- 27 4月, 2019 28 次提交
-
-
由 Adam Ford 提交于
A previous patch converted a bunch of settings for CONFIG_SF_DEFAULT but it broke the SPI Flash which now prevents booting. This patch now correctly sets CONFIG_SF_DEFAULT_SPEED=30000000 to match what it was before the conversion. Fixes: 14453fbf ("Convert CONFIG_SF_DEFAULT_* to Kconfig") Signed-off-by: NAdam Ford <aford173@gmail.com>
-
由 Björn Stenberg 提交于
addr0 is being freed twice, leading to segmentation fault Signed-off-by: NBjörn Stenberg <bjorn@haxx.se>
-
由 Gregory CLEMENT 提交于
The match controller register is not cleared during initialization. However, some bits of this register may reset the TC if tnMRx match it. As we can't make any assumption about how U-Boot is launched by the first stage bootloader (such as S1L) clearing this register ensure that the timers work as expected. Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>
-
由 Gregory CLEMENT 提交于
Since the introduction of the driver, some memory in IRAM is reserved for the TX buffers. However there are not used but instead of it, it is the buffer provided by the net stack which is used. As stated in the comment of the driver, not using the IRAM buffer could cause cache issue and lower the throughput. For the second argument it is less the case for transmitting buffers because the throughput gain in IRAM is mitigated by the time to copy the data from RAM to IRAM, but the first argument is still valid and indeed this patch fixes issue seen with Ethernet on some boards Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>
-
由 Gregory CLEMENT 提交于
The purpose of "mtd: nand: raw: allow to disable unneeded ECC layouts" was to allow disabling the default ECC layouts if a driver is known to provide its own ECC layout. However, this commit did the opposite and disabled the default layout when it was _not_ selected. It breaks all the NAND drivers not providing their own ECC layout this patch fix this situation. It was tested with the lpc32xx_nand_slc driver. Fixes: a38c3af8 ("mtd: nand: raw: allow to disable unneeded ECC layouts") Reviewed-by: NMiquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com> Tested-by: NEugen Hristev <eugen.hristev@microchip.com>
-
由 Heiko Schocher 提交于
generate define for an alias only if the struct is not created already. This prevents compilerwarning: PLAT spl/dts/dt-platdata.o spl/dts/dt-platdata.c:11:46: error: missing braces around initializer [-Werror=missing-braces] static const struct dtd_simple_bus dtv_ahb = { ^ spl/dts/dt-platdata.c:20:46: error: missing braces around initializer [-Werror=missing-braces] static const struct dtd_simple_bus dtv_apb = { ^ cc1: all warnings being treated as errors on the at91 based taurus board. Reason is in at91sam9260.dtsi is defined: ahb { compatible = "simple-bus"; ranges; and later: pinctrl: pinctrl@fffff400 { compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; ranges = <0xfffff400 0xfffff400 0x600>; without this patch dtoc generates: struct dtd_atmel_at91rm9200_pinctrl { fdt32_t atmel_mux_mask[6]; fdt32_t ranges[3]; fdt32_t reg[6]; }; struct dtd_simple_bus { bool ranges; }; "#define dtd_simple_bus dtd_atmel_at91rm9200_pinctrl" and the line with "define dtd_simple_bus..." introduces the warning. This define is not needed. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Pierre Bourdon 提交于
btrfs_search_tree should return the first item in the tree that is greater or equal to the searched item. The search algorithm did not properly handle the edge case where the searched item is higher than the last item of the node but lower than the first item of the next node. Instead of properly returning the first item of the next node, it was returning an invalid path pointer (pointing to a non-existent item after the last item of the node + 1). This fixes two issues in the btrfs driver: - Looking for a ROOT_ITEM could fail if it was the first item of its leaf node. - Iterating through DIR_INDEX entries (for readdir) could fail if the first DIR_INDEX entry was the first item of a leaf node. Signed-off-by: NPierre Bourdon <delroth@gmail.com> Cc: Marek Behun <marek.behun@nic.cz>
-
由 Ismael Luceno Cortes 提交于
Signed-off-by: NIsmael Luceno <ismael.luceno@silicon-gears.com>
-
由 Pierre Bourdon 提交于
ROOT_ITEMs in btrfs are referenced without knowing their actual "offset" value. To perform these searches using only two items from the key, the btrfs driver uses a special "btrfs_search_tree_key_type" function. The algorithm used by that function to transform a 3-tuple search into a 2-tuple search was subtly broken, leading to items not being found if they were the first in their tree node. This commit fixes btrfs_search_tree_key_type to properly behave in these situations. Signed-off-by: NPierre Bourdon <delroth@gmail.com> Cc: Marek Behun <marek.behun@nic.cz>
-
由 Andrew F. Davis 提交于
Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NAndreas Dannenberg <dannenberg@ti.com>
-
由 Andrew F. Davis 提交于
Add new defconfig files for the AM65x High Security EVM. This defconfigs are the same as for the non-secure part, except for: CONFIG_TI_SECURE_DEVICE option set to 'y' CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y' CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y' Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NAndreas Dannenberg <dannenberg@ti.com>
-
由 Andrew F. Davis 提交于
K3 HS devices require signed binaries for boot, use the SECDEV tools to sign the boot artifacts during build. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NAndreas Dannenberg <dannenberg@ti.com>
-
由 Andrew F. Davis 提交于
K3 devices have High Security (HS) variants along with the non-HS already supported. Like the previous generation devices (OMAP/Keystone2) K3 supports boot chain-of-trust by authenticating and optionally decrypting images as they are unpacked from FIT images. Add support for this here. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NAndreas Dannenberg <dannenberg@ti.com>
-
由 Andrew F. Davis 提交于
SYSFW version 2019.01 introduces a slightly modified version of this API, add support for it here. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NAndreas Dannenberg <dannenberg@ti.com>
-
由 Andrew F. Davis 提交于
TI-SCI message protocol provides support for controlling the firewall configurations available in SoC. Introduce support for the set of TI-SCI message protocol APIs that provide us with this capability of controlling firewalls. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NAndreas Dannenberg <dannenberg@ti.com>
-
由 Andrew F. Davis 提交于
On HS devices the 512b region of reset isolated memory called MCU_PSRAM0 is firewalled by default. Until SYSFW is loaded we cannot use this memory. It is only used to store a single value left at the end of SRAM by ROM that will be needed later. Save that value to a global variable stored in the .data section. This section is used as .bss will be cleared between saving this value and using it. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NAndreas Dannenberg <dannenberg@ti.com> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Heiko Schocher 提交于
adding a new bootstage ID: BOOTSTAGE_ID_ENTER_CLI_LOOP Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Patrice Chotard 提交于
The objective is to provide a simple way to retrieve a BMP file, and display it as splashscreen, from extlinux.conf file input. For this, we take example on https://www.syslinux.org/wiki/ index.php?title=Menu#The_advanced_menu_system and more particularly on MENU BACKGROUND chapter. For this, add "menu background" support in pxe command. As example, extlinux.conf content will look like: # Generic Distro Configuration file generated by OpenEmbedded menu title Select the boot mode TIMEOUT 20 menu background ../splash.bmp DEFAULT stm32mp157c-ev1-sdcard LABEL stm32mp157c-ev1-sdcard KERNEL /uImage FDT /stm32mp157c-ev1.dtb APPEND root=/dev/mmcblk0p6 rootwait rw earlyprintk console=ttySTM0,115200 Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Pierre Bourdon 提交于
Fixes building mkimage on systems where OpenSSL header files do not live in the standard include path. Signed-off-by: NPierre Bourdon <delroth@gmail.com>
-
由 Heinrich Schuchardt 提交于
%g/rathen then/rather than/ Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Hannes Schmelzer 提交于
The handling of regarding bootmode and early setup has been moved to central location 'common/br_resetc.c', so use this on brxre1 board. Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>
-
由 Hannes Schmelzer 提交于
- fixup coding style - drop unused 'PUSH_KEY' define Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>
-
由 Hannes Schmelzer 提交于
On many B&R boards we have a reset-controller, responsible for very early board-bringup (voltages, clocks, ...) and bootmode selection. To be ready for adding more B&R boards to source tree while avoiding duplicate code, we add the resetcontroller implementation to the common part of B&R boards. Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>
-
由 Hannes Schmelzer 提交于
Many B&R boards are equipped with an I2C-EEPROM where various information can be stored. Today there is only a single byte for 'board_id' used. We write this 'board_id' into environment for later use during boot. If the value != 0xFF, meaning the byte is programmed, we modify the "brdefaultip" environment variable for setting an IP-Address based on board_id. Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>
-
由 Hannes Schmelzer 提交于
Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>
-
由 Hannes Schmelzer 提交于
Today the BuR common stuff is only used on AM33XX boards. In future we plan to have many other platforms than AM33XX so we have to move arch- specific #include(s) to responsible #ifdef sections. By the way we drop unneeded #include(s). Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>
-
git://git.denx.de/u-boot-marvell由 Tom Rini 提交于
- Add DM based generic watchdog start and reset implementation and remove all ad-hoc implementations (Stefan) - Move mv_sdhci to DM (Pierre) - Misc turris_omnia updates (Pierre) - Change openrd targets to correctly build again (size changes and fixes to the dts targets) and bring it back into Travis builds (Stefan) - Add Kirkwood db-88f6281-bp board (Chris)
-
-
- 26 4月, 2019 12 次提交
-
-
由 Stefan Roese 提交于
With the latest size increase of the openrd boards, they all compile clean again. Let's mark them as maintained again and add the Travis job. Please note that I can only compile-test these targets as I don't have access to one of those boards. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Albert ARIBAUD <albert-u-boot@aribaud.net> Cc: Vagrant Cascadian <vagrant@debian.org> Cc: Chris Packham <judge.packham@gmail.com> Cc: Tom Rini <trini@konsulko.com>
-
由 Stefan Roese 提交于
With the new generic function, the scattered other functions are now removed to be replaced by the generic one. The new version also enables the configuration of the watchdog timeout via the DT "timeout-sec" property (if enabled via CONFIG_OF_CONTROL). The watchdog servicing is enabled via CONFIG_WATCHDOG. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com>
-
由 Stefan Roese 提交于
With the generic watchdog driver now implemented, this patch removes some legacy stuff from the MPC8xx watchdog driver and its Kconfig integration. CONFIG_MPC8xx_WATCHDOG is completely removed and hw_watchdog_reset() is made static, as the watchdog will now get serviced via the DM infrastructure if enabled via CONFIG_WATCHDOG. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Christophe Leroy <christophe.leroy@c-s.fr>
-
由 Stefan Roese 提交于
Now that we have a generic DT property "timeout-sec" handling, the driver specific implementation can be dropped. This patch also changes the timeout restriction to the min and max values (clipping). Before this patch, the value provided via "timeout-sec" was used if the parameter was too high or low. Now the driver specific min and max values are used instead. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Michal Simek <michal.simek@xilinx.com> Reviewed-by: NMichal Simek <michal.simek@xilinx.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
-
由 Stefan Roese 提交于
This patch tries to implement a generic watchdog_reset() function that can be used by all boards that want to service the watchdog device in U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG. Without this approach, new boards or platforms needed to implement a board specific version of this functionality, mostly copy'ing the same code over and over again into their board or platforms code base. With this new generic function, the scattered other functions are now removed to be replaced by the generic one. The new version also enables the configuration of the watchdog timeout via the DT "timeout-sec" property (if enabled via CONFIG_OF_CONTROL). This patch also adds a new flag to the GD flags, to flag that the watchdog is ready to use and adds the pointer to the watchdog device to the GD. This enables us to remove the global "watchdog_dev" variable, which was prone to cause problems because of its potentially very early use in watchdog_reset(), even before the BSS is cleared. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Marek Behún" <marek.behun@nic.cz> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Maxim Sloyko <maxims@google.com> Cc: Erik van Luijk <evanluijk@interact.nl> Cc: Ryder Lee <ryder.lee@mediatek.com> Cc: Weijie Gao <weijie.gao@mediatek.com> Cc: Simon Glass <sjg@chromium.org> Cc: "Álvaro Fernández Rojas" <noltari@gmail.com> Cc: Philippe Reynes <philippe.reynes@softathome.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: NMichal Simek <michal.simek@xilinx.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
-
由 Stefan Roese 提交于
With the latest changes to the drivers (SPI_FLASH_SPANSION etc), Travis reports that the SPL image is too big. Let's use the thumb instructions in SPL to save some space and make the image fit again. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Marek Behun <marek.behun@nic.cz> Reviewed-by: NMarek Behún <marek.behun@nic.cz>
-
由 Chris Packham 提交于
Switch to the driver model for USB on the db-88f6281-bp board. CONFIG_BLK can't be enabled yet because mvebu_mmc.c needs converting. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NStefan Roese <sr@denx.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Chris Packham 提交于
This is Marvell's Kirkwood development board. It has the following features - 512M DDR2 - 2 PCI connectors - 1 x1 PCI-e interface - 1 Gigabit Ethernet Port - 2 SATA Ports - USB 2.0 Interface - SDIO - 128M NAND Flash - 16M SPI Flash It can be strapped to boot from SPI or NAND so there are two defconfigs (one per boot media). Signed-off-by: NChris Packham <judge.packham@gmail.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Michael Walle 提交于
The boot commands have changed in the environment. Add a note about the incompatible change and how resolve the issue in the board's README. Signed-off-by: NMichael Walle <michael@walle.cc> Reviewed-by: NStefan Roese <sr@denx.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
We have run now multiple times into size issues with the openrd board port. To finally fix this, this patch now moves the U-Boot size from 0x6.0000 to 0x8.0000, giving enough space for the next time. This also changes the environment location and potentially the MTD partitioning, but I see no better fix for now. Especially since this board does not have an active maintainer. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: NChris Packham <judge.packham@gmail.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Remove the superfluous CONFIG_ENV_ADDR definition. Its not needed as CONFIG_ENV_OFFSET is also set to the same value. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: NChris Packham <judge.packham@gmail.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
The following Kirkwood dtb build targets are currently missing: kirkwood-openrd-base.dtb kirkwood-openrd-client.dtb kirkwood-openrd-ultimate.dtb This patch adds them to the Makefile to fix the build error. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: NChris Packham <judge.packham@gmail.com> Signed-off-by: NStefan Roese <sr@denx.de>
-