		goto timeout;
L
Linus Torvalds 已提交
1392

1393
	tmp = NCR5380_read(STATUS_REG) & PHASE_MASK;
1394

L
Linus Torvalds 已提交
1395 1396
	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp));

1397
	if (tmp != PHASE_MSGOUT) {
1398 1399
		NCR5380_write(INITIATOR_COMMAND_REG,
		              ICR_BASE | ICR_ASSERT_ATN | ICR_ASSERT_ACK);
1400
		rc = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, 0, 3 * HZ);
1401
		if (rc < 0)
1402 1403
			goto timeout;
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
L
Linus Torvalds 已提交
1404
	}
1405

L
Linus Torvalds 已提交
1406 1407 1408 1409
	tmp = ABORT;
	msgptr = &tmp;
	len = 1;
	phase = PHASE_MSGOUT;
1410
	NCR5380_transfer_pio(instance, &phase, &len, &msgptr);
L
Linus Torvalds 已提交
1411 1412 1413 1414 1415 1416 1417

	/*
	 * If we got here, and the command completed successfully,
	 * we're about to go into bus free state.
	 */

	return len ? -1 : 0;
1418 1419 1420 1421

timeout:
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
	return -1;
L
Linus Torvalds 已提交
1422 1423
}

1424 1425
/*
 * Function : int NCR5380_transfer_dma (struct Scsi_Host *instance,
1426
 * unsigned char *phase, int *count, unsigned char **data)
L
Linus Torvalds 已提交
1427 1428
 *
 * Purpose : transfers data in given phase using either real
1429
 * or pseudo DMA.
L
Linus Torvalds 已提交
1430
 *
1431
 * Inputs : instance - instance of driver, *phase - pointer to
1432 1433
 * what phase is expected, *count - pointer to number of
 * bytes to transfer, **data - pointer to data pointer.
1434
 *
L
Linus Torvalds 已提交
1435
 * Returns : -1 when different phase is entered without transferring
1436 1437
 * maximum number of bytes, 0 if all bytes or transferred or exit
 * is in same phase.
L
Linus Torvalds 已提交
1438
 *
1439
 * Also, *phase, *count, *data are modified in place.
L
Linus Torvalds 已提交
1440 1441 1442
 */


1443 1444 1445 1446 1447
static int NCR5380_transfer_dma(struct Scsi_Host *instance,
				unsigned char *phase, int *count,
				unsigned char **data)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
1448 1449 1450
	int c = *count;
	unsigned char p = *phase;
	unsigned char *d = *data;
L
Linus Torvalds 已提交
1451
	unsigned char tmp;
1452
	int result = 0;
L
Linus Torvalds 已提交
1453 1454 1455 1456 1457 1458

	if ((tmp = (NCR5380_read(STATUS_REG) & PHASE_MASK)) != p) {
		*phase = tmp;
		return -1;
	}

1459
	hostdata->connected->SCp.phase = p;
L
Linus Torvalds 已提交
1460

1461 1462 1463 1464 1465 1466
	if (p & SR_IO) {
		if (hostdata->read_overruns)
			c -= hostdata->read_overruns;
		else if (hostdata->flags & FLAG_DMA_FIXUP)
			--c;
	}
L
Linus Torvalds 已提交
1467

1468 1469
	dsprintk(NDEBUG_DMA, instance, "initializing DMA %s: length %d, address %p\n",
	         (p & SR_IO) ? "receive" : "send", c, d);
L
Linus Torvalds 已提交
1470

1471 1472 1473 1474 1475
#ifdef CONFIG_SUN3
	/* send start chain */
	sun3scsi_dma_start(c, *data);
#endif

1476 1477 1478 1479 1480 1481 1482 1483 1484
	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
	NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
	                        MR_ENABLE_EOP_INTR);

	if (!(hostdata->flags & FLAG_LATE_DMA_SETUP)) {
		/* On the Medusa, it is a must to initialize the DMA before
		 * starting the NCR. This is also the cleaner way for the TT.
		 */
		if (p & SR_IO)
1485
			result = NCR5380_dma_recv_setup(hostdata, d, c);
1486
		else
1487
			result = NCR5380_dma_send_setup(hostdata, d, c);
1488
	}
L
Linus Torvalds 已提交
1489

1490
	/*
1491 1492
	 * On the PAS16 at least I/O recovery delays are not needed here.
	 * Everyone else seems to want them.
L
Linus Torvalds 已提交
1493 1494 1495
	 */

	if (p & SR_IO) {
1496
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1497
		NCR5380_io_delay(1);
L
Linus Torvalds 已提交
1498 1499
		NCR5380_write(START_DMA_INITIATOR_RECEIVE_REG, 0);
	} else {
1500
		NCR5380_io_delay(1);
L
Linus Torvalds 已提交
1501
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA);
1502
		NCR5380_io_delay(1);
L
Linus Torvalds 已提交
1503
		NCR5380_write(START_DMA_SEND_REG, 0);
1504
		NCR5380_io_delay(1);
L
Linus Torvalds 已提交
1505 1506
	}

1507 1508 1509 1510 1511 1512 1513
#ifdef CONFIG_SUN3
#ifdef SUN3_SCSI_VME
	dregs->csr |= CSR_DMA_ENABLE;
#endif
	sun3_dma_active = 1;
#endif

1514 1515 1516 1517 1518
	if (hostdata->flags & FLAG_LATE_DMA_SETUP) {
		/* On the Falcon, the DMA setup must be done after the last
		 * NCR access, else the DMA setup gets trashed!
		 */
		if (p & SR_IO)
1519
			result = NCR5380_dma_recv_setup(hostdata, d, c);
1520
		else
1521
			result = NCR5380_dma_send_setup(hostdata, d, c);
1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536
	}

	/* On failure, NCR5380_dma_xxxx_setup() returns a negative int. */
	if (result < 0)
		return result;

	/* For real DMA, result is the byte count. DMA interrupt is expected. */
	if (result > 0) {
		hostdata->dma_len = result;
		return 0;
	}

	/* The result is zero iff pseudo DMA send/receive was completed. */
	hostdata->dma_len = c;

L
Linus Torvalds 已提交
1537
/*
1538
 * A note regarding the DMA errata workarounds for early NMOS silicon.
F
Finn Thain 已提交
1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563 1564
 *
 * For DMA sends, we want to wait until the last byte has been
 * transferred out over the bus before we turn off DMA mode.  Alas, there
 * seems to be no terribly good way of doing this on a 5380 under all
 * conditions.  For non-scatter-gather operations, we can wait until REQ
 * and ACK both go false, or until a phase mismatch occurs.  Gather-sends
 * are nastier, since the device will be expecting more data than we
 * are prepared to send it, and REQ will remain asserted.  On a 53C8[01] we
 * could test Last Byte Sent to assure transfer (I imagine this is precisely
 * why this signal was added to the newer chips) but on the older 538[01]
 * this signal does not exist.  The workaround for this lack is a watchdog;
 * we bail out of the wait-loop after a modest amount of wait-time if
 * the usual exit conditions are not met.  Not a terribly clean or
 * correct solution :-%
 *
 * DMA receive is equally tricky due to a nasty characteristic of the NCR5380.
 * If the chip is in DMA receive mode, it will respond to a target's
 * REQ by latching the SCSI data into the INPUT DATA register and asserting
 * ACK, even if it has _already_ been notified by the DMA controller that
 * the current DMA transfer has completed!  If the NCR5380 is then taken
 * out of DMA mode, this already-acknowledged byte is lost. This is
 * not a problem for "one DMA transfer per READ command", because
 * the situation will never arise... either all of the data is DMA'ed
 * properly, or the target switches to MESSAGE IN phase to signal a
 * disconnection (either operation bringing the DMA to a clean halt).
 * However, in order to handle scatter-receive, we must work around the
1565
 * problem.  The chosen fix is to DMA fewer bytes, then check for the
F
Finn Thain 已提交
1566 1567 1568
 * condition before taking the NCR5380 out of DMA mode.  One or two extra
 * bytes are transferred via PIO as necessary to fill out the original
 * request.
L
Linus Torvalds 已提交
1569 1570
 */

1571 1572
	if (hostdata->flags & FLAG_DMA_FIXUP) {
		if (p & SR_IO) {
L
Linus Torvalds 已提交
1573
			/*
1574
			 * The workaround was to transfer fewer bytes than we
1575
			 * intended to with the pseudo-DMA read function, wait for
L
Linus Torvalds 已提交
1576 1577
			 * the chip to latch the last byte, read it, and then disable
			 * pseudo-DMA mode.
1578
			 *
L
Linus Torvalds 已提交
1579 1580 1581 1582
			 * After REQ is asserted, the NCR5380 asserts DRQ and ACK.
			 * REQ is deasserted when ACK is asserted, and not reasserted
			 * until ACK goes false.  Since the NCR5380 won't lower ACK
			 * until DACK is asserted, which won't happen unless we twiddle
1583 1584
			 * the DMA port or we take the NCR5380 out of DMA mode, we
			 * can guarantee that we won't handshake another extra
L
Linus Torvalds 已提交
1585 1586 1587
			 * byte.
			 */

1588
			if (NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG,
1589
			                          BASR_DRQ, BASR_DRQ, HZ) < 0) {
1590
				result = -1;
1591 1592
				shost_printk(KERN_ERR, instance, "PDMA read: DRQ timeout\n");
			}
1593
			if (NCR5380_poll_politely(hostdata, STATUS_REG,
1594
			                          SR_REQ, 0, HZ) < 0) {
1595
				result = -1;
1596
				shost_printk(KERN_ERR, instance, "PDMA read: !REQ timeout\n");
L
Linus Torvalds 已提交
1597
			}
1598 1599
			d[*count - 1] = NCR5380_read(INPUT_DATA_REG);
		} else {
L
Linus Torvalds 已提交
1600
			/*
1601 1602
			 * Wait for the last byte to be sent.  If REQ is being asserted for
			 * the byte we're interested, we'll ACK it and it will go false.
L
Linus Torvalds 已提交
1603
			 */
1604
			if (NCR5380_poll_politely2(hostdata,
1605 1606
			     BUS_AND_STATUS_REG, BASR_DRQ, BASR_DRQ,
			     BUS_AND_STATUS_REG, BASR_PHASE_MATCH, 0, HZ) < 0) {
1607
				result = -1;
1608
				shost_printk(KERN_ERR, instance, "PDMA write: DRQ and phase timeout\n");
L
Linus Torvalds 已提交
1609 1610 1611
			}
		}
	}
1612 1613

	NCR5380_dma_complete(instance);
1614
	return result;
L
Linus Torvalds 已提交
1615 1616 1617 1618 1619
}

/*
 * Function : NCR5380_information_transfer (struct Scsi_Host *instance)
 *
1620
 * Purpose : run through the various SCSI phases and do as the target
1621 1622
 * directs us to.  Operates on the currently connected command,
 * instance->connected.
L
Linus Torvalds 已提交
1623 1624 1625
 *
 * Inputs : instance, instance for which we are doing commands
 *
1626
 * Side effects : SCSI things happen, the disconnected queue will be
1627 1628
 * modified if a command disconnects, *instance->connected will
 * change.
L
Linus Torvalds 已提交
1629
 *
1630
 * XXX Note : we need to watch for bus free or a reset condition here
1631
 * to recover from an unexpected bus free condition.
L
Linus Torvalds 已提交
1632 1633
 */

1634
static void NCR5380_information_transfer(struct Scsi_Host *instance)
1635
	__releases(&hostdata->lock) __acquires(&hostdata->lock)
1636
{
F
Finn Thain 已提交
1637
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
1638 1639 1640 1641 1642 1643
	unsigned char msgout = NOP;
	int sink = 0;
	int len;
	int transfersize;
	unsigned char *data;
	unsigned char phase, tmp, extended_msg[10], old_phase = 0xff;
1644
	struct scsi_cmnd *cmd;
L
Linus Torvalds 已提交
1645

1646 1647 1648 1649
#ifdef SUN3_SCSI_VME
	dregs->csr |= CSR_INTR;
#endif

1650
	while ((cmd = hostdata->connected)) {
1651 1652
		struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);

L
Linus Torvalds 已提交
1653 1654 1655 1656 1657 1658 1659 1660
		tmp = NCR5380_read(STATUS_REG);
		/* We only have a valid SCSI phase when REQ is asserted */
		if (tmp & SR_REQ) {
			phase = (tmp & PHASE_MASK);
			if (phase != old_phase) {
				old_phase = phase;
				NCR5380_dprint_phase(NDEBUG_INFORMATION, instance);
			}
1661
#ifdef CONFIG_SUN3
1662 1663 1664
			if (phase == PHASE_CMDOUT &&
			    sun3_dma_setup_done != cmd) {
				int count;
1665 1666

				if (!cmd->SCp.this_residual && cmd->SCp.buffers_residual) {
1667 1668 1669 1670
					++cmd->SCp.buffer;
					--cmd->SCp.buffers_residual;
					cmd->SCp.this_residual = cmd->SCp.buffer->length;
					cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
1671 1672
				}

1673 1674 1675 1676 1677 1678 1679 1680 1681
				count = sun3scsi_dma_xfer_len(hostdata, cmd);

				if (count > 0) {
					if (rq_data_dir(cmd->request))
						sun3scsi_dma_send_setup(hostdata,
						                        cmd->SCp.ptr, count);
					else
						sun3scsi_dma_recv_setup(hostdata,
						                        cmd->SCp.ptr, count);
1682 1683 1684 1685 1686 1687 1688 1689
					sun3_dma_setup_done = cmd;
				}
#ifdef SUN3_SCSI_VME
				dregs->csr |= CSR_INTR;
#endif
			}
#endif /* CONFIG_SUN3 */

L
Linus Torvalds 已提交
1690 1691 1692
			if (sink && (phase != PHASE_MSGOUT)) {
				NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp));

1693 1694
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN |
				              ICR_ASSERT_ACK);
1695 1696
				while (NCR5380_read(STATUS_REG) & SR_REQ)
					;
1697 1698
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
				              ICR_ASSERT_ATN);
L
Linus Torvalds 已提交
1699 1700 1701
				sink = 0;
				continue;
			}
1702

L
Linus Torvalds 已提交
1703 1704 1705
			switch (phase) {
			case PHASE_DATAOUT:
#if (NDEBUG & NDEBUG_NO_DATAOUT)
1706
				shost_printk(KERN_DEBUG, instance, "NDEBUG_NO_DATAOUT set, attempted DATAOUT aborted\n");
L
Linus Torvalds 已提交
1707 1708 1709
				sink = 1;
				do_abort(instance);
				cmd->result = DID_ERROR << 16;
1710
				complete_cmd(instance, cmd);
F
Finn Thain 已提交
1711
				hostdata->connected = NULL;
1712
				hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun);
L
Linus Torvalds 已提交
1713 1714
				return;
#endif
F
Finn Thain 已提交
1715
			case PHASE_DATAIN:
1716
				/*
L
Linus Torvalds 已提交
1717 1718 1719 1720 1721 1722 1723 1724
				 * If there is no room left in the current buffer in the
				 * scatter-gather list, move onto the next one.
				 */

				if (!cmd->SCp.this_residual && cmd->SCp.buffers_residual) {
					++cmd->SCp.buffer;
					--cmd->SCp.buffers_residual;
					cmd->SCp.this_residual = cmd->SCp.buffer->length;
J
Jens Axboe 已提交
1725
					cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
1726 1727 1728
					dsprintk(NDEBUG_INFORMATION, instance, "%d bytes and %d buffers left\n",
					         cmd->SCp.this_residual,
					         cmd->SCp.buffers_residual);
L
Linus Torvalds 已提交
1729
				}
1730

L
Linus Torvalds 已提交
1731
				/*
1732
				 * The preferred transfer method is going to be
L
Linus Torvalds 已提交
1733 1734 1735 1736 1737 1738 1739 1740
				 * PSEUDO-DMA for systems that are strictly PIO,
				 * since we can let the hardware do the handshaking.
				 *
				 * For this to work, we need to know the transfersize
				 * ahead of time, since the pseudo-DMA code will sit
				 * in an unconditional loop.
				 */

1741
				transfersize = 0;
1742
				if (!cmd->device->borken)
1743
					transfersize = NCR5380_dma_xfer_len(hostdata, cmd);
1744

1745
				if (transfersize > 0) {
L
Linus Torvalds 已提交
1746
					len = transfersize;
1747 1748
					if (NCR5380_transfer_dma(instance, &phase,
					    &len, (unsigned char **)&cmd->SCp.ptr)) {
L
Linus Torvalds 已提交
1749
						/*
1750 1751 1752
						 * If the watchdog timer fires, all future
						 * accesses to this device will use the
						 * polled-IO.
L
Linus Torvalds 已提交
1753
						 */
J
Jeff Garzik 已提交
1754
						scmd_printk(KERN_INFO, cmd,
1755
							"switching to slow handshake\n");
L
Linus Torvalds 已提交
1756 1757 1758 1759 1760
						cmd->device->borken = 1;
						sink = 1;
						do_abort(instance);
						cmd->result = DID_ERROR << 16;
						/* XXX - need to source or sink data here, as appropriate */
1761
					}
F
Finn Thain 已提交
1762
				} else {
1763 1764
					/* Transfer a small chunk so that the
					 * irq mode lock is not held too long.
1765
					 */
1766 1767
					transfersize = min(cmd->SCp.this_residual,
							   NCR5380_PIO_CHUNK_SIZE);
1768 1769
					len = transfersize;
					NCR5380_transfer_pio(instance, &phase, &len,
1770
					                     (unsigned char **)&cmd->SCp.ptr);
1771
					cmd->SCp.this_residual -= transfersize - len;
1772
				}
1773 1774 1775 1776
#ifdef CONFIG_SUN3
				if (sun3_dma_setup_done == cmd)
					sun3_dma_setup_done = NULL;
#endif
1777
				return;
L
Linus Torvalds 已提交
1778 1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789
			case PHASE_MSGIN:
				len = 1;
				data = &tmp;
				NCR5380_transfer_pio(instance, &phase, &len, &data);
				cmd->SCp.Message = tmp;

				switch (tmp) {
				case ABORT:
				case COMMAND_COMPLETE:
					/* Accept message by clearing ACK */
					sink = 1;
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1790 1791 1792 1793
					dsprintk(NDEBUG_QUEUES, instance,
					         "COMMAND COMPLETE %p target %d lun %llu\n",
					         cmd, scmd_id(cmd), cmd->device->lun);

L
Linus Torvalds 已提交
1794
					hostdata->connected = NULL;
1795
					hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun);
L
Linus Torvalds 已提交
1796

F
Finn Thain 已提交
1797 1798 1799
					cmd->result &= ~0xffff;
					cmd->result |= cmd->SCp.Status;
					cmd->result |= cmd->SCp.Message << 8;
1800

F
Finn Thain 已提交
1801
					if (cmd->cmnd[0] == REQUEST_SENSE)
1802
						complete_cmd(instance, cmd);
F
Finn Thain 已提交
1803 1804 1805 1806 1807 1808 1809 1810 1811
					else {
						if (cmd->SCp.Status == SAM_STAT_CHECK_CONDITION ||
						    cmd->SCp.Status == SAM_STAT_COMMAND_TERMINATED) {
							dsprintk(NDEBUG_QUEUES, instance, "autosense: adding cmd %p to tail of autosense queue\n",
							         cmd);
							list_add_tail(&ncmd->list,
							              &hostdata->autosense);
						} else
							complete_cmd(instance, cmd);
L
Linus Torvalds 已提交
1812 1813
					}

1814 1815
					/*
					 * Restore phase bits to 0 so an interrupted selection,
L
Linus Torvalds 已提交
1816 1817 1818
					 * arbitration can resume.
					 */
					NCR5380_write(TARGET_COMMAND_REG, 0);
1819

1820
					maybe_release_dma_irq(instance);
L
Linus Torvalds 已提交
1821 1822 1823 1824 1825 1826 1827 1828 1829
					return;
				case MESSAGE_REJECT:
					/* Accept message by clearing ACK */
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
					switch (hostdata->last_message) {
					case HEAD_OF_QUEUE_TAG:
					case ORDERED_QUEUE_TAG:
					case SIMPLE_QUEUE_TAG:
						cmd->device->simple_tags = 0;
H
Hannes Reinecke 已提交
1830
						hostdata->busy[cmd->device->id] |= (1 << (cmd->device->lun & 0xFF));
L
Linus Torvalds 已提交
1831 1832 1833 1834
						break;
					default:
						break;
					}
1835
					break;
1836 1837 1838 1839 1840 1841 1842 1843
				case DISCONNECT:
					/* Accept message by clearing ACK */
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
					hostdata->connected = NULL;
					list_add(&ncmd->list, &hostdata->disconnected);
					dsprintk(NDEBUG_INFORMATION | NDEBUG_QUEUES,
					         instance, "connected command %p for target %d lun %llu moved to disconnected queue\n",
					         cmd, scmd_id(cmd), cmd->device->lun);
1844

1845 1846 1847 1848 1849
					/*
					 * Restore phase bits to 0 so an interrupted selection,
					 * arbitration can resume.
					 */
					NCR5380_write(TARGET_COMMAND_REG, 0);
L
Linus Torvalds 已提交
1850

1851 1852 1853
#ifdef SUN3_SCSI_VME
					dregs->csr |= CSR_DMA_ENABLE;
#endif
1854
					return;
1855
					/*
L
Linus Torvalds 已提交
1856
					 * The SCSI data pointer is *IMPLICITLY* saved on a disconnect
1857
					 * operation, in violation of the SCSI spec so we can safely
L
Linus Torvalds 已提交
1858 1859
					 * ignore SAVE/RESTORE pointers calls.
					 *
1860
					 * Unfortunately, some disks violate the SCSI spec and
L
Linus Torvalds 已提交
1861
					 * don't issue the required SAVE_POINTERS message before
1862
					 * disconnecting, and we have to break spec to remain
L
Linus Torvalds 已提交
1863 1864 1865 1866 1867 1868 1869 1870
					 * compatible.
					 */
				case SAVE_POINTERS:
				case RESTORE_POINTERS:
					/* Accept message by clearing ACK */
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
					break;
				case EXTENDED_MESSAGE:
F
Finn Thain 已提交
1871 1872 1873 1874
					/*
					 * Start the message buffer with the EXTENDED_MESSAGE
					 * byte, since spi_print_msg() wants the whole thing.
					 */
L
Linus Torvalds 已提交
1875 1876 1877
					extended_msg[0] = EXTENDED_MESSAGE;
					/* Accept first byte by clearing ACK */
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1878 1879 1880

					spin_unlock_irq(&hostdata->lock);

1881
					dsprintk(NDEBUG_EXTENDED, instance, "receiving extended message\n");
L
Linus Torvalds 已提交
1882 1883 1884 1885 1886

					len = 2;
					data = extended_msg + 1;
					phase = PHASE_MSGIN;
					NCR5380_transfer_pio(instance, &phase, &len, &data);
1887 1888 1889
					dsprintk(NDEBUG_EXTENDED, instance, "length %d, code 0x%02x\n",
					         (int)extended_msg[1],
					         (int)extended_msg[2]);
L
Linus Torvalds 已提交
1890

1891 1892
					if (!len && extended_msg[1] > 0 &&
					    extended_msg[1] <= sizeof(extended_msg) - 2) {
L
Linus Torvalds 已提交
1893 1894 1895 1896 1897 1898 1899
						/* Accept third byte by clearing ACK */
						NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
						len = extended_msg[1] - 1;
						data = extended_msg + 3;
						phase = PHASE_MSGIN;

						NCR5380_transfer_pio(instance, &phase, &len, &data);
1900 1901
						dsprintk(NDEBUG_EXTENDED, instance, "message received, residual %d\n",
						         len);
L
Linus Torvalds 已提交
1902 1903 1904 1905 1906 1907 1908

						switch (extended_msg[2]) {
						case EXTENDED_SDTR:
						case EXTENDED_WDTR:
							tmp = 0;
						}
					} else if (len) {
1909
						shost_printk(KERN_ERR, instance, "error receiving extended message\n");
L
Linus Torvalds 已提交
1910 1911
						tmp = 0;
					} else {
1912 1913
						shost_printk(KERN_NOTICE, instance, "extended message code %02x length %d is too long\n",
						             extended_msg[2], extended_msg[1]);
L
Linus Torvalds 已提交
1914 1915
						tmp = 0;
					}
1916 1917 1918 1919 1920

					spin_lock_irq(&hostdata->lock);
					if (!hostdata->connected)
						return;

L
Linus Torvalds 已提交
1921 1922
					/* Fall through to reject message */

1923 1924
					/*
					 * If we get something weird that we aren't expecting,
L
Linus Torvalds 已提交
1925 1926 1927
					 * reject it.
					 */
				default:
1928
					if (tmp == EXTENDED_MESSAGE)
J
Jeff Garzik 已提交
1929
						scmd_printk(KERN_INFO, cmd,
1930
						            "rejecting unknown extended message code %02x, length %d\n",
1931 1932 1933 1934 1935
						            extended_msg[2], extended_msg[1]);
					else if (tmp)
						scmd_printk(KERN_INFO, cmd,
						            "rejecting unknown message code %02x\n",
						            tmp);
L
Linus Torvalds 已提交
1936 1937 1938 1939

					msgout = MESSAGE_REJECT;
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
					break;
1940
				} /* switch (tmp) */
L
Linus Torvalds 已提交
1941 1942 1943 1944 1945 1946 1947 1948
				break;
			case PHASE_MSGOUT:
				len = 1;
				data = &msgout;
				hostdata->last_message = msgout;
				NCR5380_transfer_pio(instance, &phase, &len, &data);
				if (msgout == ABORT) {
					hostdata->connected = NULL;
1949
					hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun);
L
Linus Torvalds 已提交
1950
					cmd->result = DID_ERROR << 16;
1951
					complete_cmd(instance, cmd);
1952
					maybe_release_dma_irq(instance);
L
Linus Torvalds 已提交
1953 1954 1955 1956 1957 1958 1959
					return;
				}
				msgout = NOP;
				break;
			case PHASE_CMDOUT:
				len = cmd->cmd_len;
				data = cmd->cmnd;
1960 1961 1962 1963
				/*
				 * XXX for performance reasons, on machines with a
				 * PSEUDO-DMA architecture we should probably
				 * use the dma transfer function.
L
Linus Torvalds 已提交
1964 1965 1966 1967 1968 1969 1970 1971 1972 1973
				 */
				NCR5380_transfer_pio(instance, &phase, &len, &data);
				break;
			case PHASE_STATIN:
				len = 1;
				data = &tmp;
				NCR5380_transfer_pio(instance, &phase, &len, &data);
				cmd->SCp.Status = tmp;
				break;
			default:
1974
				shost_printk(KERN_ERR, instance, "unknown phase\n");
1975
				NCR5380_dprint(NDEBUG_ANY, instance);
1976
			} /* switch(phase) */
1977
		} else {
1978
			spin_unlock_irq(&hostdata->lock);
1979
			NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, HZ);
1980
			spin_lock_irq(&hostdata->lock);
L
Linus Torvalds 已提交
1981
		}
1982
	}
L
Linus Torvalds 已提交
1983 1984 1985 1986 1987
}

/*
 * Function : void NCR5380_reselect (struct Scsi_Host *instance)
 *
1988
 * Purpose : does reselection, initializing the instance->connected
1989 1990
 * field to point to the scsi_cmnd for which the I_T_L or I_T_L_Q
 * nexus has been reestablished,
1991
 *
L
Linus Torvalds 已提交
1992 1993 1994
 * Inputs : instance - this instance of the NCR5380.
 */

1995 1996
static void NCR5380_reselect(struct Scsi_Host *instance)
{
F
Finn Thain 已提交
1997
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
1998
	unsigned char target_mask;
1999
	unsigned char lun;
L
Linus Torvalds 已提交
2000
	unsigned char msg[3];
2001 2002
	struct NCR5380_cmd *ncmd;
	struct scsi_cmnd *tmp;
L
Linus Torvalds 已提交
2003 2004 2005 2006 2007 2008 2009 2010 2011

	/*
	 * Disable arbitration, etc. since the host adapter obviously
	 * lost, and tell an interrupted NCR5380_select() to restart.
	 */

	NCR5380_write(MODE_REG, MR_BASE);

	target_mask = NCR5380_read(CURRENT_SCSI_DATA_REG) & ~(hostdata->id_mask);
2012 2013 2014 2015 2016
	if (!target_mask || target_mask & (target_mask - 1)) {
		shost_printk(KERN_WARNING, instance,
			     "reselect: bad target_mask 0x%02x\n", target_mask);
		return;
	}
2017

2018
	/*
L
Linus Torvalds 已提交
2019 2020 2021 2022 2023 2024 2025 2026 2027
	 * At this point, we have detected that our SCSI ID is on the bus,
	 * SEL is true and BSY was false for at least one bus settle delay
	 * (400 ns).
	 *
	 * We must assert BSY ourselves, until the target drops the SEL
	 * signal.
	 */

	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY);
2028
	if (NCR5380_poll_politely(hostdata,
2029
	                          STATUS_REG, SR_SEL, 0, 2 * HZ) < 0) {
2030
		shost_printk(KERN_ERR, instance, "reselect: !SEL timeout\n");
2031 2032 2033
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
		return;
	}
L
Linus Torvalds 已提交
2034 2035 2036 2037 2038 2039
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

	/*
	 * Wait for target to go into MSGIN.
	 */

2040
	if (NCR5380_poll_politely(hostdata,
2041
	                          STATUS_REG, SR_REQ, SR_REQ, 2 * HZ) < 0) {
2042 2043 2044
		if ((NCR5380_read(STATUS_REG) & (SR_BSY | SR_SEL)) == 0)
			/* BUS FREE phase */
			return;
2045
		shost_printk(KERN_ERR, instance, "reselect: REQ timeout\n");
2046 2047 2048
		do_abort(instance);
		return;
	}
L
Linus Torvalds 已提交
2049

2050 2051 2052
#ifdef CONFIG_SUN3
	/* acknowledge toggle to MSGIN */
	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(PHASE_MSGIN));
L
Linus Torvalds 已提交
2053

2054 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066 2067
	/* peek at the byte without really hitting the bus */
	msg[0] = NCR5380_read(CURRENT_SCSI_DATA_REG);
#else
	{
		int len = 1;
		unsigned char *data = msg;
		unsigned char phase = PHASE_MSGIN;

		NCR5380_transfer_pio(instance, &phase, &len, &data);

		if (len) {
			do_abort(instance);
			return;
		}
2068
	}
2069
#endif /* CONFIG_SUN3 */
2070

L
Linus Torvalds 已提交
2071
	if (!(msg[0] & 0x80)) {
2072
		shost_printk(KERN_ERR, instance, "expecting IDENTIFY message, got ");
2073
		spi_print_msg(msg);
2074 2075 2076 2077 2078
		printk("\n");
		do_abort(instance);
		return;
	}
	lun = msg[0] & 0x07;
L
Linus Torvalds 已提交
2079

2080 2081 2082 2083 2084
	/*
	 * We need to add code for SCSI-II to track which devices have
	 * I_T_L_Q nexuses established, and which have simple I_T_L
	 * nexuses so we can chose to do additional data transfer.
	 */
L
Linus Torvalds 已提交
2085

2086 2087 2088 2089
	/*
	 * Find the command corresponding to the I_T_L or I_T_L_Q  nexus we
	 * just reestablished, and remove it from the disconnected queue.
	 */
L
Linus Torvalds 已提交
2090

2091 2092 2093 2094 2095 2096 2097 2098
	tmp = NULL;
	list_for_each_entry(ncmd, &hostdata->disconnected, list) {
		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);

		if (target_mask == (1 << scmd_id(cmd)) &&
		    lun == (u8)cmd->device->lun) {
			list_del(&ncmd->list);
			tmp = cmd;
2099
			break;
L
Linus Torvalds 已提交
2100 2101
		}
	}
2102 2103 2104 2105 2106

	if (tmp) {
		dsprintk(NDEBUG_RESELECTION | NDEBUG_QUEUES, instance,
		         "reselect: removed %p from disconnected queue\n", tmp);
	} else {
2107 2108
		int target = ffs(target_mask) - 1;

2109 2110 2111
		shost_printk(KERN_ERR, instance, "target bitmask 0x%02x lun %d not in disconnected queue.\n",
		             target_mask, lun);
		/*
2112 2113
		 * Since we have an established nexus that we can't do anything
		 * with, we must abort it.
2114
		 */
2115 2116
		if (do_abort(instance) == 0)
			hostdata->busy[target] &= ~(1 << lun);
2117
		return;
L
Linus Torvalds 已提交
2118
	}
2119

2120
#ifdef CONFIG_SUN3
2121 2122
	if (sun3_dma_setup_done != tmp) {
		int count;
2123 2124

		if (!tmp->SCp.this_residual && tmp->SCp.buffers_residual) {
2125 2126 2127 2128
			++tmp->SCp.buffer;
			--tmp->SCp.buffers_residual;
			tmp->SCp.this_residual = tmp->SCp.buffer->length;
			tmp->SCp.ptr = sg_virt(tmp->SCp.buffer);
2129 2130
		}

2131 2132 2133 2134 2135 2136 2137 2138 2139
		count = sun3scsi_dma_xfer_len(hostdata, tmp);

		if (count > 0) {
			if (rq_data_dir(tmp->request))
				sun3scsi_dma_send_setup(hostdata,
				                        tmp->SCp.ptr, count);
			else
				sun3scsi_dma_recv_setup(hostdata,
				                        tmp->SCp.ptr, count);
2140 2141 2142 2143 2144 2145 2146
			sun3_dma_setup_done = tmp;
		}
	}

	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK);
#endif /* CONFIG_SUN3 */

2147 2148 2149 2150
	/* Accept message by clearing ACK */
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

	hostdata->connected = tmp;
2151 2152
	dsprintk(NDEBUG_RESELECTION, instance, "nexus established, target %d, lun %llu\n",
	         scmd_id(tmp), tmp->device->lun);
L
Linus Torvalds 已提交
2153 2154
}

2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191 2192 2193 2194 2195 2196 2197 2198 2199 2200 2201 2202 2203 2204 2205 2206 2207
/**
 * list_find_cmd - test for presence of a command in a linked list
 * @haystack: list of commands
 * @needle: command to search for
 */

static bool list_find_cmd(struct list_head *haystack,
                          struct scsi_cmnd *needle)
{
	struct NCR5380_cmd *ncmd;

	list_for_each_entry(ncmd, haystack, list)
		if (NCR5380_to_scmd(ncmd) == needle)
			return true;
	return false;
}

/**
 * list_remove_cmd - remove a command from linked list
 * @haystack: list of commands
 * @needle: command to remove
 */

static bool list_del_cmd(struct list_head *haystack,
                         struct scsi_cmnd *needle)
{
	if (list_find_cmd(haystack, needle)) {
		struct NCR5380_cmd *ncmd = scsi_cmd_priv(needle);

		list_del(&ncmd->list);
		return true;
	}
	return false;
}

/**
 * NCR5380_abort - scsi host eh_abort_handler() method
 * @cmd: the command to be aborted
 *
 * Try to abort a given command by removing it from queues and/or sending
 * the target an abort message. This may not succeed in causing a target
 * to abort the command. Nonetheless, the low-level driver must forget about
 * the command because the mid-layer reclaims it and it may be re-issued.
 *
 * The normal path taken by a command is as follows. For EH we trace this
 * same path to locate and abort the command.
 *
 * unissued -> selecting -> [unissued -> selecting ->]... connected ->
 * [disconnected -> connected ->]...
 * [autosense -> connected ->] done
 *
 * If cmd was not found at all then presumably it has already been completed,
 * in which case return SUCCESS to try to avoid further EH measures.
F
Finn Thain 已提交
2208
 *
2209
 * If the command has not completed yet, we must not fail to find it.
F
Finn Thain 已提交
2210 2211 2212 2213
 * We have no option but to forget the aborted command (even if it still
 * lacks sense data). The mid-layer may re-issue a command that is in error
 * recovery (see scsi_send_eh_cmnd), but the logic and data structures in
 * this driver are such that a command can appear on one queue only.
2214 2215 2216
 *
 * The lock protects driver data structures, but EH handlers also use it
 * to serialize their own execution and prevent their own re-entry.
L
Linus Torvalds 已提交
2217 2218
 */

F
Finn Thain 已提交
2219 2220
static int NCR5380_abort(struct scsi_cmnd *cmd)
{
L
Linus Torvalds 已提交
2221
	struct Scsi_Host *instance = cmd->device->host;
F
Finn Thain 已提交
2222
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
2223
	unsigned long flags;
2224
	int result = SUCCESS;
2225

2226 2227
	spin_lock_irqsave(&hostdata->lock, flags);

2228
#if (NDEBUG & NDEBUG_ANY)
2229
	scmd_printk(KERN_INFO, cmd, __func__);
2230
#endif
2231 2232
	NCR5380_dprint(NDEBUG_ANY, instance);
	NCR5380_dprint_phase(NDEBUG_ANY, instance);
L
Linus Torvalds 已提交
2233

2234 2235 2236 2237 2238
	if (list_del_cmd(&hostdata->unissued, cmd)) {
		dsprintk(NDEBUG_ABORT, instance,
		         "abort: removed %p from issue queue\n", cmd);
		cmd->result = DID_ABORT << 16;
		cmd->scsi_done(cmd); /* No tag or busy flag to worry about */
F
Finn Thain 已提交
2239
		goto out;
2240 2241
	}

2242 2243 2244 2245 2246 2247 2248 2249 2250
	if (hostdata->selecting == cmd) {
		dsprintk(NDEBUG_ABORT, instance,
		         "abort: cmd %p == selecting\n", cmd);
		hostdata->selecting = NULL;
		cmd->result = DID_ABORT << 16;
		complete_cmd(instance, cmd);
		goto out;
	}

2251 2252 2253
	if (list_del_cmd(&hostdata->disconnected, cmd)) {
		dsprintk(NDEBUG_ABORT, instance,
		         "abort: removed %p from disconnected list\n", cmd);
2254 2255 2256
		/* Can't call NCR5380_select() and send ABORT because that
		 * means releasing the lock. Need a bus reset.
		 */
F
Finn Thain 已提交
2257 2258
		set_host_byte(cmd, DID_ERROR);
		complete_cmd(instance, cmd);
2259 2260
		result = FAILED;
		goto out;
2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273
	}

	if (hostdata->connected == cmd) {
		dsprintk(NDEBUG_ABORT, instance, "abort: cmd %p is connected\n", cmd);
		hostdata->connected = NULL;
		hostdata->dma_len = 0;
		if (do_abort(instance)) {
			set_host_byte(cmd, DID_ERROR);
			complete_cmd(instance, cmd);
			result = FAILED;
			goto out;
		}
		set_host_byte(cmd, DID_ABORT);
F
Finn Thain 已提交
2274 2275 2276 2277 2278 2279 2280
		complete_cmd(instance, cmd);
		goto out;
	}

	if (list_del_cmd(&hostdata->autosense, cmd)) {
		dsprintk(NDEBUG_ABORT, instance,
		         "abort: removed %p from sense queue\n", cmd);
2281 2282 2283 2284 2285 2286
		complete_cmd(instance, cmd);
	}

out:
	if (result == FAILED)
		dsprintk(NDEBUG_ABORT, instance, "abort: failed to abort %p\n", cmd);
2287 2288
	else {
		hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun);
2289
		dsprintk(NDEBUG_ABORT, instance, "abort: successfully aborted %p\n", cmd);
2290
	}
2291 2292

	queue_work(hostdata->work_q, &hostdata->main_task);
2293
	maybe_release_dma_irq(instance);
2294
	spin_unlock_irqrestore(&hostdata->lock, flags);
2295

2296
	return result;
L
Linus Torvalds 已提交
2297 2298 2299
}


2300
/**
2301
 * NCR5380_host_reset - reset the SCSI host
2302
 * @cmd: SCSI command undergoing EH
L
Linus Torvalds 已提交
2303
 *
2304
 * Returns SUCCESS
L
Linus Torvalds 已提交
2305 2306
 */

2307
static int NCR5380_host_reset(struct scsi_cmnd *cmd)
2308 2309
{
	struct Scsi_Host *instance = cmd->device->host;
2310
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
2311
	int i;
2312
	unsigned long flags;
2313
	struct NCR5380_cmd *ncmd;
2314

2315
	spin_lock_irqsave(&hostdata->lock, flags);
2316 2317

#if (NDEBUG & NDEBUG_ANY)
2318
	shost_printk(KERN_INFO, instance, __func__);
2319
#endif
2320 2321
	NCR5380_dprint(NDEBUG_ANY, instance);
	NCR5380_dprint_phase(NDEBUG_ANY, instance);
2322 2323

	do_reset(instance);
2324

2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335
	/* reset NCR registers */
	NCR5380_write(MODE_REG, MR_BASE);
	NCR5380_write(TARGET_COMMAND_REG, 0);
	NCR5380_write(SELECT_ENABLE_REG, 0);

	/* After the reset, there are no more connected or disconnected commands
	 * and no busy units; so clear the low-level status here to avoid
	 * conflicts when the mid-level code tries to wake up the affected
	 * commands!
	 */

2336 2337 2338
	list_for_each_entry(ncmd, &hostdata->unissued, list) {
		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);

2339 2340 2341
		cmd->result = DID_RESET << 16;
		cmd->scsi_done(cmd);
	}
2342
	INIT_LIST_HEAD(&hostdata->unissued);
2343 2344 2345 2346 2347 2348

	if (hostdata->selecting) {
		hostdata->selecting->result = DID_RESET << 16;
		complete_cmd(instance, hostdata->selecting);
		hostdata->selecting = NULL;
	}
2349 2350 2351 2352 2353

	list_for_each_entry(ncmd, &hostdata->disconnected, list) {
		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);

		set_host_byte(cmd, DID_RESET);
2354
		complete_cmd(instance, cmd);
2355
	}
2356
	INIT_LIST_HEAD(&hostdata->disconnected);
2357 2358 2359 2360 2361 2362

	list_for_each_entry(ncmd, &hostdata->autosense, list) {
		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);

		cmd->scsi_done(cmd);
	}
2363
	INIT_LIST_HEAD(&hostdata->autosense);
2364 2365 2366 2367 2368 2369 2370 2371 2372 2373 2374 2375

	if (hostdata->connected) {
		set_host_byte(hostdata->connected, DID_RESET);
		complete_cmd(instance, hostdata->connected);
		hostdata->connected = NULL;
	}

	for (i = 0; i < 8; ++i)
		hostdata->busy[i] = 0;
	hostdata->dma_len = 0;

	queue_work(hostdata->work_q, &hostdata->main_task);
2376
	maybe_release_dma_irq(instance);
2377
	spin_unlock_irqrestore(&hostdata->lock, flags);
L
Linus Torvalds 已提交
2378 2379 2380

	return SUCCESS;
}