NCR5380.c 72.0 KB
Newer Older
1
/*
L
Linus Torvalds 已提交
2
 * NCR 5380 generic driver routines.  These should make it *trivial*
3 4
 * to implement 5380 SCSI drivers under Linux with a non-trantor
 * architecture.
L
Linus Torvalds 已提交
5
 *
6
 * Note that these routines also work with NR53c400 family chips.
L
Linus Torvalds 已提交
7 8
 *
 * Copyright 1993, Drew Eckhardt
9 10 11 12
 * Visionary Computing
 * (Unix and Linux consulting and custom programming)
 * drew@colorado.edu
 * +1 (303) 666-5836
L
Linus Torvalds 已提交
13
 *
14
 * For more information, please consult
L
Linus Torvalds 已提交
15 16 17 18 19 20 21 22 23 24 25 26 27
 *
 * NCR 5380 Family
 * SCSI Protocol Controller
 * Databook
 *
 * NCR Microelectronics
 * 1635 Aeroplaza Drive
 * Colorado Springs, CO 80916
 * 1+ (719) 578-3400
 * 1+ (800) 334-5454
 */

/*
F
Finn Thain 已提交
28 29
 * With contributions from Ray Van Tassle, Ingmar Baumgart,
 * Ronald van Cuijlenborg, Alan Cox and others.
L
Linus Torvalds 已提交
30 31
 */

32 33
/* Ported to Atari by Roman Hodek and others. */

34 35
/* Adapted for the Sun 3 by Sam Creasey. */

L
Linus Torvalds 已提交
36 37 38
/*
 * Design
 *
39
 * This is a generic 5380 driver.  To use it on a different platform,
L
Linus Torvalds 已提交
40
 * one simply writes appropriate system specific macros (ie, data
41
 * transfer - some PC's will use the I/O bus, 68K's must use
L
Linus Torvalds 已提交
42 43
 * memory mapped) and drops this file in their 'C' wrapper.
 *
44
 * As far as command queueing, two queues are maintained for
L
Linus Torvalds 已提交
45
 * each 5380 in the system - commands that haven't been issued yet,
46 47 48 49 50
 * and commands that are currently executing.  This means that an
 * unlimited number of commands may be queued, letting
 * more commands propagate from the higher driver levels giving higher
 * throughput.  Note that both I_T_L and I_T_L_Q nexuses are supported,
 * allowing multiple commands to propagate all the way to a SCSI-II device
L
Linus Torvalds 已提交
51 52 53
 * while a command is already executing.
 *
 *
54
 * Issues specific to the NCR5380 :
L
Linus Torvalds 已提交
55
 *
56 57 58 59
 * When used in a PIO or pseudo-dma mode, the NCR5380 is a braindead
 * piece of hardware that requires you to sit in a loop polling for
 * the REQ signal as long as you are connected.  Some devices are
 * brain dead (ie, many TEXEL CD ROM drives) and won't disconnect
60
 * while doing long seek operations. [...] These
L
Linus Torvalds 已提交
61 62 63 64 65 66 67 68 69
 * broken devices are the exception rather than the rule and I'd rather
 * spend my time optimizing for the normal case.
 *
 * Architecture :
 *
 * At the heart of the design is a coroutine, NCR5380_main,
 * which is started from a workqueue for each NCR5380 host in the
 * system.  It attempts to establish I_T_L or I_T_L_Q nexuses by
 * removing the commands from the issue queue and calling
70
 * NCR5380_select() if a nexus is not established.
L
Linus Torvalds 已提交
71 72 73 74 75
 *
 * Once a nexus is established, the NCR5380_information_transfer()
 * phase goes through the various phases as instructed by the target.
 * if the target goes into MSG IN and sends a DISCONNECT message,
 * the command structure is placed into the per instance disconnected
76
 * queue, and NCR5380_main tries to find more work.  If the target is
L
Linus Torvalds 已提交
77 78 79 80 81 82
 * idle for too long, the system will try to sleep.
 *
 * If a command has disconnected, eventually an interrupt will trigger,
 * calling NCR5380_intr()  which will in turn call NCR5380_reselect
 * to reestablish a nexus.  This will run main if necessary.
 *
83
 * On command termination, the done function will be called as
L
Linus Torvalds 已提交
84 85
 * appropriate.
 *
86
 * SCSI pointers are maintained in the SCp field of SCSI command
L
Linus Torvalds 已提交
87 88 89 90 91 92 93 94 95
 * structures, being initialized after the command is connected
 * in NCR5380_select, and set as appropriate in NCR5380_information_transfer.
 * Note that in violation of the standard, an implicit SAVE POINTERS operation
 * is done, since some BROKEN disks fail to issue an explicit SAVE POINTERS.
 */

/*
 * Using this file :
 * This file a skeleton Linux SCSI driver for the NCR 5380 series
96
 * of chips.  To use it, you write an architecture specific functions
L
Linus Torvalds 已提交
97 98
 * and macros and include this file in your driver.
 *
99 100
 * These macros control options :
 * AUTOPROBE_IRQ - if defined, the NCR5380_probe_irq() function will be
101
 * defined.
102
 *
L
Linus Torvalds 已提交
103
 * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
104
 * for commands that return with a CHECK CONDITION status.
L
Linus Torvalds 已提交
105 106
 *
 * DIFFERENTIAL - if defined, NCR53c81 chips will use external differential
107
 * transceivers.
L
Linus Torvalds 已提交
108 109 110
 *
 * PSEUDO_DMA - if defined, PSEUDO DMA is used during the data transfer phases.
 *
111 112
 * REAL_DMA - if defined, REAL DMA is used during the data transfer phases.
 *
L
Linus Torvalds 已提交
113
 * These macros MUST be defined :
114
 *
L
Linus Torvalds 已提交
115 116
 * NCR5380_read(register)  - read from the specified register
 *
117
 * NCR5380_write(register, value) - write to the specific register
L
Linus Torvalds 已提交
118
 *
119
 * NCR5380_implementation_fields  - additional fields needed for this
120
 * specific implementation of the NCR5380
L
Linus Torvalds 已提交
121 122 123 124 125 126 127 128
 *
 * Either real DMA *or* pseudo DMA may be implemented
 *
 * NCR5380_dma_write_setup(instance, src, count) - initialize
 * NCR5380_dma_read_setup(instance, dst, count) - initialize
 * NCR5380_dma_residual(instance); - residual count
 *
 * The generic driver is initialized by calling NCR5380_init(instance),
129
 * after setting the appropriate host specific fields and ID.  If the
L
Linus Torvalds 已提交
130 131 132 133
 * driver wishes to autoprobe for an IRQ line, the NCR5380_probe_irq(instance,
 * possible) function may be used.
 */

134 135 136 137
#ifndef NCR5380_io_delay
#define NCR5380_io_delay(x)
#endif

138 139 140 141 142 143 144 145
#ifndef NCR5380_acquire_dma_irq
#define NCR5380_acquire_dma_irq(x)	(1)
#endif

#ifndef NCR5380_release_dma_irq
#define NCR5380_release_dma_irq(x)
#endif

146 147
static int do_abort(struct Scsi_Host *);
static void do_reset(struct Scsi_Host *);
L
Linus Torvalds 已提交
148

F
Finn Thain 已提交
149
/**
150
 * initialize_SCp - init the scsi pointer field
151
 * @cmd: command block to set up
L
Linus Torvalds 已提交
152
 *
153
 * Set up the internal fields in the SCSI command.
L
Linus Torvalds 已提交
154 155
 */

F
Finn Thain 已提交
156
static inline void initialize_SCp(struct scsi_cmnd *cmd)
L
Linus Torvalds 已提交
157
{
158 159
	/*
	 * Initialize the Scsi Pointer field so that all of the commands in the
L
Linus Torvalds 已提交
160 161 162
	 * various queues are valid.
	 */

163 164 165
	if (scsi_bufflen(cmd)) {
		cmd->SCp.buffer = scsi_sglist(cmd);
		cmd->SCp.buffers_residual = scsi_sg_count(cmd) - 1;
J
Jens Axboe 已提交
166
		cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
L
Linus Torvalds 已提交
167 168 169 170
		cmd->SCp.this_residual = cmd->SCp.buffer->length;
	} else {
		cmd->SCp.buffer = NULL;
		cmd->SCp.buffers_residual = 0;
171 172
		cmd->SCp.ptr = NULL;
		cmd->SCp.this_residual = 0;
L
Linus Torvalds 已提交
173
	}
F
Finn Thain 已提交
174 175 176

	cmd->SCp.Status = 0;
	cmd->SCp.Message = 0;
L
Linus Torvalds 已提交
177 178 179
}

/**
180
 * NCR5380_poll_politely2 - wait for two chip register values
181
 * @hostdata: host private data
182 183 184 185 186 187
 * @reg1: 5380 register to poll
 * @bit1: Bitmask to check
 * @val1: Expected value
 * @reg2: Second 5380 register to poll
 * @bit2: Second bitmask to check
 * @val2: Second expected value
188 189 190 191 192 193 194
 * @wait: Time-out in jiffies
 *
 * Polls the chip in a reasonably efficient manner waiting for an
 * event to occur. After a short quick poll we begin to yield the CPU
 * (if possible). In irq contexts the time-out is arbitrarily limited.
 * Callers may hold locks as long as they are held in irq mode.
 *
195
 * Returns 0 if either or both event(s) occurred otherwise -ETIMEDOUT.
L
Linus Torvalds 已提交
196
 */
197

198
static int NCR5380_poll_politely2(struct NCR5380_hostdata *hostdata,
199 200 201
                                  unsigned int reg1, u8 bit1, u8 val1,
                                  unsigned int reg2, u8 bit2, u8 val2,
                                  unsigned long wait)
L
Linus Torvalds 已提交
202
{
203
	unsigned long n = hostdata->poll_loops;
204 205 206
	unsigned long deadline = jiffies + wait;

	do {
207 208 209
		if ((NCR5380_read(reg1) & bit1) == val1)
			return 0;
		if ((NCR5380_read(reg2) & bit2) == val2)
L
Linus Torvalds 已提交
210 211
			return 0;
		cpu_relax();
212 213 214 215 216 217 218 219
	} while (n--);

	if (irqs_disabled() || in_interrupt())
		return -ETIMEDOUT;

	/* Repeatedly sleep for 1 ms until deadline */
	while (time_is_after_jiffies(deadline)) {
		schedule_timeout_uninterruptible(1);
220 221 222
		if ((NCR5380_read(reg1) & bit1) == val1)
			return 0;
		if ((NCR5380_read(reg2) & bit2) == val2)
L
Linus Torvalds 已提交
223 224
			return 0;
	}
225

L
Linus Torvalds 已提交
226 227 228
	return -ETIMEDOUT;
}

229
#if NDEBUG
L
Linus Torvalds 已提交
230 231 232
static struct {
	unsigned char mask;
	const char *name;
233 234 235 236 237 238 239 240 241
} signals[] = {
	{SR_DBP, "PARITY"},
	{SR_RST, "RST"},
	{SR_BSY, "BSY"},
	{SR_REQ, "REQ"},
	{SR_MSG, "MSG"},
	{SR_CD, "CD"},
	{SR_IO, "IO"},
	{SR_SEL, "SEL"},
L
Linus Torvalds 已提交
242
	{0, NULL}
243
},
L
Linus Torvalds 已提交
244
basrs[] = {
245 246 247 248 249 250
	{BASR_END_DMA_TRANSFER, "END OF DMA"},
	{BASR_DRQ, "DRQ"},
	{BASR_PARITY_ERROR, "PARITY ERROR"},
	{BASR_IRQ, "IRQ"},
	{BASR_PHASE_MATCH, "PHASE MATCH"},
	{BASR_BUSY_ERROR, "BUSY ERROR"},
251 252
	{BASR_ATN, "ATN"},
	{BASR_ACK, "ACK"},
L
Linus Torvalds 已提交
253
	{0, NULL}
254 255 256
},
icrs[] = {
	{ICR_ASSERT_RST, "ASSERT RST"},
257 258
	{ICR_ARBITRATION_PROGRESS, "ARB. IN PROGRESS"},
	{ICR_ARBITRATION_LOST, "LOST ARB."},
259 260 261 262 263
	{ICR_ASSERT_ACK, "ASSERT ACK"},
	{ICR_ASSERT_BSY, "ASSERT BSY"},
	{ICR_ASSERT_SEL, "ASSERT SEL"},
	{ICR_ASSERT_ATN, "ASSERT ATN"},
	{ICR_ASSERT_DATA, "ASSERT DATA"},
L
Linus Torvalds 已提交
264
	{0, NULL}
265 266
},
mrs[] = {
267 268 269 270 271 272 273 274
	{MR_BLOCK_DMA_MODE, "BLOCK DMA MODE"},
	{MR_TARGET, "TARGET"},
	{MR_ENABLE_PAR_CHECK, "PARITY CHECK"},
	{MR_ENABLE_PAR_INTR, "PARITY INTR"},
	{MR_ENABLE_EOP_INTR, "EOP INTR"},
	{MR_MONITOR_BSY, "MONITOR BSY"},
	{MR_DMA_MODE, "DMA MODE"},
	{MR_ARBITRATE, "ARBITRATE"},
L
Linus Torvalds 已提交
275 276 277 278
	{0, NULL}
};

/**
279 280
 * NCR5380_print - print scsi bus signals
 * @instance: adapter state to dump
L
Linus Torvalds 已提交
281
 *
282
 * Print the SCSI bus signals for debugging purposes
L
Linus Torvalds 已提交
283 284 285 286
 */

static void NCR5380_print(struct Scsi_Host *instance)
{
287
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
288 289 290 291 292 293 294 295
	unsigned char status, data, basr, mr, icr, i;

	data = NCR5380_read(CURRENT_SCSI_DATA_REG);
	status = NCR5380_read(STATUS_REG);
	mr = NCR5380_read(MODE_REG);
	icr = NCR5380_read(INITIATOR_COMMAND_REG);
	basr = NCR5380_read(BUS_AND_STATUS_REG);

296
	printk(KERN_DEBUG "SR =   0x%02x : ", status);
L
Linus Torvalds 已提交
297 298
	for (i = 0; signals[i].mask; ++i)
		if (status & signals[i].mask)
299 300
			printk(KERN_CONT "%s, ", signals[i].name);
	printk(KERN_CONT "\nBASR = 0x%02x : ", basr);
L
Linus Torvalds 已提交
301 302
	for (i = 0; basrs[i].mask; ++i)
		if (basr & basrs[i].mask)
303 304
			printk(KERN_CONT "%s, ", basrs[i].name);
	printk(KERN_CONT "\nICR =  0x%02x : ", icr);
L
Linus Torvalds 已提交
305 306
	for (i = 0; icrs[i].mask; ++i)
		if (icr & icrs[i].mask)
307 308
			printk(KERN_CONT "%s, ", icrs[i].name);
	printk(KERN_CONT "\nMR =   0x%02x : ", mr);
L
Linus Torvalds 已提交
309 310
	for (i = 0; mrs[i].mask; ++i)
		if (mr & mrs[i].mask)
311 312
			printk(KERN_CONT "%s, ", mrs[i].name);
	printk(KERN_CONT "\n");
L
Linus Torvalds 已提交
313 314
}

315 316 317 318 319 320 321 322 323 324 325 326
static struct {
	unsigned char value;
	const char *name;
} phases[] = {
	{PHASE_DATAOUT, "DATAOUT"},
	{PHASE_DATAIN, "DATAIN"},
	{PHASE_CMDOUT, "CMDOUT"},
	{PHASE_STATIN, "STATIN"},
	{PHASE_MSGOUT, "MSGOUT"},
	{PHASE_MSGIN, "MSGIN"},
	{PHASE_UNKNOWN, "UNKNOWN"}
};
L
Linus Torvalds 已提交
327

F
Finn Thain 已提交
328
/**
329
 * NCR5380_print_phase - show SCSI phase
330
 * @instance: adapter to dump
L
Linus Torvalds 已提交
331
 *
332
 * Print the current SCSI phase for debugging purposes
L
Linus Torvalds 已提交
333 334 335 336
 */

static void NCR5380_print_phase(struct Scsi_Host *instance)
{
337
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
338 339 340 341 342
	unsigned char status;
	int i;

	status = NCR5380_read(STATUS_REG);
	if (!(status & SR_REQ))
343
		shost_printk(KERN_DEBUG, instance, "REQ not asserted, phase unknown.\n");
L
Linus Torvalds 已提交
344
	else {
345 346 347
		for (i = 0; (phases[i].value != PHASE_UNKNOWN) &&
		     (phases[i].value != (status & PHASE_MASK)); ++i)
			;
348
		shost_printk(KERN_DEBUG, instance, "phase %s\n", phases[i].name);
L
Linus Torvalds 已提交
349 350 351 352 353
	}
}
#endif


354
static int probe_irq;
L
Linus Torvalds 已提交
355 356

/**
357 358 359 360
 * probe_intr	-	helper for IRQ autoprobe
 * @irq: interrupt number
 * @dev_id: unused
 * @regs: unused
L
Linus Torvalds 已提交
361
 *
362 363
 * Set a flag to indicate the IRQ in question was received. This is
 * used by the IRQ probe code.
L
Linus Torvalds 已提交
364
 */
365

366
static irqreturn_t probe_intr(int irq, void *dev_id)
L
Linus Torvalds 已提交
367 368 369 370 371 372
{
	probe_irq = irq;
	return IRQ_HANDLED;
}

/**
373 374 375
 * NCR5380_probe_irq	-	find the IRQ of an NCR5380
 * @instance: NCR5380 controller
 * @possible: bitmask of ISA IRQ lines
L
Linus Torvalds 已提交
376
 *
377 378
 * Autoprobe for the IRQ line used by the NCR5380 by triggering an IRQ
 * and then looking to see what interrupt actually turned up.
L
Linus Torvalds 已提交
379 380
 */

381
static int __maybe_unused NCR5380_probe_irq(struct Scsi_Host *instance,
A
Andrew Morton 已提交
382
						int possible)
L
Linus Torvalds 已提交
383
{
F
Finn Thain 已提交
384
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
385 386 387
	unsigned long timeout;
	int trying_irqs, i, mask;

F
Finn Thain 已提交
388
	for (trying_irqs = 0, i = 1, mask = 2; i < 16; ++i, mask <<= 1)
389
		if ((mask & possible) && (request_irq(i, &probe_intr, 0, "NCR-probe", NULL) == 0))
L
Linus Torvalds 已提交
390 391
			trying_irqs |= mask;

392
	timeout = jiffies + msecs_to_jiffies(250);
F
Finn Thain 已提交
393
	probe_irq = NO_IRQ;
L
Linus Torvalds 已提交
394 395 396

	/*
	 * A interrupt is triggered whenever BSY = false, SEL = true
397
	 * and a bit set in the SELECT_ENABLE_REG is asserted on the
L
Linus Torvalds 已提交
398 399 400 401 402 403 404 405 406 407 408 409
	 * SCSI bus.
	 *
	 * Note that the bus is only driven when the phase control signals
	 * (I/O, C/D, and MSG) match those in the TCR, so we must reset that
	 * to zero.
	 */

	NCR5380_write(TARGET_COMMAND_REG, 0);
	NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
	NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA | ICR_ASSERT_SEL);

F
Finn Thain 已提交
410
	while (probe_irq == NO_IRQ && time_before(jiffies, timeout))
411
		schedule_timeout_uninterruptible(1);
412

L
Linus Torvalds 已提交
413 414 415
	NCR5380_write(SELECT_ENABLE_REG, 0);
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

F
Finn Thain 已提交
416
	for (i = 1, mask = 2; i < 16; ++i, mask <<= 1)
L
Linus Torvalds 已提交
417 418 419 420 421 422 423
		if (trying_irqs & mask)
			free_irq(i, NULL);

	return probe_irq;
}

/**
424 425
 * NCR58380_info - report driver and host information
 * @instance: relevant scsi host instance
L
Linus Torvalds 已提交
426
 *
427
 * For use as the host template info() handler.
L
Linus Torvalds 已提交
428 429
 */

F
Finn Thain 已提交
430
static const char *NCR5380_info(struct Scsi_Host *instance)
L
Linus Torvalds 已提交
431
{
F
Finn Thain 已提交
432 433 434 435 436 437 438 439 440 441
	struct NCR5380_hostdata *hostdata = shost_priv(instance);

	return hostdata->info;
}

static void prepare_info(struct Scsi_Host *instance)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);

	snprintf(hostdata->info, sizeof(hostdata->info),
442 443
	         "%s, irq %d, "
		 "io_port 0x%lx, base 0x%lx, "
F
Finn Thain 已提交
444 445
	         "can_queue %d, cmd_per_lun %d, "
	         "sg_tablesize %d, this_id %d, "
446
	         "flags { %s%s%s}, "
F
Finn Thain 已提交
447
	         "options { %s} ",
448 449
	         instance->hostt->name, instance->irq,
		 hostdata->io_port, hostdata->base,
F
Finn Thain 已提交
450 451
	         instance->can_queue, instance->cmd_per_lun,
	         instance->sg_tablesize, instance->this_id,
452
	         hostdata->flags & FLAG_DMA_FIXUP     ? "DMA_FIXUP "     : "",
F
Finn Thain 已提交
453
	         hostdata->flags & FLAG_NO_PSEUDO_DMA ? "NO_PSEUDO_DMA " : "",
454
	         hostdata->flags & FLAG_TOSHIBA_DELAY ? "TOSHIBA_DELAY "  : "",
L
Linus Torvalds 已提交
455
#ifdef DIFFERENTIAL
F
Finn Thain 已提交
456
	         "DIFFERENTIAL "
L
Linus Torvalds 已提交
457 458
#endif
#ifdef PARITY
F
Finn Thain 已提交
459 460 461
	         "PARITY "
#endif
	         "");
L
Linus Torvalds 已提交
462 463 464
}

/**
465
 * NCR5380_init - initialise an NCR5380
466 467
 * @instance: adapter to configure
 * @flags: control flags
L
Linus Torvalds 已提交
468
 *
469 470
 * Initializes *instance and corresponding 5380 chip,
 * with flags OR'd into the initial flags value.
L
Linus Torvalds 已提交
471
 *
472
 * Notes : I assume that the host, hostno, and id bits have been
473
 * set correctly. I don't care about the irq and other fields.
L
Linus Torvalds 已提交
474
 *
475
 * Returns 0 for success
L
Linus Torvalds 已提交
476 477
 */

478
static int NCR5380_init(struct Scsi_Host *instance, int flags)
L
Linus Torvalds 已提交
479
{
F
Finn Thain 已提交
480
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
481
	int i;
482
	unsigned long deadline;
483
	unsigned long accesses_per_ms;
L
Linus Torvalds 已提交
484

F
Finn Thain 已提交
485 486
	instance->max_lun = 7;

487
	hostdata->host = instance;
L
Linus Torvalds 已提交
488
	hostdata->id_mask = 1 << instance->this_id;
489
	hostdata->id_higher_mask = 0;
L
Linus Torvalds 已提交
490 491 492 493 494
	for (i = hostdata->id_mask; i <= 0x80; i <<= 1)
		if (i > hostdata->id_mask)
			hostdata->id_higher_mask |= i;
	for (i = 0; i < 8; ++i)
		hostdata->busy[i] = 0;
495 496
	hostdata->dma_len = 0;

497
	spin_lock_init(&hostdata->lock);
L
Linus Torvalds 已提交
498
	hostdata->connected = NULL;
F
Finn Thain 已提交
499 500
	hostdata->sensing = NULL;
	INIT_LIST_HEAD(&hostdata->autosense);
501 502 503
	INIT_LIST_HEAD(&hostdata->unissued);
	INIT_LIST_HEAD(&hostdata->disconnected);

504
	hostdata->flags = flags;
505

506
	INIT_WORK(&hostdata->main_task, NCR5380_main);
507 508 509 510 511 512
	hostdata->work_q = alloc_workqueue("ncr5380_%d",
	                        WQ_UNBOUND | WQ_MEM_RECLAIM,
	                        1, instance->host_no);
	if (!hostdata->work_q)
		return -ENOMEM;

F
Finn Thain 已提交
513 514
	prepare_info(instance);

L
Linus Torvalds 已提交
515 516 517 518
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
	NCR5380_write(MODE_REG, MR_BASE);
	NCR5380_write(TARGET_COMMAND_REG, 0);
	NCR5380_write(SELECT_ENABLE_REG, 0);
519 520 521 522 523 524 525 526 527 528 529 530 531

	/* Calibrate register polling loop */
	i = 0;
	deadline = jiffies + 1;
	do {
		cpu_relax();
	} while (time_is_after_jiffies(deadline));
	deadline += msecs_to_jiffies(256);
	do {
		NCR5380_read(STATUS_REG);
		++i;
		cpu_relax();
	} while (time_is_after_jiffies(deadline));
532 533
	accesses_per_ms = i / 256;
	hostdata->poll_loops = NCR5380_REG_POLL_TIME * accesses_per_ms / 2;
534

535 536
	return 0;
}
L
Linus Torvalds 已提交
537

538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553
/**
 * NCR5380_maybe_reset_bus - Detect and correct bus wedge problems.
 * @instance: adapter to check
 *
 * If the system crashed, it may have crashed with a connected target and
 * the SCSI bus busy. Check for BUS FREE phase. If not, try to abort the
 * currently established nexus, which we know nothing about. Failing that
 * do a bus reset.
 *
 * Note that a bus reset will cause the chip to assert IRQ.
 *
 * Returns 0 if successful, otherwise -ENXIO.
 */

static int NCR5380_maybe_reset_bus(struct Scsi_Host *instance)
{
554
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
555
	int pass;
L
Linus Torvalds 已提交
556 557 558 559 560 561

	for (pass = 1; (NCR5380_read(STATUS_REG) & SR_BSY) && pass <= 6; ++pass) {
		switch (pass) {
		case 1:
		case 3:
		case 5:
562
			shost_printk(KERN_ERR, instance, "SCSI bus busy, waiting up to five seconds\n");
563
			NCR5380_poll_politely(hostdata,
564
			                      STATUS_REG, SR_BSY, 0, 5 * HZ);
L
Linus Torvalds 已提交
565 566
			break;
		case 2:
567
			shost_printk(KERN_ERR, instance, "bus busy, attempting abort\n");
L
Linus Torvalds 已提交
568 569 570
			do_abort(instance);
			break;
		case 4:
571
			shost_printk(KERN_ERR, instance, "bus busy, attempting reset\n");
L
Linus Torvalds 已提交
572
			do_reset(instance);
573 574 575 576 577 578 579 580
			/* Wait after a reset; the SCSI standard calls for
			 * 250ms, we wait 500ms to be on the safe side.
			 * But some Toshiba CD-ROMs need ten times that.
			 */
			if (hostdata->flags & FLAG_TOSHIBA_DELAY)
				msleep(2500);
			else
				msleep(500);
L
Linus Torvalds 已提交
581 582
			break;
		case 6:
583
			shost_printk(KERN_ERR, instance, "bus locked solid\n");
L
Linus Torvalds 已提交
584 585 586 587 588 589 590
			return -ENXIO;
		}
	}
	return 0;
}

/**
591
 * NCR5380_exit - remove an NCR5380
592
 * @instance: adapter to remove
593 594
 *
 * Assumes that no more work can be queued (e.g. by NCR5380_intr).
L
Linus Torvalds 已提交
595 596
 */

597
static void NCR5380_exit(struct Scsi_Host *instance)
L
Linus Torvalds 已提交
598
{
F
Finn Thain 已提交
599
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
600

601
	cancel_work_sync(&hostdata->main_task);
602
	destroy_workqueue(hostdata->work_q);
L
Linus Torvalds 已提交
603 604
}

605 606 607 608 609 610 611 612 613 614 615 616 617
/**
 * complete_cmd - finish processing a command and return it to the SCSI ML
 * @instance: the host instance
 * @cmd: command to complete
 */

static void complete_cmd(struct Scsi_Host *instance,
                         struct scsi_cmnd *cmd)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);

	dsprintk(NDEBUG_QUEUES, instance, "complete_cmd: cmd %p\n", cmd);

F
Finn Thain 已提交
618 619 620 621 622 623 624 625 626 627
	if (hostdata->sensing == cmd) {
		/* Autosense processing ends here */
		if ((cmd->result & 0xff) != SAM_STAT_GOOD) {
			scsi_eh_restore_cmnd(cmd, &hostdata->ses);
			set_host_byte(cmd, DID_ERROR);
		} else
			scsi_eh_restore_cmnd(cmd, &hostdata->ses);
		hostdata->sensing = NULL;
	}

628 629 630 631 632
	hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun);

	cmd->scsi_done(cmd);
}

L
Linus Torvalds 已提交
633
/**
F
Finn Thain 已提交
634 635 636
 * NCR5380_queue_command - queue a command
 * @instance: the relevant SCSI adapter
 * @cmd: SCSI command
L
Linus Torvalds 已提交
637
 *
F
Finn Thain 已提交
638 639 640
 * cmd is added to the per-instance issue queue, with minor
 * twiddling done to the host specific fields of cmd.  If the
 * main coroutine is not running, it is restarted.
L
Linus Torvalds 已提交
641 642
 */

F
Finn Thain 已提交
643 644
static int NCR5380_queue_command(struct Scsi_Host *instance,
                                 struct scsi_cmnd *cmd)
L
Linus Torvalds 已提交
645
{
F
Finn Thain 已提交
646
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
647
	struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
F
Finn Thain 已提交
648
	unsigned long flags;
L
Linus Torvalds 已提交
649 650 651 652 653

#if (NDEBUG & NDEBUG_NO_WRITE)
	switch (cmd->cmnd[0]) {
	case WRITE_6:
	case WRITE_10:
654
		shost_printk(KERN_DEBUG, instance, "WRITE attempted with NDEBUG_NO_WRITE set\n");
L
Linus Torvalds 已提交
655
		cmd->result = (DID_ERROR << 16);
F
Finn Thain 已提交
656
		cmd->scsi_done(cmd);
L
Linus Torvalds 已提交
657 658
		return 0;
	}
659
#endif /* (NDEBUG & NDEBUG_NO_WRITE) */
L
Linus Torvalds 已提交
660 661 662

	cmd->result = 0;

663 664 665
	if (!NCR5380_acquire_dma_irq(instance))
		return SCSI_MLQUEUE_HOST_BUSY;

666
	spin_lock_irqsave(&hostdata->lock, flags);
F
Finn Thain 已提交
667

668 669
	/*
	 * Insert the cmd into the issue queue. Note that REQUEST SENSE
L
Linus Torvalds 已提交
670
	 * commands are added to the head of the queue since any command will
671
	 * clear the contingent allegiance condition that exists and the
L
Linus Torvalds 已提交
672 673 674
	 * sense data is only guaranteed to be valid while the condition exists.
	 */

675 676 677 678 679
	if (cmd->cmnd[0] == REQUEST_SENSE)
		list_add(&ncmd->list, &hostdata->unissued);
	else
		list_add_tail(&ncmd->list, &hostdata->unissued);

680
	spin_unlock_irqrestore(&hostdata->lock, flags);
F
Finn Thain 已提交
681

682 683
	dsprintk(NDEBUG_QUEUES, instance, "command %p added to %s of queue\n",
	         cmd, (cmd->cmnd[0] == REQUEST_SENSE) ? "head" : "tail");
L
Linus Torvalds 已提交
684 685

	/* Kick off command processing */
686
	queue_work(hostdata->work_q, &hostdata->main_task);
L
Linus Torvalds 已提交
687 688 689
	return 0;
}

690 691 692 693 694 695 696 697 698 699 700 701 702
static inline void maybe_release_dma_irq(struct Scsi_Host *instance)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);

	/* Caller does the locking needed to set & test these data atomically */
	if (list_empty(&hostdata->disconnected) &&
	    list_empty(&hostdata->unissued) &&
	    list_empty(&hostdata->autosense) &&
	    !hostdata->connected &&
	    !hostdata->selecting)
		NCR5380_release_dma_irq(instance);
}

F
Finn Thain 已提交
703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719
/**
 * dequeue_next_cmd - dequeue a command for processing
 * @instance: the scsi host instance
 *
 * Priority is given to commands on the autosense queue. These commands
 * need autosense because of a CHECK CONDITION result.
 *
 * Returns a command pointer if a command is found for a target that is
 * not already busy. Otherwise returns NULL.
 */

static struct scsi_cmnd *dequeue_next_cmd(struct Scsi_Host *instance)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
	struct NCR5380_cmd *ncmd;
	struct scsi_cmnd *cmd;

720
	if (hostdata->sensing || list_empty(&hostdata->autosense)) {
F
Finn Thain 已提交
721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752
		list_for_each_entry(ncmd, &hostdata->unissued, list) {
			cmd = NCR5380_to_scmd(ncmd);
			dsprintk(NDEBUG_QUEUES, instance, "dequeue: cmd=%p target=%d busy=0x%02x lun=%llu\n",
			         cmd, scmd_id(cmd), hostdata->busy[scmd_id(cmd)], cmd->device->lun);

			if (!(hostdata->busy[scmd_id(cmd)] & (1 << cmd->device->lun))) {
				list_del(&ncmd->list);
				dsprintk(NDEBUG_QUEUES, instance,
				         "dequeue: removed %p from issue queue\n", cmd);
				return cmd;
			}
		}
	} else {
		/* Autosense processing begins here */
		ncmd = list_first_entry(&hostdata->autosense,
		                        struct NCR5380_cmd, list);
		list_del(&ncmd->list);
		cmd = NCR5380_to_scmd(ncmd);
		dsprintk(NDEBUG_QUEUES, instance,
		         "dequeue: removed %p from autosense queue\n", cmd);
		scsi_eh_prep_cmnd(cmd, &hostdata->ses, NULL, 0, ~0);
		hostdata->sensing = cmd;
		return cmd;
	}
	return NULL;
}

static void requeue_cmd(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
	struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);

753
	if (hostdata->sensing == cmd) {
F
Finn Thain 已提交
754 755 756 757 758 759 760
		scsi_eh_restore_cmnd(cmd, &hostdata->ses);
		list_add(&ncmd->list, &hostdata->autosense);
		hostdata->sensing = NULL;
	} else
		list_add(&ncmd->list, &hostdata->unissued);
}

L
Linus Torvalds 已提交
761
/**
762
 * NCR5380_main - NCR state machines
L
Linus Torvalds 已提交
763
 *
764 765 766 767
 * NCR5380_main is a coroutine that runs as long as more work can
 * be done on the NCR5380 host adapters in a system.  Both
 * NCR5380_queue_command() and NCR5380_intr() will try to start it
 * in case it is not running.
L
Linus Torvalds 已提交
768 769
 */

D
David Howells 已提交
770
static void NCR5380_main(struct work_struct *work)
L
Linus Torvalds 已提交
771
{
D
David Howells 已提交
772
	struct NCR5380_hostdata *hostdata =
773
		container_of(work, struct NCR5380_hostdata, main_task);
L
Linus Torvalds 已提交
774 775
	struct Scsi_Host *instance = hostdata->host;
	int done;
776

L
Linus Torvalds 已提交
777 778
	do {
		done = 1;
779

F
Finn Thain 已提交
780
		spin_lock_irq(&hostdata->lock);
781 782 783 784 785
		while (!hostdata->connected && !hostdata->selecting) {
			struct scsi_cmnd *cmd = dequeue_next_cmd(instance);

			if (!cmd)
				break;
L
Linus Torvalds 已提交
786

F
Finn Thain 已提交
787
			dsprintk(NDEBUG_MAIN, instance, "main: dequeued %p\n", cmd);
788

F
Finn Thain 已提交
789 790 791 792 793 794 795 796 797 798 799 800
			/*
			 * Attempt to establish an I_T_L nexus here.
			 * On success, instance->hostdata->connected is set.
			 * On failure, we must add the command back to the
			 * issue queue so we can keep trying.
			 */
			/*
			 * REQUEST SENSE commands are issued without tagged
			 * queueing, even on SCSI-II devices because the
			 * contingent allegiance condition exists for the
			 * entire unit.
			 */
801

802
			if (!NCR5380_select(instance, cmd)) {
803
				dsprintk(NDEBUG_MAIN, instance, "main: select complete\n");
804
				maybe_release_dma_irq(instance);
F
Finn Thain 已提交
805 806 807 808 809 810
			} else {
				dsprintk(NDEBUG_MAIN | NDEBUG_QUEUES, instance,
				         "main: select failed, returning %p to queue\n", cmd);
				requeue_cmd(instance, cmd);
			}
		}
811
		if (hostdata->connected && !hostdata->dma_len) {
812
			dsprintk(NDEBUG_MAIN, instance, "main: performing information transfer\n");
L
Linus Torvalds 已提交
813 814
			NCR5380_information_transfer(instance);
			done = 0;
815
		}
F
Finn Thain 已提交
816 817 818
		spin_unlock_irq(&hostdata->lock);
		if (!done)
			cond_resched();
L
Linus Torvalds 已提交
819 820 821
	} while (!done);
}

822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852
/*
 * NCR5380_dma_complete - finish DMA transfer
 * @instance: the scsi host instance
 *
 * Called by the interrupt handler when DMA finishes or a phase
 * mismatch occurs (which would end the DMA transfer).
 */

static void NCR5380_dma_complete(struct Scsi_Host *instance)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
	int transferred;
	unsigned char **data;
	int *count;
	int saved_data = 0, overrun = 0;
	unsigned char p;

	if (hostdata->read_overruns) {
		p = hostdata->connected->SCp.phase;
		if (p & SR_IO) {
			udelay(10);
			if ((NCR5380_read(BUS_AND_STATUS_REG) &
			     (BASR_PHASE_MATCH | BASR_ACK)) ==
			    (BASR_PHASE_MATCH | BASR_ACK)) {
				saved_data = NCR5380_read(INPUT_DATA_REG);
				overrun = 1;
				dsprintk(NDEBUG_DMA, instance, "read overrun handled\n");
			}
		}
	}

853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869
#ifdef CONFIG_SUN3
	if ((sun3scsi_dma_finish(rq_data_dir(hostdata->connected->request)))) {
		pr_err("scsi%d: overrun in UDC counter -- not prepared to deal with this!\n",
		       instance->host_no);
		BUG();
	}

	if ((NCR5380_read(BUS_AND_STATUS_REG) & (BASR_PHASE_MATCH | BASR_ACK)) ==
	    (BASR_PHASE_MATCH | BASR_ACK)) {
		pr_err("scsi%d: BASR %02x\n", instance->host_no,
		       NCR5380_read(BUS_AND_STATUS_REG));
		pr_err("scsi%d: bus stuck in data phase -- probably a single byte overrun!\n",
		       instance->host_no);
		BUG();
	}
#endif

870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904
	NCR5380_write(MODE_REG, MR_BASE);
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
	NCR5380_read(RESET_PARITY_INTERRUPT_REG);

	transferred = hostdata->dma_len - NCR5380_dma_residual(instance);
	hostdata->dma_len = 0;

	data = (unsigned char **)&hostdata->connected->SCp.ptr;
	count = &hostdata->connected->SCp.this_residual;
	*data += transferred;
	*count -= transferred;

	if (hostdata->read_overruns) {
		int cnt, toPIO;

		if ((NCR5380_read(STATUS_REG) & PHASE_MASK) == p && (p & SR_IO)) {
			cnt = toPIO = hostdata->read_overruns;
			if (overrun) {
				dsprintk(NDEBUG_DMA, instance,
				         "Got an input overrun, using saved byte\n");
				*(*data)++ = saved_data;
				(*count)--;
				cnt--;
				toPIO--;
			}
			if (toPIO > 0) {
				dsprintk(NDEBUG_DMA, instance,
				         "Doing %d byte PIO to 0x%p\n", cnt, *data);
				NCR5380_transfer_pio(instance, &p, &cnt, data);
				*count -= toPIO - cnt;
			}
		}
	}
}

L
Linus Torvalds 已提交
905
/**
906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936
 * NCR5380_intr - generic NCR5380 irq handler
 * @irq: interrupt number
 * @dev_id: device info
 *
 * Handle interrupts, reestablishing I_T_L or I_T_L_Q nexuses
 * from the disconnected queue, and restarting NCR5380_main()
 * as required.
 *
 * The chip can assert IRQ in any of six different conditions. The IRQ flag
 * is then cleared by reading the Reset Parity/Interrupt Register (RPIR).
 * Three of these six conditions are latched in the Bus and Status Register:
 * - End of DMA (cleared by ending DMA Mode)
 * - Parity error (cleared by reading RPIR)
 * - Loss of BSY (cleared by reading RPIR)
 * Two conditions have flag bits that are not latched:
 * - Bus phase mismatch (non-maskable in DMA Mode, cleared by ending DMA Mode)
 * - Bus reset (non-maskable)
 * The remaining condition has no flag bit at all:
 * - Selection/reselection
 *
 * Hence, establishing the cause(s) of any interrupt is partly guesswork.
 * In "The DP8490 and DP5380 Comparison Guide", National Semiconductor
 * claimed that "the design of the [DP8490] interrupt logic ensures
 * interrupts will not be lost (they can be on the DP5380)."
 * The L5380/53C80 datasheet from LOGIC Devices has more details.
 *
 * Checking for bus reset by reading RST is futile because of interrupt
 * latency, but a bus reset will reset chip logic. Checking for parity error
 * is unnecessary because that interrupt is never enabled. A Loss of BSY
 * condition will clear DMA Mode. We can tell when this occurs because the
 * the Busy Monitor interrupt is enabled together with DMA Mode.
L
Linus Torvalds 已提交
937 938
 */

939
static irqreturn_t __maybe_unused NCR5380_intr(int irq, void *dev_id)
L
Linus Torvalds 已提交
940
{
941
	struct Scsi_Host *instance = dev_id;
942 943
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
	int handled = 0;
L
Linus Torvalds 已提交
944 945 946
	unsigned char basr;
	unsigned long flags;

947
	spin_lock_irqsave(&hostdata->lock, flags);
948 949 950 951 952 953

	basr = NCR5380_read(BUS_AND_STATUS_REG);
	if (basr & BASR_IRQ) {
		unsigned char mr = NCR5380_read(MODE_REG);
		unsigned char sr = NCR5380_read(STATUS_REG);

954 955
		dsprintk(NDEBUG_INTR, instance, "IRQ %d, BASR 0x%02x, SR 0x%02x, MR 0x%02x\n",
		         irq, basr, sr, mr);
L
Linus Torvalds 已提交
956

957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972
		if ((mr & MR_DMA_MODE) || (mr & MR_MONITOR_BSY)) {
			/* Probably End of DMA, Phase Mismatch or Loss of BSY.
			 * We ack IRQ after clearing Mode Register. Workarounds
			 * for End of DMA errata need to happen in DMA Mode.
			 */

			dsprintk(NDEBUG_INTR, instance, "interrupt in DMA mode\n");

			if (hostdata->connected) {
				NCR5380_dma_complete(instance);
				queue_work(hostdata->work_q, &hostdata->main_task);
			} else {
				NCR5380_write(MODE_REG, MR_BASE);
				NCR5380_read(RESET_PARITY_INTERRUPT_REG);
			}
		} else if ((NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_mask) &&
973 974 975 976 977
		    (sr & (SR_SEL | SR_IO | SR_BSY | SR_RST)) == (SR_SEL | SR_IO)) {
			/* Probably reselected */
			NCR5380_write(SELECT_ENABLE_REG, 0);
			NCR5380_read(RESET_PARITY_INTERRUPT_REG);

978
			dsprintk(NDEBUG_INTR, instance, "interrupt with SEL and IO\n");
979 980 981 982

			if (!hostdata->connected) {
				NCR5380_reselect(instance);
				queue_work(hostdata->work_q, &hostdata->main_task);
L
Linus Torvalds 已提交
983
			}
984 985 986 987 988 989
			if (!hostdata->connected)
				NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
		} else {
			/* Probably Bus Reset */
			NCR5380_read(RESET_PARITY_INTERRUPT_REG);

990
			dsprintk(NDEBUG_INTR, instance, "unknown interrupt\n");
991 992 993
#ifdef SUN3_SCSI_VME
			dregs->csr |= CSR_DMA_ENABLE;
#endif
994 995 996 997
		}
		handled = 1;
	} else {
		shost_printk(KERN_NOTICE, instance, "interrupt without IRQ bit\n");
998 999 1000
#ifdef SUN3_SCSI_VME
		dregs->csr |= CSR_DMA_ENABLE;
#endif
1001 1002
	}

1003
	spin_unlock_irqrestore(&hostdata->lock, flags);
1004 1005

	return IRQ_RETVAL(handled);
L
Linus Torvalds 已提交
1006 1007
}

1008
/*
F
Finn Thain 已提交
1009
 * Function : int NCR5380_select(struct Scsi_Host *instance,
1010
 * struct scsi_cmnd *cmd)
L
Linus Torvalds 已提交
1011 1012
 *
 * Purpose : establishes I_T_L or I_T_L_Q nexus for new or existing command,
1013 1014
 * including ARBITRATION, SELECTION, and initial message out for
 * IDENTIFY and queue messages.
L
Linus Torvalds 已提交
1015
 *
1016
 * Inputs : instance - instantiation of the 5380 driver on which this
1017
 * target lives, cmd - SCSI command to execute.
1018
 *
1019 1020 1021
 * Returns cmd if selection failed but should be retried,
 * NULL if selection failed and should not be retried, or
 * NULL if selection succeeded (hostdata->connected == cmd).
L
Linus Torvalds 已提交
1022
 *
1023
 * Side effects :
1024 1025 1026 1027
 * If bus busy, arbitration failed, etc, NCR5380_select() will exit
 * with registers as they should have been on entry - ie
 * SELECT_ENABLE will be set appropriately, the NCR5380
 * will cease to drive any SCSI bus signals.
L
Linus Torvalds 已提交
1028
 *
1029 1030 1031
 * If successful : I_T_L or I_T_L_Q nexus will be established,
 * instance->connected will be set to cmd.
 * SELECT interrupt will be disabled.
L
Linus Torvalds 已提交
1032
 *
1033 1034
 * If failed (no target) : cmd->scsi_done() will be called, and the
 * cmd->result host byte set to DID_BAD_TARGET.
L
Linus Torvalds 已提交
1035
 */
1036

1037 1038
static struct scsi_cmnd *NCR5380_select(struct Scsi_Host *instance,
                                        struct scsi_cmnd *cmd)
L
Linus Torvalds 已提交
1039
{
F
Finn Thain 已提交
1040
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
1041 1042 1043 1044 1045 1046
	unsigned char tmp[3], phase;
	unsigned char *data;
	int len;
	int err;

	NCR5380_dprint(NDEBUG_ARBITRATION, instance);
1047 1048
	dsprintk(NDEBUG_ARBITRATION, instance, "starting arbitration, id = %d\n",
	         instance->this_id);
L
Linus Torvalds 已提交
1049

1050 1051 1052 1053 1054 1055 1056 1057 1058
	/*
	 * Arbitration and selection phases are slow and involve dropping the
	 * lock, so we have to watch out for EH. An exception handler may
	 * change 'selecting' to NULL. This function will then return NULL
	 * so that the caller will forget about 'cmd'. (During information
	 * transfer phases, EH may change 'connected' to NULL.)
	 */
	hostdata->selecting = cmd;

1059 1060
	/*
	 * Set the phase bits to 0, otherwise the NCR5380 won't drive the
L
Linus Torvalds 已提交
1061 1062 1063 1064 1065
	 * data bus during SELECTION.
	 */

	NCR5380_write(TARGET_COMMAND_REG, 0);

1066
	/*
L
Linus Torvalds 已提交
1067 1068 1069 1070 1071 1072
	 * Start arbitration.
	 */

	NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
	NCR5380_write(MODE_REG, MR_ARBITRATE);

1073 1074 1075
	/* The chip now waits for BUS FREE phase. Then after the 800 ns
	 * Bus Free Delay, arbitration will begin.
	 */
L
Linus Torvalds 已提交
1076

1077
	spin_unlock_irq(&hostdata->lock);
1078
	err = NCR5380_poll_politely2(hostdata, MODE_REG, MR_ARBITRATE, 0,
1079 1080
	                INITIATOR_COMMAND_REG, ICR_ARBITRATION_PROGRESS,
	                                       ICR_ARBITRATION_PROGRESS, HZ);
1081
	spin_lock_irq(&hostdata->lock);
1082 1083
	if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE)) {
		/* Reselection interrupt */
1084
		goto out;
1085
	}
1086 1087 1088 1089 1090
	if (!hostdata->selecting) {
		/* Command was aborted */
		NCR5380_write(MODE_REG, MR_BASE);
		goto out;
	}
1091 1092 1093 1094
	if (err < 0) {
		NCR5380_write(MODE_REG, MR_BASE);
		shost_printk(KERN_ERR, instance,
		             "select: arbitration timeout\n");
1095
		goto out;
L
Linus Torvalds 已提交
1096
	}
1097
	spin_unlock_irq(&hostdata->lock);
L
Linus Torvalds 已提交
1098

1099
	/* The SCSI-2 arbitration delay is 2.4 us */
L
Linus Torvalds 已提交
1100 1101 1102
	udelay(3);

	/* Check for lost arbitration */
1103 1104 1105
	if ((NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST) ||
	    (NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_higher_mask) ||
	    (NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST)) {
L
Linus Torvalds 已提交
1106
		NCR5380_write(MODE_REG, MR_BASE);
1107
		dsprintk(NDEBUG_ARBITRATION, instance, "lost arbitration, deasserting MR_ARBITRATE\n");
1108
		spin_lock_irq(&hostdata->lock);
1109
		goto out;
L
Linus Torvalds 已提交
1110
	}
1111 1112 1113 1114 1115 1116 1117

	/* After/during arbitration, BSY should be asserted.
	 * IBM DPES-31080 Version S31Q works now
	 * Tnx to Thomas_Roesch@m2.maus.de for finding this! (Roman)
	 */
	NCR5380_write(INITIATOR_COMMAND_REG,
		      ICR_BASE | ICR_ASSERT_SEL | ICR_ASSERT_BSY);
L
Linus Torvalds 已提交
1118

1119 1120
	/*
	 * Again, bus clear + bus settle time is 1.2us, however, this is
L
Linus Torvalds 已提交
1121 1122 1123
	 * a minimum so we'll udelay ceil(1.2)
	 */

1124 1125 1126 1127
	if (hostdata->flags & FLAG_TOSHIBA_DELAY)
		udelay(15);
	else
		udelay(2);
L
Linus Torvalds 已提交
1128

1129 1130
	spin_lock_irq(&hostdata->lock);

1131 1132
	/* NCR5380_reselect() clears MODE_REG after a reselection interrupt */
	if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE))
1133 1134 1135 1136 1137 1138 1139
		goto out;

	if (!hostdata->selecting) {
		NCR5380_write(MODE_REG, MR_BASE);
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
		goto out;
	}
1140

1141
	dsprintk(NDEBUG_ARBITRATION, instance, "won arbitration\n");
L
Linus Torvalds 已提交
1142

1143 1144
	/*
	 * Now that we have won arbitration, start Selection process, asserting
L
Linus Torvalds 已提交
1145 1146 1147
	 * the host and target ID's on the SCSI bus.
	 */

1148
	NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask | (1 << scmd_id(cmd)));
L
Linus Torvalds 已提交
1149

1150
	/*
L
Linus Torvalds 已提交
1151 1152 1153 1154 1155
	 * Raise ATN while SEL is true before BSY goes false from arbitration,
	 * since this is the only way to guarantee that we'll get a MESSAGE OUT
	 * phase immediately after selection.
	 */

1156 1157
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY |
	              ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_SEL);
L
Linus Torvalds 已提交
1158 1159
	NCR5380_write(MODE_REG, MR_BASE);

1160
	/*
L
Linus Torvalds 已提交
1161 1162 1163 1164 1165
	 * Reselect interrupts must be turned off prior to the dropping of BSY,
	 * otherwise we will trigger an interrupt.
	 */
	NCR5380_write(SELECT_ENABLE_REG, 0);

1166 1167
	spin_unlock_irq(&hostdata->lock);

L
Linus Torvalds 已提交
1168
	/*
1169
	 * The initiator shall then wait at least two deskew delays and release
L
Linus Torvalds 已提交
1170 1171
	 * the BSY signal.
	 */
1172
	udelay(1);        /* wingel -- wait two bus deskew delay >2*45ns */
L
Linus Torvalds 已提交
1173 1174

	/* Reset BSY */
1175 1176
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA |
	              ICR_ASSERT_ATN | ICR_ASSERT_SEL);
L
Linus Torvalds 已提交
1177

1178
	/*
L
Linus Torvalds 已提交
1179
	 * Something weird happens when we cease to drive BSY - looks
1180
	 * like the board/chip is letting us do another read before the
L
Linus Torvalds 已提交
1181 1182 1183 1184 1185
	 * appropriate propagation delay has expired, and we're confusing
	 * a BSY signal from ourselves as the target's response to SELECTION.
	 *
	 * A small delay (the 'C++' frontend breaks the pipeline with an
	 * unnecessary jump, making it work on my 386-33/Trantor T128, the
1186 1187 1188
	 * tighter 'C' code breaks and requires this) solves the problem -
	 * the 1 us delay is arbitrary, and only used because this delay will
	 * be the same on other platforms and since it works here, it should
L
Linus Torvalds 已提交
1189 1190 1191 1192 1193 1194 1195 1196
	 * work there.
	 *
	 * wingel suggests that this could be due to failing to wait
	 * one deskew delay.
	 */

	udelay(1);

1197
	dsprintk(NDEBUG_SELECTION, instance, "selecting target %d\n", scmd_id(cmd));
L
Linus Torvalds 已提交
1198

1199 1200
	/*
	 * The SCSI specification calls for a 250 ms timeout for the actual
L
Linus Torvalds 已提交
1201 1202 1203
	 * selection.
	 */

1204
	err = NCR5380_poll_politely(hostdata, STATUS_REG, SR_BSY, SR_BSY,
F
Finn Thain 已提交
1205
	                            msecs_to_jiffies(250));
L
Linus Torvalds 已提交
1206 1207

	if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
1208
		spin_lock_irq(&hostdata->lock);
L
Linus Torvalds 已提交
1209 1210
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
		NCR5380_reselect(instance);
1211 1212
		if (!hostdata->connected)
			NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
1213
		shost_printk(KERN_ERR, instance, "reselection after won arbitration?\n");
1214
		goto out;
L
Linus Torvalds 已提交
1215
	}
F
Finn Thain 已提交
1216 1217

	if (err < 0) {
1218
		spin_lock_irq(&hostdata->lock);
F
Finn Thain 已提交
1219 1220
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
		NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
1221 1222 1223 1224 1225 1226 1227 1228
		/* Can't touch cmd if it has been reclaimed by the scsi ML */
		if (hostdata->selecting) {
			cmd->result = DID_BAD_TARGET << 16;
			complete_cmd(instance, cmd);
			dsprintk(NDEBUG_SELECTION, instance, "target did not respond within 250ms\n");
			cmd = NULL;
		}
		goto out;
F
Finn Thain 已提交
1229 1230
	}

1231 1232 1233
	/*
	 * No less than two deskew delays after the initiator detects the
	 * BSY signal is true, it shall release the SEL signal and may
L
Linus Torvalds 已提交
1234 1235 1236 1237 1238 1239 1240 1241
	 * change the DATA BUS.                                     -wingel
	 */

	udelay(1);

	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);

	/*
1242
	 * Since we followed the SCSI spec, and raised ATN while SEL
L
Linus Torvalds 已提交
1243 1244 1245 1246 1247 1248 1249
	 * was true but before BSY was false during selection, the information
	 * transfer phase should be a MESSAGE OUT phase so that we can send the
	 * IDENTIFY message.
	 */

	/* Wait for start of REQ/ACK handshake */

1250
	err = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, HZ);
1251
	spin_lock_irq(&hostdata->lock);
1252
	if (err < 0) {
1253 1254
		shost_printk(KERN_ERR, instance, "select: REQ timeout\n");
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
L
Linus Torvalds 已提交
1255
		NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
1256 1257 1258 1259 1260
		goto out;
	}
	if (!hostdata->selecting) {
		do_abort(instance);
		goto out;
L
Linus Torvalds 已提交
1261 1262
	}

1263 1264
	dsprintk(NDEBUG_SELECTION, instance, "target %d selected, going into MESSAGE OUT phase.\n",
	         scmd_id(cmd));
F
Finn Thain 已提交
1265
	tmp[0] = IDENTIFY(((instance->irq == NO_IRQ) ? 0 : 1), cmd->device->lun);
L
Linus Torvalds 已提交
1266 1267 1268 1269 1270

	len = 1;
	data = tmp;
	phase = PHASE_MSGOUT;
	NCR5380_transfer_pio(instance, &phase, &len, &data);
1271
	dsprintk(NDEBUG_SELECTION, instance, "nexus established.\n");
L
Linus Torvalds 已提交
1272
	/* XXX need to handle errors here */
1273

L
Linus Torvalds 已提交
1274
	hostdata->connected = cmd;
1275
	hostdata->busy[cmd->device->id] |= 1 << cmd->device->lun;
L
Linus Torvalds 已提交
1276

1277 1278 1279 1280
#ifdef SUN3_SCSI_VME
	dregs->csr |= CSR_INTR;
#endif

1281
	initialize_SCp(cmd);
L
Linus Torvalds 已提交
1282

1283 1284 1285 1286 1287 1288 1289
	cmd = NULL;

out:
	if (!hostdata->selecting)
		return NULL;
	hostdata->selecting = NULL;
	return cmd;
L
Linus Torvalds 已提交
1290 1291
}

1292 1293
/*
 * Function : int NCR5380_transfer_pio (struct Scsi_Host *instance,
1294
 * unsigned char *phase, int *count, unsigned char **data)
L
Linus Torvalds 已提交
1295 1296 1297
 *
 * Purpose : transfers data in given phase using polled I/O
 *
1298
 * Inputs : instance - instance of driver, *phase - pointer to
1299 1300
 * what phase is expected, *count - pointer to number of
 * bytes to transfer, **data - pointer to data pointer.
1301
 *
L
Linus Torvalds 已提交
1302
 * Returns : -1 when different phase is entered without transferring
1303
 * maximum number of bytes, 0 if all bytes are transferred or exit
1304
 * is in same phase.
L
Linus Torvalds 已提交
1305
 *
1306
 * Also, *phase, *count, *data are modified in place.
L
Linus Torvalds 已提交
1307 1308 1309 1310 1311
 *
 * XXX Note : handling for bus free may be useful.
 */

/*
1312
 * Note : this code is not as quick as it could be, however it
L
Linus Torvalds 已提交
1313 1314 1315 1316
 * IS 100% reliable, and for the actual data transfer where speed
 * counts, we will always do a pseudo DMA or DMA transfer.
 */

1317 1318 1319 1320
static int NCR5380_transfer_pio(struct Scsi_Host *instance,
				unsigned char *phase, int *count,
				unsigned char **data)
{
1321
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
1322 1323 1324 1325
	unsigned char p = *phase, tmp;
	int c = *count;
	unsigned char *d = *data;

1326 1327
	/*
	 * The NCR5380 chip will only drive the SCSI bus when the
L
Linus Torvalds 已提交
1328 1329 1330 1331
	 * phase specified in the appropriate bits of the TARGET COMMAND
	 * REGISTER match the STATUS REGISTER
	 */

1332
	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
L
Linus Torvalds 已提交
1333 1334

	do {
1335 1336 1337
		/*
		 * Wait for assertion of REQ, after which the phase bits will be
		 * valid
L
Linus Torvalds 已提交
1338 1339
		 */

1340
		if (NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, HZ) < 0)
L
Linus Torvalds 已提交
1341 1342
			break;

1343
		dsprintk(NDEBUG_HANDSHAKE, instance, "REQ asserted\n");
L
Linus Torvalds 已提交
1344 1345

		/* Check for phase mismatch */
1346
		if ((NCR5380_read(STATUS_REG) & PHASE_MASK) != p) {
1347 1348
			dsprintk(NDEBUG_PIO, instance, "phase mismatch\n");
			NCR5380_dprint_phase(NDEBUG_PIO, instance);
L
Linus Torvalds 已提交
1349 1350
			break;
		}
1351

L
Linus Torvalds 已提交
1352 1353 1354 1355 1356 1357 1358 1359
		/* Do actual transfer from SCSI bus to / from memory */
		if (!(p & SR_IO))
			NCR5380_write(OUTPUT_DATA_REG, *d);
		else
			*d = NCR5380_read(CURRENT_SCSI_DATA_REG);

		++d;

1360
		/*
L
Linus Torvalds 已提交
1361 1362 1363 1364 1365 1366 1367 1368 1369 1370
		 * The SCSI standard suggests that in MSGOUT phase, the initiator
		 * should drop ATN on the last byte of the message phase
		 * after REQ has been asserted for the handshake but before
		 * the initiator raises ACK.
		 */

		if (!(p & SR_IO)) {
			if (!((p & SR_MSG) && c > 1)) {
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA);
				NCR5380_dprint(NDEBUG_PIO, instance);
1371 1372
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
				              ICR_ASSERT_DATA | ICR_ASSERT_ACK);
L
Linus Torvalds 已提交
1373
			} else {
1374 1375
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
				              ICR_ASSERT_DATA | ICR_ASSERT_ATN);
L
Linus Torvalds 已提交
1376
				NCR5380_dprint(NDEBUG_PIO, instance);
1377 1378
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
				              ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_ACK);
L
Linus Torvalds 已提交
1379 1380 1381 1382 1383 1384
			}
		} else {
			NCR5380_dprint(NDEBUG_PIO, instance);
			NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK);
		}

1385
		if (NCR5380_poll_politely(hostdata,
1386 1387 1388
		                          STATUS_REG, SR_REQ, 0, 5 * HZ) < 0)
			break;

1389
		dsprintk(NDEBUG_HANDSHAKE, instance, "REQ negated, handshake complete\n");
L
Linus Torvalds 已提交
1390 1391

/*
1392 1393
 * We have several special cases to consider during REQ/ACK handshaking :
 * 1.  We were in MSGOUT phase, and we are on the last byte of the
1394
 * message.  ATN must be dropped as ACK is dropped.
L
Linus Torvalds 已提交
1395
 *
1396
 * 2.  We are in a MSGIN phase, and we are on the last byte of the
1397 1398
 * message.  We must exit with ACK asserted, so that the calling
 * code may raise ATN before dropping ACK to reject the message.
L
Linus Torvalds 已提交
1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409
 *
 * 3.  ACK and ATN are clear and the target may proceed as normal.
 */
		if (!(p == PHASE_MSGIN && c == 1)) {
			if (p == PHASE_MSGOUT && c > 1)
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
			else
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
		}
	} while (--c);

1410
	dsprintk(NDEBUG_PIO, instance, "residual %d\n", c);
L
Linus Torvalds 已提交
1411 1412 1413 1414

	*count = c;
	*data = d;
	tmp = NCR5380_read(STATUS_REG);
1415 1416 1417 1418 1419
	/* The phase read from the bus is valid if either REQ is (already)
	 * asserted or if ACK hasn't been released yet. The latter applies if
	 * we're in MSG IN, DATA IN or STATUS and all bytes have been received.
	 */
	if ((tmp & SR_REQ) || ((tmp & SR_IO) && c == 0))
L
Linus Torvalds 已提交
1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430
		*phase = tmp & PHASE_MASK;
	else
		*phase = PHASE_UNKNOWN;

	if (!c || (*phase == p))
		return 0;
	else
		return -1;
}

/**
1431 1432
 * do_reset - issue a reset command
 * @instance: adapter to reset
L
Linus Torvalds 已提交
1433
 *
1434 1435
 * Issue a reset sequence to the NCR5380 and try and get the bus
 * back into sane shape.
L
Linus Torvalds 已提交
1436
 *
1437 1438 1439
 * This clears the reset interrupt flag because there may be no handler for
 * it. When the driver is initialized, the NCR5380_intr() handler has not yet
 * been installed. And when in EH we may have released the ST DMA interrupt.
L
Linus Torvalds 已提交
1440
 */
1441

1442 1443
static void do_reset(struct Scsi_Host *instance)
{
1444
	struct NCR5380_hostdata __maybe_unused *hostdata = shost_priv(instance);
1445 1446 1447 1448 1449
	unsigned long flags;

	local_irq_save(flags);
	NCR5380_write(TARGET_COMMAND_REG,
	              PHASE_SR_TO_TCR(NCR5380_read(STATUS_REG) & PHASE_MASK));
L
Linus Torvalds 已提交
1450
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST);
1451
	udelay(50);
L
Linus Torvalds 已提交
1452
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1453 1454
	(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
	local_irq_restore(flags);
L
Linus Torvalds 已提交
1455 1456
}

1457 1458 1459 1460
/**
 * do_abort - abort the currently established nexus by going to
 * MESSAGE OUT phase and sending an ABORT message.
 * @instance: relevant scsi host instance
L
Linus Torvalds 已提交
1461
 *
1462
 * Returns 0 on success, -1 on failure.
L
Linus Torvalds 已提交
1463 1464
 */

1465 1466
static int do_abort(struct Scsi_Host *instance)
{
1467
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
1468 1469 1470 1471 1472 1473 1474
	unsigned char *msgptr, phase, tmp;
	int len;
	int rc;

	/* Request message out phase */
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);

1475 1476 1477 1478
	/*
	 * Wait for the target to indicate a valid phase by asserting
	 * REQ.  Once this happens, we'll have either a MSGOUT phase
	 * and can immediately send the ABORT message, or we'll have some
L
Linus Torvalds 已提交
1479
	 * other phase and will have to source/sink data.
1480
	 *
L
Linus Torvalds 已提交
1481 1482 1483 1484
	 * We really don't care what value was on the bus or what value
	 * the target sees, so we just handshake.
	 */

1485
	rc = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, 10 * HZ);
1486
	if (rc < 0)
1487
		goto timeout;
L
Linus Torvalds 已提交
1488

1489
	tmp = NCR5380_read(STATUS_REG) & PHASE_MASK;
1490

L
Linus Torvalds 已提交
1491 1492
	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp));

1493
	if (tmp != PHASE_MSGOUT) {
1494 1495
		NCR5380_write(INITIATOR_COMMAND_REG,
		              ICR_BASE | ICR_ASSERT_ATN | ICR_ASSERT_ACK);
1496
		rc = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, 0, 3 * HZ);
1497
		if (rc < 0)
1498 1499
			goto timeout;
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
L
Linus Torvalds 已提交
1500
	}
1501

L
Linus Torvalds 已提交
1502 1503 1504 1505
	tmp = ABORT;
	msgptr = &tmp;
	len = 1;
	phase = PHASE_MSGOUT;
1506
	NCR5380_transfer_pio(instance, &phase, &len, &msgptr);
L
Linus Torvalds 已提交
1507 1508 1509 1510 1511 1512 1513

	/*
	 * If we got here, and the command completed successfully,
	 * we're about to go into bus free state.
	 */

	return len ? -1 : 0;
1514 1515 1516 1517

timeout:
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
	return -1;
L
Linus Torvalds 已提交
1518 1519
}

1520 1521
/*
 * Function : int NCR5380_transfer_dma (struct Scsi_Host *instance,
1522
 * unsigned char *phase, int *count, unsigned char **data)
L
Linus Torvalds 已提交
1523 1524
 *
 * Purpose : transfers data in given phase using either real
1525
 * or pseudo DMA.
L
Linus Torvalds 已提交
1526
 *
1527
 * Inputs : instance - instance of driver, *phase - pointer to
1528 1529
 * what phase is expected, *count - pointer to number of
 * bytes to transfer, **data - pointer to data pointer.
1530
 *
L
Linus Torvalds 已提交
1531
 * Returns : -1 when different phase is entered without transferring
1532 1533
 * maximum number of bytes, 0 if all bytes or transferred or exit
 * is in same phase.
L
Linus Torvalds 已提交
1534
 *
1535
 * Also, *phase, *count, *data are modified in place.
L
Linus Torvalds 已提交
1536 1537 1538
 */


1539 1540 1541 1542 1543
static int NCR5380_transfer_dma(struct Scsi_Host *instance,
				unsigned char *phase, int *count,
				unsigned char **data)
{
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
1544 1545 1546
	int c = *count;
	unsigned char p = *phase;
	unsigned char *d = *data;
L
Linus Torvalds 已提交
1547
	unsigned char tmp;
1548
	int result = 0;
L
Linus Torvalds 已提交
1549 1550 1551 1552 1553 1554

	if ((tmp = (NCR5380_read(STATUS_REG) & PHASE_MASK)) != p) {
		*phase = tmp;
		return -1;
	}

1555
	hostdata->connected->SCp.phase = p;
L
Linus Torvalds 已提交
1556

1557 1558 1559 1560 1561 1562
	if (p & SR_IO) {
		if (hostdata->read_overruns)
			c -= hostdata->read_overruns;
		else if (hostdata->flags & FLAG_DMA_FIXUP)
			--c;
	}
L
Linus Torvalds 已提交
1563

1564 1565
	dsprintk(NDEBUG_DMA, instance, "initializing DMA %s: length %d, address %p\n",
	         (p & SR_IO) ? "receive" : "send", c, d);
L
Linus Torvalds 已提交
1566

1567 1568 1569 1570 1571
#ifdef CONFIG_SUN3
	/* send start chain */
	sun3scsi_dma_start(c, *data);
#endif

1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584
	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
	NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
	                        MR_ENABLE_EOP_INTR);

	if (!(hostdata->flags & FLAG_LATE_DMA_SETUP)) {
		/* On the Medusa, it is a must to initialize the DMA before
		 * starting the NCR. This is also the cleaner way for the TT.
		 */
		if (p & SR_IO)
			result = NCR5380_dma_recv_setup(instance, d, c);
		else
			result = NCR5380_dma_send_setup(instance, d, c);
	}
L
Linus Torvalds 已提交
1585

1586
	/*
1587 1588
	 * On the PAS16 at least I/O recovery delays are not needed here.
	 * Everyone else seems to want them.
L
Linus Torvalds 已提交
1589 1590 1591
	 */

	if (p & SR_IO) {
1592
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1593
		NCR5380_io_delay(1);
L
Linus Torvalds 已提交
1594 1595
		NCR5380_write(START_DMA_INITIATOR_RECEIVE_REG, 0);
	} else {
1596
		NCR5380_io_delay(1);
L
Linus Torvalds 已提交
1597
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA);
1598
		NCR5380_io_delay(1);
L
Linus Torvalds 已提交
1599
		NCR5380_write(START_DMA_SEND_REG, 0);
1600
		NCR5380_io_delay(1);
L
Linus Torvalds 已提交
1601 1602
	}

1603 1604 1605 1606 1607 1608 1609
#ifdef CONFIG_SUN3
#ifdef SUN3_SCSI_VME
	dregs->csr |= CSR_DMA_ENABLE;
#endif
	sun3_dma_active = 1;
#endif

1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632
	if (hostdata->flags & FLAG_LATE_DMA_SETUP) {
		/* On the Falcon, the DMA setup must be done after the last
		 * NCR access, else the DMA setup gets trashed!
		 */
		if (p & SR_IO)
			result = NCR5380_dma_recv_setup(instance, d, c);
		else
			result = NCR5380_dma_send_setup(instance, d, c);
	}

	/* On failure, NCR5380_dma_xxxx_setup() returns a negative int. */
	if (result < 0)
		return result;

	/* For real DMA, result is the byte count. DMA interrupt is expected. */
	if (result > 0) {
		hostdata->dma_len = result;
		return 0;
	}

	/* The result is zero iff pseudo DMA send/receive was completed. */
	hostdata->dma_len = c;

L
Linus Torvalds 已提交
1633
/*
1634
 * A note regarding the DMA errata workarounds for early NMOS silicon.
F
Finn Thain 已提交
1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660
 *
 * For DMA sends, we want to wait until the last byte has been
 * transferred out over the bus before we turn off DMA mode.  Alas, there
 * seems to be no terribly good way of doing this on a 5380 under all
 * conditions.  For non-scatter-gather operations, we can wait until REQ
 * and ACK both go false, or until a phase mismatch occurs.  Gather-sends
 * are nastier, since the device will be expecting more data than we
 * are prepared to send it, and REQ will remain asserted.  On a 53C8[01] we
 * could test Last Byte Sent to assure transfer (I imagine this is precisely
 * why this signal was added to the newer chips) but on the older 538[01]
 * this signal does not exist.  The workaround for this lack is a watchdog;
 * we bail out of the wait-loop after a modest amount of wait-time if
 * the usual exit conditions are not met.  Not a terribly clean or
 * correct solution :-%
 *
 * DMA receive is equally tricky due to a nasty characteristic of the NCR5380.
 * If the chip is in DMA receive mode, it will respond to a target's
 * REQ by latching the SCSI data into the INPUT DATA register and asserting
 * ACK, even if it has _already_ been notified by the DMA controller that
 * the current DMA transfer has completed!  If the NCR5380 is then taken
 * out of DMA mode, this already-acknowledged byte is lost. This is
 * not a problem for "one DMA transfer per READ command", because
 * the situation will never arise... either all of the data is DMA'ed
 * properly, or the target switches to MESSAGE IN phase to signal a
 * disconnection (either operation bringing the DMA to a clean halt).
 * However, in order to handle scatter-receive, we must work around the
1661
 * problem.  The chosen fix is to DMA fewer bytes, then check for the
F
Finn Thain 已提交
1662 1663 1664
 * condition before taking the NCR5380 out of DMA mode.  One or two extra
 * bytes are transferred via PIO as necessary to fill out the original
 * request.
L
Linus Torvalds 已提交
1665 1666
 */

1667 1668
	if (hostdata->flags & FLAG_DMA_FIXUP) {
		if (p & SR_IO) {
L
Linus Torvalds 已提交
1669
			/*
1670
			 * The workaround was to transfer fewer bytes than we
1671
			 * intended to with the pseudo-DMA read function, wait for
L
Linus Torvalds 已提交
1672 1673
			 * the chip to latch the last byte, read it, and then disable
			 * pseudo-DMA mode.
1674
			 *
L
Linus Torvalds 已提交
1675 1676 1677 1678
			 * After REQ is asserted, the NCR5380 asserts DRQ and ACK.
			 * REQ is deasserted when ACK is asserted, and not reasserted
			 * until ACK goes false.  Since the NCR5380 won't lower ACK
			 * until DACK is asserted, which won't happen unless we twiddle
1679 1680
			 * the DMA port or we take the NCR5380 out of DMA mode, we
			 * can guarantee that we won't handshake another extra
L
Linus Torvalds 已提交
1681 1682 1683
			 * byte.
			 */

1684
			if (NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG,
1685
			                          BASR_DRQ, BASR_DRQ, HZ) < 0) {
1686
				result = -1;
1687 1688
				shost_printk(KERN_ERR, instance, "PDMA read: DRQ timeout\n");
			}
1689
			if (NCR5380_poll_politely(hostdata, STATUS_REG,
1690
			                          SR_REQ, 0, HZ) < 0) {
1691
				result = -1;
1692
				shost_printk(KERN_ERR, instance, "PDMA read: !REQ timeout\n");
L
Linus Torvalds 已提交
1693
			}
1694 1695
			d[*count - 1] = NCR5380_read(INPUT_DATA_REG);
		} else {
L
Linus Torvalds 已提交
1696
			/*
1697 1698
			 * Wait for the last byte to be sent.  If REQ is being asserted for
			 * the byte we're interested, we'll ACK it and it will go false.
L
Linus Torvalds 已提交
1699
			 */
1700
			if (NCR5380_poll_politely2(hostdata,
1701 1702
			     BUS_AND_STATUS_REG, BASR_DRQ, BASR_DRQ,
			     BUS_AND_STATUS_REG, BASR_PHASE_MATCH, 0, HZ) < 0) {
1703
				result = -1;
1704
				shost_printk(KERN_ERR, instance, "PDMA write: DRQ and phase timeout\n");
L
Linus Torvalds 已提交
1705 1706 1707
			}
		}
	}
1708 1709

	NCR5380_dma_complete(instance);
1710
	return result;
L
Linus Torvalds 已提交
1711 1712 1713 1714 1715
}

/*
 * Function : NCR5380_information_transfer (struct Scsi_Host *instance)
 *
1716
 * Purpose : run through the various SCSI phases and do as the target
1717 1718
 * directs us to.  Operates on the currently connected command,
 * instance->connected.
L
Linus Torvalds 已提交
1719 1720 1721
 *
 * Inputs : instance, instance for which we are doing commands
 *
1722
 * Side effects : SCSI things happen, the disconnected queue will be
1723 1724
 * modified if a command disconnects, *instance->connected will
 * change.
L
Linus Torvalds 已提交
1725
 *
1726
 * XXX Note : we need to watch for bus free or a reset condition here
1727
 * to recover from an unexpected bus free condition.
L
Linus Torvalds 已提交
1728 1729
 */

1730 1731
static void NCR5380_information_transfer(struct Scsi_Host *instance)
{
F
Finn Thain 已提交
1732
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
1733 1734 1735 1736 1737 1738
	unsigned char msgout = NOP;
	int sink = 0;
	int len;
	int transfersize;
	unsigned char *data;
	unsigned char phase, tmp, extended_msg[10], old_phase = 0xff;
1739
	struct scsi_cmnd *cmd;
L
Linus Torvalds 已提交
1740

1741 1742 1743 1744
#ifdef SUN3_SCSI_VME
	dregs->csr |= CSR_INTR;
#endif

1745
	while ((cmd = hostdata->connected)) {
1746 1747
		struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);

L
Linus Torvalds 已提交
1748 1749 1750 1751 1752 1753 1754 1755
		tmp = NCR5380_read(STATUS_REG);
		/* We only have a valid SCSI phase when REQ is asserted */
		if (tmp & SR_REQ) {
			phase = (tmp & PHASE_MASK);
			if (phase != old_phase) {
				old_phase = phase;
				NCR5380_dprint_phase(NDEBUG_INFORMATION, instance);
			}
1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780
#ifdef CONFIG_SUN3
			if (phase == PHASE_CMDOUT) {
				void *d;
				unsigned long count;

				if (!cmd->SCp.this_residual && cmd->SCp.buffers_residual) {
					count = cmd->SCp.buffer->length;
					d = sg_virt(cmd->SCp.buffer);
				} else {
					count = cmd->SCp.this_residual;
					d = cmd->SCp.ptr;
				}

				if (sun3_dma_setup_done != cmd &&
				    sun3scsi_dma_xfer_len(count, cmd) > 0) {
					sun3scsi_dma_setup(instance, d, count,
					                   rq_data_dir(cmd->request));
					sun3_dma_setup_done = cmd;
				}
#ifdef SUN3_SCSI_VME
				dregs->csr |= CSR_INTR;
#endif
			}
#endif /* CONFIG_SUN3 */

L
Linus Torvalds 已提交
1781 1782 1783
			if (sink && (phase != PHASE_MSGOUT)) {
				NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp));

1784 1785
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN |
				              ICR_ASSERT_ACK);
1786 1787
				while (NCR5380_read(STATUS_REG) & SR_REQ)
					;
1788 1789
				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
				              ICR_ASSERT_ATN);
L
Linus Torvalds 已提交
1790 1791 1792
				sink = 0;
				continue;
			}
1793

L
Linus Torvalds 已提交
1794 1795 1796
			switch (phase) {
			case PHASE_DATAOUT:
#if (NDEBUG & NDEBUG_NO_DATAOUT)
1797
				shost_printk(KERN_DEBUG, instance, "NDEBUG_NO_DATAOUT set, attempted DATAOUT aborted\n");
L
Linus Torvalds 已提交
1798 1799 1800
				sink = 1;
				do_abort(instance);
				cmd->result = DID_ERROR << 16;
1801
				complete_cmd(instance, cmd);
F
Finn Thain 已提交
1802
				hostdata->connected = NULL;
L
Linus Torvalds 已提交
1803 1804
				return;
#endif
F
Finn Thain 已提交
1805
			case PHASE_DATAIN:
1806
				/*
L
Linus Torvalds 已提交
1807 1808 1809 1810 1811 1812 1813 1814
				 * If there is no room left in the current buffer in the
				 * scatter-gather list, move onto the next one.
				 */

				if (!cmd->SCp.this_residual && cmd->SCp.buffers_residual) {
					++cmd->SCp.buffer;
					--cmd->SCp.buffers_residual;
					cmd->SCp.this_residual = cmd->SCp.buffer->length;
J
Jens Axboe 已提交
1815
					cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
1816 1817 1818
					dsprintk(NDEBUG_INFORMATION, instance, "%d bytes and %d buffers left\n",
					         cmd->SCp.this_residual,
					         cmd->SCp.buffers_residual);
L
Linus Torvalds 已提交
1819
				}
1820

L
Linus Torvalds 已提交
1821
				/*
1822
				 * The preferred transfer method is going to be
L
Linus Torvalds 已提交
1823 1824 1825 1826 1827 1828 1829 1830
				 * PSEUDO-DMA for systems that are strictly PIO,
				 * since we can let the hardware do the handshaking.
				 *
				 * For this to work, we need to know the transfersize
				 * ahead of time, since the pseudo-DMA code will sit
				 * in an unconditional loop.
				 */

1831
				transfersize = 0;
1832
				if (!cmd->device->borken)
1833 1834
					transfersize = NCR5380_dma_xfer_len(instance, cmd, phase);

1835
				if (transfersize > 0) {
L
Linus Torvalds 已提交
1836
					len = transfersize;
1837 1838
					if (NCR5380_transfer_dma(instance, &phase,
					    &len, (unsigned char **)&cmd->SCp.ptr)) {
L
Linus Torvalds 已提交
1839
						/*
1840 1841 1842
						 * If the watchdog timer fires, all future
						 * accesses to this device will use the
						 * polled-IO.
L
Linus Torvalds 已提交
1843
						 */
J
Jeff Garzik 已提交
1844
						scmd_printk(KERN_INFO, cmd,
1845
							"switching to slow handshake\n");
L
Linus Torvalds 已提交
1846 1847 1848 1849 1850
						cmd->device->borken = 1;
						sink = 1;
						do_abort(instance);
						cmd->result = DID_ERROR << 16;
						/* XXX - need to source or sink data here, as appropriate */
1851
					}
F
Finn Thain 已提交
1852
				} else {
1853 1854
					/* Transfer a small chunk so that the
					 * irq mode lock is not held too long.
1855
					 */
1856 1857
					transfersize = min(cmd->SCp.this_residual,
							   NCR5380_PIO_CHUNK_SIZE);
1858 1859
					len = transfersize;
					NCR5380_transfer_pio(instance, &phase, &len,
1860
					                     (unsigned char **)&cmd->SCp.ptr);
1861
					cmd->SCp.this_residual -= transfersize - len;
1862
				}
1863 1864 1865 1866
#ifdef CONFIG_SUN3
				if (sun3_dma_setup_done == cmd)
					sun3_dma_setup_done = NULL;
#endif
1867
				return;
L
Linus Torvalds 已提交
1868 1869 1870 1871 1872 1873 1874 1875 1876 1877 1878 1879
			case PHASE_MSGIN:
				len = 1;
				data = &tmp;
				NCR5380_transfer_pio(instance, &phase, &len, &data);
				cmd->SCp.Message = tmp;

				switch (tmp) {
				case ABORT:
				case COMMAND_COMPLETE:
					/* Accept message by clearing ACK */
					sink = 1;
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1880 1881 1882 1883
					dsprintk(NDEBUG_QUEUES, instance,
					         "COMMAND COMPLETE %p target %d lun %llu\n",
					         cmd, scmd_id(cmd), cmd->device->lun);

L
Linus Torvalds 已提交
1884 1885
					hostdata->connected = NULL;

F
Finn Thain 已提交
1886 1887 1888
					cmd->result &= ~0xffff;
					cmd->result |= cmd->SCp.Status;
					cmd->result |= cmd->SCp.Message << 8;
1889

F
Finn Thain 已提交
1890
					if (cmd->cmnd[0] == REQUEST_SENSE)
1891
						complete_cmd(instance, cmd);
F
Finn Thain 已提交
1892 1893 1894 1895 1896 1897 1898 1899 1900
					else {
						if (cmd->SCp.Status == SAM_STAT_CHECK_CONDITION ||
						    cmd->SCp.Status == SAM_STAT_COMMAND_TERMINATED) {
							dsprintk(NDEBUG_QUEUES, instance, "autosense: adding cmd %p to tail of autosense queue\n",
							         cmd);
							list_add_tail(&ncmd->list,
							              &hostdata->autosense);
						} else
							complete_cmd(instance, cmd);
L
Linus Torvalds 已提交
1901 1902
					}

1903 1904
					/*
					 * Restore phase bits to 0 so an interrupted selection,
L
Linus Torvalds 已提交
1905 1906 1907
					 * arbitration can resume.
					 */
					NCR5380_write(TARGET_COMMAND_REG, 0);
1908 1909 1910

					/* Enable reselect interrupts */
					NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
1911 1912

					maybe_release_dma_irq(instance);
L
Linus Torvalds 已提交
1913 1914 1915 1916 1917 1918 1919 1920 1921
					return;
				case MESSAGE_REJECT:
					/* Accept message by clearing ACK */
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
					switch (hostdata->last_message) {
					case HEAD_OF_QUEUE_TAG:
					case ORDERED_QUEUE_TAG:
					case SIMPLE_QUEUE_TAG:
						cmd->device->simple_tags = 0;
H
Hannes Reinecke 已提交
1922
						hostdata->busy[cmd->device->id] |= (1 << (cmd->device->lun & 0xFF));
L
Linus Torvalds 已提交
1923 1924 1925 1926
						break;
					default:
						break;
					}
1927
					break;
1928 1929 1930 1931 1932 1933 1934 1935
				case DISCONNECT:
					/* Accept message by clearing ACK */
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
					hostdata->connected = NULL;
					list_add(&ncmd->list, &hostdata->disconnected);
					dsprintk(NDEBUG_INFORMATION | NDEBUG_QUEUES,
					         instance, "connected command %p for target %d lun %llu moved to disconnected queue\n",
					         cmd, scmd_id(cmd), cmd->device->lun);
1936

1937 1938 1939 1940 1941
					/*
					 * Restore phase bits to 0 so an interrupted selection,
					 * arbitration can resume.
					 */
					NCR5380_write(TARGET_COMMAND_REG, 0);
L
Linus Torvalds 已提交
1942

1943 1944
					/* Enable reselect interrupts */
					NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
1945 1946 1947
#ifdef SUN3_SCSI_VME
					dregs->csr |= CSR_DMA_ENABLE;
#endif
1948
					return;
1949
					/*
L
Linus Torvalds 已提交
1950
					 * The SCSI data pointer is *IMPLICITLY* saved on a disconnect
1951
					 * operation, in violation of the SCSI spec so we can safely
L
Linus Torvalds 已提交
1952 1953
					 * ignore SAVE/RESTORE pointers calls.
					 *
1954
					 * Unfortunately, some disks violate the SCSI spec and
L
Linus Torvalds 已提交
1955
					 * don't issue the required SAVE_POINTERS message before
1956
					 * disconnecting, and we have to break spec to remain
L
Linus Torvalds 已提交
1957 1958 1959 1960 1961 1962 1963 1964
					 * compatible.
					 */
				case SAVE_POINTERS:
				case RESTORE_POINTERS:
					/* Accept message by clearing ACK */
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
					break;
				case EXTENDED_MESSAGE:
F
Finn Thain 已提交
1965 1966 1967 1968
					/*
					 * Start the message buffer with the EXTENDED_MESSAGE
					 * byte, since spi_print_msg() wants the whole thing.
					 */
L
Linus Torvalds 已提交
1969 1970 1971
					extended_msg[0] = EXTENDED_MESSAGE;
					/* Accept first byte by clearing ACK */
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
1972 1973 1974

					spin_unlock_irq(&hostdata->lock);

1975
					dsprintk(NDEBUG_EXTENDED, instance, "receiving extended message\n");
L
Linus Torvalds 已提交
1976 1977 1978 1979 1980

					len = 2;
					data = extended_msg + 1;
					phase = PHASE_MSGIN;
					NCR5380_transfer_pio(instance, &phase, &len, &data);
1981 1982 1983
					dsprintk(NDEBUG_EXTENDED, instance, "length %d, code 0x%02x\n",
					         (int)extended_msg[1],
					         (int)extended_msg[2]);
L
Linus Torvalds 已提交
1984

1985 1986
					if (!len && extended_msg[1] > 0 &&
					    extended_msg[1] <= sizeof(extended_msg) - 2) {
L
Linus Torvalds 已提交
1987 1988 1989 1990 1991 1992 1993
						/* Accept third byte by clearing ACK */
						NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
						len = extended_msg[1] - 1;
						data = extended_msg + 3;
						phase = PHASE_MSGIN;

						NCR5380_transfer_pio(instance, &phase, &len, &data);
1994 1995
						dsprintk(NDEBUG_EXTENDED, instance, "message received, residual %d\n",
						         len);
L
Linus Torvalds 已提交
1996 1997 1998 1999 2000 2001 2002 2003 2004

						switch (extended_msg[2]) {
						case EXTENDED_SDTR:
						case EXTENDED_WDTR:
						case EXTENDED_MODIFY_DATA_POINTER:
						case EXTENDED_EXTENDED_IDENTIFY:
							tmp = 0;
						}
					} else if (len) {
2005
						shost_printk(KERN_ERR, instance, "error receiving extended message\n");
L
Linus Torvalds 已提交
2006 2007
						tmp = 0;
					} else {
2008 2009
						shost_printk(KERN_NOTICE, instance, "extended message code %02x length %d is too long\n",
						             extended_msg[2], extended_msg[1]);
L
Linus Torvalds 已提交
2010 2011
						tmp = 0;
					}
2012 2013 2014 2015 2016

					spin_lock_irq(&hostdata->lock);
					if (!hostdata->connected)
						return;

L
Linus Torvalds 已提交
2017 2018
					/* Fall through to reject message */

2019 2020
					/*
					 * If we get something weird that we aren't expecting,
L
Linus Torvalds 已提交
2021 2022 2023 2024
					 * reject it.
					 */
				default:
					if (!tmp) {
2025
						shost_printk(KERN_ERR, instance, "rejecting message ");
2026
						spi_print_msg(extended_msg);
L
Linus Torvalds 已提交
2027 2028
						printk("\n");
					} else if (tmp != EXTENDED_MESSAGE)
J
Jeff Garzik 已提交
2029
						scmd_printk(KERN_INFO, cmd,
2030 2031
						            "rejecting unknown message %02x\n",
						            tmp);
L
Linus Torvalds 已提交
2032
					else
J
Jeff Garzik 已提交
2033
						scmd_printk(KERN_INFO, cmd,
2034 2035
						            "rejecting unknown extended message code %02x, length %d\n",
						            extended_msg[1], extended_msg[0]);
L
Linus Torvalds 已提交
2036 2037 2038 2039

					msgout = MESSAGE_REJECT;
					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
					break;
2040
				} /* switch (tmp) */
L
Linus Torvalds 已提交
2041 2042 2043 2044 2045 2046 2047 2048 2049
				break;
			case PHASE_MSGOUT:
				len = 1;
				data = &msgout;
				hostdata->last_message = msgout;
				NCR5380_transfer_pio(instance, &phase, &len, &data);
				if (msgout == ABORT) {
					hostdata->connected = NULL;
					cmd->result = DID_ERROR << 16;
2050
					complete_cmd(instance, cmd);
2051
					maybe_release_dma_irq(instance);
L
Linus Torvalds 已提交
2052 2053 2054 2055 2056 2057 2058 2059
					NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
					return;
				}
				msgout = NOP;
				break;
			case PHASE_CMDOUT:
				len = cmd->cmd_len;
				data = cmd->cmnd;
2060 2061 2062 2063
				/*
				 * XXX for performance reasons, on machines with a
				 * PSEUDO-DMA architecture we should probably
				 * use the dma transfer function.
L
Linus Torvalds 已提交
2064 2065 2066 2067 2068 2069 2070 2071 2072 2073
				 */
				NCR5380_transfer_pio(instance, &phase, &len, &data);
				break;
			case PHASE_STATIN:
				len = 1;
				data = &tmp;
				NCR5380_transfer_pio(instance, &phase, &len, &data);
				cmd->SCp.Status = tmp;
				break;
			default:
2074
				shost_printk(KERN_ERR, instance, "unknown phase\n");
2075
				NCR5380_dprint(NDEBUG_ANY, instance);
2076
			} /* switch(phase) */
2077
		} else {
2078
			spin_unlock_irq(&hostdata->lock);
2079
			NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, HZ);
2080
			spin_lock_irq(&hostdata->lock);
L
Linus Torvalds 已提交
2081
		}
2082
	}
L
Linus Torvalds 已提交
2083 2084 2085 2086 2087
}

/*
 * Function : void NCR5380_reselect (struct Scsi_Host *instance)
 *
2088
 * Purpose : does reselection, initializing the instance->connected
2089 2090
 * field to point to the scsi_cmnd for which the I_T_L or I_T_L_Q
 * nexus has been reestablished,
2091
 *
L
Linus Torvalds 已提交
2092 2093 2094
 * Inputs : instance - this instance of the NCR5380.
 */

2095 2096
static void NCR5380_reselect(struct Scsi_Host *instance)
{
F
Finn Thain 已提交
2097
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
L
Linus Torvalds 已提交
2098
	unsigned char target_mask;
2099
	unsigned char lun;
L
Linus Torvalds 已提交
2100
	unsigned char msg[3];
2101 2102
	struct NCR5380_cmd *ncmd;
	struct scsi_cmnd *tmp;
L
Linus Torvalds 已提交
2103 2104 2105 2106 2107 2108 2109 2110 2111

	/*
	 * Disable arbitration, etc. since the host adapter obviously
	 * lost, and tell an interrupted NCR5380_select() to restart.
	 */

	NCR5380_write(MODE_REG, MR_BASE);

	target_mask = NCR5380_read(CURRENT_SCSI_DATA_REG) & ~(hostdata->id_mask);
2112 2113

	dsprintk(NDEBUG_RESELECTION, instance, "reselect\n");
L
Linus Torvalds 已提交
2114

2115
	/*
L
Linus Torvalds 已提交
2116 2117 2118 2119 2120 2121 2122 2123 2124
	 * At this point, we have detected that our SCSI ID is on the bus,
	 * SEL is true and BSY was false for at least one bus settle delay
	 * (400 ns).
	 *
	 * We must assert BSY ourselves, until the target drops the SEL
	 * signal.
	 */

	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY);
2125
	if (NCR5380_poll_politely(hostdata,
2126 2127 2128 2129
	                          STATUS_REG, SR_SEL, 0, 2 * HZ) < 0) {
		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
		return;
	}
L
Linus Torvalds 已提交
2130 2131 2132 2133 2134 2135
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

	/*
	 * Wait for target to go into MSGIN.
	 */

2136
	if (NCR5380_poll_politely(hostdata,
2137 2138 2139 2140
	                          STATUS_REG, SR_REQ, SR_REQ, 2 * HZ) < 0) {
		do_abort(instance);
		return;
	}
L
Linus Torvalds 已提交
2141

2142 2143 2144
#ifdef CONFIG_SUN3
	/* acknowledge toggle to MSGIN */
	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(PHASE_MSGIN));
L
Linus Torvalds 已提交
2145

2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159
	/* peek at the byte without really hitting the bus */
	msg[0] = NCR5380_read(CURRENT_SCSI_DATA_REG);
#else
	{
		int len = 1;
		unsigned char *data = msg;
		unsigned char phase = PHASE_MSGIN;

		NCR5380_transfer_pio(instance, &phase, &len, &data);

		if (len) {
			do_abort(instance);
			return;
		}
2160
	}
2161
#endif /* CONFIG_SUN3 */
2162

L
Linus Torvalds 已提交
2163
	if (!(msg[0] & 0x80)) {
2164
		shost_printk(KERN_ERR, instance, "expecting IDENTIFY message, got ");
2165
		spi_print_msg(msg);
2166 2167 2168 2169 2170
		printk("\n");
		do_abort(instance);
		return;
	}
	lun = msg[0] & 0x07;
L
Linus Torvalds 已提交
2171

2172 2173 2174 2175 2176
	/*
	 * We need to add code for SCSI-II to track which devices have
	 * I_T_L_Q nexuses established, and which have simple I_T_L
	 * nexuses so we can chose to do additional data transfer.
	 */
L
Linus Torvalds 已提交
2177

2178 2179 2180 2181
	/*
	 * Find the command corresponding to the I_T_L or I_T_L_Q  nexus we
	 * just reestablished, and remove it from the disconnected queue.
	 */
L
Linus Torvalds 已提交
2182

2183 2184 2185 2186 2187 2188 2189 2190
	tmp = NULL;
	list_for_each_entry(ncmd, &hostdata->disconnected, list) {
		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);

		if (target_mask == (1 << scmd_id(cmd)) &&
		    lun == (u8)cmd->device->lun) {
			list_del(&ncmd->list);
			tmp = cmd;
2191
			break;
L
Linus Torvalds 已提交
2192 2193
		}
	}
2194 2195 2196 2197 2198

	if (tmp) {
		dsprintk(NDEBUG_RESELECTION | NDEBUG_QUEUES, instance,
		         "reselect: removed %p from disconnected queue\n", tmp);
	} else {
2199 2200 2201
		shost_printk(KERN_ERR, instance, "target bitmask 0x%02x lun %d not in disconnected queue.\n",
		             target_mask, lun);
		/*
2202 2203
		 * Since we have an established nexus that we can't do anything
		 * with, we must abort it.
2204
		 */
L
Linus Torvalds 已提交
2205
		do_abort(instance);
2206
		return;
L
Linus Torvalds 已提交
2207
	}
2208

2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221 2222 2223 2224 2225 2226 2227 2228 2229 2230 2231 2232
#ifdef CONFIG_SUN3
	{
		void *d;
		unsigned long count;

		if (!tmp->SCp.this_residual && tmp->SCp.buffers_residual) {
			count = tmp->SCp.buffer->length;
			d = sg_virt(tmp->SCp.buffer);
		} else {
			count = tmp->SCp.this_residual;
			d = tmp->SCp.ptr;
		}

		if (sun3_dma_setup_done != tmp &&
		    sun3scsi_dma_xfer_len(count, tmp) > 0) {
			sun3scsi_dma_setup(instance, d, count,
			                   rq_data_dir(tmp->request));
			sun3_dma_setup_done = tmp;
		}
	}

	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK);
#endif /* CONFIG_SUN3 */

2233 2234 2235 2236
	/* Accept message by clearing ACK */
	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

	hostdata->connected = tmp;
2237 2238
	dsprintk(NDEBUG_RESELECTION, instance, "nexus established, target %d, lun %llu\n",
	         scmd_id(tmp), tmp->device->lun);
L
Linus Torvalds 已提交
2239 2240
}

2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254 2255 2256 2257 2258 2259 2260 2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293
/**
 * list_find_cmd - test for presence of a command in a linked list
 * @haystack: list of commands
 * @needle: command to search for
 */

static bool list_find_cmd(struct list_head *haystack,
                          struct scsi_cmnd *needle)
{
	struct NCR5380_cmd *ncmd;

	list_for_each_entry(ncmd, haystack, list)
		if (NCR5380_to_scmd(ncmd) == needle)
			return true;
	return false;
}

/**
 * list_remove_cmd - remove a command from linked list
 * @haystack: list of commands
 * @needle: command to remove
 */

static bool list_del_cmd(struct list_head *haystack,
                         struct scsi_cmnd *needle)
{
	if (list_find_cmd(haystack, needle)) {
		struct NCR5380_cmd *ncmd = scsi_cmd_priv(needle);

		list_del(&ncmd->list);
		return true;
	}
	return false;
}

/**
 * NCR5380_abort - scsi host eh_abort_handler() method
 * @cmd: the command to be aborted
 *
 * Try to abort a given command by removing it from queues and/or sending
 * the target an abort message. This may not succeed in causing a target
 * to abort the command. Nonetheless, the low-level driver must forget about
 * the command because the mid-layer reclaims it and it may be re-issued.
 *
 * The normal path taken by a command is as follows. For EH we trace this
 * same path to locate and abort the command.
 *
 * unissued -> selecting -> [unissued -> selecting ->]... connected ->
 * [disconnected -> connected ->]...
 * [autosense -> connected ->] done
 *
 * If cmd was not found at all then presumably it has already been completed,
 * in which case return SUCCESS to try to avoid further EH measures.
F
Finn Thain 已提交
2294
 *
2295
 * If the command has not completed yet, we must not fail to find it.
F
Finn Thain 已提交
2296 2297 2298 2299
 * We have no option but to forget the aborted command (even if it still
 * lacks sense data). The mid-layer may re-issue a command that is in error
 * recovery (see scsi_send_eh_cmnd), but the logic and data structures in
 * this driver are such that a command can appear on one queue only.
2300 2301 2302
 *
 * The lock protects driver data structures, but EH handlers also use it
 * to serialize their own execution and prevent their own re-entry.
L
Linus Torvalds 已提交
2303 2304
 */

F
Finn Thain 已提交
2305 2306
static int NCR5380_abort(struct scsi_cmnd *cmd)
{
L
Linus Torvalds 已提交
2307
	struct Scsi_Host *instance = cmd->device->host;
F
Finn Thain 已提交
2308
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
2309
	unsigned long flags;
2310
	int result = SUCCESS;
2311

2312 2313
	spin_lock_irqsave(&hostdata->lock, flags);

2314
#if (NDEBUG & NDEBUG_ANY)
2315
	scmd_printk(KERN_INFO, cmd, __func__);
2316
#endif
2317 2318
	NCR5380_dprint(NDEBUG_ANY, instance);
	NCR5380_dprint_phase(NDEBUG_ANY, instance);
L
Linus Torvalds 已提交
2319

2320 2321 2322 2323 2324
	if (list_del_cmd(&hostdata->unissued, cmd)) {
		dsprintk(NDEBUG_ABORT, instance,
		         "abort: removed %p from issue queue\n", cmd);
		cmd->result = DID_ABORT << 16;
		cmd->scsi_done(cmd); /* No tag or busy flag to worry about */
F
Finn Thain 已提交
2325
		goto out;
2326 2327
	}

2328 2329 2330 2331 2332 2333 2334 2335 2336
	if (hostdata->selecting == cmd) {
		dsprintk(NDEBUG_ABORT, instance,
		         "abort: cmd %p == selecting\n", cmd);
		hostdata->selecting = NULL;
		cmd->result = DID_ABORT << 16;
		complete_cmd(instance, cmd);
		goto out;
	}

2337 2338 2339
	if (list_del_cmd(&hostdata->disconnected, cmd)) {
		dsprintk(NDEBUG_ABORT, instance,
		         "abort: removed %p from disconnected list\n", cmd);
2340 2341 2342
		/* Can't call NCR5380_select() and send ABORT because that
		 * means releasing the lock. Need a bus reset.
		 */
F
Finn Thain 已提交
2343 2344
		set_host_byte(cmd, DID_ERROR);
		complete_cmd(instance, cmd);
2345 2346
		result = FAILED;
		goto out;
2347 2348 2349 2350 2351 2352 2353 2354 2355 2356 2357 2358 2359
	}

	if (hostdata->connected == cmd) {
		dsprintk(NDEBUG_ABORT, instance, "abort: cmd %p is connected\n", cmd);
		hostdata->connected = NULL;
		hostdata->dma_len = 0;
		if (do_abort(instance)) {
			set_host_byte(cmd, DID_ERROR);
			complete_cmd(instance, cmd);
			result = FAILED;
			goto out;
		}
		set_host_byte(cmd, DID_ABORT);
F
Finn Thain 已提交
2360 2361 2362 2363 2364 2365 2366 2367
		complete_cmd(instance, cmd);
		goto out;
	}

	if (list_del_cmd(&hostdata->autosense, cmd)) {
		dsprintk(NDEBUG_ABORT, instance,
		         "abort: removed %p from sense queue\n", cmd);
		set_host_byte(cmd, DID_ERROR);
2368 2369 2370 2371 2372 2373 2374 2375 2376 2377
		complete_cmd(instance, cmd);
	}

out:
	if (result == FAILED)
		dsprintk(NDEBUG_ABORT, instance, "abort: failed to abort %p\n", cmd);
	else
		dsprintk(NDEBUG_ABORT, instance, "abort: successfully aborted %p\n", cmd);

	queue_work(hostdata->work_q, &hostdata->main_task);
2378
	maybe_release_dma_irq(instance);
2379
	spin_unlock_irqrestore(&hostdata->lock, flags);
2380

2381
	return result;
L
Linus Torvalds 已提交
2382 2383 2384
}


2385 2386 2387
/**
 * NCR5380_bus_reset - reset the SCSI bus
 * @cmd: SCSI command undergoing EH
L
Linus Torvalds 已提交
2388
 *
2389
 * Returns SUCCESS
L
Linus Torvalds 已提交
2390 2391
 */

F
Finn Thain 已提交
2392
static int NCR5380_bus_reset(struct scsi_cmnd *cmd)
2393 2394
{
	struct Scsi_Host *instance = cmd->device->host;
2395
	struct NCR5380_hostdata *hostdata = shost_priv(instance);
2396
	int i;
2397
	unsigned long flags;
2398
	struct NCR5380_cmd *ncmd;
2399

2400
	spin_lock_irqsave(&hostdata->lock, flags);
2401 2402

#if (NDEBUG & NDEBUG_ANY)
2403
	scmd_printk(KERN_INFO, cmd, __func__);
2404
#endif
2405 2406
	NCR5380_dprint(NDEBUG_ANY, instance);
	NCR5380_dprint_phase(NDEBUG_ANY, instance);
2407 2408

	do_reset(instance);
2409

2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420
	/* reset NCR registers */
	NCR5380_write(MODE_REG, MR_BASE);
	NCR5380_write(TARGET_COMMAND_REG, 0);
	NCR5380_write(SELECT_ENABLE_REG, 0);

	/* After the reset, there are no more connected or disconnected commands
	 * and no busy units; so clear the low-level status here to avoid
	 * conflicts when the mid-level code tries to wake up the affected
	 * commands!
	 */

2421 2422 2423 2424 2425 2426 2427 2428 2429 2430
	if (list_del_cmd(&hostdata->unissued, cmd)) {
		cmd->result = DID_RESET << 16;
		cmd->scsi_done(cmd);
	}

	if (hostdata->selecting) {
		hostdata->selecting->result = DID_RESET << 16;
		complete_cmd(instance, hostdata->selecting);
		hostdata->selecting = NULL;
	}
2431 2432 2433 2434 2435

	list_for_each_entry(ncmd, &hostdata->disconnected, list) {
		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);

		set_host_byte(cmd, DID_RESET);
2436
		complete_cmd(instance, cmd);
2437
	}
2438
	INIT_LIST_HEAD(&hostdata->disconnected);
2439 2440 2441 2442 2443 2444 2445

	list_for_each_entry(ncmd, &hostdata->autosense, list) {
		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);

		set_host_byte(cmd, DID_RESET);
		cmd->scsi_done(cmd);
	}
2446
	INIT_LIST_HEAD(&hostdata->autosense);
2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458

	if (hostdata->connected) {
		set_host_byte(hostdata->connected, DID_RESET);
		complete_cmd(instance, hostdata->connected);
		hostdata->connected = NULL;
	}

	for (i = 0; i < 8; ++i)
		hostdata->busy[i] = 0;
	hostdata->dma_len = 0;

	queue_work(hostdata->work_q, &hostdata->main_task);
2459
	maybe_release_dma_irq(instance);
2460
	spin_unlock_irqrestore(&hostdata->lock, flags);
L
Linus Torvalds 已提交
2461 2462 2463

	return SUCCESS;
}