Kconfig 57.6 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3
config MIPS
	bool
	default y
4
	select HAVE_GENERIC_DMA_COHERENT
S
Sam Ravnborg 已提交
5
	select HAVE_IDE
M
Mathieu Desnoyers 已提交
6
	select HAVE_OPROFILE
7 8
	select HAVE_PERF_EVENTS
	select PERF_USE_VMALLOC
9
	select HAVE_ARCH_KGDB
10
	select HAVE_FUNCTION_TRACER
11
	select HAVE_FUNCTION_TRACE_MCOUNT_TEST
12 13
	select HAVE_DYNAMIC_FTRACE
	select HAVE_FTRACE_MCOUNT_RECORD
14
	select HAVE_C_RECORDMCOUNT
15
	select HAVE_FUNCTION_GRAPH_TRACER
D
David Daney 已提交
16 17
	select HAVE_KPROBES
	select HAVE_KRETPROBES
18
	select RTC_LIB if !MACH_LOONGSON
19
	select GENERIC_ATOMIC64 if !64BIT
20 21
	select HAVE_DMA_ATTRS
	select HAVE_DMA_API_DEBUG
22 23
	select HAVE_GENERIC_HARDIRQS
	select GENERIC_IRQ_PROBE
24
	select HAVE_ARCH_JUMP_LABEL
L
Linus Torvalds 已提交
25 26 27

menu "Machine selection"

28 29 30
config ZONE_DMA
	bool

31 32 33
choice
	prompt "System type"
	default SGI_IP22
L
Linus Torvalds 已提交
34

35
config MIPS_ALCHEMY
36
	bool "Alchemy processor based machines"
37 38 39 40 41 42 43 44 45
	select 64BIT_PHYS_ADDR
	select CEVT_R4K_LIB
	select CSRC_R4K_LIB
	select IRQ_CPU
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_APM_EMULATION
	select GENERIC_GPIO
	select ARCH_WANT_OPTIONAL_GPIOLIB
46
	select SYS_SUPPORTS_ZBOOT
L
Linus Torvalds 已提交
47

48 49 50 51 52 53 54 55 56 57 58 59 60
config AR7
	bool "Texas Instruments AR7"
	select BOOT_ELF32
	select DMA_NONCOHERENT
	select CEVT_R4K
	select CSRC_R4K
	select IRQ_CPU
	select NO_EXCEPT_FILL
	select SWAP_IO_SPACE
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_EARLY_PRINTK
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
61
	select SYS_SUPPORTS_ZBOOT_UART16550
F
Florian Fainelli 已提交
62
	select ARCH_REQUIRE_GPIOLIB
63 64 65 66 67 68
	select GCD
	select VLYNQ
	help
	  Support for the Texas Instruments AR7 System-on-a-Chip
	  family: TNETD7100, 7200 and 7300.

69 70
config ATH79
	bool "Atheros AR71XX/AR724X/AR913X based boards"
G
Gabor Juhos 已提交
71
	select ARCH_REQUIRE_GPIOLIB
72 73 74 75 76
	select BOOT_RAW
	select CEVT_R4K
	select CSRC_R4K
	select DMA_NONCOHERENT
	select IRQ_CPU
77
	select MIPS_MACHINE
78 79 80 81 82 83 84
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_HAS_EARLY_PRINTK
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	help
	  Support for the Atheros AR71XX/AR724X/AR913X SoCs.

85
config BCM47XX
86
	bool "Broadcom BCM47XX based boards"
87
	select CEVT_R4K
88
	select CSRC_R4K
89 90 91 92 93 94 95 96
	select DMA_NONCOHERENT
	select HW_HAS_PCI
	select IRQ_CPU
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
	select SSB
	select SSB_DRIVER_MIPS
97
	select SSB_DRIVER_EXTIF
98
	select SSB_EMBEDDED
99
	select SSB_B43_PCI_BRIDGE if PCI
100
	select SSB_PCICORE_HOSTMODE if PCI
101
	select GENERIC_GPIO
A
Aurelien Jarno 已提交
102 103
	select SYS_HAS_EARLY_PRINTK
	select CFE
104 105 106
	help
	 Support for BCM47XX based boards

107 108 109 110 111 112 113 114 115 116 117 118 119 120 121
config BCM63XX
	bool "Broadcom BCM63XX based boards"
	select CEVT_R4K
	select CSRC_R4K
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_HAS_EARLY_PRINTK
	select SWAP_IO_SPACE
	select ARCH_REQUIRE_GPIOLIB
	help
	 Support for BCM63XX based boards

L
Linus Torvalds 已提交
122
config MIPS_COBALT
123
	bool "Cobalt Server"
124
	select CEVT_R4K
125
	select CSRC_R4K
126
	select CEVT_GT641XX
L
Linus Torvalds 已提交
127 128
	select DMA_NONCOHERENT
	select HW_HAS_PCI
129
	select I8253
L
Linus Torvalds 已提交
130 131
	select I8259
	select IRQ_CPU
Y
Yoichi Yuasa 已提交
132
	select IRQ_GT641XX
133
	select PCI_GT64XXX_PCI0
134
	select PCI
135
	select SYS_HAS_CPU_NEVADA
Y
Yoichi Yuasa 已提交
136
	select SYS_HAS_EARLY_PRINTK
137
	select SYS_SUPPORTS_32BIT_KERNEL
138
	select SYS_SUPPORTS_64BIT_KERNEL
139
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
140 141

config MACH_DECSTATION
142
	bool "DECstations"
L
Linus Torvalds 已提交
143
	select BOOT_ELF32
144
	select CEVT_DS1287
145
	select CEVT_R4K
146
	select CSRC_IOASIC
147
	select CSRC_R4K
148 149 150
	select CPU_DADDI_WORKAROUNDS if 64BIT
	select CPU_R4000_WORKAROUNDS if 64BIT
	select CPU_R4400_WORKAROUNDS if 64BIT
L
Linus Torvalds 已提交
151
	select DMA_NONCOHERENT
152
	select NO_IOPORT
L
Linus Torvalds 已提交
153
	select IRQ_CPU
154 155
	select SYS_HAS_CPU_R3000
	select SYS_HAS_CPU_R4X00
156 157
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
158
	select SYS_SUPPORTS_LITTLE_ENDIAN
159 160 161
	select SYS_SUPPORTS_128HZ
	select SYS_SUPPORTS_256HZ
	select SYS_SUPPORTS_1024HZ
162
	help
L
Linus Torvalds 已提交
163 164 165 166 167 168 169
	  This enables support for DEC's MIPS based workstations.  For details
	  see the Linux/MIPS FAQ on <http://www.linux-mips.org/> and the
	  DECstation porting pages on <http://decstation.unix-ag.org/>.

	  If you have one of the following DECstation Models you definitely
	  want to choose R4xx0 for the CPU Type:

170 171 172 173
		DECstation 5000/50
		DECstation 5000/150
		DECstation 5000/260
		DECsystem 5900/260
L
Linus Torvalds 已提交
174 175 176

	  otherwise choose R3000.

177
config MACH_JAZZ
178
	bool "Jazz family of machines"
179 180 181
	select ARC
	select ARC32
	select ARCH_MAY_HAVE_PC_FDC
182
	select CEVT_R4K
183
	select CSRC_R4K
T
Thomas Bogendoerfer 已提交
184
	select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
185
	select GENERIC_ISA_DMA
T
Thomas Bogendoerfer 已提交
186
	select IRQ_CPU
187
	select I8253
188 189
	select I8259
	select ISA
190
	select SYS_HAS_CPU_R4X00
191 192
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
193
	select SYS_SUPPORTS_100HZ
L
Linus Torvalds 已提交
194
	help
195 196
	 This a family of machines based on the MIPS R4030 chipset which was
	 used by several vendors to build RISC/os and Windows NT workstations.
197
	 Members include the Acer PICA, MIPS Magnum 4000, MIPS Millennium and
198 199
	 Olivetti M700-10 workstations.

200 201 202 203 204 205 206 207 208 209 210 211
config MACH_JZ4740
	bool "Ingenic JZ4740 based machines"
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
	select DMA_NONCOHERENT
	select IRQ_CPU
	select GENERIC_GPIO
	select ARCH_REQUIRE_GPIOLIB
	select SYS_HAS_EARLY_PRINTK
	select HAVE_PWM

212 213
config LASAT
	bool "LASAT Networks platforms"
214
	select CEVT_R4K
215
	select CSRC_R4K
216 217 218
	select DMA_NONCOHERENT
	select SYS_HAS_EARLY_PRINTK
	select HW_HAS_PCI
219
	select IRQ_CPU
220 221 222 223 224 225 226 227
	select PCI_GT64XXX_PCI0
	select MIPS_NILE4
	select R5000_CPU_SCACHE
	select SYS_HAS_CPU_R5000
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL if BROKEN
	select SYS_SUPPORTS_LITTLE_ENDIAN

228 229
config MACH_LOONGSON
	bool "Loongson family of machines"
230
	select SYS_SUPPORTS_ZBOOT
231
	help
232 233 234 235 236 237
	  This enables the support of Loongson family of machines.

	  Loongson is a family of general-purpose MIPS-compatible CPUs.
	  developed at Institute of Computing Technology (ICT),
	  Chinese Academy of Sciences (CAS) in the People's Republic
	  of China. The chief architect is Professor Weiwu Hu.
238

L
Linus Torvalds 已提交
239
config MIPS_MALTA
240
	bool "MIPS Malta board"
241
	select ARCH_MAY_HAVE_PC_FDC
L
Linus Torvalds 已提交
242
	select BOOT_ELF32
243
	select BOOT_RAW
244
	select CEVT_R4K
245
	select CSRC_R4K
L
Linus Torvalds 已提交
246 247
	select DMA_NONCOHERENT
	select GENERIC_ISA_DMA
248
	select IRQ_CPU
249
	select IRQ_GIC
L
Linus Torvalds 已提交
250
	select HW_HAS_PCI
251
	select I8253
L
Linus Torvalds 已提交
252
	select I8259
253 254
	select MIPS_BOARDS_GEN
	select MIPS_BONITO64
255
	select MIPS_CPU_SCACHE
256
	select PCI_GT64XXX_PCI0
257
	select MIPS_MSC
L
Linus Torvalds 已提交
258
	select SWAP_IO_SPACE
259 260 261 262 263
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_HAS_CPU_MIPS64_R1
	select SYS_HAS_CPU_NEVADA
	select SYS_HAS_CPU_RM7000
264
	select SYS_HAS_EARLY_PRINTK
265 266
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
267 268
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN
T
Tim Anderson 已提交
269
	select SYS_SUPPORTS_MIPS_CMP
270
	select SYS_SUPPORTS_MULTITHREADING
271
	select SYS_SUPPORTS_SMARTMIPS
272
	select SYS_SUPPORTS_ZBOOT
L
Linus Torvalds 已提交
273
	help
274
	  This enables support for the MIPS Technologies Malta evaluation
L
Linus Torvalds 已提交
275 276
	  board.

277
config MIPS_SIM
278
	bool 'MIPS simulator (MIPSsim)'
279
	select CEVT_R4K
280
	select CSRC_R4K
L
Linus Torvalds 已提交
281
	select DMA_NONCOHERENT
282
	select SYS_HAS_EARLY_PRINTK
L
Linus Torvalds 已提交
283
	select IRQ_CPU
M
Marc St-Jean 已提交
284
	select BOOT_RAW
285 286
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_CPU_MIPS32_R2
287
	select SYS_HAS_EARLY_PRINTK
288
	select SYS_SUPPORTS_32BIT_KERNEL
289
	select SYS_SUPPORTS_BIG_ENDIAN
290
	select SYS_SUPPORTS_MULTITHREADING
291
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
292
	help
293 294
	  This option enables support for MIPS Technologies MIPSsim software
	  emulator.
L
Linus Torvalds 已提交
295

296 297 298 299 300 301
config NEC_MARKEINS
	bool "NEC EMMA2RH Mark-eins board"
	select SOC_EMMA2RH
	select HW_HAS_PCI
	help
	  This enables support for the NEC Electronics Mark-eins boards.
302

303
config MACH_VR41XX
304
	bool "NEC VR4100 series based machines"
305
	select CEVT_R4K
306
	select CSRC_R4K
307
	select SYS_HAS_CPU_VR41XX
308
	select ARCH_REQUIRE_GPIOLIB
309

310 311 312 313 314 315 316 317 318 319 320 321 322
config NXP_STB220
	bool "NXP STB220 board"
	select SOC_PNX833X
	help
	 Support for NXP Semiconductors STB220 Development Board.

config NXP_STB225
	bool "NXP 225 board"
	select SOC_PNX833X
	select SOC_PNX8335
	help
	 Support for NXP Semiconductors STB225 Development Board.

323
config PNX8550_JBS
324
	bool "NXP PNX8550 based JBS board"
325 326 327 328
	select PNX8550
	select SYS_SUPPORTS_LITTLE_ENDIAN

config PNX8550_STB810
329
	bool "NXP PNX8550 based STB810 board"
330 331 332
	select PNX8550
	select SYS_SUPPORTS_LITTLE_ENDIAN

M
Marc St-Jean 已提交
333 334 335
config PMC_MSP
	bool "PMC-Sierra MSP chipsets"
	depends on EXPERIMENTAL
336 337
	select CEVT_R4K
	select CSRC_R4K
M
Marc St-Jean 已提交
338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354
	select DMA_NONCOHERENT
	select SWAP_IO_SPACE
	select NO_EXCEPT_FILL
	select BOOT_RAW
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select IRQ_CPU
	select SERIAL_8250
	select SERIAL_8250_CONSOLE
	help
	  This adds support for the PMC-Sierra family of Multi-Service
	  Processor System-On-A-Chips.  These parts include a number
	  of integrated peripherals, interfaces and DSPs in addition to
	  a variety of MIPS cores.

355
config PMC_YOSEMITE
356
	bool "PMC-Sierra Yosemite eval board"
357
	select CEVT_R4K
358
	select CSRC_R4K
359 360 361 362 363 364
	select DMA_COHERENT
	select HW_HAS_PCI
	select IRQ_CPU
	select IRQ_CPU_RM7K
	select IRQ_CPU_RM9K
	select SWAP_IO_SPACE
365
	select SYS_HAS_CPU_RM9000
366
	select SYS_HAS_EARLY_PRINTK
367 368 369 370
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
371
	select SYS_SUPPORTS_SMP
372 373 374
	help
	  Yosemite is an evaluation board for the RM9000x2 processor
	  manufactured by PMC-Sierra.
L
Linus Torvalds 已提交
375

376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393
config POWERTV
	bool "Cisco PowerTV"
	select BOOT_ELF32
	select CEVT_R4K
	select CPU_MIPSR2_IRQ_VI
	select CPU_MIPSR2_IRQ_EI
	select CSRC_POWERTV
	select DMA_NONCOHERENT
	select HW_HAS_PCI
	select SYS_HAS_EARLY_PRINTK
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
	select USB_OHCI_LITTLE_ENDIAN
	help
	  This enables support for the Cisco PowerTV Platform.

L
Linus Torvalds 已提交
394
config SGI_IP22
395
	bool "SGI IP22 (Indy/Indigo2)"
L
Linus Torvalds 已提交
396 397 398
	select ARC
	select ARC32
	select BOOT_ELF32
399
	select CEVT_R4K
400
	select CSRC_R4K
T
Thomas Bogendoerfer 已提交
401
	select DEFAULT_SGI_PARTITION
L
Linus Torvalds 已提交
402
	select DMA_NONCOHERENT
403
	select HW_HAS_EISA
404
	select I8253
405
	select I8259
L
Linus Torvalds 已提交
406 407
	select IP22_CPU_SCACHE
	select IRQ_CPU
408
	select GENERIC_ISA_DMA_SUPPORT_BROKEN
T
Thomas Bogendoerfer 已提交
409 410
	select SGI_HAS_I8042
	select SGI_HAS_INDYDOG
411
	select SGI_HAS_HAL2
T
Thomas Bogendoerfer 已提交
412 413 414
	select SGI_HAS_SEEQ
	select SGI_HAS_WD93
	select SGI_HAS_ZILOG
L
Linus Torvalds 已提交
415
	select SWAP_IO_SPACE
416 417
	select SYS_HAS_CPU_R4X00
	select SYS_HAS_CPU_R5000
418 419 420 421 422 423 424 425
	#
	# Disable EARLY_PRINTK for now since it leads to overwritten prom
	# memory during early boot on some machines.
	#
	# See http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=20091119164009.GA15038%40deprecation.cyrius.com
	# for a more details discussion
	#
	# select SYS_HAS_EARLY_PRINTK
426 427
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
428
	select SYS_SUPPORTS_BIG_ENDIAN
L
Linus Torvalds 已提交
429 430 431 432 433 434
	help
	  This are the SGI Indy, Challenge S and Indigo2, as well as certain
	  OEM variants like the Tandem CMN B006S. To compile a Linux kernel
	  that runs on these, say Y here.

config SGI_IP27
435
	bool "SGI IP27 (Origin200/2000)"
L
Linus Torvalds 已提交
436 437
	select ARC
	select ARC64
438
	select BOOT_ELF64
T
Thomas Bogendoerfer 已提交
439
	select DEFAULT_SGI_PARTITION
440
	select DMA_COHERENT
441
	select SYS_HAS_EARLY_PRINTK
L
Linus Torvalds 已提交
442
	select HW_HAS_PCI
443
	select NR_CPUS_DEFAULT_64
444
	select SYS_HAS_CPU_R10000
445
	select SYS_SUPPORTS_64BIT_KERNEL
446
	select SYS_SUPPORTS_BIG_ENDIAN
447
	select SYS_SUPPORTS_NUMA
448
	select SYS_SUPPORTS_SMP
L
Linus Torvalds 已提交
449 450 451 452 453
	help
	  This are the SGI Origin 200, Origin 2000 and Onyx 2 Graphics
	  workstations.  To compile a Linux kernel that runs on these, say Y
	  here.

T
Thomas Bogendoerfer 已提交
454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470
config SGI_IP28
	bool "SGI IP28 (Indigo2 R10k) (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	select ARC
	select ARC64
	select BOOT_ELF64
	select CEVT_R4K
	select CSRC_R4K
	select DEFAULT_SGI_PARTITION
	select DMA_NONCOHERENT
	select GENERIC_ISA_DMA_SUPPORT_BROKEN
	select IRQ_CPU
	select HW_HAS_EISA
	select I8253
	select I8259
	select SGI_HAS_I8042
	select SGI_HAS_INDYDOG
471
	select SGI_HAS_HAL2
T
Thomas Bogendoerfer 已提交
472 473 474 475 476
	select SGI_HAS_SEEQ
	select SGI_HAS_WD93
	select SGI_HAS_ZILOG
	select SWAP_IO_SPACE
	select SYS_HAS_CPU_R10000
477 478 479 480 481 482 483 484
	#
	# Disable EARLY_PRINTK for now since it leads to overwritten prom
	# memory during early boot on some machines.
	#
	# See http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=20091119164009.GA15038%40deprecation.cyrius.com
	# for a more details discussion
	#
	# select SYS_HAS_EARLY_PRINTK
T
Thomas Bogendoerfer 已提交
485 486 487 488 489 490
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
      help
        This is the SGI Indigo2 with R10000 processor.  To compile a Linux
        kernel that runs on these, say Y here.

L
Linus Torvalds 已提交
491
config SGI_IP32
492
	bool "SGI IP32 (O2)"
L
Linus Torvalds 已提交
493 494 495
	select ARC
	select ARC32
	select BOOT_ELF32
496
	select CEVT_R4K
497
	select CSRC_R4K
L
Linus Torvalds 已提交
498 499
	select DMA_NONCOHERENT
	select HW_HAS_PCI
500
	select IRQ_CPU
L
Linus Torvalds 已提交
501 502
	select R5000_CPU_SCACHE
	select RM7000_CPU_SCACHE
503 504 505
	select SYS_HAS_CPU_R5000
	select SYS_HAS_CPU_R10000 if BROKEN
	select SYS_HAS_CPU_RM7000
R
Ralf Baechle 已提交
506
	select SYS_HAS_CPU_NEVADA
507
	select SYS_SUPPORTS_64BIT_KERNEL
508 509
	select SYS_SUPPORTS_BIG_ENDIAN
	help
510
	  If you want this kernel to run on SGI O2 workstation, say Y here.
L
Linus Torvalds 已提交
511

512 513 514
config SIBYTE_CRHINE
	bool "Sibyte BCM91120C-CRhine"
	depends on EXPERIMENTAL
A
Andrew Isaacson 已提交
515 516
	select BOOT_ELF32
	select DMA_COHERENT
517
	select SIBYTE_BCM1120
A
Andrew Isaacson 已提交
518
	select SWAP_IO_SPACE
519
	select SYS_HAS_CPU_SB1
A
Andrew Isaacson 已提交
520 521 522
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN

523 524 525
config SIBYTE_CARMEL
	bool "Sibyte BCM91120x-Carmel"
	depends on EXPERIMENTAL
526
	select BOOT_ELF32
L
Linus Torvalds 已提交
527
	select DMA_COHERENT
528
	select SIBYTE_BCM1120
529
	select SWAP_IO_SPACE
530
	select SYS_HAS_CPU_SB1
531
	select SYS_SUPPORTS_BIG_ENDIAN
532
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
533

534 535
config SIBYTE_CRHONE
	bool "Sibyte BCM91125C-CRhone"
536 537 538
	depends on EXPERIMENTAL
	select BOOT_ELF32
	select DMA_COHERENT
539
	select SIBYTE_BCM1125
540
	select SWAP_IO_SPACE
541
	select SYS_HAS_CPU_SB1
542
	select SYS_SUPPORTS_BIG_ENDIAN
543
	select SYS_SUPPORTS_HIGHMEM
544
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
545

546
config SIBYTE_RHONE
547
	bool "Sibyte BCM91125E-Rhone"
548 549 550 551 552
	depends on EXPERIMENTAL
	select BOOT_ELF32
	select DMA_COHERENT
	select SIBYTE_BCM1125H
	select SWAP_IO_SPACE
553
	select SYS_HAS_CPU_SB1
554 555
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
556

557 558
config SIBYTE_SWARM
	bool "Sibyte BCM91250A-SWARM"
559
	select BOOT_ELF32
P
Pete Popov 已提交
560
	select DMA_COHERENT
561
	select HAVE_PATA_PLATFORM
562 563
	select NR_CPUS_DEFAULT_2
	select SIBYTE_SB1250
564
	select SWAP_IO_SPACE
565
	select SYS_HAS_CPU_SB1
566
	select SYS_SUPPORTS_BIG_ENDIAN
567
	select SYS_SUPPORTS_HIGHMEM
P
Pete Popov 已提交
568
	select SYS_SUPPORTS_LITTLE_ENDIAN
569
	select ZONE_DMA32 if 64BIT
P
Pete Popov 已提交
570

571 572
config SIBYTE_LITTLESUR
	bool "Sibyte BCM91250C2-LittleSur"
573 574 575
	depends on EXPERIMENTAL
	select BOOT_ELF32
	select DMA_COHERENT
576
	select HAVE_PATA_PLATFORM
577
	select NR_CPUS_DEFAULT_2
578 579
	select SIBYTE_SB1250
	select SWAP_IO_SPACE
580
	select SYS_HAS_CPU_SB1
581 582 583
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
584

585 586
config SIBYTE_SENTOSA
	bool "Sibyte BCM91250E-Sentosa"
587 588 589
	depends on EXPERIMENTAL
	select BOOT_ELF32
	select DMA_COHERENT
590
	select NR_CPUS_DEFAULT_2
591 592
	select SIBYTE_SB1250
	select SWAP_IO_SPACE
593
	select SYS_HAS_CPU_SB1
594 595
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
596

597 598
config SIBYTE_BIGSUR
	bool "Sibyte BCM91480B-BigSur"
599 600
	select BOOT_ELF32
	select DMA_COHERENT
601 602
	select NR_CPUS_DEFAULT_4
	select SIBYTE_BCM1x80
603
	select SWAP_IO_SPACE
604
	select SYS_HAS_CPU_SB1
605
	select SYS_SUPPORTS_BIG_ENDIAN
R
Ralf Baechle 已提交
606
	select SYS_SUPPORTS_HIGHMEM
607
	select SYS_SUPPORTS_LITTLE_ENDIAN
608
	select ZONE_DMA32 if 64BIT
L
Linus Torvalds 已提交
609

610 611
config SNI_RM
	bool "SNI RM200/300/400"
612 613
	select ARC if CPU_LITTLE_ENDIAN
	select ARC32 if CPU_LITTLE_ENDIAN
614
	select SNIPROM if CPU_BIG_ENDIAN
615
	select ARCH_MAY_HAVE_PC_FDC
L
Linus Torvalds 已提交
616
	select BOOT_ELF32
617
	select CEVT_R4K
618
	select CSRC_R4K
T
Thomas Bogendoerfer 已提交
619
	select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
L
Linus Torvalds 已提交
620 621
	select DMA_NONCOHERENT
	select GENERIC_ISA_DMA
622
	select HW_HAS_EISA
L
Linus Torvalds 已提交
623
	select HW_HAS_PCI
624
	select IRQ_CPU
625
	select I8253
L
Linus Torvalds 已提交
626 627
	select I8259
	select ISA
628
	select SWAP_IO_SPACE if CPU_BIG_ENDIAN
629
	select SYS_HAS_CPU_R4X00
630
	select SYS_HAS_CPU_R5000
631
	select SYS_HAS_CPU_R10000
632
	select R5000_CPU_SCACHE
633
	select SYS_HAS_EARLY_PRINTK
634 635
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
636
	select SYS_SUPPORTS_BIG_ENDIAN
R
Ralf Baechle 已提交
637
	select SYS_SUPPORTS_HIGHMEM
638
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
639
	help
640 641
	  The SNI RM200/300/400 are MIPS-based machines manufactured by
	  Siemens Nixdorf Informationssysteme (SNI), parent company of Pyramid
L
Linus Torvalds 已提交
642 643 644
	  Technology and now in turn merged with Fujitsu.  Say Y here to
	  support this machine type.

645 646
config MACH_TX39XX
	bool "Toshiba TX39 series based machines"
647

648 649
config MACH_TX49XX
	bool "Toshiba TX49 series based machines"
650

651 652 653 654 655 656 657 658 659 660 661 662
config MIKROTIK_RB532
	bool "Mikrotik RB532 boards"
	select CEVT_R4K
	select CSRC_R4K
	select DMA_NONCOHERENT
	select HW_HAS_PCI
	select IRQ_CPU
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
	select SWAP_IO_SPACE
	select BOOT_RAW
663
	select ARCH_REQUIRE_GPIOLIB
664 665 666 667
	help
	  Support the Mikrotik(tm) RouterBoard 532 series,
	  based on the IDT RC32434 SoC.

668 669
config WR_PPMC
	bool "Wind River PPMC board"
670
	select CEVT_R4K
671
	select CSRC_R4K
672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690
	select IRQ_CPU
	select BOOT_ELF32
	select DMA_NONCOHERENT
	select HW_HAS_PCI
	select PCI_GT64XXX_PCI0
	select SWAP_IO_SPACE
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_HAS_CPU_MIPS64_R1
	select SYS_HAS_CPU_NEVADA
	select SYS_HAS_CPU_RM7000
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN
	help
	  This enables support for the Wind River MIPS32 4KC PPMC evaluation
	  board, which is based on GT64120 bridge chip.

691
config CAVIUM_OCTEON_SIMULATOR
692
	bool "Cavium Networks Octeon Simulator"
693 694 695 696 697 698
	select CEVT_R4K
	select 64BIT_PHYS_ADDR
	select DMA_COHERENT
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
699
	select SYS_SUPPORTS_HOTPLUG_CPU
700
	select SYS_HAS_CPU_CAVIUM_OCTEON
701 702 703 704 705 706
	help
	  The Octeon simulator is software performance model of the Cavium
	  Octeon Processor. It supports simulating Octeon processors on x86
	  hardware.

config CAVIUM_OCTEON_REFERENCE_BOARD
707
	bool "Cavium Networks Octeon reference board"
708 709 710 711 712 713
	select CEVT_R4K
	select 64BIT_PHYS_ADDR
	select DMA_COHERENT
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
714
	select SYS_SUPPORTS_HOTPLUG_CPU
715
	select SYS_HAS_EARLY_PRINTK
716
	select SYS_HAS_CPU_CAVIUM_OCTEON
717
	select SWAP_IO_SPACE
718 719
	select HW_HAS_PCI
	select ARCH_SUPPORTS_MSI
D
David Daney 已提交
720
	select ZONE_DMA32
721 722
	select USB_ARCH_HAS_OHCI
	select USB_ARCH_HAS_EHCI
723 724 725 726 727 728 729 730 731 732 733 734 735
	help
	  This option supports all of the Octeon reference boards from Cavium
	  Networks. It builds a kernel that dynamically determines the Octeon
	  CPU type and supports all known board reference implementations.
	  Some of the supported boards are:
		EBT3000
		EBH3000
		EBH3100
		Thunder
		Kodama
		Hikari
	  Say Y here for most Octeon reference boards.

736
endchoice
L
Linus Torvalds 已提交
737

R
Ralf Baechle 已提交
738
source "arch/mips/alchemy/Kconfig"
739
source "arch/mips/ath79/Kconfig"
740
source "arch/mips/bcm63xx/Kconfig"
741
source "arch/mips/jazz/Kconfig"
742
source "arch/mips/jz4740/Kconfig"
743
source "arch/mips/lasat/Kconfig"
744
source "arch/mips/pmc-sierra/Kconfig"
745
source "arch/mips/powertv/Kconfig"
746
source "arch/mips/sgi-ip27/Kconfig"
747
source "arch/mips/sibyte/Kconfig"
A
Atsushi Nemoto 已提交
748
source "arch/mips/txx9/Kconfig"
749
source "arch/mips/vr41xx/Kconfig"
750
source "arch/mips/cavium-octeon/Kconfig"
751
source "arch/mips/loongson/Kconfig"
752

753 754
endmenu

L
Linus Torvalds 已提交
755 756 757 758 759 760 761
config RWSEM_GENERIC_SPINLOCK
	bool
	default y

config RWSEM_XCHGADD_ALGORITHM
	bool

762 763 764 765 766 767 768 769
config ARCH_HAS_ILOG2_U32
	bool
	default n

config ARCH_HAS_ILOG2_U64
	bool
	default n

R
Ralf Baechle 已提交
770 771 772 773
config ARCH_SUPPORTS_OPROFILE
	bool
	default y if !MIPS_MT_SMTC

774 775 776 777 778 779 780 781
config GENERIC_FIND_NEXT_BIT
	bool
	default y

config GENERIC_HWEIGHT
	bool
	default y

L
Linus Torvalds 已提交
782 783 784 785
config GENERIC_CALIBRATE_DELAY
	bool
	default y

786 787 788 789
config GENERIC_CLOCKEVENTS
	bool
	default y

790 791 792 793
config GENERIC_CMOS_UPDATE
	bool
	default y

794
config SCHED_OMIT_FRAME_POINTER
795 796 797
	bool
	default y

L
Linus Torvalds 已提交
798 799 800 801 802 803
#
# Select some configuration options automatically based on user selections.
#
config ARC
	bool

804 805 806
config ARCH_MAY_HAVE_PC_FDC
	bool

M
Marc St-Jean 已提交
807 808 809
config BOOT_RAW
	bool

810 811 812
config CEVT_BCM1480
	bool

813 814 815
config CEVT_DS1287
	bool

816 817 818
config CEVT_GT641XX
	bool

819 820 821
config CEVT_R4K_LIB
	bool

822
config CEVT_R4K
823
	select CEVT_R4K_LIB
824 825
	bool

826 827 828
config CEVT_SB1250
	bool

829 830 831
config CEVT_TXX9
	bool

832 833 834
config CSRC_BCM1480
	bool

835 836 837
config CSRC_IOASIC
	bool

838 839 840
config CSRC_POWERTV
	bool

841 842 843
config CSRC_R4K_LIB
	bool

844
config CSRC_R4K
845
	select CSRC_R4K_LIB
846 847
	bool

848 849 850
config CSRC_SB1250
	bool

851 852
config GPIO_TXX9
	select GENERIC_GPIO
M
Michael Buesch 已提交
853
	select ARCH_REQUIRE_GPIOLIB
854 855
	bool

856 857 858
config CFE
	bool

859
config DMA_COHERENT
L
Linus Torvalds 已提交
860 861
	bool

862 863
config DMA_NONCOHERENT
	bool
864
	select NEED_DMA_MAP_STATE
865

866
config NEED_DMA_MAP_STATE
L
Linus Torvalds 已提交
867 868
	bool

869
config SYS_HAS_EARLY_PRINTK
L
Linus Torvalds 已提交
870 871
	bool

872
config HOTPLUG_CPU
873 874 875 876 877 878 879 880 881 882
	bool "Support for hot-pluggable CPUs"
	depends on SMP && HOTPLUG && SYS_SUPPORTS_HOTPLUG_CPU
	help
	  Say Y here to allow turning CPUs off and on. CPUs can be
	  controlled through /sys/devices/system/cpu.
	  (Note: power management support will enable this option
	    automatically on SMP systems. )
	  Say N if you want to disable CPU hotplug.

config SYS_SUPPORTS_HOTPLUG_CPU
883 884
	bool

L
Linus Torvalds 已提交
885 886 887 888 889 890 891 892 893
config I8259
	bool

config MIPS_BONITO64
	bool

config MIPS_MSC
	bool

894 895 896
config MIPS_NILE4
	bool

L
Linus Torvalds 已提交
897 898 899
config MIPS_DISABLE_OBSOLETE_IDE
	bool

900 901 902
config SYNC_R4K
	bool

903 904 905
config MIPS_MACHINE
	def_bool n

906 907 908
config NO_IOPORT
	def_bool n

909 910 911
config GENERIC_ISA_DMA
	bool
	select ZONE_DMA if GENERIC_ISA_DMA_SUPPORT_BROKEN=n
912
	select ISA_DMA_API
913

914 915
config GENERIC_ISA_DMA_SUPPORT_BROKEN
	bool
916
	select GENERIC_ISA_DMA
917

918 919 920
config ISA_DMA_API
	bool

Y
Yoichi Yuasa 已提交
921 922 923
config GENERIC_GPIO
	bool

924
#
M
Matt LaPlante 已提交
925
# Endianess selection.  Sufficiently obscure so many users don't know what to
926 927 928 929 930
# answer,so we try hard to limit the available choices.  Also the use of a
# choice statement should be more obvious to the user.
#
choice
	prompt "Endianess selection"
L
Linus Torvalds 已提交
931 932
	help
	  Some MIPS machines can be configured for either little or big endian
933
	  byte order. These modes require different kernels and a different
M
Matt LaPlante 已提交
934
	  Linux distribution.  In general there is one preferred byteorder for a
935
	  particular system but some systems are just as commonly used in the
936
	  one or the other endianness.
937 938 939 940 941 942 943 944 945 946 947 948

config CPU_BIG_ENDIAN
	bool "Big endian"
	depends on SYS_SUPPORTS_BIG_ENDIAN

config CPU_LITTLE_ENDIAN
	bool "Little endian"
	depends on SYS_SUPPORTS_LITTLE_ENDIAN
	help

endchoice

949 950 951
config EXPORT_UASM
	bool

952 953 954
config SYS_SUPPORTS_APM_EMULATION
	bool

955 956 957 958 959
config SYS_SUPPORTS_BIG_ENDIAN
	bool

config SYS_SUPPORTS_LITTLE_ENDIAN
	bool
L
Linus Torvalds 已提交
960

961 962 963 964 965
config SYS_SUPPORTS_HUGETLBFS
	bool
	depends on CPU_SUPPORTS_HUGEPAGES && 64BIT
	default y

L
Linus Torvalds 已提交
966 967 968 969 970 971
config IRQ_CPU
	bool

config IRQ_CPU_RM7K
	bool

972 973 974
config IRQ_CPU_RM9K
	bool

M
Marc St-Jean 已提交
975 976 977 978 979 980
config IRQ_MSP_SLP
	bool

config IRQ_MSP_CIC
	bool

981 982 983
config IRQ_TXX9
	bool

Y
Yoichi Yuasa 已提交
984 985 986
config IRQ_GT641XX
	bool

987 988 989
config IRQ_GIC
	bool

990 991 992
config IRQ_CPU_OCTEON
	bool

L
Linus Torvalds 已提交
993 994 995
config MIPS_BOARDS_GEN
	bool

996
config PCI_GT64XXX_PCI0
L
Linus Torvalds 已提交
997 998
	bool

M
Marc St-Jean 已提交
999 1000 1001
config NO_EXCEPT_FILL
	bool

1002 1003 1004 1005
config MIPS_RM9122
	bool
	select SERIAL_RM9000

1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017
config SOC_EMMA2RH
	bool
	select CEVT_R4K
	select CSRC_R4K
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_HAS_CPU_R5500
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN

1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034
config SOC_PNX833X
	bool
	select CEVT_R4K
	select CSRC_R4K
	select IRQ_CPU
	select DMA_NONCOHERENT
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
	select SYS_SUPPORTS_BIG_ENDIAN
	select GENERIC_GPIO
	select CPU_MIPSR2_IRQ_VI

config SOC_PNX8335
	bool
	select SOC_PNX833X

1035 1036 1037 1038 1039 1040 1041 1042
config PNX8550
	bool
	select SOC_PNX8550

config SOC_PNX8550
	bool
	select DMA_NONCOHERENT
	select HW_HAS_PCI
1043
	select SYS_HAS_CPU_MIPS32_R1
1044
	select SYS_HAS_EARLY_PRINTK
1045
	select SYS_SUPPORTS_32BIT_KERNEL
1046
	select GENERIC_GPIO
1047

L
Linus Torvalds 已提交
1048 1049 1050
config SWAP_IO_SPACE
	bool

1051 1052 1053
config SERIAL_RM9000
	bool

T
Thomas Bogendoerfer 已提交
1054 1055 1056
config SGI_HAS_INDYDOG
	bool

1057 1058 1059
config SGI_HAS_HAL2
	bool

T
Thomas Bogendoerfer 已提交
1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074
config SGI_HAS_SEEQ
	bool

config SGI_HAS_WD93
	bool

config SGI_HAS_ZILOG
	bool

config SGI_HAS_I8042
	bool

config DEFAULT_SGI_PARTITION
	bool

1075 1076 1077
config ARC32
	bool

1078 1079 1080
config SNIPROM
	bool

L
Linus Torvalds 已提交
1081 1082 1083 1084 1085
config BOOT_ELF32
	bool

config MIPS_L1_CACHE_SHIFT
	int
1086
	default "4" if MACH_DECSTATION || MIKROTIK_RB532 || PMC_MSP4200_EVAL
1087
	default "6" if MIPS_CPU_SCACHE
1088
	default "7" if SGI_IP22 || SGI_IP27 || SGI_IP28 || SNI_RM || CPU_CAVIUM_OCTEON
L
Linus Torvalds 已提交
1089 1090 1091 1092 1093 1094 1095
	default "5"

config HAVE_STD_PC_SERIAL_PORT
	bool

config ARC_CONSOLE
	bool "ARC console support"
T
Thomas Bogendoerfer 已提交
1096
	depends on SGI_IP22 || SGI_IP28 || (SNI_RM && CPU_LITTLE_ENDIAN)
L
Linus Torvalds 已提交
1097 1098 1099

config ARC_MEMORY
	bool
1100
	depends on MACH_JAZZ || SNI_RM || SGI_IP32
L
Linus Torvalds 已提交
1101 1102 1103 1104
	default y

config ARC_PROMLIB
	bool
T
Thomas Bogendoerfer 已提交
1105
	depends on MACH_JAZZ || SNI_RM || SGI_IP22 || SGI_IP28 || SGI_IP32
L
Linus Torvalds 已提交
1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119
	default y

config ARC64
	bool

config BOOT_ELF64
	bool

menu "CPU selection"

choice
	prompt "CPU type"
	default CPU_R4X00

1120 1121 1122 1123
config CPU_LOONGSON2E
	bool "Loongson 2E"
	depends on SYS_HAS_CPU_LOONGSON2E
	select CPU_LOONGSON2
1124 1125 1126 1127
	help
	  The Loongson 2E processor implements the MIPS III instruction set
	  with many extensions.

1128 1129 1130 1131 1132 1133 1134
	  It has an internal FPGA northbridge, which is compatiable to
	  bonito64.

config CPU_LOONGSON2F
	bool "Loongson 2F"
	depends on SYS_HAS_CPU_LOONGSON2F
	select CPU_LOONGSON2
1135 1136
	select GENERIC_GPIO
	select ARCH_REQUIRE_GPIOLIB
1137 1138 1139 1140 1141 1142 1143 1144
	help
	  The Loongson 2F processor implements the MIPS III instruction set
	  with many extensions.

	  Loongson2F have built-in DDR2 and PCIX controller. The PCIX controller
	  have a similar programming interface with FPGA northbridge used in
	  Loongson2E.

1145 1146
config CPU_MIPS32_R1
	bool "MIPS32 Release 1"
1147
	depends on SYS_HAS_CPU_MIPS32_R1
1148
	select CPU_HAS_PREFETCH
R
Ralf Baechle 已提交
1149
	select CPU_SUPPORTS_32BIT_KERNEL
1150
	select CPU_SUPPORTS_HIGHMEM
R
Ralf Baechle 已提交
1151
	help
1152
	  Choose this option to build a kernel for release 1 or later of the
R
Ralf Baechle 已提交
1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163
	  MIPS32 architecture.  Most modern embedded systems with a 32-bit
	  MIPS processor are based on a MIPS32 processor.  If you know the
	  specific type of processor in your system, choose those that one
	  otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.
	  Release 2 of the MIPS32 architecture is available since several
	  years so chances are you even have a MIPS32 Release 2 processor
	  in which case you should choose CPU_MIPS32_R2 instead for better
	  performance.

config CPU_MIPS32_R2
	bool "MIPS32 Release 2"
1164
	depends on SYS_HAS_CPU_MIPS32_R2
R
Ralf Baechle 已提交
1165
	select CPU_HAS_PREFETCH
R
Ralf Baechle 已提交
1166
	select CPU_SUPPORTS_32BIT_KERNEL
1167
	select CPU_SUPPORTS_HIGHMEM
1168
	help
1169
	  Choose this option to build a kernel for release 2 or later of the
1170 1171 1172 1173 1174 1175 1176
	  MIPS32 architecture.  Most modern embedded systems with a 32-bit
	  MIPS processor are based on a MIPS32 processor.  If you know the
	  specific type of processor in your system, choose those that one
	  otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.

config CPU_MIPS64_R1
	bool "MIPS64 Release 1"
1177
	depends on SYS_HAS_CPU_MIPS64_R1
R
Ralf Baechle 已提交
1178
	select CPU_HAS_PREFETCH
1179 1180
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
1181
	select CPU_SUPPORTS_HIGHMEM
1182
	select CPU_SUPPORTS_HUGEPAGES
1183 1184 1185 1186 1187 1188
	help
	  Choose this option to build a kernel for release 1 or later of the
	  MIPS64 architecture.  Many modern embedded systems with a 64-bit
	  MIPS processor are based on a MIPS64 processor.  If you know the
	  specific type of processor in your system, choose those that one
	  otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
R
Ralf Baechle 已提交
1189 1190 1191 1192 1193 1194 1195
	  Release 2 of the MIPS64 architecture is available since several
	  years so chances are you even have a MIPS64 Release 2 processor
	  in which case you should choose CPU_MIPS64_R2 instead for better
	  performance.

config CPU_MIPS64_R2
	bool "MIPS64 Release 2"
1196
	depends on SYS_HAS_CPU_MIPS64_R2
R
Ralf Baechle 已提交
1197
	select CPU_HAS_PREFETCH
R
Ralf Baechle 已提交
1198 1199
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
1200
	select CPU_SUPPORTS_HIGHMEM
1201
	select CPU_SUPPORTS_HUGEPAGES
R
Ralf Baechle 已提交
1202 1203 1204 1205 1206 1207
	help
	  Choose this option to build a kernel for release 2 or later of the
	  MIPS64 architecture.  Many modern embedded systems with a 64-bit
	  MIPS processor are based on a MIPS64 processor.  If you know the
	  specific type of processor in your system, choose those that one
	  otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
L
Linus Torvalds 已提交
1208 1209 1210

config CPU_R3000
	bool "R3000"
1211
	depends on SYS_HAS_CPU_R3000
1212
	select CPU_HAS_WB
1213
	select CPU_SUPPORTS_32BIT_KERNEL
R
Ralf Baechle 已提交
1214
	select CPU_SUPPORTS_HIGHMEM
L
Linus Torvalds 已提交
1215 1216 1217 1218 1219 1220 1221 1222 1223 1224
	help
	  Please make sure to pick the right CPU type. Linux/MIPS is not
	  designed to be generic, i.e. Kernels compiled for R3000 CPUs will
	  *not* work on R4000 machines and vice versa.  However, since most
	  of the supported machines have an R4000 (or similar) CPU, R4x00
	  might be a safe bet.  If the resulting kernel does not work,
	  try to recompile with R3000.

config CPU_TX39XX
	bool "R39XX"
1225
	depends on SYS_HAS_CPU_TX39XX
1226
	select CPU_SUPPORTS_32BIT_KERNEL
L
Linus Torvalds 已提交
1227 1228 1229

config CPU_VR41XX
	bool "R41xx"
1230
	depends on SYS_HAS_CPU_VR41XX
1231 1232
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1233
	help
1234
	  The options selects support for the NEC VR4100 series of processors.
L
Linus Torvalds 已提交
1235 1236 1237 1238 1239 1240
	  Only choose this option if you have one of these processors as a
	  kernel built with this option will not run on any other type of
	  processor or vice versa.

config CPU_R4300
	bool "R4300"
1241
	depends on SYS_HAS_CPU_R4300
1242 1243
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1244 1245 1246 1247 1248
	help
	  MIPS Technologies R4300-series processors.

config CPU_R4X00
	bool "R4x00"
1249
	depends on SYS_HAS_CPU_R4X00
1250 1251
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1252 1253 1254 1255 1256 1257
	help
	  MIPS Technologies R4000-series processors other than 4300, including
	  the R4000, R4400, R4600, and 4700.

config CPU_TX49XX
	bool "R49XX"
1258
	depends on SYS_HAS_CPU_TX49XX
A
Atsushi Nemoto 已提交
1259
	select CPU_HAS_PREFETCH
1260 1261
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1262 1263 1264

config CPU_R5000
	bool "R5000"
1265
	depends on SYS_HAS_CPU_R5000
1266 1267
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1268 1269 1270 1271 1272
	help
	  MIPS Technologies R5000-series processors other than the Nevada.

config CPU_R5432
	bool "R5432"
1273
	depends on SYS_HAS_CPU_R5432
1274 1275
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1276

1277 1278 1279 1280 1281
config CPU_R5500
	bool "R5500"
	depends on SYS_HAS_CPU_R5500
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
1282
	select CPU_SUPPORTS_HUGEPAGES
1283 1284 1285 1286
	help
	  NEC VR5500 and VR5500A series processors implement 64-bit MIPS IV
	  instruction set.

L
Linus Torvalds 已提交
1287 1288
config CPU_R6000
	bool "R6000"
1289
	depends on EXPERIMENTAL
1290
	depends on SYS_HAS_CPU_R6000
1291
	select CPU_SUPPORTS_32BIT_KERNEL
L
Linus Torvalds 已提交
1292 1293
	help
	  MIPS Technologies R6000 and R6000A series processors.  Note these
C
Chris Dearman 已提交
1294
	  processors are extremely rare and the support for them is incomplete.
L
Linus Torvalds 已提交
1295 1296 1297

config CPU_NEVADA
	bool "RM52xx"
1298
	depends on SYS_HAS_CPU_NEVADA
1299 1300
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1301 1302 1303 1304 1305
	help
	  QED / PMC-Sierra RM52xx-series ("Nevada") processors.

config CPU_R8000
	bool "R8000"
1306
	depends on EXPERIMENTAL
1307
	depends on SYS_HAS_CPU_R8000
1308
	select CPU_HAS_PREFETCH
1309
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1310 1311 1312 1313 1314 1315
	help
	  MIPS Technologies R8000 processors.  Note these processors are
	  uncommon and the support for them is incomplete.

config CPU_R10000
	bool "R10000"
1316
	depends on SYS_HAS_CPU_R10000
1317
	select CPU_HAS_PREFETCH
1318 1319
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
R
Ralf Baechle 已提交
1320
	select CPU_SUPPORTS_HIGHMEM
L
Linus Torvalds 已提交
1321 1322 1323 1324 1325
	help
	  MIPS Technologies R10000-series processors.

config CPU_RM7000
	bool "RM7000"
1326
	depends on SYS_HAS_CPU_RM7000
1327
	select CPU_HAS_PREFETCH
1328 1329
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
R
Ralf Baechle 已提交
1330
	select CPU_SUPPORTS_HIGHMEM
L
Linus Torvalds 已提交
1331 1332 1333

config CPU_RM9000
	bool "RM9000"
1334
	depends on SYS_HAS_CPU_RM9000
1335
	select CPU_HAS_PREFETCH
1336 1337
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
R
Ralf Baechle 已提交
1338
	select CPU_SUPPORTS_HIGHMEM
1339
	select WEAK_ORDERING
L
Linus Torvalds 已提交
1340 1341 1342

config CPU_SB1
	bool "SB1"
1343
	depends on SYS_HAS_CPU_SB1
1344 1345
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
R
Ralf Baechle 已提交
1346
	select CPU_SUPPORTS_HIGHMEM
1347
	select WEAK_ORDERING
L
Linus Torvalds 已提交
1348

1349 1350
config CPU_CAVIUM_OCTEON
	bool "Cavium Octeon processor"
1351
	depends on SYS_HAS_CPU_CAVIUM_OCTEON
1352 1353 1354 1355 1356 1357 1358 1359
	select IRQ_CPU
	select IRQ_CPU_OCTEON
	select CPU_HAS_PREFETCH
	select CPU_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_SMP
	select NR_CPUS_DEFAULT_16
	select WEAK_ORDERING
	select CPU_SUPPORTS_HIGHMEM
1360
	select CPU_SUPPORTS_HUGEPAGES
1361 1362 1363 1364 1365 1366
	help
	  The Cavium Octeon processor is a highly integrated chip containing
	  many ethernet hardware widgets for networking tasks. The processor
	  can have up to 16 Mips64v2 cores and 8 integrated gigabit ethernets.
	  Full details can be found at http://www.caviumnetworks.com.

1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417
config CPU_BMIPS3300
	bool "BMIPS3300"
	depends on SYS_HAS_CPU_BMIPS3300
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_SUPPORTS_32BIT_KERNEL
	select WEAK_ORDERING
	help
	  Broadcom BMIPS3300 processors.

config CPU_BMIPS4350
	bool "BMIPS4350"
	depends on SYS_HAS_CPU_BMIPS4350
	select CPU_SUPPORTS_32BIT_KERNEL
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_SUPPORTS_SMP
	select SYS_SUPPORTS_HOTPLUG_CPU
	select WEAK_ORDERING
	help
	  Broadcom BMIPS4350 ("VIPER") processors.

config CPU_BMIPS4380
	bool "BMIPS4380"
	depends on SYS_HAS_CPU_BMIPS4380
	select CPU_SUPPORTS_32BIT_KERNEL
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_SUPPORTS_SMP
	select SYS_SUPPORTS_HOTPLUG_CPU
	select WEAK_ORDERING
	help
	  Broadcom BMIPS4380 processors.

config CPU_BMIPS5000
	bool "BMIPS5000"
	depends on SYS_HAS_CPU_BMIPS5000
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_HIGHMEM
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_SUPPORTS_SMP
	select SYS_SUPPORTS_HOTPLUG_CPU
	select WEAK_ORDERING
	help
	  Broadcom BMIPS5000 processors.

L
Linus Torvalds 已提交
1418 1419
endchoice

1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446
if CPU_LOONGSON2F
config CPU_NOP_WORKAROUNDS
	bool

config CPU_JUMP_WORKAROUNDS
	bool

config CPU_LOONGSON2F_WORKAROUNDS
	bool "Loongson 2F Workarounds"
	default y
	select CPU_NOP_WORKAROUNDS
	select CPU_JUMP_WORKAROUNDS
	help
	  Loongson 2F01 / 2F02 processors have the NOP & JUMP issues which
	  require workarounds.  Without workarounds the system may hang
	  unexpectedly.  For more information please refer to the gas
	  -mfix-loongson2f-nop and -mfix-loongson2f-jump options.

	  Loongson 2F03 and later have fixed these issues and no workarounds
	  are needed.  The workarounds have no significant side effect on them
	  but may decrease the performance of the system so this option should
	  be disabled unless the kernel is intended to be run on 2F01 or 2F02
	  systems.

	  If unsure, please say Y.
endif # CPU_LOONGSON2F

1447 1448 1449 1450 1451
config SYS_SUPPORTS_ZBOOT
	bool
	select HAVE_KERNEL_GZIP
	select HAVE_KERNEL_BZIP2
	select HAVE_KERNEL_LZMA
1452
	select HAVE_KERNEL_LZO
1453 1454 1455 1456 1457

config SYS_SUPPORTS_ZBOOT_UART16550
	bool
	select SYS_SUPPORTS_ZBOOT

1458 1459 1460 1461 1462 1463 1464
config CPU_LOONGSON2
	bool
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
	select CPU_SUPPORTS_HIGHMEM

config SYS_HAS_CPU_LOONGSON2E
1465 1466
	bool

1467 1468
config SYS_HAS_CPU_LOONGSON2F
	bool
1469 1470
	select CPU_SUPPORTS_CPUFREQ
	select CPU_SUPPORTS_ADDRWINCFG if 64BIT
1471
	select CPU_SUPPORTS_UNCACHED_ACCELERATED
1472

1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508
config SYS_HAS_CPU_MIPS32_R1
	bool

config SYS_HAS_CPU_MIPS32_R2
	bool

config SYS_HAS_CPU_MIPS64_R1
	bool

config SYS_HAS_CPU_MIPS64_R2
	bool

config SYS_HAS_CPU_R3000
	bool

config SYS_HAS_CPU_TX39XX
	bool

config SYS_HAS_CPU_VR41XX
	bool

config SYS_HAS_CPU_R4300
	bool

config SYS_HAS_CPU_R4X00
	bool

config SYS_HAS_CPU_TX49XX
	bool

config SYS_HAS_CPU_R5000
	bool

config SYS_HAS_CPU_R5432
	bool

1509 1510 1511
config SYS_HAS_CPU_R5500
	bool

1512 1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532
config SYS_HAS_CPU_R6000
	bool

config SYS_HAS_CPU_NEVADA
	bool

config SYS_HAS_CPU_R8000
	bool

config SYS_HAS_CPU_R10000
	bool

config SYS_HAS_CPU_RM7000
	bool

config SYS_HAS_CPU_RM9000
	bool

config SYS_HAS_CPU_SB1
	bool

1533 1534 1535
config SYS_HAS_CPU_CAVIUM_OCTEON
	bool

1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547
config SYS_HAS_CPU_BMIPS3300
	bool

config SYS_HAS_CPU_BMIPS4350
	bool

config SYS_HAS_CPU_BMIPS4380
	bool

config SYS_HAS_CPU_BMIPS5000
	bool

1548 1549 1550 1551
#
# CPU may reorder R->R, R->W, W->R, W->W
# Reordering beyond LL and SC is handled in WEAK_REORDERING_BEYOND_LLSC
#
1552 1553
config WEAK_ORDERING
	bool
1554 1555 1556 1557 1558 1559 1560

#
# CPU may reorder reads and writes beyond LL/SC
# CPU may reorder R->LL, R->LL, W->LL, W->LL, R->SC, R->SC, W->SC, W->SC
#
config WEAK_REORDERING_BEYOND_LLSC
	bool
1561 1562 1563
endmenu

#
C
Chris Dearman 已提交
1564
# These two indicate any level of the MIPS32 and MIPS64 architecture
1565 1566 1567 1568 1569 1570 1571 1572 1573 1574
#
config CPU_MIPS32
	bool
	default y if CPU_MIPS32_R1 || CPU_MIPS32_R2

config CPU_MIPS64
	bool
	default y if CPU_MIPS64_R1 || CPU_MIPS64_R2

#
C
Chris Dearman 已提交
1575
# These two indicate the revision of the architecture, either Release 1 or Release 2
1576 1577 1578 1579 1580 1581 1582
#
config CPU_MIPSR1
	bool
	default y if CPU_MIPS32_R1 || CPU_MIPS64_R1

config CPU_MIPSR2
	bool
1583
	default y if CPU_MIPS32_R2 || CPU_MIPS64_R2 || CPU_CAVIUM_OCTEON
1584 1585 1586 1587 1588 1589 1590 1591 1592

config SYS_SUPPORTS_32BIT_KERNEL
	bool
config SYS_SUPPORTS_64BIT_KERNEL
	bool
config CPU_SUPPORTS_32BIT_KERNEL
	bool
config CPU_SUPPORTS_64BIT_KERNEL
	bool
1593 1594 1595 1596
config CPU_SUPPORTS_CPUFREQ
	bool
config CPU_SUPPORTS_ADDRWINCFG
	bool
1597 1598
config CPU_SUPPORTS_HUGEPAGES
	bool
1599 1600
config CPU_SUPPORTS_UNCACHED_ACCELERATED
	bool
1601 1602 1603
config MIPS_PGD_C0_CONTEXT
	bool
	default y if 64BIT && CPU_MIPSR2
1604

1605 1606 1607 1608 1609
#
# Set to y for ptrace access to watch registers.
#
config HARDWARE_WATCHPOINTS
       bool
1610
       default y if CPU_MIPSR1 || CPU_MIPSR2
1611

1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631
menu "Kernel type"

choice

	prompt "Kernel code model"
	help
	  You should only select this option if you have a workload that
	  actually benefits from 64-bit processing or if your machine has
	  large memory.  You will only be presented a single option in this
	  menu if your system does not support both 32-bit and 64-bit kernels.

config 32BIT
	bool "32-bit kernel"
	depends on CPU_SUPPORTS_32BIT_KERNEL && SYS_SUPPORTS_32BIT_KERNEL
	select TRAD_SIGNALS
	help
	  Select this option if you want to build a 32-bit kernel.
config 64BIT
	bool "64-bit kernel"
	depends on CPU_SUPPORTS_64BIT_KERNEL && SYS_SUPPORTS_64BIT_KERNEL
1632
	select HAVE_SYSCALL_WRAPPERS
1633 1634 1635 1636 1637
	help
	  Select this option if you want to build a 64-bit kernel.

endchoice

L
Linus Torvalds 已提交
1638 1639 1640 1641 1642 1643
choice
	prompt "Kernel page size"
	default PAGE_SIZE_4KB

config PAGE_SIZE_4KB
	bool "4kB"
W
Wu Zhangjin 已提交
1644
	depends on !CPU_LOONGSON2
L
Linus Torvalds 已提交
1645 1646 1647 1648 1649 1650 1651 1652
	help
	 This option select the standard 4kB Linux page size.  On some
	 R3000-family processors this is the only available page size.  Using
	 4kB page size will minimize memory consumption and is therefore
	 recommended for low memory systems.

config PAGE_SIZE_8KB
	bool "8kB"
1653
	depends on (EXPERIMENTAL && CPU_R8000) || CPU_CAVIUM_OCTEON
L
Linus Torvalds 已提交
1654 1655 1656
	help
	  Using 8kB page size will result in higher performance kernel at
	  the price of higher memory consumption.  This option is available
1657 1658
	  only on R8000 and cnMIPS processors.  Note that you will need a
	  suitable Linux distribution to support this.
L
Linus Torvalds 已提交
1659 1660 1661

config PAGE_SIZE_16KB
	bool "16kB"
1662
	depends on !CPU_R3000 && !CPU_TX39XX
L
Linus Torvalds 已提交
1663 1664 1665
	help
	  Using 16kB page size will result in higher performance kernel at
	  the price of higher memory consumption.  This option is available on
1666 1667
	  all non-R3000 family processors.  Note that you will need a suitable
	  Linux distribution to support this.
L
Linus Torvalds 已提交
1668

1669 1670 1671 1672 1673 1674 1675 1676 1677
config PAGE_SIZE_32KB
	bool "32kB"
	depends on CPU_CAVIUM_OCTEON
	help
	  Using 32kB page size will result in higher performance kernel at
	  the price of higher memory consumption.  This option is available
	  only on cnMIPS cores.  Note that you will need a suitable Linux
	  distribution to support this.

L
Linus Torvalds 已提交
1678 1679 1680 1681 1682 1683 1684
config PAGE_SIZE_64KB
	bool "64kB"
	depends on EXPERIMENTAL && !CPU_R3000 && !CPU_TX39XX
	help
	  Using 64kB page size will result in higher performance kernel at
	  the price of higher memory consumption.  This option is available on
	  all non-R3000 family processor.  Not that at the time of this
1685
	  writing this option is still high experimental.
L
Linus Torvalds 已提交
1686 1687 1688

endchoice

1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710
config FORCE_MAX_ZONEORDER
	int "Maximum zone order"
	range 13 64 if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_32KB
	default "13" if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_32KB
	range 12 64 if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_16KB
	default "12" if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_16KB
	range 11 64
	default "11"
	help
	  The kernel memory allocator divides physically contiguous memory
	  blocks into "zones", where each zone is a power of two number of
	  pages.  This option selects the largest power of two that the kernel
	  keeps in the memory allocator.  If you need to allocate very large
	  blocks of physically contiguous memory, then you may need to
	  increase this value.

	  This config option is actually maximum order plus one. For example,
	  a value of 11 means that the largest free memory block is 2^10 pages.

	  The page size is not necessarily 4KB.  Keep this in mind
	  when choosing a value for this option.

L
Linus Torvalds 已提交
1711 1712 1713 1714 1715 1716 1717
config BOARD_SCACHE
	bool

config IP22_CPU_SCACHE
	bool
	select BOARD_SCACHE

1718 1719 1720 1721 1722 1723 1724
#
# Support for a MIPS32 / MIPS64 style S-caches
#
config MIPS_CPU_SCACHE
	bool
	select BOARD_SCACHE

L
Linus Torvalds 已提交
1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741
config R5000_CPU_SCACHE
	bool
	select BOARD_SCACHE

config RM7000_CPU_SCACHE
	bool
	select BOARD_SCACHE

config SIBYTE_DMA_PAGEOPS
	bool "Use DMA to clear/copy pages"
	depends on CPU_SB1
	help
	  Instead of using the CPU to zero and copy pages, use a Data Mover
	  channel.  These DMA channels are otherwise unused by the standard
	  SiByte Linux port.  Seems to give a small performance benefit.

config CPU_HAS_PREFETCH
1742
	bool
L
Linus Torvalds 已提交
1743

R
Ralf Baechle 已提交
1744 1745
choice
	prompt "MIPS MT options"
1746 1747 1748 1749 1750 1751 1752 1753

config MIPS_MT_DISABLED
	bool "Disable multithreading support."
	help
	  Use this option if your workload can't take advantage of
	  MIPS hardware multithreading support.  On systems that don't have
	  the option of an MT-enabled processor this option will be the only
	  option in this menu.
R
Ralf Baechle 已提交
1754

R
Ralf Baechle 已提交
1755 1756
config MIPS_MT_SMP
	bool "Use 1 TC on each available VPE for SMP"
1757
	depends on SYS_SUPPORTS_MULTITHREADING
1758
	select CPU_MIPSR2_IRQ_VI
1759
	select CPU_MIPSR2_IRQ_EI
1760
	select MIPS_MT
1761
	select NR_CPUS_DEFAULT_2
1762
	select SMP
1763
	select SYS_SUPPORTS_SCHED_SMT if SMP
1764
	select SYS_SUPPORTS_SMP
1765
	select SMP_UP
1766
	help
1767 1768 1769 1770 1771 1772 1773 1774 1775 1776
	  This is a kernel model which is known a VSMP but lately has been
	  marketesed into SMVP.
	  Virtual SMP uses the processor's VPEs  to implement virtual
	  processors. In currently available configuration of the 34K processor
	  this allows for a dual processor. Both processors will share the same
	  primary caches; each will obtain the half of the TLB for it's own
	  exclusive use. For a layman this model can be described as similar to
	  what Intel calls Hyperthreading.

	  For further information see http://www.linux-mips.org/wiki/34K#VSMP
1777

R
Ralf Baechle 已提交
1778 1779 1780 1781
config MIPS_MT_SMTC
	bool "SMTC: Use all TCs on all VPEs for SMP"
	depends on CPU_MIPS32_R2
	#depends on CPU_MIPS64_R2		# once there is hardware ...
1782 1783
	depends on SYS_SUPPORTS_MULTITHREADING
	select CPU_MIPSR2_IRQ_VI
1784
	select CPU_MIPSR2_IRQ_EI
1785
	select MIPS_MT
1786
	select NR_CPUS_DEFAULT_8
R
Ralf Baechle 已提交
1787
	select SMP
1788
	select SYS_SUPPORTS_SMP
1789
	select SMP_UP
1790
	help
R
Ralf Baechle 已提交
1791 1792
	  This is a kernel model which is known a SMTC or lately has been
	  marketesed into SMVP.
1793 1794 1795 1796 1797 1798 1799 1800
	  is presenting the available TC's of the core as processors to Linux.
	  On currently available 34K processors this means a Linux system will
	  see up to 5 processors. The implementation of the SMTC kernel differs
	  significantly from VSMP and cannot efficiently coexist in the same
	  kernel binary so the choice between VSMP and SMTC is a compile time
	  decision.

	  For further information see http://www.linux-mips.org/wiki/34K#SMTC
R
Ralf Baechle 已提交
1801 1802 1803

endchoice

1804 1805 1806
config MIPS_MT
	bool

1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819
config SCHED_SMT
	bool "SMT (multithreading) scheduler support"
	depends on SYS_SUPPORTS_SCHED_SMT
	default n
	help
	  SMT scheduler support improves the CPU scheduler's decision making
	  when dealing with MIPS MT enabled cores at a cost of slightly
	  increased overhead in some places. If unsure say N here.

config SYS_SUPPORTS_SCHED_SMT
	bool


1820 1821 1822
config SYS_SUPPORTS_MULTITHREADING
	bool

R
Ralf Baechle 已提交
1823 1824 1825
config MIPS_MT_FPAFF
	bool "Dynamic FPU affinity for FP-intensive threads"
	default y
1826 1827 1828 1829 1830 1831 1832 1833 1834 1835 1836
	depends on MIPS_MT_SMP || MIPS_MT_SMTC

config MIPS_VPE_LOADER
	bool "VPE loader support."
	depends on SYS_SUPPORTS_MULTITHREADING
	select CPU_MIPSR2_IRQ_VI
	select CPU_MIPSR2_IRQ_EI
	select MIPS_MT
	help
	  Includes a loader for loading an elf relocatable object
	  onto another VPE and running it.
R
Ralf Baechle 已提交
1837

1838 1839 1840
config MIPS_MT_SMTC_IM_BACKSTOP
	bool "Use per-TC register bits as backstop for inhibited IM bits"
	depends on MIPS_MT_SMTC
1841
	default n
1842 1843 1844 1845 1846 1847
	help
	  To support multiple TC microthreads acting as "CPUs" within
	  a VPE, VPE-wide interrupt mask bits must be specially manipulated
	  during interrupt handling. To support legacy drivers and interrupt
	  controller management code, SMTC has a "backstop" to track and
	  if necessary restore the interrupt mask. This has some performance
1848
	  impact on interrupt service overhead.
1849

1850 1851 1852 1853 1854 1855 1856 1857
config MIPS_MT_SMTC_IRQAFF
	bool "Support IRQ affinity API"
	depends on MIPS_MT_SMTC
	default n
	help
	  Enables SMP IRQ affinity API (/proc/irq/*/smp_affinity, etc.)
	  for SMTC Linux kernel. Requires platform support, of which
	  an example can be found in the MIPS kernel i8259 and Malta
1858 1859
	  platform code.  Adds some overhead to interrupt dispatch, and
	  should be used only if you know what you are doing.
1860

1861 1862 1863 1864 1865 1866 1867 1868 1869 1870 1871 1872
config MIPS_VPE_LOADER_TOM
	bool "Load VPE program into memory hidden from linux"
	depends on MIPS_VPE_LOADER
	default y
	help
	  The loader can use memory that is present but has been hidden from
	  Linux using the kernel command line option "mem=xxMB". It's up to
	  you to ensure the amount you put in the option and the space your
	  program requires is less or equal to the amount physically present.

# this should possibly be in drivers/char, but it is rather cpu related. Hmmm
config MIPS_VPE_APSP_API
1873 1874 1875
	bool "Enable support for AP/SP API (RTLX)"
	depends on MIPS_VPE_LOADER
	help
1876

1877 1878 1879 1880 1881 1882 1883 1884 1885 1886
config MIPS_APSP_KSPD
	bool "Enable KSPD"
	depends on MIPS_VPE_APSP_API
	default y
	help
	  KSPD is a kernel daemon that accepts syscall requests from the SP
	  side, actions them and returns the results. It also handles the
	  "exit" syscall notifying other kernel modules the SP program is
	  exiting.  You probably want to say yes here.

1887 1888 1889
config MIPS_CMP
	bool "MIPS CMP framework support"
	depends on SYS_SUPPORTS_MIPS_CMP
1890
	select SYNC_R4K
1891 1892 1893 1894 1895 1896 1897 1898
	select SYS_SUPPORTS_SMP
	select SYS_SUPPORTS_SCHED_SMT if SMP
	select WEAK_ORDERING
	default n
	help
	  This is a placeholder option for the GCMP work. It will need to
	  be handled differently...

L
Linus Torvalds 已提交
1899 1900 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914
config SB1_PASS_1_WORKAROUNDS
	bool
	depends on CPU_SB1_PASS_1
	default y

config SB1_PASS_2_WORKAROUNDS
	bool
	depends on CPU_SB1 && (CPU_SB1_PASS_2_2 || CPU_SB1_PASS_2)
	default y

config SB1_PASS_2_1_WORKAROUNDS
	bool
	depends on CPU_SB1 && CPU_SB1_PASS_2
	default y

config 64BIT_PHYS_ADDR
1915
	bool
L
Linus Torvalds 已提交
1916

1917 1918 1919
config ARCH_PHYS_ADDR_T_64BIT
       def_bool 64BIT_PHYS_ADDR

1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931
config CPU_HAS_SMARTMIPS
	depends on SYS_SUPPORTS_SMARTMIPS
	bool "Support for the SmartMIPS ASE"
	help
	  SmartMIPS is a extension of the MIPS32 architecture aimed at
	  increased security at both hardware and software level for
	  smartcards.  Enabling this option will allow proper use of the
	  SmartMIPS instructions by Linux applications.  However a kernel with
	  this option will not work on a MIPS core without SmartMIPS core.  If
	  you don't know you probably don't have SmartMIPS and should say N
	  here.

L
Linus Torvalds 已提交
1932
config CPU_HAS_WB
1933
	bool
1934

1935 1936 1937
#
# Vectored interrupt mode is an R2 feature
#
1938
config CPU_MIPSR2_IRQ_VI
1939
	bool
1940

1941 1942 1943
#
# Extended interrupt mode is an R2 feature
#
1944
config CPU_MIPSR2_IRQ_EI
1945
	bool
1946

L
Linus Torvalds 已提交
1947 1948 1949 1950 1951
config CPU_HAS_SYNC
	bool
	depends on !CPU_R3000
	default y

R
Ralf Baechle 已提交
1952 1953 1954
config GENERIC_CLOCKEVENTS_BROADCAST
	bool

1955 1956 1957 1958 1959 1960 1961 1962 1963 1964 1965 1966 1967
#
# CPU non-features
#
config CPU_DADDI_WORKAROUNDS
	bool

config CPU_R4000_WORKAROUNDS
	bool
	select CPU_R4400_WORKAROUNDS

config CPU_R4400_WORKAROUNDS
	bool

L
Linus Torvalds 已提交
1968 1969 1970 1971 1972 1973 1974 1975 1976
#
# - Highmem only makes sense for the 32-bit kernel.
# - The current highmem code will only work properly on physically indexed
#   caches such as R3000, SB1, R7000 or those that look like they're virtually
#   indexed such as R4000/R4400 SC and MC versions or R10000.  So for the
#   moment we protect the user and offer the highmem option only on machines
#   where it's known to be safe.  This will not offer highmem on a few systems
#   such as MIPS32 and MIPS64 CPUs which may have virtual and physically
#   indexed CPUs but we're playing safe.
R
Ralf Baechle 已提交
1977 1978 1979
# - We use SYS_SUPPORTS_HIGHMEM to offer highmem only for systems where we
#   know they might have memory configurations that could make use of highmem
#   support.
L
Linus Torvalds 已提交
1980 1981 1982
#
config HIGHMEM
	bool "High Memory Support"
R
Ralf Baechle 已提交
1983 1984 1985 1986 1987 1988 1989
	depends on 32BIT && CPU_SUPPORTS_HIGHMEM && SYS_SUPPORTS_HIGHMEM

config CPU_SUPPORTS_HIGHMEM
	bool

config SYS_SUPPORTS_HIGHMEM
	bool
L
Linus Torvalds 已提交
1990

1991 1992 1993
config SYS_SUPPORTS_SMARTMIPS
	bool

1994 1995
config ARCH_FLATMEM_ENABLE
	def_bool y
1996
	depends on !NUMA && !CPU_LOONGSON2
1997

1998 1999 2000 2001
config ARCH_DISCONTIGMEM_ENABLE
	bool
	default y if SGI_IP27
	help
2002
	  Say Y to support efficient handling of discontiguous physical memory,
2003 2004 2005 2006
	  for architectures which are either NUMA (Non-Uniform Memory Access)
	  or have huge holes in the physical address space for other reasons.
	  See <file:Documentation/vm/numa> for more.

2007 2008 2009
config ARCH_POPULATES_NODE_MAP
	def_bool y

2010 2011
config ARCH_SPARSEMEM_ENABLE
	bool
A
Atsushi Nemoto 已提交
2012
	select SPARSEMEM_STATIC
2013

2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026
config NUMA
	bool "NUMA Support"
	depends on SYS_SUPPORTS_NUMA
	help
	  Say Y to compile the kernel to support NUMA (Non-Uniform Memory
	  Access).  This option improves performance on systems with more
	  than two nodes; on two node systems it is generally better to
	  leave it disabled; on single node systems disable this option
	  disabled.

config SYS_SUPPORTS_NUMA
	bool

Y
Yasunori Goto 已提交
2027 2028 2029 2030 2031
config NODES_SHIFT
	int
	default "6"
	depends on NEED_MULTIPLE_NODES

2032 2033 2034 2035 2036 2037 2038 2039
config HW_PERF_EVENTS
	bool "Enable hardware performance counter support for perf events"
	depends on PERF_EVENTS && !MIPS_MT_SMTC && OPROFILE=n && CPU_MIPS32
	default y
	help
	  Enable hardware performance counter support for perf events. If
	  disabled, perf events will use software events only.

2040 2041
source "mm/Kconfig"

L
Linus Torvalds 已提交
2042 2043
config SMP
	bool "Multi-Processing support"
2044
	depends on SYS_SUPPORTS_SMP
2045
	select IRQ_PER_CPU
2046
	select USE_GENERIC_SMP_HELPERS
2047
	help
L
Linus Torvalds 已提交
2048 2049 2050 2051 2052 2053 2054 2055 2056 2057 2058 2059 2060
	  This enables support for systems with more than one CPU. If you have
	  a system with only one CPU, like most personal computers, say N. If
	  you have a system with more than one CPU, say Y.

	  If you say N here, the kernel will run on single and multiprocessor
	  machines, but will use only one CPU of a multiprocessor machine. If
	  you say Y here, the kernel will run on many, but not all,
	  singleprocessor machines. On a singleprocessor machine, the kernel
	  will run faster if you say N here.

	  People using multiprocessor machines who say Y here should also say
	  Y to "Enhanced Real Time Clock Support", below.

A
Adrian Bunk 已提交
2061 2062
	  See also the SMP-HOWTO available at
	  <http://www.tldp.org/docs.html#howto>.
L
Linus Torvalds 已提交
2063 2064 2065

	  If you don't know what to do here, say N.

2066 2067 2068
config SMP_UP
	bool

2069 2070 2071
config SYS_SUPPORTS_MIPS_CMP
	bool

2072 2073 2074
config SYS_SUPPORTS_SMP
	bool

2075 2076 2077
config NR_CPUS_DEFAULT_1
	bool

2078 2079 2080 2081 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091 2092 2093 2094 2095
config NR_CPUS_DEFAULT_2
	bool

config NR_CPUS_DEFAULT_4
	bool

config NR_CPUS_DEFAULT_8
	bool

config NR_CPUS_DEFAULT_16
	bool

config NR_CPUS_DEFAULT_32
	bool

config NR_CPUS_DEFAULT_64
	bool

L
Linus Torvalds 已提交
2096 2097
config NR_CPUS
	int "Maximum number of CPUs (2-64)"
2098
	range 1 64 if NR_CPUS_DEFAULT_1
L
Linus Torvalds 已提交
2099
	depends on SMP
2100
	default "1" if NR_CPUS_DEFAULT_1
2101 2102 2103 2104 2105 2106
	default "2" if NR_CPUS_DEFAULT_2
	default "4" if NR_CPUS_DEFAULT_4
	default "8" if NR_CPUS_DEFAULT_8
	default "16" if NR_CPUS_DEFAULT_16
	default "32" if NR_CPUS_DEFAULT_32
	default "64" if NR_CPUS_DEFAULT_64
L
Linus Torvalds 已提交
2107 2108 2109 2110
	help
	  This allows you to specify the maximum number of CPUs which this
	  kernel will support.  The maximum supported value is 32 for 32-bit
	  kernel and 64 for 64-bit kernels; the minimum value which makes
2111 2112
	  sense is 1 for Qemu (useful only for kernel debugging purposes)
	  and 2 for all others.
L
Linus Torvalds 已提交
2113 2114

	  This is purely to save memory - each supported CPU adds
2115 2116 2117
	  approximately eight kilobytes to the kernel image.  For best
	  performance should round up your number of processors to the next
	  power of two.
L
Linus Torvalds 已提交
2118

2119 2120
source "kernel/time/Kconfig"

2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131
#
# Timer Interrupt Frequency Configuration
#

choice
	prompt "Timer frequency"
	default HZ_250
	help
	 Allows the configuration of the timer frequency.

	config HZ_48
2132
		bool "48 HZ" if SYS_SUPPORTS_48HZ || SYS_SUPPORTS_ARBIT_HZ
2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191

	config HZ_100
		bool "100 HZ" if SYS_SUPPORTS_100HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_128
		bool "128 HZ" if SYS_SUPPORTS_128HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_250
		bool "250 HZ" if SYS_SUPPORTS_250HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_256
		bool "256 HZ" if SYS_SUPPORTS_256HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_1000
		bool "1000 HZ" if SYS_SUPPORTS_1000HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_1024
		bool "1024 HZ" if SYS_SUPPORTS_1024HZ || SYS_SUPPORTS_ARBIT_HZ

endchoice

config SYS_SUPPORTS_48HZ
	bool

config SYS_SUPPORTS_100HZ
	bool

config SYS_SUPPORTS_128HZ
	bool

config SYS_SUPPORTS_250HZ
	bool

config SYS_SUPPORTS_256HZ
	bool

config SYS_SUPPORTS_1000HZ
	bool

config SYS_SUPPORTS_1024HZ
	bool

config SYS_SUPPORTS_ARBIT_HZ
	bool
	default y if !SYS_SUPPORTS_48HZ && !SYS_SUPPORTS_100HZ && \
		     !SYS_SUPPORTS_128HZ && !SYS_SUPPORTS_250HZ && \
		     !SYS_SUPPORTS_256HZ && !SYS_SUPPORTS_1000HZ && \
		     !SYS_SUPPORTS_1024HZ

config HZ
	int
	default 48 if HZ_48
	default 100 if HZ_100
	default 128 if HZ_128
	default 250 if HZ_250
	default 256 if HZ_256
	default 1000 if HZ_1000
	default 1024 if HZ_1024

R
Ralf Baechle 已提交
2192
source "kernel/Kconfig.preempt"
L
Linus Torvalds 已提交
2193 2194 2195

config MIPS_INSANE_LARGE
	bool "Support for large 64-bit configurations"
2196
	depends on CPU_R10000 && 64BIT
L
Linus Torvalds 已提交
2197 2198 2199 2200 2201 2202 2203
	help
	  MIPS R10000 does support a 44 bit / 16TB address space as opposed to
	  previous 64-bit processors which only supported 40 bit / 1TB. If you
	  need processes of more than 1TB virtual address space, say Y here.
	  This will result in additional memory usage, so it is not
	  recommended for normal users.

2204 2205 2206 2207 2208 2209
config KEXEC
	bool "Kexec system call (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	help
	  kexec is a system call that implements the ability to shutdown your
	  current kernel, and to start another kernel.  It is like a reboot
2210
	  but it is independent of the system firmware.   And like a reboot
2211 2212
	  you can start any kernel with it, not just Linux.

M
Matt LaPlante 已提交
2213
	  The name comes from the similarity to the exec system call.
2214 2215 2216 2217 2218 2219 2220 2221 2222

	  It is an ongoing process to be certain the hardware in a machine
	  is properly shutdown, so do not be surprised if this code does not
	  initially work for you.  It may help to enable device hotplugging
	  support.  As of this writing the exact hardware interface is
	  strongly in flux, so no good recommendation can be made.

config SECCOMP
	bool "Enable seccomp to safely compute untrusted bytecode"
2223
	depends on PROC_FS
2224 2225 2226 2227 2228 2229 2230 2231 2232 2233 2234 2235 2236 2237
	default y
	help
	  This kernel feature is useful for number crunching applications
	  that may need to compute untrusted bytecode during their
	  execution. By using pipes or other transports made available to
	  the process as file descriptors supporting the read/write
	  syscalls, it's possible to isolate those applications in
	  their own address space using seccomp. Once seccomp is
	  enabled via /proc/<pid>/seccomp, it cannot be disabled
	  and the task is only allowed to execute a few safe syscalls
	  defined by each seccomp mode.

	  If unsure, say Y. Only embedded should say N here.

2238 2239 2240
config USE_OF
	bool "Flattened Device Tree support"
	select OF
2241
	select OF_EARLY_FLATTREE
2242 2243 2244
	help
	  Include support for flattened device tree machine descriptions.

2245 2246
endmenu

2247 2248 2249 2250 2251 2252 2253 2254
config LOCKDEP_SUPPORT
	bool
	default y

config STACKTRACE_SUPPORT
	bool
	default y

2255 2256
source "init/Kconfig"

2257 2258
source "kernel/Kconfig.freezer"

L
Linus Torvalds 已提交
2259 2260
menu "Bus options (PCI, PCMCIA, EISA, ISA, TC)"

2261 2262
config HW_HAS_EISA
	bool
L
Linus Torvalds 已提交
2263 2264 2265 2266 2267 2268
config HW_HAS_PCI
	bool

config PCI
	bool "Support for PCI controller"
	depends on HW_HAS_PCI
2269
	select PCI_DOMAINS
L
Linus Torvalds 已提交
2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290
	help
	  Find out whether you have a PCI motherboard. PCI is the name of a
	  bus system, i.e. the way the CPU talks to the other stuff inside
	  your box. Other bus systems are ISA, EISA, or VESA. If you have PCI,
	  say Y, otherwise N.

config PCI_DOMAINS
	bool

source "drivers/pci/Kconfig"

#
# ISA support is now enabled via select.  Too many systems still have the one
# or other ISA chip on the board that users don't know about so don't expect
# users to choose the right thing ...
#
config ISA
	bool

config EISA
	bool "EISA support"
2291
	depends on HW_HAS_EISA
L
Linus Torvalds 已提交
2292
	select ISA
2293
	select GENERIC_ISA_DMA
L
Linus Torvalds 已提交
2294 2295 2296 2297 2298 2299 2300 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312
	---help---
	  The Extended Industry Standard Architecture (EISA) bus was
	  developed as an open alternative to the IBM MicroChannel bus.

	  The EISA bus provided some of the features of the IBM MicroChannel
	  bus while maintaining backward compatibility with cards made for
	  the older ISA bus.  The EISA bus saw limited use between 1988 and
	  1995 when it was made obsolete by the PCI bus.

	  Say Y here if you are building a kernel for an EISA-based machine.

	  Otherwise, say N.

source "drivers/eisa/Kconfig"

config TC
	bool "TURBOchannel support"
	depends on MACH_DECSTATION
	help
2313 2314 2315 2316 2317 2318 2319 2320
	  TURBOchannel is a DEC (now Compaq (now HP)) bus for Alpha and MIPS
	  processors.  TURBOchannel programming specifications are available
	  at:
	  <ftp://ftp.hp.com/pub/alphaserver/archive/triadd/>
	  and:
	  <http://www.computer-refuge.org/classiccmp/ftp.digital.com/pub/DEC/TriAdd/>
	  Linux driver support status is documented at:
	  <http://www.linux-mips.org/wiki/DECstation>
L
Linus Torvalds 已提交
2321 2322 2323 2324 2325 2326 2327 2328 2329

#config ACCESSBUS
#	bool "Access.Bus support"
#	depends on TC

config MMU
	bool
	default y

2330 2331
config I8253
	bool
W
Wu Zhangjin 已提交
2332
	select MIPS_EXTERNAL_TIMER
2333

2334 2335 2336
config ZONE_DMA32
	bool

L
Linus Torvalds 已提交
2337 2338 2339 2340 2341 2342 2343 2344 2345 2346 2347 2348 2349 2350 2351
source "drivers/pcmcia/Kconfig"

source "drivers/pci/hotplug/Kconfig"

endmenu

menu "Executable file formats"

source "fs/Kconfig.binfmt"

config TRAD_SIGNALS
	bool

config MIPS32_COMPAT
	bool "Kernel support for Linux/MIPS 32-bit binary compatibility"
2352
	depends on 64BIT
L
Linus Torvalds 已提交
2353 2354 2355 2356 2357 2358 2359 2360 2361 2362
	help
	  Select this option if you want Linux/MIPS 32-bit binary
	  compatibility. Since all software available for Linux/MIPS is
	  currently 32-bit you should say Y here.

config COMPAT
	bool
	depends on MIPS32_COMPAT
	default y

2363 2364 2365 2366 2367
config SYSVIPC_COMPAT
	bool
	depends on COMPAT && SYSVIPC
	default y

L
Linus Torvalds 已提交
2368 2369 2370 2371 2372 2373 2374 2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385 2386 2387 2388 2389 2390 2391 2392
config MIPS32_O32
	bool "Kernel support for o32 binaries"
	depends on MIPS32_COMPAT
	help
	  Select this option if you want to run o32 binaries.  These are pure
	  32-bit binaries as used by the 32-bit Linux/MIPS port.  Most of
	  existing binaries are in this format.

	  If unsure, say Y.

config MIPS32_N32
	bool "Kernel support for n32 binaries"
	depends on MIPS32_COMPAT
	help
	  Select this option if you want to run n32 binaries.  These are
	  64-bit binaries using 32-bit quantities for addressing and certain
	  data that would normally be 64-bit.  They are used in special
	  cases.

	  If unsure, say N.

config BINFMT_ELF32
	bool
	default y if MIPS32_O32 || MIPS32_N32

2393 2394 2395 2396
endmenu

menu "Power management options"

W
Wu Zhangjin 已提交
2397 2398
config ARCH_HIBERNATION_POSSIBLE
	def_bool y
2399
	depends on SYS_SUPPORTS_HOTPLUG_CPU || !SMP
W
Wu Zhangjin 已提交
2400

J
Johannes Berg 已提交
2401 2402
config ARCH_SUSPEND_POSSIBLE
	def_bool y
2403
	depends on SYS_SUPPORTS_HOTPLUG_CPU || !SMP
J
Johannes Berg 已提交
2404

2405
source "kernel/power/Kconfig"
R
Rodolfo Giometti 已提交
2406

L
Linus Torvalds 已提交
2407 2408
endmenu

W
Wu Zhangjin 已提交
2409 2410
source "arch/mips/kernel/cpufreq/Kconfig"

2411 2412
source "net/Kconfig"

L
Linus Torvalds 已提交
2413 2414 2415 2416 2417 2418 2419 2420 2421 2422
source "drivers/Kconfig"

source "fs/Kconfig"

source "arch/mips/Kconfig.debug"

source "security/Kconfig"

source "crypto/Kconfig"

2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438
menuconfig VIRTUALIZATION
	bool "Virtualization"
	default n
	---help---
	  Say Y here to get to see options for using your Linux host to run other
	  operating systems inside virtual machines (guests).
	  This option alone does not add any kernel code.

	  If you say N, all options in this submenu will be skipped and disabled.

if VIRTUALIZATION

source drivers/virtio/Kconfig

endif # VIRTUALIZATION

L
Linus Torvalds 已提交
2439
source "lib/Kconfig"