- 10 7月, 2021 7 次提交
-
-
由 Yu-Tung Chang 提交于
ZeroPi is a new board of high performance with low cost designed by FriendlyElec., using the Allwinner H3 SOC. ZeroPi features - Allwinner H3, Quad-core Cortex-A7@1.2GHz - 256MB/512MB DDR3 RAM - microsd slot - 10/100/1000Mbps Ethernet - Debug Serial Port - DC 5V/2A power-supply Signed-off-by: NYu-Tung Chang <mtwget@gmail.com> Reviewed-by: NAndre Przywara <andre.przywara@arm.com> Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Jernej Skrabec 提交于
OrangePi PC2 board has DRAM with ODT, so enable it. H5 SoC is also connected to voltage regulator. It's default value is reasonable at reset, but might be too low when rebooting with a lower voltage programmed. In order to avoid instability, enable driver for it and set it to appropriate voltage. Signed-off-by: NJernej Skrabec <jernej.skrabec@gmail.com> Tested-by: NAndre Przywara <andre.przywara@arm.com> [Andre: remove original ZQ value change, adjust commit message] Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
Most clock factors and dividers in the H6 PLLs use a "+1 encoding", which we were missing on two occasions. This fixes the MMC clock setup on the H6, which could be slightly off due to the wrong parent frequency: mmc 2 set mod-clk req 52000000 parent 1176000000 n 2 m 12 rate 49000000 Also the CPU frequency (PLL1) was a tad too high before. For PLL5 (DRAM) we already accounted for this +1, but in the DRAM code itself, not in the bit field macro. Move this there to be aligned with what the other SoCs and other PLLs do. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NJernej Skrabec <jernej.skrabec@gmail.com>
-
由 Paul Kocialkowski 提交于
Recent Allwinner platforms (starting with the H3) only use the MUSB controller for peripheral mode and use HCI for host mode. As a result, extra steps need to be taken to properly route USB signals to one or the other. More precisely, the following is required: * Routing the pins to either HCI/MUSB (controlled by PHY); * Enabling USB PHY passby in HCI mode (controlled by PMU). The current code will enable passby for each PHY and reroute PHY0 to MUSB, which is inconsistent and results in broken USB peripheral support. Passby on PHY0 must only be enabled when we want to use HCI. Since host/device mode detection is not available from the PHY code and because U-Boot does not support changing the mode dynamically anyway, we can just mux the controller to MUSB if it is enabled and mux it to HCI otherwise. This fixes USB peripheral support for platforms with PHY0 dual-route, especially H3/H5 and V3s. Signed-off-by: NPaul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
Update the H3 DT files from the Linux 5.12 release. The changes update some boards, and don't affect U-Boot, but fix Gigabit Ethernet when this DT is passed on to the Linux kernel. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
Update the H5 DT files from the Linux 5.12 release. The changes don't affect U-Boot at all, but fix Gigabit Ethernet when this DT is passed on to the Linux kernel. It also introduces DVFS. This also updates the shared sunxi-h3-h5.dtsi, but that only adds nodes that are of no concern to U-Boot. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Andre Przywara 提交于
Update the H6 DT files from the Linux 5.12 release. The changes are minimal (many LED node renames), but also help to enable USB port 0 in U-Boot (later), enable the RSB device (not yet used in U-Boot), and also introduce an MMC frequency limit. Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
-
- 08 7月, 2021 33 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
With the spear family of platforms gone, remove references to them from the build jobs. Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
While this platform has not yet been converted, there is active efforts to do so. Keep the platform for now. This reverts commit aa697e69. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
- Remove a large number of platforms that did not migrate to DM_PCI or DM_USB by 2 years past the migration deadline and do not have a migration imminent.
-
由 Tom Rini 提交于
We cannot build this without USB_GADGET_DOWNLOAD support enabled, add the appropriate depends line. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
If MUSB support is disabled, these parts of the code will fail to build. Cc: Paul Kocialkowski <contact@paulk.fr> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove them. As this is the last of the SPEAr platforms, so remove the rest of the remaining support as well. Cc: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove them. As this is also the last SPEAR3XX platform, remove that symbol as well. Cc: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove them. Cc: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove them. Cc: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove it Cc: Gerald Kerma <dreagle@doukki.net> Cc: Tony Dinh <mibodhi@gmail.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove it Cc: Ajay Bhargav <contact@8051projects.net> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove it. This is also the last PL010_SERIAL using board, so remove those references. Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove them. Cc: Andreas Bießmann <andreas@biessmann.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
As this board does not use CONFIG_OF_CONTROL and the DM_USB migration deadline has passed, disable USB_GADGET support. Cc: Eric Nelson <eric@nelint.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NEric Nelson <eric@nelint.com>
-
由 Tom Rini 提交于
As these boards support CONFIG_OF_CONTROL today, perform a basic CONFIG_DM migration. Cc: Eric Cooper <ecc@cmu.edu> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
As these boards support CONFIG_OF_CONTROL today, perform a basic CONFIG_DM migration. Cc: Luka Perkov <luka@openwrt.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
As these boards support CONFIG_OF_CONTROL today, perform a basic CONFIG_DM migration. Cc: Luka Perkov <luka@openwrt.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
As these boards support CONFIG_OF_CONTROL today, perform a basic CONFIG_DM migration. Cc: Dave Purdy <david.c.purdy@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
As these boards support CONFIG_OF_CONTROL today, perform a basic CONFIG_DM migration. Cc: Stefan Roese <sr@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not converted to DM_USB by the deadline, disable USB support as they do not enable CONFIG_OF_CONTROL. Cc: Simon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
The following boards no longer need CONFIG_DM_PCI_COMPAT enabled, so remove that. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This board has not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove it. As this is the last ARCH_T4160 platform, remove that support as well. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove them. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This board has not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove it. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This board has not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove it. As this is the last ARCH_MPC8315 platform, remove that support as well. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This board has not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove it. This is also the last of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well. Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove them. As this includes the last ARCH_MPC8572 platform, remove that as well. Cc: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NPeter Tyser <ptyser@xes-inc.com>
-
由 Tom Rini 提交于
This board has not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove it. Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This board has not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove it. As this is the last ARCH_MPC8568 platform, remove that support as well. Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove them. As this is the only ARCH_T1023 platform left, remove that support as well. Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
These boards have not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove them. As this is the only ARCH_MPC8555 platform left, remove that support as well. Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This board has not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove it. As this is the only MPC8541 target left, remove that architecture support as well. Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-