When enabling PHYS_64BIT on 32-bit platforms, we get two warnings about
pointer casts in sunxi_mmc.c. Those are related to MMIO addresses, which
are always below 1GB on all Allwinner SoCs, so there is no problem with
anything having more than 32 bits.

Add the proper casts to make it compile cleanly.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>

The delay and bus-width setup are slightly different across the
Allwinner SoC generations, and we covered this so far with some
preprocessor conditionals.

Use the more readable IS_ENABLE() instead.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>

The H616 is our first supported Allwinner SoC which goes beyond the 4GB
address space "barrier", by having more than 32 address bits.

Lift the preliminary 3GB DRAM limit for the H616, and update the page
table setup on the way, to actually map that last GB as well.

As not all devices are actually capable of dealing with more than 32
bits (the DMA in the EMAC for instance), we also limit U-Boot's own
DRAM usage to 4GB on the way.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

We hardcode the pinctrl setting for the MMC controllers in boards.c,
since we need them also in the SPL, where there is no DT yet.

Add the respective setting for the H616 SoC, to enable eMMC on boards
with this SoC as well.
Also to make diagnosing this problem easier, print a warning if a board
tries to setup MMC2 pins without a respective SoC setting being defined.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan at amarulasolutions.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec at siol.net>

ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.

ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply
Signed-off-by: NYu-Tung Chang <mtwget@gmail.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

OrangePi PC2 board has DRAM with ODT, so enable it.
H5 SoC is also connected to voltage regulator. It's default value is
reasonable at reset, but might be too low when rebooting with a lower
voltage programmed. In order to avoid instability, enable driver for it
and set it to appropriate voltage.
Signed-off-by: NJernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: NAndre Przywara <andre.przywara@arm.com>
[Andre: remove original ZQ value change, adjust commit message]
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Most clock factors and dividers in the H6 PLLs use a "+1 encoding",
which we were missing on two occasions.

This fixes the MMC clock setup on the H6, which could be slightly off due
to the wrong parent frequency:
mmc 2 set mod-clk req 52000000 parent 1176000000 n 2 m 12 rate 49000000

Also the CPU frequency (PLL1) was a tad too high before.

For PLL5 (DRAM) we already accounted for this +1, but in the DRAM code
itself, not in the bit field macro. Move this there to be aligned with
what the other SoCs and other PLLs do.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NJernej Skrabec <jernej.skrabec@gmail.com>

Recent Allwinner platforms (starting with the H3) only use the MUSB
controller for peripheral mode and use HCI for host mode. As a result,
extra steps need to be taken to properly route USB signals to one or
the other. More precisely, the following is required:
* Routing the pins to either HCI/MUSB (controlled by PHY);
* Enabling USB PHY passby in HCI mode (controlled by PMU).

The current code will enable passby for each PHY and reroute PHY0 to
MUSB, which is inconsistent and results in broken USB peripheral support.

Passby on PHY0 must only be enabled when we want to use HCI. Since
host/device mode detection is not available from the PHY code and
because U-Boot does not support changing the mode dynamically anyway,
we can just mux the controller to MUSB if it is enabled and mux it to
HCI otherwise.

This fixes USB peripheral support for platforms with PHY0 dual-route,
especially H3/H5 and V3s.
Signed-off-by: NPaul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Update the H3 DT files from the Linux 5.12 release.

The changes update some boards, and don't affect U-Boot, but fix Gigabit
Ethernet when this DT is passed on to the Linux kernel.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Update the H5 DT files from the Linux 5.12 release.

The changes don't affect U-Boot at all, but fix Gigabit Ethernet when
this DT is passed on to the Linux kernel. It also introduces DVFS.

This also updates the shared sunxi-h3-h5.dtsi, but that only adds nodes
that are of no concern to U-Boot.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Update the H6 DT files from the Linux 5.12 release.

The changes are minimal (many LED node renames), but also help to enable
USB port 0 in U-Boot (later), enable the RSB device (not yet used in
U-Boot), and also introduce an MMC frequency limit.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

With the spear family of platforms gone, remove references to them from
the build jobs.
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

While this platform has not yet been converted, there is active efforts
to do so.  Keep the platform for now.

This reverts commit aa697e69.
Signed-off-by: NTom Rini <trini@konsulko.com>

- Remove a large number of platforms that did not migrate to DM_PCI or
  DM_USB by 2 years past the migration deadline and do not have a
  migration imminent.

We cannot build this without USB_GADGET_DOWNLOAD support enabled, add
the appropriate depends line.
Signed-off-by: NTom Rini <trini@konsulko.com>

If MUSB support is disabled, these parts of the code will fail to build.

Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.  As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.

Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.  As this is
also the last SPEAR3XX platform, remove that symbol as well.

Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.

Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.

Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove it

Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove it

Cc: Ajay Bhargav <contact@8051projects.net>
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove it.

This is also the last PL010_SERIAL using board, so remove those
references.

Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.

Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

As this board does not use CONFIG_OF_CONTROL and the DM_USB migration
deadline has passed, disable USB_GADGET support.

Cc: Eric Nelson <eric@nelint.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NEric Nelson <eric@nelint.com>

As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.

Cc: Eric Cooper <ecc@cmu.edu>
Signed-off-by: NTom Rini <trini@konsulko.com>

As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.

Cc: Luka Perkov <luka@openwrt.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.

Cc: Luka Perkov <luka@openwrt.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.

Cc: Dave Purdy <david.c.purdy@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.

Cc: Stefan Roese <sr@denx.de>
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not converted to DM_USB by the deadline, disable USB
support as they do not enable CONFIG_OF_CONTROL.

Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

The following boards no longer need CONFIG_DM_PCI_COMPAT enabled, so
remove that.
Signed-off-by: NTom Rini <trini@konsulko.com>

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.  As this is the last
ARCH_T4160 platform, remove that support as well.
Signed-off-by: NTom Rini <trini@konsulko.com>

These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove them.
Signed-off-by: NTom Rini <trini@konsulko.com>

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.
Signed-off-by: NTom Rini <trini@konsulko.com>

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.  As this is the last
ARCH_MPC8315 platform, remove that support as well.
Signed-off-by: NTom Rini <trini@konsulko.com>

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.  This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.

Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove them.  As this includes
the last ARCH_MPC8572 platform, remove that as well.

Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NPeter Tyser <ptyser@xes-inc.com>

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.

Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: NTom Rini <trini@konsulko.com>