Skip to content

U
U-Boot.Mirror

OS / U-Boot.Mirror

通知 1
Star 0
Fork 0
U
U-Boot.Mirror

体验新版 GitCode，发现更多精彩内容 >>

提交 66e3c64f 编写于 作者: T Tom Rini
浏览文件
操作

ppc: Remove kmcoge4 board 

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.

Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
上级 80696893
隐藏空白更改
内联 并排
Showing with 0 addition and 1297 deletion
board/keymile/Kconfig
浏览文件 @ 66e3c64f
......@@ -132,7 +132,6 @@ config SYS_IVM_EEPROM_PAGE_LEN
source "board/keymile/km83xx/Kconfig"
source "board/keymile/kmcent2/Kconfig"
source "board/keymile/kmp204x/Kconfig"
source "board/keymile/km_arm/Kconfig"
source "board/keymile/pg-wcom-ls102xa/Kconfig"
......
board/keymile/kmp204x/Kconfig 已删除 100644 → 0
浏览文件 @ 80696893
if TARGET_KMP204X
config SYS_BOARD
default "kmp204x"
config SYS_VENDOR
default "keymile"
config SYS_CONFIG_NAME
default "kmp204x"
config BOARD_SPECIFIC_OPTIONS # dummy
def_bool y
select ARCH_P2041
select FSL_DDR_INTERACTIVE
select PHYS_64BIT
imply CMD_CRAMFS
imply FS_CRAMFS
endif
board/keymile/kmp204x/MAINTAINERS 已删除 100644 → 0
浏览文件 @ 80696893
KMP204X BOARD
M: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
S: Maintained
F: board/keymile/kmp204x/
F: include/configs/kmp204x.h
F: configs/kmcoge4_defconfig
board/keymile/kmp204x/Makefile 已删除 100644 → 0
浏览文件 @ 80696893
# SPDX-License-Identifier: GPL-2.0+
#
# (C) Copyright 2001-2007
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
obj-y := kmp204x.o ddr.o eth.o tlb.o pci.o law.o ../common/common.o\
../common/ivm.o ../common/qrio.o
board/keymile/kmp204x/ddr.c 已删除 100644 → 0
浏览文件 @ 80696893
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2013 Keymile AG
* Valentin Longchamp <valentin.longchamp@keymile.com>
*
* Copyright 2009-2011 Freescale Semiconductor, Inc.
*/
#include <common.h>
#include <i2c.h>
#include <hwconfig.h>
#include <init.h>
#include <log.h>
#include <asm/global_data.h>
#include <asm/mmu.h>
#include <fsl_ddr_sdram.h>
#include <fsl_ddr_dimm_params.h>
DECLARE_GLOBAL_DATA_PTR;
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
if (ctrl_num) {
printf("Wrong parameter for controller number %d", ctrl_num);
return;
}
/* automatic calibration for nb of cycles between read and DQS pre */
popts->cpo_override = 0xFF;
/* 1/2 clk delay between wr command and data strobe */
popts->write_data_delay = 4;
/* clk lauched 1/2 applied cylcle after address command */
popts->clk_adjust = 4;
/* 1T timing: command/address held for only 1 cycle */
popts->twot_en = 0;
/* we have only one module, half str should be OK */
popts->half_strength_driver_enable = 1;
/* wrlvl values overridden as recommended by ddr init func */
popts->wrlvl_override = 1;
popts->wrlvl_sample = 0xf;
popts->wrlvl_start = 0x6;
/* Enable ZQ calibration */
popts->zq_en = 1;
/* DHC_EN =1, ODT = 75 Ohm */
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR_ODT_75ohm;
}
int dram_init(void)
{
phys_size_t dram_size = 0;
puts("Initializing with SPD\n");
dram_size = fsl_ddr_sdram();
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
dram_size *= 0x100000;
debug(" DDR: ");
gd->ram_size = dram_size;
return 0;
}
board/keymile/kmp204x/eth.c 已删除 100644 → 0
浏览文件 @ 80696893
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2013 Keymile AG
* Valentin Longchamp <valentin.longchamp@keymile.com>
*/
#include <common.h>
#include <net.h>
#include <netdev.h>
#include <fm_eth.h>
#include <fsl_mdio.h>
#include <phy.h>
int board_eth_init(struct bd_info *bis)
{
int ret = 0;
#ifdef CONFIG_FMAN_ENET
struct fsl_pq_mdio_info dtsec_mdio_info;
printf("Initializing Fman\n");
dtsec_mdio_info.regs =
(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
/* Register the real 1G MDIO bus */
fsl_pq_mdio_init(bis, &dtsec_mdio_info);
/* DTESC1/2 don't have a PHY, they are temporarily disabled
* so that u-boot doesn't try to unsuccessfuly enable them */
fm_disable_port(FM1_DTSEC1);
fm_disable_port(FM1_DTSEC2);
/*
* Program RGMII DTSEC5 (FM1 MAC5) on the EC2 physical itf
* This is the debug interface, the only one used in u-boot
*/
fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
fm_info_set_mdio(FM1_DTSEC5,
miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
ret = cpu_eth_init(bis);
/* reenable DTSEC1/2 for later (kernel) */
fm_enable_port(FM1_DTSEC1);
fm_enable_port(FM1_DTSEC2);
#endif
return ret;
}
#if defined(CONFIG_PHYLIB) && defined(CONFIG_PHY_MARVELL)
#define mv88E1118_PAGE_REG 22
int board_phy_config(struct phy_device *phydev)
{
if (phydev->addr == CONFIG_SYS_FM1_DTSEC5_PHY_ADDR) {
/* driver config is good */
if (phydev->drv->config)
phydev->drv->config(phydev);
/* but we still need to fix the LEDs */
phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0003);
phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x0840);
phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0000);
}
return 0;
}
#endif
board/keymile/kmp204x/kmp204x.c 已删除 100644 → 0
浏览文件 @ 80696893
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2013 Keymile AG
* Valentin Longchamp <valentin.longchamp@keymile.com>
*
* Copyright 2011,2012 Freescale Semiconductor, Inc.
*/
#include <common.h>
#include <command.h>
#include <env.h>
#include <fdt_support.h>
#include <image.h>
#include <init.h>
#include <netdev.h>
#include <linux/compiler.h>
#include <asm/mmu.h>
#include <asm/processor.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_law.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_portals.h>
#include <asm/fsl_liodn.h>
#include <fm_eth.h>
#include "../common/common.h"
#include "../common/qrio.h"
#include "kmp204x.h"
static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
int checkboard(void)
{
printf("Board: Keymile %s\n", CONFIG_SYS_CONFIG_NAME);
return 0;
}
#define ZL30158_RST 8
#define BFTIC4_RST 0
#define RSTRQSR1_WDT_RR 0x00200000
#define RSTRQSR1_SW_RR 0x00100000
int board_early_init_f(void)
{
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
bool cpuwd_flag = false;
/* configure mode for uP reset request */
qrio_uprstreq(UPREQ_CORE_RST);
/* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */
setbits_be32(&gur->ddrclkdr, 0x001f000f);
/* set reset reason according CPU register */
if ((gur->rstrqsr1 & (RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR)) ==
RSTRQSR1_WDT_RR)
cpuwd_flag = true;
qrio_cpuwd_flag(cpuwd_flag);
/* clear CPU bits by writing 1 */
setbits_be32(&gur->rstrqsr1, RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR);
/* set the BFTIC's prstcfg to reset at power-up and unit reset only */
qrio_prstcfg(BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST);
/* and enable WD on it */
qrio_wdmask(BFTIC4_RST, true);
/* set the ZL30138's prstcfg to reset at power-up only */
qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST);
/* and take it out of reset as soon as possible (needed for Hooper) */
qrio_prst(ZL30158_RST, false, false);
return 0;
}
int board_early_init_r(void)
{
int ret = 0;
/* Flush d-cache and invalidate i-cache of any FLASH data */
flush_dcache();
invalidate_icache();
set_liodns();
setup_qbman_portals();
ret = trigger_fpga_config();
if (ret)
printf("error triggering PCIe FPGA config\n");
/* enable the Unit LED (red) & Boot LED (on) */
qrio_set_leds();
/* enable Application Buffer */
qrio_enable_app_buffer();
return 0;
}
unsigned long get_board_sys_clk(unsigned long dummy)
{
return 66666666;
}
#define ETH_FRONT_PHY_RST 15
#define QSFP2_RST 11
#define QSFP1_RST 10
#define ZL30343_RST 9
int misc_init_f(void)
{
/* configure QRIO pis for i2c deblocking */
i2c_deblock_gpio_cfg();
/* configure the front phy's prstcfg and take it out of reset */
qrio_prstcfg(ETH_FRONT_PHY_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
qrio_prst(ETH_FRONT_PHY_RST, false, false);
/* set the ZL30343 prstcfg to reset at power-up only */
qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST);
/* and enable the WD on it */
qrio_wdmask(ZL30343_RST, true);
/* set the QSFPs' prstcfg to reset at power-up and unit rst only */
qrio_prstcfg(QSFP1_RST, PRSTCFG_POWUP_UNIT_RST);
qrio_prstcfg(QSFP2_RST, PRSTCFG_POWUP_UNIT_RST);
/* and enable the WD on them */
qrio_wdmask(QSFP1_RST, true);
qrio_wdmask(QSFP2_RST, true);
return 0;
}
#define NUM_SRDS_BANKS 2
int misc_init_r(void)
{
serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
u32 expected[NUM_SRDS_BANKS] = {SRDS_PLLCR0_RFCK_SEL_100,
SRDS_PLLCR0_RFCK_SEL_125};
unsigned int i;
/* check SERDES reference clocks */
for (i = 0; i < NUM_SRDS_BANKS; i++) {
u32 actual = in_be32(&regs->bank[i].pllcr0);
actual &= SRDS_PLLCR0_RFCK_SEL_MASK;
if (actual != expected[i]) {
printf("Warning: SERDES bank %u expects reference \
clock %sMHz, but actual is %sMHz\n", i + 1,
serdes_clock_to_string(expected[i]),
serdes_clock_to_string(actual));
}
}
ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN,
CONFIG_PIGGY_MAC_ADDRESS_OFFSET);
return 0;
}
#if defined(CONFIG_HUSH_INIT_VAR)
int hush_init_var(void)
{
ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN);
return 0;
}
#endif
#if defined(CONFIG_LAST_STAGE_INIT)
int last_stage_init(void)
{
#if defined(CONFIG_KMCOGE4)
/* on KMCOGE4, the BFTIC4 is on the LBAPP2 */
struct bfticu_iomap *bftic4 =
(struct bfticu_iomap *)CONFIG_SYS_LBAPP2_BASE;
u8 dip_switch = in_8((u8 *)&(bftic4->mswitch)) & BFTICU_DIPSWITCH_MASK;
if (dip_switch != 0) {
/* start bootloader */
puts("DIP: Enabled\n");
env_set("actual_bank", "0");
}
#endif
set_km_env();
return 0;
}
#endif
#ifdef CONFIG_SYS_DPAA_FMAN
void fdt_fixup_fman_mac_addresses(void *blob)
{
int node, i, ret;
char *tmp, *end;
unsigned char mac_addr[6];
/* get the mac addr from env */
tmp = env_get("ethaddr");
if (!tmp) {
printf("ethaddr env variable not defined\n");
return;
}
for (i = 0; i < 6; i++) {
mac_addr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0;
if (tmp)
tmp = (*end) ? end+1 : end;
}
/* find the correct fdt ethernet path and correct it */
node = fdt_path_offset(blob, "/soc/fman/ethernet@e8000");
if (node < 0) {
printf("no /soc/fman/ethernet path offset\n");
return;
}
ret = fdt_setprop(blob, node, "local-mac-address", &mac_addr, 6);
if (ret) {
printf("error setting local-mac-address property\n");
return;
}
}
#endif
int ft_board_setup(void *blob, struct bd_info *bd)
{
phys_addr_t base;
phys_size_t size;
ft_cpu_setup(blob, bd);
base = env_get_bootm_low();
size = env_get_bootm_size();
fdt_fixup_memory(blob, (u64)base, (u64)size);
#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
fsl_fdt_fixup_dr_usb(blob, bd);
#endif
#ifdef CONFIG_PCI
pci_of_setup(blob, bd);
#endif
fdt_fixup_liodn(blob);
#ifdef CONFIG_SYS_DPAA_FMAN
fdt_fixup_fman_ethernet(blob);
fdt_fixup_fman_mac_addresses(blob);
#endif
return 0;
}
#if defined(CONFIG_POST)
/* DIC26_SELFTEST GPIO used to start factory test sw */
#define SELFTEST_PORT QRIO_GPIO_A
#define SELFTEST_PIN 31
int post_hotkeys_pressed(void)
{
qrio_gpio_direction_input(SELFTEST_PORT, SELFTEST_PIN);
return qrio_get_gpio(SELFTEST_PORT, SELFTEST_PIN);
}
#endif
board/keymile/kmp204x/kmp204x.h 已删除 100644 → 0
浏览文件 @ 80696893
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2013 Keymile AG
* Valentin Longchamp <valentin.longchamp@keymile.com>
*/
void pci_of_setup(void *blob, struct bd_info *bd);
board/keymile/kmp204x/law.c 已删除 100644 → 0
浏览文件 @ 80696893
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2013 Keymile AG
* Valentin Longchamp <valentin.longchamp@keymile.com>
*
* Copyright 2008-2011 Freescale Semiconductor, Inc.
*
* (C) Copyright 2000
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*/
#include <common.h>
#include <asm/fsl_law.h>
#include <asm/mmu.h>
struct law_entry law_table[] = {
#ifdef CONFIG_SYS_BMAN_MEM_PHYS
SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN),
#endif
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN),
#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
/* Limit DCSR to 32M to access NPC Trace Buffer */
SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
#endif
#ifdef CONFIG_SYS_NAND_BASE_PHYS
SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC),
#endif
SET_LAW(CONFIG_SYS_QRIO_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC),
#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS
SET_LAW(CONFIG_SYS_LBAPP1_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
#endif
#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS
SET_LAW(CONFIG_SYS_LBAPP2_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
#endif
};
int num_law_entries = ARRAY_SIZE(law_table);
board/keymile/kmp204x/pbi.cfg 已删除 100644 → 0
浏览文件 @ 80696893
# SPDX-License-Identifier: GPL-2.0+
#
# Copyright 2012 Freescale Semiconductor, Inc.
# Refer docs/README.pblimage for more details about how-to configure
# and create PBL boot image
#
#PBI commands
#Configure ALTCBAR for DCSR -> DCSR@89000000
091380c0 000009C4
09000010 00000000
091380c0 000009C4
09000014 00000000
091380c0 000009C4
09000018 81d00000
#Workaround for A-004849
091380c0 000009C4
890B0050 00000002
091380c0 000009C4
890B0054 00000002
091380c0 000009C4
890B0058 00000002
091380c0 000009C4
890B005C 00000002
091380c0 000009C4
890B0090 00000002
091380c0 000009C4
890B0094 00000002
091380c0 000009C4
890B0098 00000002
091380c0 000009C4
890B009C 00000002
091380c0 000009C4
890B0108 00000012
091380c0 000009C4
#Workaround for A-006559 needed for rev 2.0 of P2041 silicon
89021008 0000f000
091380c0 000009C4
89021028 0000f000
091380c0 000009C4
89021048 0000f000
091380c0 000009C4
89021068 0000f000
091380c0 000009C4
#Flush PBL data
09138000 00000000
#Disable ALTCBAR
09000018 00000000
091380c0 000009C4
#Initialize CPC1 as 1MB SRAM
09010000 00200400
09138000 00000000
091380c0 00000100
09010100 00000000
09010104 fff0000b
09010f00 08000000
09010000 80000000
#Configure LAW for CPC1
09000d00 00000000
09000d04 fff00000
09000d08 81000013
09000010 00000000
09000014 ff000000
09000018 81000000
#Initialize eSPI controller, default configuration is slow for eSPI to
#load data, this configuration comes from u-boot eSPI driver.
09110000 80000403
09110020 27170008
09110024 00100008
09110028 00100008
0911002c 00100008
#Flush PBL data
09138000 00000000
091380c0 00000000
board/keymile/kmp204x/pci.c 已删除 100644 → 0
浏览文件 @ 80696893
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2013 Keymile AG
* Valentin Longchamp <valentin.longchamp@keymile.com>
*
* Copyright 2007-2011 Freescale Semiconductor, Inc.
*/
#include <common.h>
#include <command.h>
#include <init.h>
#include <pci.h>
#include <asm/fsl_pci.h>
#include <linux/delay.h>
#include <linux/libfdt.h>
#include <fdt_support.h>
#include <asm/fsl_serdes.h>
#include <linux/errno.h>
#include "../common/qrio.h"
#include "kmp204x.h"
#define PROM_SEL_L 11
/* control the PROM_SEL_L signal*/
static void toggle_fpga_eeprom_bus(bool cpu_own)
{
qrio_gpio_direction_output(QRIO_GPIO_A, PROM_SEL_L, !cpu_own);
}
#define CONF_SEL_L 10
#define FPGA_PROG_L 19
#define FPGA_DONE 18
#define FPGA_INIT_L 17
int trigger_fpga_config(void)
{
int ret = 0, init_l;
/* approx 10ms */
u32 timeout = 10000;
/* make sure the FPGA_can access the EEPROM */
toggle_fpga_eeprom_bus(false);
/* assert CONF_SEL_L to be able to drive FPGA_PROG_L */
qrio_gpio_direction_output(QRIO_GPIO_A, CONF_SEL_L, 0);
/* trigger the config start */
qrio_gpio_direction_output(QRIO_GPIO_A, FPGA_PROG_L, 0);
/* small delay for INIT_L line */
udelay(10);
/* wait for FPGA_INIT to be asserted */
do {
init_l = qrio_get_gpio(QRIO_GPIO_A, FPGA_INIT_L);
if (timeout-- == 0) {
printf("FPGA_INIT timeout\n");
ret = -EFAULT;
break;
}
udelay(10);
} while (init_l);
/* deassert FPGA_PROG, config should start */
qrio_set_gpio(QRIO_GPIO_A, FPGA_PROG_L, 1);
return ret;
}
/* poll the FPGA_DONE signal and give the EEPROM back to the QorIQ */
static int wait_for_fpga_config(void)
{
int ret = 0, done;
/* approx 5 s */
u32 timeout = 500000;
printf("PCIe FPGA config:");
do {
done = qrio_get_gpio(QRIO_GPIO_A, FPGA_DONE);
if (timeout-- == 0) {
printf(" FPGA_DONE timeout\n");
ret = -EFAULT;
goto err_out;
}
udelay(10);
} while (!done);
printf(" done\n");
err_out:
/* deactive CONF_SEL and give the CPU conf EEPROM access */
qrio_set_gpio(QRIO_GPIO_A, CONF_SEL_L, 1);
toggle_fpga_eeprom_bus(true);
return ret;
}
#define PCIE_SW_RST 14
#define PEXHC_RST 13
#define HOOPER_RST 12
void pci_init_board(void)
{
qrio_prstcfg(PCIE_SW_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
qrio_prstcfg(PEXHC_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
qrio_prstcfg(HOOPER_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
/* wait for the PCIe FPGA to be configured
* it has been triggered earlier in board_early_init_r */
if (wait_for_fpga_config())
printf("error finishing PCIe FPGA config\n");
qrio_prst(PCIE_SW_RST, false, false);
qrio_prst(PEXHC_RST, false, false);
qrio_prst(HOOPER_RST, false, false);
/* Hooper is not direcly PCIe capable */
mdelay(50);
fsl_pcie_init_board(0);
}
void pci_of_setup(void *blob, struct bd_info *bd)
{
FT_FSL_PCI_SETUP;
}
board/keymile/kmp204x/rcw_kmp204x.cfg 已删除 100644 → 0
浏览文件 @ 80696893
#
# Default RCW for kmp204x boards
#
#PBL preamble and RCW header
aa55aa55 010e0100
#64 bytes RCW data
14600000 00000000 28200000 00000000
148E70CF CFC02000 58000000 41000000
00000000 00000000 00000000 F0428816
00000000 00000000 00000000 00000000
board/keymile/kmp204x/tlb.c 已删除 100644 → 0
浏览文件 @ 80696893
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2013 Keymile AG
* Valentin Longchamp <valentin.longchamp@keymile.com>
*
* Copyright 2008-2011 Freescale Semiconductor, Inc.
*
* (C) Copyright 2000
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*/
#include <common.h>
#include <asm/mmu.h>
struct fsl_e_tlb_entry tlb_table[] = {
/* TLB 0 - for temp stack in cache */
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
CONFIG_SYS_INIT_RAM_ADDR_PHYS,
MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
/* TLB 1 */
/* *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
* SRAM is at 0xfff00000, it covered the 0xfffff000.
*/
SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 0, BOOKE_PAGESZ_1M, 1),
/* *I*G* - CCSRBAR */
SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 1, BOOKE_PAGESZ_16M, 1),
/* QRIO */
SET_TLB_ENTRY(1, CONFIG_SYS_QRIO_BASE, CONFIG_SYS_QRIO_BASE_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 2, BOOKE_PAGESZ_64K, 1),
/* *I*G* - PCI1 */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 3, BOOKE_PAGESZ_512M, 1),
/* *I*G* - PCI3 */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 4, BOOKE_PAGESZ_512M, 1),
/* *I*G* - PCI1&3 I/O */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 6, BOOKE_PAGESZ_128K, 1),
#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS
/* LBAPP1 */
SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP1_BASE, CONFIG_SYS_LBAPP1_BASE_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 7, BOOKE_PAGESZ_256M, 1),
#endif
#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS
/* LBAPP2 */
SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP2_BASE, CONFIG_SYS_LBAPP2_BASE_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 8, BOOKE_PAGESZ_256M, 1),
#endif
/* Bman/Qman */
#ifdef CONFIG_SYS_BMAN_MEM_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
MAS3_SW|MAS3_SR, 0,
0, 9, BOOKE_PAGESZ_1M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 10, BOOKE_PAGESZ_1M, 1),
#endif
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
MAS3_SW|MAS3_SR, 0,
0, 11, BOOKE_PAGESZ_1M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 12, BOOKE_PAGESZ_1M, 1),
#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 13, BOOKE_PAGESZ_4M, 1),
#endif
#ifdef CONFIG_SYS_NAND_BASE
/*
* *I*G - NAND
* entry 14 and 15 has been used hard coded, they will be disabled
* in cpu_init_f, so we use entry 16 for nand.
*/
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 16, BOOKE_PAGESZ_32K, 1),
#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
configs/kmcoge4_defconfig 已删除 100644 → 0
浏览文件 @ 80696893
CONFIG_PPC=y
CONFIG_SYS_TEXT_BASE=0xfff40000
CONFIG_ENV_SIZE=0x4000
CONFIG_ENV_OFFSET=0x100000
CONFIG_ENV_SECT_SIZE=0x10000
CONFIG_BOOTCOUNT_BOOTLIMIT=3
CONFIG_SYS_BOOTCOUNT_ADDR=0xFB000020
CONFIG_ENV_OFFSET_REDUND=0x110000
CONFIG_MPC85xx=y
CONFIG_TARGET_KMP204X=y
# CONFIG_SYS_MALLOC_F is not set
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_SYS_EXTRA_OPTIONS="KMCOGE4"
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_BOARD_EARLY_INIT_R=y
CONFIG_LAST_STAGE_INIT=y
CONFIG_MISC_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_CMD_GREPENV=y
CONFIG_CMD_EEPROM=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_I2C=y
CONFIG_CMD_SF=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_MP=y
# CONFIG_CMD_HASH is not set
CONFIG_CMD_JFFS2=y
CONFIG_CMD_MTDPARTS=y
CONFIG_MTDIDS_DEFAULT="nand0=fsl_elbc_nand"
CONFIG_MTDPARTS_DEFAULT="mtdparts=fsl_elbc_nand:-(ubi0);"
# CONFIG_CMD_IRQ is not set
CONFIG_CMD_UBI=y
# CONFIG_CMD_UBIFS is not set
CONFIG_DOS_PARTITION=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
CONFIG_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
# CONFIG_MMC is not set
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
CONFIG_PHYLIB_10G=y
CONFIG_PHY_MARVELL=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
CONFIG_FMAN_ENET=y
CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_FSL_ESPI=y
CONFIG_ADDR_MAP=y
CONFIG_SYS_NUM_ADDR_MAP=64
CONFIG_BCH=y
CONFIG_OF_LIBFDT=y
include/configs/kmp204x.h 已删除 100644 → 0
浏览文件 @ 80696893
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2013 Keymile AG
* Valentin Longchamp <valentin.longchamp@keymile.com>
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#if defined(CONFIG_KMCOGE4)
#define CONFIG_HOSTNAME "kmcoge4"
#else
#error ("Board not supported")
#endif
#define CONFIG_KMP204X
/* an additionnal option is required for UBI as subpage access is
* supported in u-boot
*/
#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048"
#define CONFIG_NAND_ECC_BCH
/* common KM defines */
#include "km/keymile-common.h"
#define CONFIG_SYS_RAMBOOT
#define CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
/* High Level Configuration Options */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_PCIE3 /* PCIE controller 3 */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_SYS_DPAA_RMAN /* RMan */
/* Environment in SPI Flash */
#define CONFIG_ENV_TOTAL_SIZE 0x020000
#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(unsigned long dummy);
#endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BACKSIDE_L2_CACHE
#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */
/*
* Config the L3 Cache as L3 SRAM
*/
#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \
CONFIG_RAMBOOT_TEXT_BASE)
#define CONFIG_SYS_L3_SIZE (1024 << 10)
#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
/*
* DDR Setup
*/
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x54
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
/******************************************************************************
* (PRAM usage)
* ... -------------------------------------------------------
* ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
* ... |<------------------- pram -------------------------->|
* ... -------------------------------------------------------
* @END_OF_RAM:
* @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
* @CONFIG_KM_PHRAM: address for /var
* @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
* @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
*/
/* size of rootfs in RAM */
#define CONFIG_KM_ROOTFSSIZE 0x0
/* pseudo-non volatile RAM [hex] */
#define CONFIG_KM_PNVRAM 0x80000
/* physical RAM MTD size [hex] */
#define CONFIG_KM_PHRAM 0x100000
/* reserved pram area at the end of memory [hex]
* u-boot reserves some memory for the MP boot page
*/
#define CONFIG_KM_RESERVED_PRAM 0x1000
/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
* is not valid yet, which is the case for when u-boot copies itself to RAM
*/
#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM) >> 10)
/*
* Local Bus Definitions
*/
/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2)
/* Nand Flash */
#define CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_NAND_BASE 0xffa00000
#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
/* NAND flash config */
#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| BR_PS_8 /* Port Size = 8 bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
| OR_FCM_BCTLD /* LBCTL not ass */ \
| OR_FCM_SCY_1 /* 1 clk wait cycle */ \
| OR_FCM_RST /* 1 clk read setup */ \
| OR_FCM_PGS /* Large page size */ \
| OR_FCM_CST) /* 0.25 command setup */
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
/* QRIO FPGA */
#define CONFIG_SYS_QRIO_BASE 0xfb000000
#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull
#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
| BR_PS_8 /* Port Size 8 bits */ \
| BR_DECC_OFF /* no error corr */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \
| OR_GPCM_BCTLD /* no LCTL assert */ \
| OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
| OR_GPCM_TRLX /* relaxed tmgs */ \
| OR_GPCM_EAD) /* extra bus clk cycles */
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
#define CONFIG_HWCONFIG
/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x11C500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x11C600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR + 0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR + 0x11D600)
#define CONFIG_KM_CONSOLE_TTY "ttyS0"
/* I2C */
/* QRIO GPIOs used for deblocking */
#define KM_I2C_DEBLOCK_PORT QRIO_GPIO_A
#define KM_I2C_DEBLOCK_SCL 20
#define KM_I2C_DEBLOCK_SDA 21
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_INIT_BOARD
#define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */
#define CONFIG_SYS_NUM_I2C_BUSES 3
#define CONFIG_SYS_I2C_MAX_HOPS 1
#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
{0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
}
#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/
/*
* eSPI - Enhanced SPI
*/
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
/* Qman/Bman */
#define CONFIG_SYS_BMAN_NUM_PORTALS 10
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
CONFIG_SYS_BMAN_CENA_SIZE)
#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_QMAN_NUM_PORTALS 10
#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
CONFIG_SYS_QMAN_CENA_SIZE)
#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
/* Default address of microcode for the Linux Fman driver
* env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
* ucode is stored after env, so we got 0x120000.
*/
#define CONFIG_SYS_FMAN_FW_ADDR 0x120000
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
/* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */
#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11
#define CONFIG_SYS_TBIPA_VALUE 8
#define CONFIG_ETHPRIME "FM1@DTSEC5"
/*
* Environment
*/
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
* Hardware Watchdog
*/
#define CONFIG_WATCHDOG /* enable CPU watchdog */
#define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */
#define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */
/*
* additionnal command line configuration.
*/
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
#define __USB_PHY_TYPE utmi
#define CONFIG_USB_EHCI_FSL
/*
* Environment Configuration
*/
#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
#define CONFIG_KM_DEF_ENV "km-common=empty\0"
#endif
/* architecture specific default bootargs */
#define CONFIG_KM_DEF_BOOT_ARGS_CPU ""
/* FIXME: FDT_ADDR is unspecified */
#define CONFIG_KM_DEF_ENV_CPU \
"boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \
"cramfsloadfdt=" \
"cramfsload ${fdt_addr_r} " \
"fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \
"fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \
"u-boot=" CONFIG_HOSTNAME "/u-boot.pbl\0" \
"update=" \
"sf probe 0;sf erase 0 +${filesize};" \
"sf write ${load_addr_r} 0 ${filesize};\0" \
"set_fdthigh=true\0" \
"checkfdt=true\0" \
""
#define CONFIG_HW_ENV_SETTINGS \
"hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \
"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
"usb_dr_mode=host\0"
#define CONFIG_KM_NEW_ENV \
"newenv=sf probe 0;" \
"sf erase " __stringify(CONFIG_ENV_OFFSET) " " \
__stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
#ifndef CONFIG_KM_DEF_ARCH
#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_KM_DEF_ENV \
CONFIG_KM_DEF_ARCH \
CONFIG_KM_NEW_ENV \
CONFIG_HW_ENV_SETTINGS \
"EEprom_ivm=pca9547:70:9\0" \
""
/* App2 Local bus */
#define CONFIG_SYS_LBAPP2_BASE 0xE0000000
#define CONFIG_SYS_LBAPP2_BASE_PHYS 0xFE0000000ull
#define CONFIG_SYS_LBAPP2_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP2_BASE_PHYS) \
| BR_PS_8 /* Port Size 8 bits */ \
| BR_DECC_OFF /* no error corr */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_LBAPP2_OR_PRELIM (OR_AM_256MB /* length 256MB */ \
| OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \
| OR_GPCM_CSNT /* LCS 1/4 clk before */ \
| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
| OR_GPCM_TRLX /* relaxed tmgs */ \
| OR_GPCM_EAD) /* extra bus clk cycles */
/* Local bus app2 Base Address */
#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_LBAPP2_BR_PRELIM
/* Local bus app2 Options */
#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_LBAPP2_OR_PRELIM
#endif /* __CONFIG_H */
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或