Kconfig 56.8 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3
config MIPS
	bool
	default y
4
	select HAVE_GENERIC_DMA_COHERENT
S
Sam Ravnborg 已提交
5
	select HAVE_IDE
M
Mathieu Desnoyers 已提交
6
	select HAVE_OPROFILE
7 8
	select HAVE_PERF_EVENTS
	select PERF_USE_VMALLOC
9
	select HAVE_ARCH_KGDB
10
	select HAVE_FUNCTION_TRACER
11
	select HAVE_FUNCTION_TRACE_MCOUNT_TEST
12 13
	select HAVE_DYNAMIC_FTRACE
	select HAVE_FTRACE_MCOUNT_RECORD
14
	select HAVE_C_RECORDMCOUNT
15
	select HAVE_FUNCTION_GRAPH_TRACER
D
David Daney 已提交
16 17
	select HAVE_KPROBES
	select HAVE_KRETPROBES
18
	select RTC_LIB if !MACH_LOONGSON
19
	select GENERIC_ATOMIC64 if !64BIT
20 21
	select HAVE_DMA_ATTRS
	select HAVE_DMA_API_DEBUG
22 23
	select HAVE_GENERIC_HARDIRQS
	select GENERIC_IRQ_PROBE
24
	select HAVE_ARCH_JUMP_LABEL
L
Linus Torvalds 已提交
25 26 27

menu "Machine selection"

28 29 30
config ZONE_DMA
	bool

31 32 33
choice
	prompt "System type"
	default SGI_IP22
L
Linus Torvalds 已提交
34

35
config MIPS_ALCHEMY
36
	bool "Alchemy processor based machines"
37 38 39 40 41 42 43 44 45
	select 64BIT_PHYS_ADDR
	select CEVT_R4K_LIB
	select CSRC_R4K_LIB
	select IRQ_CPU
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_APM_EMULATION
	select GENERIC_GPIO
	select ARCH_WANT_OPTIONAL_GPIOLIB
46
	select SYS_SUPPORTS_ZBOOT
L
Linus Torvalds 已提交
47

48 49 50 51 52 53 54 55 56 57 58 59 60
config AR7
	bool "Texas Instruments AR7"
	select BOOT_ELF32
	select DMA_NONCOHERENT
	select CEVT_R4K
	select CSRC_R4K
	select IRQ_CPU
	select NO_EXCEPT_FILL
	select SWAP_IO_SPACE
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_EARLY_PRINTK
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
61
	select SYS_SUPPORTS_ZBOOT_UART16550
F
Florian Fainelli 已提交
62
	select ARCH_REQUIRE_GPIOLIB
63 64 65 66 67 68
	select GCD
	select VLYNQ
	help
	  Support for the Texas Instruments AR7 System-on-a-Chip
	  family: TNETD7100, 7200 and 7300.

69
config BCM47XX
70
	bool "Broadcom BCM47XX based boards"
71
	select CEVT_R4K
72
	select CSRC_R4K
73 74 75 76 77 78 79 80
	select DMA_NONCOHERENT
	select HW_HAS_PCI
	select IRQ_CPU
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
	select SSB
	select SSB_DRIVER_MIPS
81
	select SSB_DRIVER_EXTIF
82
	select SSB_EMBEDDED
83
	select SSB_B43_PCI_BRIDGE if PCI
84
	select SSB_PCICORE_HOSTMODE if PCI
85
	select GENERIC_GPIO
A
Aurelien Jarno 已提交
86 87
	select SYS_HAS_EARLY_PRINTK
	select CFE
88 89 90
	help
	 Support for BCM47XX based boards

91 92 93 94 95 96 97 98 99 100 101 102 103 104 105
config BCM63XX
	bool "Broadcom BCM63XX based boards"
	select CEVT_R4K
	select CSRC_R4K
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_HAS_EARLY_PRINTK
	select SWAP_IO_SPACE
	select ARCH_REQUIRE_GPIOLIB
	help
	 Support for BCM63XX based boards

L
Linus Torvalds 已提交
106
config MIPS_COBALT
107
	bool "Cobalt Server"
108
	select CEVT_R4K
109
	select CSRC_R4K
110
	select CEVT_GT641XX
L
Linus Torvalds 已提交
111 112
	select DMA_NONCOHERENT
	select HW_HAS_PCI
113
	select I8253
L
Linus Torvalds 已提交
114 115
	select I8259
	select IRQ_CPU
Y
Yoichi Yuasa 已提交
116
	select IRQ_GT641XX
117
	select PCI_GT64XXX_PCI0
118
	select PCI
119
	select SYS_HAS_CPU_NEVADA
Y
Yoichi Yuasa 已提交
120
	select SYS_HAS_EARLY_PRINTK
121
	select SYS_SUPPORTS_32BIT_KERNEL
122
	select SYS_SUPPORTS_64BIT_KERNEL
123
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
124 125

config MACH_DECSTATION
126
	bool "DECstations"
L
Linus Torvalds 已提交
127
	select BOOT_ELF32
128
	select CEVT_DS1287
129
	select CEVT_R4K
130
	select CSRC_IOASIC
131
	select CSRC_R4K
132 133 134
	select CPU_DADDI_WORKAROUNDS if 64BIT
	select CPU_R4000_WORKAROUNDS if 64BIT
	select CPU_R4400_WORKAROUNDS if 64BIT
L
Linus Torvalds 已提交
135
	select DMA_NONCOHERENT
136
	select NO_IOPORT
L
Linus Torvalds 已提交
137
	select IRQ_CPU
138 139
	select SYS_HAS_CPU_R3000
	select SYS_HAS_CPU_R4X00
140 141
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
142
	select SYS_SUPPORTS_LITTLE_ENDIAN
143 144 145
	select SYS_SUPPORTS_128HZ
	select SYS_SUPPORTS_256HZ
	select SYS_SUPPORTS_1024HZ
146
	help
L
Linus Torvalds 已提交
147 148 149 150 151 152 153
	  This enables support for DEC's MIPS based workstations.  For details
	  see the Linux/MIPS FAQ on <http://www.linux-mips.org/> and the
	  DECstation porting pages on <http://decstation.unix-ag.org/>.

	  If you have one of the following DECstation Models you definitely
	  want to choose R4xx0 for the CPU Type:

154 155 156 157
		DECstation 5000/50
		DECstation 5000/150
		DECstation 5000/260
		DECsystem 5900/260
L
Linus Torvalds 已提交
158 159 160

	  otherwise choose R3000.

161
config MACH_JAZZ
162
	bool "Jazz family of machines"
163 164 165
	select ARC
	select ARC32
	select ARCH_MAY_HAVE_PC_FDC
166
	select CEVT_R4K
167
	select CSRC_R4K
T
Thomas Bogendoerfer 已提交
168
	select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
169
	select GENERIC_ISA_DMA
T
Thomas Bogendoerfer 已提交
170
	select IRQ_CPU
171
	select I8253
172 173
	select I8259
	select ISA
174
	select SYS_HAS_CPU_R4X00
175 176
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
177
	select SYS_SUPPORTS_100HZ
L
Linus Torvalds 已提交
178
	help
179 180
	 This a family of machines based on the MIPS R4030 chipset which was
	 used by several vendors to build RISC/os and Windows NT workstations.
181
	 Members include the Acer PICA, MIPS Magnum 4000, MIPS Millennium and
182 183
	 Olivetti M700-10 workstations.

184 185 186 187 188 189 190 191 192 193 194 195
config MACH_JZ4740
	bool "Ingenic JZ4740 based machines"
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
	select DMA_NONCOHERENT
	select IRQ_CPU
	select GENERIC_GPIO
	select ARCH_REQUIRE_GPIOLIB
	select SYS_HAS_EARLY_PRINTK
	select HAVE_PWM

196 197
config LASAT
	bool "LASAT Networks platforms"
198
	select CEVT_R4K
199
	select CSRC_R4K
200 201 202
	select DMA_NONCOHERENT
	select SYS_HAS_EARLY_PRINTK
	select HW_HAS_PCI
203
	select IRQ_CPU
204 205 206 207 208 209 210 211
	select PCI_GT64XXX_PCI0
	select MIPS_NILE4
	select R5000_CPU_SCACHE
	select SYS_HAS_CPU_R5000
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL if BROKEN
	select SYS_SUPPORTS_LITTLE_ENDIAN

212 213
config MACH_LOONGSON
	bool "Loongson family of machines"
214
	select SYS_SUPPORTS_ZBOOT
215
	help
216 217 218 219 220 221
	  This enables the support of Loongson family of machines.

	  Loongson is a family of general-purpose MIPS-compatible CPUs.
	  developed at Institute of Computing Technology (ICT),
	  Chinese Academy of Sciences (CAS) in the People's Republic
	  of China. The chief architect is Professor Weiwu Hu.
222

L
Linus Torvalds 已提交
223
config MIPS_MALTA
224
	bool "MIPS Malta board"
225
	select ARCH_MAY_HAVE_PC_FDC
L
Linus Torvalds 已提交
226
	select BOOT_ELF32
227
	select BOOT_RAW
228
	select CEVT_R4K
229
	select CSRC_R4K
L
Linus Torvalds 已提交
230 231
	select DMA_NONCOHERENT
	select GENERIC_ISA_DMA
232
	select IRQ_CPU
233
	select IRQ_GIC
L
Linus Torvalds 已提交
234
	select HW_HAS_PCI
235
	select I8253
L
Linus Torvalds 已提交
236
	select I8259
237 238
	select MIPS_BOARDS_GEN
	select MIPS_BONITO64
239
	select MIPS_CPU_SCACHE
240
	select PCI_GT64XXX_PCI0
241
	select MIPS_MSC
L
Linus Torvalds 已提交
242
	select SWAP_IO_SPACE
243 244 245 246 247
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_HAS_CPU_MIPS64_R1
	select SYS_HAS_CPU_NEVADA
	select SYS_HAS_CPU_RM7000
248
	select SYS_HAS_EARLY_PRINTK
249 250
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
251 252
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN
T
Tim Anderson 已提交
253
	select SYS_SUPPORTS_MIPS_CMP
254
	select SYS_SUPPORTS_MULTITHREADING
255
	select SYS_SUPPORTS_SMARTMIPS
256
	select SYS_SUPPORTS_ZBOOT
L
Linus Torvalds 已提交
257
	help
258
	  This enables support for the MIPS Technologies Malta evaluation
L
Linus Torvalds 已提交
259 260
	  board.

261
config MIPS_SIM
262
	bool 'MIPS simulator (MIPSsim)'
263
	select CEVT_R4K
264
	select CSRC_R4K
L
Linus Torvalds 已提交
265
	select DMA_NONCOHERENT
266
	select SYS_HAS_EARLY_PRINTK
L
Linus Torvalds 已提交
267
	select IRQ_CPU
M
Marc St-Jean 已提交
268
	select BOOT_RAW
269 270
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_CPU_MIPS32_R2
271
	select SYS_HAS_EARLY_PRINTK
272
	select SYS_SUPPORTS_32BIT_KERNEL
273
	select SYS_SUPPORTS_BIG_ENDIAN
274
	select SYS_SUPPORTS_MULTITHREADING
275
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
276
	help
277 278
	  This option enables support for MIPS Technologies MIPSsim software
	  emulator.
L
Linus Torvalds 已提交
279

280 281 282 283 284 285
config NEC_MARKEINS
	bool "NEC EMMA2RH Mark-eins board"
	select SOC_EMMA2RH
	select HW_HAS_PCI
	help
	  This enables support for the NEC Electronics Mark-eins boards.
286

287
config MACH_VR41XX
288
	bool "NEC VR4100 series based machines"
289
	select CEVT_R4K
290
	select CSRC_R4K
291
	select SYS_HAS_CPU_VR41XX
292
	select ARCH_REQUIRE_GPIOLIB
293

294 295 296 297 298 299 300 301 302 303 304 305 306
config NXP_STB220
	bool "NXP STB220 board"
	select SOC_PNX833X
	help
	 Support for NXP Semiconductors STB220 Development Board.

config NXP_STB225
	bool "NXP 225 board"
	select SOC_PNX833X
	select SOC_PNX8335
	help
	 Support for NXP Semiconductors STB225 Development Board.

307
config PNX8550_JBS
308
	bool "NXP PNX8550 based JBS board"
309 310 311 312
	select PNX8550
	select SYS_SUPPORTS_LITTLE_ENDIAN

config PNX8550_STB810
313
	bool "NXP PNX8550 based STB810 board"
314 315 316
	select PNX8550
	select SYS_SUPPORTS_LITTLE_ENDIAN

M
Marc St-Jean 已提交
317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336
config PMC_MSP
	bool "PMC-Sierra MSP chipsets"
	depends on EXPERIMENTAL
	select DMA_NONCOHERENT
	select SWAP_IO_SPACE
	select NO_EXCEPT_FILL
	select BOOT_RAW
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select IRQ_CPU
	select SERIAL_8250
	select SERIAL_8250_CONSOLE
	help
	  This adds support for the PMC-Sierra family of Multi-Service
	  Processor System-On-A-Chips.  These parts include a number
	  of integrated peripherals, interfaces and DSPs in addition to
	  a variety of MIPS cores.

337
config PMC_YOSEMITE
338
	bool "PMC-Sierra Yosemite eval board"
339
	select CEVT_R4K
340
	select CSRC_R4K
341 342 343 344 345 346
	select DMA_COHERENT
	select HW_HAS_PCI
	select IRQ_CPU
	select IRQ_CPU_RM7K
	select IRQ_CPU_RM9K
	select SWAP_IO_SPACE
347
	select SYS_HAS_CPU_RM9000
348
	select SYS_HAS_EARLY_PRINTK
349 350 351 352
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
353
	select SYS_SUPPORTS_SMP
354 355 356
	help
	  Yosemite is an evaluation board for the RM9000x2 processor
	  manufactured by PMC-Sierra.
L
Linus Torvalds 已提交
357

358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375
config POWERTV
	bool "Cisco PowerTV"
	select BOOT_ELF32
	select CEVT_R4K
	select CPU_MIPSR2_IRQ_VI
	select CPU_MIPSR2_IRQ_EI
	select CSRC_POWERTV
	select DMA_NONCOHERENT
	select HW_HAS_PCI
	select SYS_HAS_EARLY_PRINTK
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
	select USB_OHCI_LITTLE_ENDIAN
	help
	  This enables support for the Cisco PowerTV Platform.

L
Linus Torvalds 已提交
376
config SGI_IP22
377
	bool "SGI IP22 (Indy/Indigo2)"
L
Linus Torvalds 已提交
378 379 380
	select ARC
	select ARC32
	select BOOT_ELF32
381
	select CEVT_R4K
382
	select CSRC_R4K
T
Thomas Bogendoerfer 已提交
383
	select DEFAULT_SGI_PARTITION
L
Linus Torvalds 已提交
384
	select DMA_NONCOHERENT
385
	select HW_HAS_EISA
386
	select I8253
387
	select I8259
L
Linus Torvalds 已提交
388 389
	select IP22_CPU_SCACHE
	select IRQ_CPU
390
	select GENERIC_ISA_DMA_SUPPORT_BROKEN
T
Thomas Bogendoerfer 已提交
391 392
	select SGI_HAS_I8042
	select SGI_HAS_INDYDOG
393
	select SGI_HAS_HAL2
T
Thomas Bogendoerfer 已提交
394 395 396
	select SGI_HAS_SEEQ
	select SGI_HAS_WD93
	select SGI_HAS_ZILOG
L
Linus Torvalds 已提交
397
	select SWAP_IO_SPACE
398 399
	select SYS_HAS_CPU_R4X00
	select SYS_HAS_CPU_R5000
400 401 402 403 404 405 406 407
	#
	# Disable EARLY_PRINTK for now since it leads to overwritten prom
	# memory during early boot on some machines.
	#
	# See http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=20091119164009.GA15038%40deprecation.cyrius.com
	# for a more details discussion
	#
	# select SYS_HAS_EARLY_PRINTK
408 409
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
410
	select SYS_SUPPORTS_BIG_ENDIAN
L
Linus Torvalds 已提交
411 412 413 414 415 416
	help
	  This are the SGI Indy, Challenge S and Indigo2, as well as certain
	  OEM variants like the Tandem CMN B006S. To compile a Linux kernel
	  that runs on these, say Y here.

config SGI_IP27
417
	bool "SGI IP27 (Origin200/2000)"
L
Linus Torvalds 已提交
418 419
	select ARC
	select ARC64
420
	select BOOT_ELF64
T
Thomas Bogendoerfer 已提交
421
	select DEFAULT_SGI_PARTITION
422
	select DMA_COHERENT
423
	select SYS_HAS_EARLY_PRINTK
L
Linus Torvalds 已提交
424
	select HW_HAS_PCI
425
	select NR_CPUS_DEFAULT_64
426
	select SYS_HAS_CPU_R10000
427
	select SYS_SUPPORTS_64BIT_KERNEL
428
	select SYS_SUPPORTS_BIG_ENDIAN
429
	select SYS_SUPPORTS_NUMA
430
	select SYS_SUPPORTS_SMP
L
Linus Torvalds 已提交
431 432 433 434 435
	help
	  This are the SGI Origin 200, Origin 2000 and Onyx 2 Graphics
	  workstations.  To compile a Linux kernel that runs on these, say Y
	  here.

T
Thomas Bogendoerfer 已提交
436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452
config SGI_IP28
	bool "SGI IP28 (Indigo2 R10k) (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	select ARC
	select ARC64
	select BOOT_ELF64
	select CEVT_R4K
	select CSRC_R4K
	select DEFAULT_SGI_PARTITION
	select DMA_NONCOHERENT
	select GENERIC_ISA_DMA_SUPPORT_BROKEN
	select IRQ_CPU
	select HW_HAS_EISA
	select I8253
	select I8259
	select SGI_HAS_I8042
	select SGI_HAS_INDYDOG
453
	select SGI_HAS_HAL2
T
Thomas Bogendoerfer 已提交
454 455 456 457 458
	select SGI_HAS_SEEQ
	select SGI_HAS_WD93
	select SGI_HAS_ZILOG
	select SWAP_IO_SPACE
	select SYS_HAS_CPU_R10000
459 460 461 462 463 464 465 466
	#
	# Disable EARLY_PRINTK for now since it leads to overwritten prom
	# memory during early boot on some machines.
	#
	# See http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=20091119164009.GA15038%40deprecation.cyrius.com
	# for a more details discussion
	#
	# select SYS_HAS_EARLY_PRINTK
T
Thomas Bogendoerfer 已提交
467 468 469 470 471 472
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
      help
        This is the SGI Indigo2 with R10000 processor.  To compile a Linux
        kernel that runs on these, say Y here.

L
Linus Torvalds 已提交
473
config SGI_IP32
474
	bool "SGI IP32 (O2)"
L
Linus Torvalds 已提交
475 476 477
	select ARC
	select ARC32
	select BOOT_ELF32
478
	select CEVT_R4K
479
	select CSRC_R4K
L
Linus Torvalds 已提交
480 481
	select DMA_NONCOHERENT
	select HW_HAS_PCI
482
	select IRQ_CPU
L
Linus Torvalds 已提交
483 484
	select R5000_CPU_SCACHE
	select RM7000_CPU_SCACHE
485 486 487
	select SYS_HAS_CPU_R5000
	select SYS_HAS_CPU_R10000 if BROKEN
	select SYS_HAS_CPU_RM7000
R
Ralf Baechle 已提交
488
	select SYS_HAS_CPU_NEVADA
489
	select SYS_SUPPORTS_64BIT_KERNEL
490 491
	select SYS_SUPPORTS_BIG_ENDIAN
	help
492
	  If you want this kernel to run on SGI O2 workstation, say Y here.
L
Linus Torvalds 已提交
493

494 495 496
config SIBYTE_CRHINE
	bool "Sibyte BCM91120C-CRhine"
	depends on EXPERIMENTAL
A
Andrew Isaacson 已提交
497 498
	select BOOT_ELF32
	select DMA_COHERENT
499
	select SIBYTE_BCM1120
A
Andrew Isaacson 已提交
500
	select SWAP_IO_SPACE
501
	select SYS_HAS_CPU_SB1
A
Andrew Isaacson 已提交
502 503 504
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN

505 506 507
config SIBYTE_CARMEL
	bool "Sibyte BCM91120x-Carmel"
	depends on EXPERIMENTAL
508
	select BOOT_ELF32
L
Linus Torvalds 已提交
509
	select DMA_COHERENT
510
	select SIBYTE_BCM1120
511
	select SWAP_IO_SPACE
512
	select SYS_HAS_CPU_SB1
513
	select SYS_SUPPORTS_BIG_ENDIAN
514
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
515

516 517
config SIBYTE_CRHONE
	bool "Sibyte BCM91125C-CRhone"
518 519 520
	depends on EXPERIMENTAL
	select BOOT_ELF32
	select DMA_COHERENT
521
	select SIBYTE_BCM1125
522
	select SWAP_IO_SPACE
523
	select SYS_HAS_CPU_SB1
524
	select SYS_SUPPORTS_BIG_ENDIAN
525
	select SYS_SUPPORTS_HIGHMEM
526
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
527

528
config SIBYTE_RHONE
529
	bool "Sibyte BCM91125E-Rhone"
530 531 532 533 534
	depends on EXPERIMENTAL
	select BOOT_ELF32
	select DMA_COHERENT
	select SIBYTE_BCM1125H
	select SWAP_IO_SPACE
535
	select SYS_HAS_CPU_SB1
536 537
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
538

539 540
config SIBYTE_SWARM
	bool "Sibyte BCM91250A-SWARM"
541
	select BOOT_ELF32
P
Pete Popov 已提交
542
	select DMA_COHERENT
543
	select HAVE_PATA_PLATFORM
544 545
	select NR_CPUS_DEFAULT_2
	select SIBYTE_SB1250
546
	select SWAP_IO_SPACE
547
	select SYS_HAS_CPU_SB1
548
	select SYS_SUPPORTS_BIG_ENDIAN
549
	select SYS_SUPPORTS_HIGHMEM
P
Pete Popov 已提交
550
	select SYS_SUPPORTS_LITTLE_ENDIAN
551
	select ZONE_DMA32 if 64BIT
P
Pete Popov 已提交
552

553 554
config SIBYTE_LITTLESUR
	bool "Sibyte BCM91250C2-LittleSur"
555 556 557
	depends on EXPERIMENTAL
	select BOOT_ELF32
	select DMA_COHERENT
558
	select HAVE_PATA_PLATFORM
559
	select NR_CPUS_DEFAULT_2
560 561
	select SIBYTE_SB1250
	select SWAP_IO_SPACE
562
	select SYS_HAS_CPU_SB1
563 564 565
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
566

567 568
config SIBYTE_SENTOSA
	bool "Sibyte BCM91250E-Sentosa"
569 570 571
	depends on EXPERIMENTAL
	select BOOT_ELF32
	select DMA_COHERENT
572
	select NR_CPUS_DEFAULT_2
573 574
	select SIBYTE_SB1250
	select SWAP_IO_SPACE
575
	select SYS_HAS_CPU_SB1
576 577
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
578

579 580
config SIBYTE_BIGSUR
	bool "Sibyte BCM91480B-BigSur"
581 582
	select BOOT_ELF32
	select DMA_COHERENT
583 584
	select NR_CPUS_DEFAULT_4
	select SIBYTE_BCM1x80
585
	select SWAP_IO_SPACE
586
	select SYS_HAS_CPU_SB1
587
	select SYS_SUPPORTS_BIG_ENDIAN
R
Ralf Baechle 已提交
588
	select SYS_SUPPORTS_HIGHMEM
589
	select SYS_SUPPORTS_LITTLE_ENDIAN
590
	select ZONE_DMA32 if 64BIT
L
Linus Torvalds 已提交
591

592 593
config SNI_RM
	bool "SNI RM200/300/400"
594 595
	select ARC if CPU_LITTLE_ENDIAN
	select ARC32 if CPU_LITTLE_ENDIAN
596
	select SNIPROM if CPU_BIG_ENDIAN
597
	select ARCH_MAY_HAVE_PC_FDC
L
Linus Torvalds 已提交
598
	select BOOT_ELF32
599
	select CEVT_R4K
600
	select CSRC_R4K
T
Thomas Bogendoerfer 已提交
601
	select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
L
Linus Torvalds 已提交
602 603
	select DMA_NONCOHERENT
	select GENERIC_ISA_DMA
604
	select HW_HAS_EISA
L
Linus Torvalds 已提交
605
	select HW_HAS_PCI
606
	select IRQ_CPU
607
	select I8253
L
Linus Torvalds 已提交
608 609
	select I8259
	select ISA
610
	select SWAP_IO_SPACE if CPU_BIG_ENDIAN
611
	select SYS_HAS_CPU_R4X00
612
	select SYS_HAS_CPU_R5000
613
	select SYS_HAS_CPU_R10000
614
	select R5000_CPU_SCACHE
615
	select SYS_HAS_EARLY_PRINTK
616 617
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
618
	select SYS_SUPPORTS_BIG_ENDIAN
R
Ralf Baechle 已提交
619
	select SYS_SUPPORTS_HIGHMEM
620
	select SYS_SUPPORTS_LITTLE_ENDIAN
L
Linus Torvalds 已提交
621
	help
622 623
	  The SNI RM200/300/400 are MIPS-based machines manufactured by
	  Siemens Nixdorf Informationssysteme (SNI), parent company of Pyramid
L
Linus Torvalds 已提交
624 625 626
	  Technology and now in turn merged with Fujitsu.  Say Y here to
	  support this machine type.

627 628
config MACH_TX39XX
	bool "Toshiba TX39 series based machines"
629

630 631
config MACH_TX49XX
	bool "Toshiba TX49 series based machines"
632

633 634 635 636 637 638 639 640 641 642 643 644
config MIKROTIK_RB532
	bool "Mikrotik RB532 boards"
	select CEVT_R4K
	select CSRC_R4K
	select DMA_NONCOHERENT
	select HW_HAS_PCI
	select IRQ_CPU
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
	select SWAP_IO_SPACE
	select BOOT_RAW
645
	select ARCH_REQUIRE_GPIOLIB
646 647 648 649
	help
	  Support the Mikrotik(tm) RouterBoard 532 series,
	  based on the IDT RC32434 SoC.

650 651
config WR_PPMC
	bool "Wind River PPMC board"
652
	select CEVT_R4K
653
	select CSRC_R4K
654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672
	select IRQ_CPU
	select BOOT_ELF32
	select DMA_NONCOHERENT
	select HW_HAS_PCI
	select PCI_GT64XXX_PCI0
	select SWAP_IO_SPACE
	select SYS_HAS_CPU_MIPS32_R1
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_HAS_CPU_MIPS64_R1
	select SYS_HAS_CPU_NEVADA
	select SYS_HAS_CPU_RM7000
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_LITTLE_ENDIAN
	help
	  This enables support for the Wind River MIPS32 4KC PPMC evaluation
	  board, which is based on GT64120 bridge chip.

673
config CAVIUM_OCTEON_SIMULATOR
674
	bool "Cavium Networks Octeon Simulator"
675 676 677 678 679 680
	select CEVT_R4K
	select 64BIT_PHYS_ADDR
	select DMA_COHERENT
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
681
	select SYS_SUPPORTS_HOTPLUG_CPU
682
	select SYS_HAS_CPU_CAVIUM_OCTEON
683 684 685 686 687 688
	help
	  The Octeon simulator is software performance model of the Cavium
	  Octeon Processor. It supports simulating Octeon processors on x86
	  hardware.

config CAVIUM_OCTEON_REFERENCE_BOARD
689
	bool "Cavium Networks Octeon reference board"
690 691 692 693 694 695
	select CEVT_R4K
	select 64BIT_PHYS_ADDR
	select DMA_COHERENT
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN
	select SYS_SUPPORTS_HIGHMEM
696
	select SYS_SUPPORTS_HOTPLUG_CPU
697
	select SYS_HAS_EARLY_PRINTK
698
	select SYS_HAS_CPU_CAVIUM_OCTEON
699
	select SWAP_IO_SPACE
700 701
	select HW_HAS_PCI
	select ARCH_SUPPORTS_MSI
D
David Daney 已提交
702
	select ZONE_DMA32
703 704
	select USB_ARCH_HAS_OHCI
	select USB_ARCH_HAS_EHCI
705 706 707 708 709 710 711 712 713 714 715 716 717
	help
	  This option supports all of the Octeon reference boards from Cavium
	  Networks. It builds a kernel that dynamically determines the Octeon
	  CPU type and supports all known board reference implementations.
	  Some of the supported boards are:
		EBT3000
		EBH3000
		EBH3100
		Thunder
		Kodama
		Hikari
	  Say Y here for most Octeon reference boards.

718
endchoice
L
Linus Torvalds 已提交
719

R
Ralf Baechle 已提交
720
source "arch/mips/alchemy/Kconfig"
721
source "arch/mips/bcm63xx/Kconfig"
722
source "arch/mips/jazz/Kconfig"
723
source "arch/mips/jz4740/Kconfig"
724
source "arch/mips/lasat/Kconfig"
725
source "arch/mips/pmc-sierra/Kconfig"
726
source "arch/mips/powertv/Kconfig"
727
source "arch/mips/sgi-ip27/Kconfig"
728
source "arch/mips/sibyte/Kconfig"
A
Atsushi Nemoto 已提交
729
source "arch/mips/txx9/Kconfig"
730
source "arch/mips/vr41xx/Kconfig"
731
source "arch/mips/cavium-octeon/Kconfig"
732
source "arch/mips/loongson/Kconfig"
733

734 735
endmenu

L
Linus Torvalds 已提交
736 737 738 739 740 741 742
config RWSEM_GENERIC_SPINLOCK
	bool
	default y

config RWSEM_XCHGADD_ALGORITHM
	bool

743 744 745 746 747 748 749 750
config ARCH_HAS_ILOG2_U32
	bool
	default n

config ARCH_HAS_ILOG2_U64
	bool
	default n

R
Ralf Baechle 已提交
751 752 753 754
config ARCH_SUPPORTS_OPROFILE
	bool
	default y if !MIPS_MT_SMTC

755 756 757 758 759 760 761 762
config GENERIC_FIND_NEXT_BIT
	bool
	default y

config GENERIC_HWEIGHT
	bool
	default y

L
Linus Torvalds 已提交
763 764 765 766
config GENERIC_CALIBRATE_DELAY
	bool
	default y

767 768 769 770
config GENERIC_CLOCKEVENTS
	bool
	default y

771 772 773 774
config GENERIC_CMOS_UPDATE
	bool
	default y

775
config SCHED_OMIT_FRAME_POINTER
776 777 778
	bool
	default y

779
config GENERIC_HARDIRQS_NO__DO_IRQ
780
	def_bool y
781

L
Linus Torvalds 已提交
782 783 784 785 786 787
#
# Select some configuration options automatically based on user selections.
#
config ARC
	bool

788 789 790
config ARCH_MAY_HAVE_PC_FDC
	bool

M
Marc St-Jean 已提交
791 792 793
config BOOT_RAW
	bool

794 795 796
config CEVT_BCM1480
	bool

797 798 799
config CEVT_DS1287
	bool

800 801 802
config CEVT_GT641XX
	bool

803 804 805
config CEVT_R4K_LIB
	bool

806
config CEVT_R4K
807
	select CEVT_R4K_LIB
808 809
	bool

810 811 812
config CEVT_SB1250
	bool

813 814 815
config CEVT_TXX9
	bool

816 817 818
config CSRC_BCM1480
	bool

819 820 821
config CSRC_IOASIC
	bool

822 823 824
config CSRC_POWERTV
	bool

825 826 827
config CSRC_R4K_LIB
	bool

828
config CSRC_R4K
829
	select CSRC_R4K_LIB
830 831
	bool

832 833 834
config CSRC_SB1250
	bool

835 836
config GPIO_TXX9
	select GENERIC_GPIO
M
Michael Buesch 已提交
837
	select ARCH_REQUIRE_GPIOLIB
838 839
	bool

840 841 842
config CFE
	bool

843
config DMA_COHERENT
L
Linus Torvalds 已提交
844 845
	bool

846 847
config DMA_NONCOHERENT
	bool
848
	select NEED_DMA_MAP_STATE
849

850
config NEED_DMA_MAP_STATE
L
Linus Torvalds 已提交
851 852
	bool

853
config SYS_HAS_EARLY_PRINTK
L
Linus Torvalds 已提交
854 855
	bool

856
config HOTPLUG_CPU
857 858 859 860 861 862 863 864 865 866
	bool "Support for hot-pluggable CPUs"
	depends on SMP && HOTPLUG && SYS_SUPPORTS_HOTPLUG_CPU
	help
	  Say Y here to allow turning CPUs off and on. CPUs can be
	  controlled through /sys/devices/system/cpu.
	  (Note: power management support will enable this option
	    automatically on SMP systems. )
	  Say N if you want to disable CPU hotplug.

config SYS_SUPPORTS_HOTPLUG_CPU
867 868
	bool

L
Linus Torvalds 已提交
869 870 871 872 873 874 875 876 877
config I8259
	bool

config MIPS_BONITO64
	bool

config MIPS_MSC
	bool

878 879 880
config MIPS_NILE4
	bool

L
Linus Torvalds 已提交
881 882 883
config MIPS_DISABLE_OBSOLETE_IDE
	bool

884 885 886
config SYNC_R4K
	bool

887 888 889
config MIPS_MACHINE
	def_bool n

890 891 892
config NO_IOPORT
	def_bool n

893 894 895
config GENERIC_ISA_DMA
	bool
	select ZONE_DMA if GENERIC_ISA_DMA_SUPPORT_BROKEN=n
896
	select ISA_DMA_API
897

898 899
config GENERIC_ISA_DMA_SUPPORT_BROKEN
	bool
900
	select GENERIC_ISA_DMA
901

902 903 904
config ISA_DMA_API
	bool

Y
Yoichi Yuasa 已提交
905 906 907
config GENERIC_GPIO
	bool

908
#
M
Matt LaPlante 已提交
909
# Endianess selection.  Sufficiently obscure so many users don't know what to
910 911 912 913 914
# answer,so we try hard to limit the available choices.  Also the use of a
# choice statement should be more obvious to the user.
#
choice
	prompt "Endianess selection"
L
Linus Torvalds 已提交
915 916
	help
	  Some MIPS machines can be configured for either little or big endian
917
	  byte order. These modes require different kernels and a different
M
Matt LaPlante 已提交
918
	  Linux distribution.  In general there is one preferred byteorder for a
919
	  particular system but some systems are just as commonly used in the
920
	  one or the other endianness.
921 922 923 924 925 926 927 928 929 930 931 932

config CPU_BIG_ENDIAN
	bool "Big endian"
	depends on SYS_SUPPORTS_BIG_ENDIAN

config CPU_LITTLE_ENDIAN
	bool "Little endian"
	depends on SYS_SUPPORTS_LITTLE_ENDIAN
	help

endchoice

933 934 935
config EXPORT_UASM
	bool

936 937 938
config SYS_SUPPORTS_APM_EMULATION
	bool

939 940 941 942 943
config SYS_SUPPORTS_BIG_ENDIAN
	bool

config SYS_SUPPORTS_LITTLE_ENDIAN
	bool
L
Linus Torvalds 已提交
944

945 946 947 948 949
config SYS_SUPPORTS_HUGETLBFS
	bool
	depends on CPU_SUPPORTS_HUGEPAGES && 64BIT
	default y

L
Linus Torvalds 已提交
950 951 952 953 954 955
config IRQ_CPU
	bool

config IRQ_CPU_RM7K
	bool

956 957 958
config IRQ_CPU_RM9K
	bool

M
Marc St-Jean 已提交
959 960 961 962 963 964
config IRQ_MSP_SLP
	bool

config IRQ_MSP_CIC
	bool

965 966 967
config IRQ_TXX9
	bool

Y
Yoichi Yuasa 已提交
968 969 970
config IRQ_GT641XX
	bool

971 972 973
config IRQ_GIC
	bool

974 975 976
config IRQ_CPU_OCTEON
	bool

L
Linus Torvalds 已提交
977 978 979
config MIPS_BOARDS_GEN
	bool

980
config PCI_GT64XXX_PCI0
L
Linus Torvalds 已提交
981 982
	bool

M
Marc St-Jean 已提交
983 984 985
config NO_EXCEPT_FILL
	bool

986 987 988 989
config MIPS_RM9122
	bool
	select SERIAL_RM9000

990 991 992 993 994 995 996 997 998 999 1000 1001
config SOC_EMMA2RH
	bool
	select CEVT_R4K
	select CSRC_R4K
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_HAS_CPU_R5500
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_BIG_ENDIAN

1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018
config SOC_PNX833X
	bool
	select CEVT_R4K
	select CSRC_R4K
	select IRQ_CPU
	select DMA_NONCOHERENT
	select SYS_HAS_CPU_MIPS32_R2
	select SYS_SUPPORTS_32BIT_KERNEL
	select SYS_SUPPORTS_LITTLE_ENDIAN
	select SYS_SUPPORTS_BIG_ENDIAN
	select GENERIC_GPIO
	select CPU_MIPSR2_IRQ_VI

config SOC_PNX8335
	bool
	select SOC_PNX833X

1019 1020 1021 1022 1023 1024 1025 1026
config PNX8550
	bool
	select SOC_PNX8550

config SOC_PNX8550
	bool
	select DMA_NONCOHERENT
	select HW_HAS_PCI
1027
	select SYS_HAS_CPU_MIPS32_R1
1028
	select SYS_HAS_EARLY_PRINTK
1029
	select SYS_SUPPORTS_32BIT_KERNEL
1030
	select GENERIC_GPIO
1031

L
Linus Torvalds 已提交
1032 1033 1034
config SWAP_IO_SPACE
	bool

1035 1036 1037
config SERIAL_RM9000
	bool

T
Thomas Bogendoerfer 已提交
1038 1039 1040
config SGI_HAS_INDYDOG
	bool

1041 1042 1043
config SGI_HAS_HAL2
	bool

T
Thomas Bogendoerfer 已提交
1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058
config SGI_HAS_SEEQ
	bool

config SGI_HAS_WD93
	bool

config SGI_HAS_ZILOG
	bool

config SGI_HAS_I8042
	bool

config DEFAULT_SGI_PARTITION
	bool

1059 1060 1061
config ARC32
	bool

1062 1063 1064
config SNIPROM
	bool

L
Linus Torvalds 已提交
1065 1066 1067 1068 1069
config BOOT_ELF32
	bool

config MIPS_L1_CACHE_SHIFT
	int
1070
	default "4" if MACH_DECSTATION || MIKROTIK_RB532 || PMC_MSP4200_EVAL
1071
	default "6" if MIPS_CPU_SCACHE
1072
	default "7" if SGI_IP22 || SGI_IP27 || SGI_IP28 || SNI_RM || CPU_CAVIUM_OCTEON
L
Linus Torvalds 已提交
1073 1074 1075 1076 1077 1078 1079
	default "5"

config HAVE_STD_PC_SERIAL_PORT
	bool

config ARC_CONSOLE
	bool "ARC console support"
T
Thomas Bogendoerfer 已提交
1080
	depends on SGI_IP22 || SGI_IP28 || (SNI_RM && CPU_LITTLE_ENDIAN)
L
Linus Torvalds 已提交
1081 1082 1083

config ARC_MEMORY
	bool
1084
	depends on MACH_JAZZ || SNI_RM || SGI_IP32
L
Linus Torvalds 已提交
1085 1086 1087 1088
	default y

config ARC_PROMLIB
	bool
T
Thomas Bogendoerfer 已提交
1089
	depends on MACH_JAZZ || SNI_RM || SGI_IP22 || SGI_IP28 || SGI_IP32
L
Linus Torvalds 已提交
1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103
	default y

config ARC64
	bool

config BOOT_ELF64
	bool

menu "CPU selection"

choice
	prompt "CPU type"
	default CPU_R4X00

1104 1105 1106 1107
config CPU_LOONGSON2E
	bool "Loongson 2E"
	depends on SYS_HAS_CPU_LOONGSON2E
	select CPU_LOONGSON2
1108 1109 1110 1111
	help
	  The Loongson 2E processor implements the MIPS III instruction set
	  with many extensions.

1112 1113 1114 1115 1116 1117 1118
	  It has an internal FPGA northbridge, which is compatiable to
	  bonito64.

config CPU_LOONGSON2F
	bool "Loongson 2F"
	depends on SYS_HAS_CPU_LOONGSON2F
	select CPU_LOONGSON2
1119 1120
	select GENERIC_GPIO
	select ARCH_REQUIRE_GPIOLIB
1121 1122 1123 1124 1125 1126 1127 1128
	help
	  The Loongson 2F processor implements the MIPS III instruction set
	  with many extensions.

	  Loongson2F have built-in DDR2 and PCIX controller. The PCIX controller
	  have a similar programming interface with FPGA northbridge used in
	  Loongson2E.

1129 1130
config CPU_MIPS32_R1
	bool "MIPS32 Release 1"
1131
	depends on SYS_HAS_CPU_MIPS32_R1
1132
	select CPU_HAS_PREFETCH
R
Ralf Baechle 已提交
1133
	select CPU_SUPPORTS_32BIT_KERNEL
1134
	select CPU_SUPPORTS_HIGHMEM
R
Ralf Baechle 已提交
1135
	help
1136
	  Choose this option to build a kernel for release 1 or later of the
R
Ralf Baechle 已提交
1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147
	  MIPS32 architecture.  Most modern embedded systems with a 32-bit
	  MIPS processor are based on a MIPS32 processor.  If you know the
	  specific type of processor in your system, choose those that one
	  otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.
	  Release 2 of the MIPS32 architecture is available since several
	  years so chances are you even have a MIPS32 Release 2 processor
	  in which case you should choose CPU_MIPS32_R2 instead for better
	  performance.

config CPU_MIPS32_R2
	bool "MIPS32 Release 2"
1148
	depends on SYS_HAS_CPU_MIPS32_R2
R
Ralf Baechle 已提交
1149
	select CPU_HAS_PREFETCH
R
Ralf Baechle 已提交
1150
	select CPU_SUPPORTS_32BIT_KERNEL
1151
	select CPU_SUPPORTS_HIGHMEM
1152
	help
1153
	  Choose this option to build a kernel for release 2 or later of the
1154 1155 1156 1157 1158 1159 1160
	  MIPS32 architecture.  Most modern embedded systems with a 32-bit
	  MIPS processor are based on a MIPS32 processor.  If you know the
	  specific type of processor in your system, choose those that one
	  otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.

config CPU_MIPS64_R1
	bool "MIPS64 Release 1"
1161
	depends on SYS_HAS_CPU_MIPS64_R1
R
Ralf Baechle 已提交
1162
	select CPU_HAS_PREFETCH
1163 1164
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
1165
	select CPU_SUPPORTS_HIGHMEM
1166
	select CPU_SUPPORTS_HUGEPAGES
1167 1168 1169 1170 1171 1172
	help
	  Choose this option to build a kernel for release 1 or later of the
	  MIPS64 architecture.  Many modern embedded systems with a 64-bit
	  MIPS processor are based on a MIPS64 processor.  If you know the
	  specific type of processor in your system, choose those that one
	  otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
R
Ralf Baechle 已提交
1173 1174 1175 1176 1177 1178 1179
	  Release 2 of the MIPS64 architecture is available since several
	  years so chances are you even have a MIPS64 Release 2 processor
	  in which case you should choose CPU_MIPS64_R2 instead for better
	  performance.

config CPU_MIPS64_R2
	bool "MIPS64 Release 2"
1180
	depends on SYS_HAS_CPU_MIPS64_R2
R
Ralf Baechle 已提交
1181
	select CPU_HAS_PREFETCH
R
Ralf Baechle 已提交
1182 1183
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
1184
	select CPU_SUPPORTS_HIGHMEM
1185
	select CPU_SUPPORTS_HUGEPAGES
R
Ralf Baechle 已提交
1186 1187 1188 1189 1190 1191
	help
	  Choose this option to build a kernel for release 2 or later of the
	  MIPS64 architecture.  Many modern embedded systems with a 64-bit
	  MIPS processor are based on a MIPS64 processor.  If you know the
	  specific type of processor in your system, choose those that one
	  otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
L
Linus Torvalds 已提交
1192 1193 1194

config CPU_R3000
	bool "R3000"
1195
	depends on SYS_HAS_CPU_R3000
1196
	select CPU_HAS_WB
1197
	select CPU_SUPPORTS_32BIT_KERNEL
R
Ralf Baechle 已提交
1198
	select CPU_SUPPORTS_HIGHMEM
L
Linus Torvalds 已提交
1199 1200 1201 1202 1203 1204 1205 1206 1207 1208
	help
	  Please make sure to pick the right CPU type. Linux/MIPS is not
	  designed to be generic, i.e. Kernels compiled for R3000 CPUs will
	  *not* work on R4000 machines and vice versa.  However, since most
	  of the supported machines have an R4000 (or similar) CPU, R4x00
	  might be a safe bet.  If the resulting kernel does not work,
	  try to recompile with R3000.

config CPU_TX39XX
	bool "R39XX"
1209
	depends on SYS_HAS_CPU_TX39XX
1210
	select CPU_SUPPORTS_32BIT_KERNEL
L
Linus Torvalds 已提交
1211 1212 1213

config CPU_VR41XX
	bool "R41xx"
1214
	depends on SYS_HAS_CPU_VR41XX
1215 1216
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1217
	help
1218
	  The options selects support for the NEC VR4100 series of processors.
L
Linus Torvalds 已提交
1219 1220 1221 1222 1223 1224
	  Only choose this option if you have one of these processors as a
	  kernel built with this option will not run on any other type of
	  processor or vice versa.

config CPU_R4300
	bool "R4300"
1225
	depends on SYS_HAS_CPU_R4300
1226 1227
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1228 1229 1230 1231 1232
	help
	  MIPS Technologies R4300-series processors.

config CPU_R4X00
	bool "R4x00"
1233
	depends on SYS_HAS_CPU_R4X00
1234 1235
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1236 1237 1238 1239 1240 1241
	help
	  MIPS Technologies R4000-series processors other than 4300, including
	  the R4000, R4400, R4600, and 4700.

config CPU_TX49XX
	bool "R49XX"
1242
	depends on SYS_HAS_CPU_TX49XX
A
Atsushi Nemoto 已提交
1243
	select CPU_HAS_PREFETCH
1244 1245
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1246 1247 1248

config CPU_R5000
	bool "R5000"
1249
	depends on SYS_HAS_CPU_R5000
1250 1251
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1252 1253 1254 1255 1256
	help
	  MIPS Technologies R5000-series processors other than the Nevada.

config CPU_R5432
	bool "R5432"
1257
	depends on SYS_HAS_CPU_R5432
1258 1259
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1260

1261 1262 1263 1264 1265
config CPU_R5500
	bool "R5500"
	depends on SYS_HAS_CPU_R5500
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
1266
	select CPU_SUPPORTS_HUGEPAGES
1267 1268 1269 1270
	help
	  NEC VR5500 and VR5500A series processors implement 64-bit MIPS IV
	  instruction set.

L
Linus Torvalds 已提交
1271 1272
config CPU_R6000
	bool "R6000"
1273
	depends on EXPERIMENTAL
1274
	depends on SYS_HAS_CPU_R6000
1275
	select CPU_SUPPORTS_32BIT_KERNEL
L
Linus Torvalds 已提交
1276 1277
	help
	  MIPS Technologies R6000 and R6000A series processors.  Note these
C
Chris Dearman 已提交
1278
	  processors are extremely rare and the support for them is incomplete.
L
Linus Torvalds 已提交
1279 1280 1281

config CPU_NEVADA
	bool "RM52xx"
1282
	depends on SYS_HAS_CPU_NEVADA
1283 1284
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1285 1286 1287 1288 1289
	help
	  QED / PMC-Sierra RM52xx-series ("Nevada") processors.

config CPU_R8000
	bool "R8000"
1290
	depends on EXPERIMENTAL
1291
	depends on SYS_HAS_CPU_R8000
1292
	select CPU_HAS_PREFETCH
1293
	select CPU_SUPPORTS_64BIT_KERNEL
L
Linus Torvalds 已提交
1294 1295 1296 1297 1298 1299
	help
	  MIPS Technologies R8000 processors.  Note these processors are
	  uncommon and the support for them is incomplete.

config CPU_R10000
	bool "R10000"
1300
	depends on SYS_HAS_CPU_R10000
1301
	select CPU_HAS_PREFETCH
1302 1303
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
R
Ralf Baechle 已提交
1304
	select CPU_SUPPORTS_HIGHMEM
L
Linus Torvalds 已提交
1305 1306 1307 1308 1309
	help
	  MIPS Technologies R10000-series processors.

config CPU_RM7000
	bool "RM7000"
1310
	depends on SYS_HAS_CPU_RM7000
1311
	select CPU_HAS_PREFETCH
1312 1313
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
R
Ralf Baechle 已提交
1314
	select CPU_SUPPORTS_HIGHMEM
L
Linus Torvalds 已提交
1315 1316 1317

config CPU_RM9000
	bool "RM9000"
1318
	depends on SYS_HAS_CPU_RM9000
1319
	select CPU_HAS_PREFETCH
1320 1321
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
R
Ralf Baechle 已提交
1322
	select CPU_SUPPORTS_HIGHMEM
1323
	select WEAK_ORDERING
L
Linus Torvalds 已提交
1324 1325 1326

config CPU_SB1
	bool "SB1"
1327
	depends on SYS_HAS_CPU_SB1
1328 1329
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
R
Ralf Baechle 已提交
1330
	select CPU_SUPPORTS_HIGHMEM
1331
	select WEAK_ORDERING
L
Linus Torvalds 已提交
1332

1333 1334
config CPU_CAVIUM_OCTEON
	bool "Cavium Octeon processor"
1335
	depends on SYS_HAS_CPU_CAVIUM_OCTEON
1336 1337 1338 1339 1340 1341 1342 1343
	select IRQ_CPU
	select IRQ_CPU_OCTEON
	select CPU_HAS_PREFETCH
	select CPU_SUPPORTS_64BIT_KERNEL
	select SYS_SUPPORTS_SMP
	select NR_CPUS_DEFAULT_16
	select WEAK_ORDERING
	select CPU_SUPPORTS_HIGHMEM
1344
	select CPU_SUPPORTS_HUGEPAGES
1345 1346 1347 1348 1349 1350
	help
	  The Cavium Octeon processor is a highly integrated chip containing
	  many ethernet hardware widgets for networking tasks. The processor
	  can have up to 16 Mips64v2 cores and 8 integrated gigabit ethernets.
	  Full details can be found at http://www.caviumnetworks.com.

1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401
config CPU_BMIPS3300
	bool "BMIPS3300"
	depends on SYS_HAS_CPU_BMIPS3300
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_SUPPORTS_32BIT_KERNEL
	select WEAK_ORDERING
	help
	  Broadcom BMIPS3300 processors.

config CPU_BMIPS4350
	bool "BMIPS4350"
	depends on SYS_HAS_CPU_BMIPS4350
	select CPU_SUPPORTS_32BIT_KERNEL
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_SUPPORTS_SMP
	select SYS_SUPPORTS_HOTPLUG_CPU
	select WEAK_ORDERING
	help
	  Broadcom BMIPS4350 ("VIPER") processors.

config CPU_BMIPS4380
	bool "BMIPS4380"
	depends on SYS_HAS_CPU_BMIPS4380
	select CPU_SUPPORTS_32BIT_KERNEL
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_SUPPORTS_SMP
	select SYS_SUPPORTS_HOTPLUG_CPU
	select WEAK_ORDERING
	help
	  Broadcom BMIPS4380 processors.

config CPU_BMIPS5000
	bool "BMIPS5000"
	depends on SYS_HAS_CPU_BMIPS5000
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_HIGHMEM
	select DMA_NONCOHERENT
	select IRQ_CPU
	select SWAP_IO_SPACE
	select SYS_SUPPORTS_SMP
	select SYS_SUPPORTS_HOTPLUG_CPU
	select WEAK_ORDERING
	help
	  Broadcom BMIPS5000 processors.

L
Linus Torvalds 已提交
1402 1403
endchoice

1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430
if CPU_LOONGSON2F
config CPU_NOP_WORKAROUNDS
	bool

config CPU_JUMP_WORKAROUNDS
	bool

config CPU_LOONGSON2F_WORKAROUNDS
	bool "Loongson 2F Workarounds"
	default y
	select CPU_NOP_WORKAROUNDS
	select CPU_JUMP_WORKAROUNDS
	help
	  Loongson 2F01 / 2F02 processors have the NOP & JUMP issues which
	  require workarounds.  Without workarounds the system may hang
	  unexpectedly.  For more information please refer to the gas
	  -mfix-loongson2f-nop and -mfix-loongson2f-jump options.

	  Loongson 2F03 and later have fixed these issues and no workarounds
	  are needed.  The workarounds have no significant side effect on them
	  but may decrease the performance of the system so this option should
	  be disabled unless the kernel is intended to be run on 2F01 or 2F02
	  systems.

	  If unsure, please say Y.
endif # CPU_LOONGSON2F

1431 1432 1433 1434 1435
config SYS_SUPPORTS_ZBOOT
	bool
	select HAVE_KERNEL_GZIP
	select HAVE_KERNEL_BZIP2
	select HAVE_KERNEL_LZMA
1436
	select HAVE_KERNEL_LZO
1437 1438 1439 1440 1441

config SYS_SUPPORTS_ZBOOT_UART16550
	bool
	select SYS_SUPPORTS_ZBOOT

1442 1443 1444 1445 1446 1447 1448
config CPU_LOONGSON2
	bool
	select CPU_SUPPORTS_32BIT_KERNEL
	select CPU_SUPPORTS_64BIT_KERNEL
	select CPU_SUPPORTS_HIGHMEM

config SYS_HAS_CPU_LOONGSON2E
1449 1450
	bool

1451 1452
config SYS_HAS_CPU_LOONGSON2F
	bool
1453 1454
	select CPU_SUPPORTS_CPUFREQ
	select CPU_SUPPORTS_ADDRWINCFG if 64BIT
1455
	select CPU_SUPPORTS_UNCACHED_ACCELERATED
1456

1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492
config SYS_HAS_CPU_MIPS32_R1
	bool

config SYS_HAS_CPU_MIPS32_R2
	bool

config SYS_HAS_CPU_MIPS64_R1
	bool

config SYS_HAS_CPU_MIPS64_R2
	bool

config SYS_HAS_CPU_R3000
	bool

config SYS_HAS_CPU_TX39XX
	bool

config SYS_HAS_CPU_VR41XX
	bool

config SYS_HAS_CPU_R4300
	bool

config SYS_HAS_CPU_R4X00
	bool

config SYS_HAS_CPU_TX49XX
	bool

config SYS_HAS_CPU_R5000
	bool

config SYS_HAS_CPU_R5432
	bool

1493 1494 1495
config SYS_HAS_CPU_R5500
	bool

1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516
config SYS_HAS_CPU_R6000
	bool

config SYS_HAS_CPU_NEVADA
	bool

config SYS_HAS_CPU_R8000
	bool

config SYS_HAS_CPU_R10000
	bool

config SYS_HAS_CPU_RM7000
	bool

config SYS_HAS_CPU_RM9000
	bool

config SYS_HAS_CPU_SB1
	bool

1517 1518 1519
config SYS_HAS_CPU_CAVIUM_OCTEON
	bool

1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531
config SYS_HAS_CPU_BMIPS3300
	bool

config SYS_HAS_CPU_BMIPS4350
	bool

config SYS_HAS_CPU_BMIPS4380
	bool

config SYS_HAS_CPU_BMIPS5000
	bool

1532 1533 1534 1535
#
# CPU may reorder R->R, R->W, W->R, W->W
# Reordering beyond LL and SC is handled in WEAK_REORDERING_BEYOND_LLSC
#
1536 1537
config WEAK_ORDERING
	bool
1538 1539 1540 1541 1542 1543 1544

#
# CPU may reorder reads and writes beyond LL/SC
# CPU may reorder R->LL, R->LL, W->LL, W->LL, R->SC, R->SC, W->SC, W->SC
#
config WEAK_REORDERING_BEYOND_LLSC
	bool
1545 1546 1547
endmenu

#
C
Chris Dearman 已提交
1548
# These two indicate any level of the MIPS32 and MIPS64 architecture
1549 1550 1551 1552 1553 1554 1555 1556 1557 1558
#
config CPU_MIPS32
	bool
	default y if CPU_MIPS32_R1 || CPU_MIPS32_R2

config CPU_MIPS64
	bool
	default y if CPU_MIPS64_R1 || CPU_MIPS64_R2

#
C
Chris Dearman 已提交
1559
# These two indicate the revision of the architecture, either Release 1 or Release 2
1560 1561 1562 1563 1564 1565 1566
#
config CPU_MIPSR1
	bool
	default y if CPU_MIPS32_R1 || CPU_MIPS64_R1

config CPU_MIPSR2
	bool
1567
	default y if CPU_MIPS32_R2 || CPU_MIPS64_R2 || CPU_CAVIUM_OCTEON
1568 1569 1570 1571 1572 1573 1574 1575 1576

config SYS_SUPPORTS_32BIT_KERNEL
	bool
config SYS_SUPPORTS_64BIT_KERNEL
	bool
config CPU_SUPPORTS_32BIT_KERNEL
	bool
config CPU_SUPPORTS_64BIT_KERNEL
	bool
1577 1578 1579 1580
config CPU_SUPPORTS_CPUFREQ
	bool
config CPU_SUPPORTS_ADDRWINCFG
	bool
1581 1582
config CPU_SUPPORTS_HUGEPAGES
	bool
1583 1584
config CPU_SUPPORTS_UNCACHED_ACCELERATED
	bool
1585 1586 1587
config MIPS_PGD_C0_CONTEXT
	bool
	default y if 64BIT && CPU_MIPSR2
1588

1589 1590 1591 1592 1593
#
# Set to y for ptrace access to watch registers.
#
config HARDWARE_WATCHPOINTS
       bool
1594
       default y if CPU_MIPSR1 || CPU_MIPSR2
1595

1596 1597 1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615
menu "Kernel type"

choice

	prompt "Kernel code model"
	help
	  You should only select this option if you have a workload that
	  actually benefits from 64-bit processing or if your machine has
	  large memory.  You will only be presented a single option in this
	  menu if your system does not support both 32-bit and 64-bit kernels.

config 32BIT
	bool "32-bit kernel"
	depends on CPU_SUPPORTS_32BIT_KERNEL && SYS_SUPPORTS_32BIT_KERNEL
	select TRAD_SIGNALS
	help
	  Select this option if you want to build a 32-bit kernel.
config 64BIT
	bool "64-bit kernel"
	depends on CPU_SUPPORTS_64BIT_KERNEL && SYS_SUPPORTS_64BIT_KERNEL
1616
	select HAVE_SYSCALL_WRAPPERS
1617 1618 1619 1620 1621
	help
	  Select this option if you want to build a 64-bit kernel.

endchoice

L
Linus Torvalds 已提交
1622 1623 1624 1625 1626 1627
choice
	prompt "Kernel page size"
	default PAGE_SIZE_4KB

config PAGE_SIZE_4KB
	bool "4kB"
W
Wu Zhangjin 已提交
1628
	depends on !CPU_LOONGSON2
L
Linus Torvalds 已提交
1629 1630 1631 1632 1633 1634 1635 1636
	help
	 This option select the standard 4kB Linux page size.  On some
	 R3000-family processors this is the only available page size.  Using
	 4kB page size will minimize memory consumption and is therefore
	 recommended for low memory systems.

config PAGE_SIZE_8KB
	bool "8kB"
1637
	depends on (EXPERIMENTAL && CPU_R8000) || CPU_CAVIUM_OCTEON
L
Linus Torvalds 已提交
1638 1639 1640
	help
	  Using 8kB page size will result in higher performance kernel at
	  the price of higher memory consumption.  This option is available
1641 1642
	  only on R8000 and cnMIPS processors.  Note that you will need a
	  suitable Linux distribution to support this.
L
Linus Torvalds 已提交
1643 1644 1645

config PAGE_SIZE_16KB
	bool "16kB"
1646
	depends on !CPU_R3000 && !CPU_TX39XX
L
Linus Torvalds 已提交
1647 1648 1649
	help
	  Using 16kB page size will result in higher performance kernel at
	  the price of higher memory consumption.  This option is available on
1650 1651
	  all non-R3000 family processors.  Note that you will need a suitable
	  Linux distribution to support this.
L
Linus Torvalds 已提交
1652

1653 1654 1655 1656 1657 1658 1659 1660 1661
config PAGE_SIZE_32KB
	bool "32kB"
	depends on CPU_CAVIUM_OCTEON
	help
	  Using 32kB page size will result in higher performance kernel at
	  the price of higher memory consumption.  This option is available
	  only on cnMIPS cores.  Note that you will need a suitable Linux
	  distribution to support this.

L
Linus Torvalds 已提交
1662 1663 1664 1665 1666 1667 1668
config PAGE_SIZE_64KB
	bool "64kB"
	depends on EXPERIMENTAL && !CPU_R3000 && !CPU_TX39XX
	help
	  Using 64kB page size will result in higher performance kernel at
	  the price of higher memory consumption.  This option is available on
	  all non-R3000 family processor.  Not that at the time of this
1669
	  writing this option is still high experimental.
L
Linus Torvalds 已提交
1670 1671 1672

endchoice

1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694
config FORCE_MAX_ZONEORDER
	int "Maximum zone order"
	range 13 64 if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_32KB
	default "13" if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_32KB
	range 12 64 if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_16KB
	default "12" if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_16KB
	range 11 64
	default "11"
	help
	  The kernel memory allocator divides physically contiguous memory
	  blocks into "zones", where each zone is a power of two number of
	  pages.  This option selects the largest power of two that the kernel
	  keeps in the memory allocator.  If you need to allocate very large
	  blocks of physically contiguous memory, then you may need to
	  increase this value.

	  This config option is actually maximum order plus one. For example,
	  a value of 11 means that the largest free memory block is 2^10 pages.

	  The page size is not necessarily 4KB.  Keep this in mind
	  when choosing a value for this option.

L
Linus Torvalds 已提交
1695 1696 1697 1698 1699 1700 1701
config BOARD_SCACHE
	bool

config IP22_CPU_SCACHE
	bool
	select BOARD_SCACHE

1702 1703 1704 1705 1706 1707 1708
#
# Support for a MIPS32 / MIPS64 style S-caches
#
config MIPS_CPU_SCACHE
	bool
	select BOARD_SCACHE

L
Linus Torvalds 已提交
1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725
config R5000_CPU_SCACHE
	bool
	select BOARD_SCACHE

config RM7000_CPU_SCACHE
	bool
	select BOARD_SCACHE

config SIBYTE_DMA_PAGEOPS
	bool "Use DMA to clear/copy pages"
	depends on CPU_SB1
	help
	  Instead of using the CPU to zero and copy pages, use a Data Mover
	  channel.  These DMA channels are otherwise unused by the standard
	  SiByte Linux port.  Seems to give a small performance benefit.

config CPU_HAS_PREFETCH
1726
	bool
L
Linus Torvalds 已提交
1727

R
Ralf Baechle 已提交
1728 1729
choice
	prompt "MIPS MT options"
1730 1731 1732 1733 1734 1735 1736 1737

config MIPS_MT_DISABLED
	bool "Disable multithreading support."
	help
	  Use this option if your workload can't take advantage of
	  MIPS hardware multithreading support.  On systems that don't have
	  the option of an MT-enabled processor this option will be the only
	  option in this menu.
R
Ralf Baechle 已提交
1738

R
Ralf Baechle 已提交
1739 1740
config MIPS_MT_SMP
	bool "Use 1 TC on each available VPE for SMP"
1741
	depends on SYS_SUPPORTS_MULTITHREADING
1742
	select CPU_MIPSR2_IRQ_VI
1743
	select CPU_MIPSR2_IRQ_EI
1744
	select MIPS_MT
1745
	select NR_CPUS_DEFAULT_2
1746
	select SMP
1747
	select SYS_SUPPORTS_SCHED_SMT if SMP
1748
	select SYS_SUPPORTS_SMP
1749
	select SMP_UP
1750
	help
1751 1752 1753 1754 1755 1756 1757 1758 1759 1760
	  This is a kernel model which is known a VSMP but lately has been
	  marketesed into SMVP.
	  Virtual SMP uses the processor's VPEs  to implement virtual
	  processors. In currently available configuration of the 34K processor
	  this allows for a dual processor. Both processors will share the same
	  primary caches; each will obtain the half of the TLB for it's own
	  exclusive use. For a layman this model can be described as similar to
	  what Intel calls Hyperthreading.

	  For further information see http://www.linux-mips.org/wiki/34K#VSMP
1761

R
Ralf Baechle 已提交
1762 1763 1764 1765
config MIPS_MT_SMTC
	bool "SMTC: Use all TCs on all VPEs for SMP"
	depends on CPU_MIPS32_R2
	#depends on CPU_MIPS64_R2		# once there is hardware ...
1766 1767
	depends on SYS_SUPPORTS_MULTITHREADING
	select CPU_MIPSR2_IRQ_VI
1768
	select CPU_MIPSR2_IRQ_EI
1769
	select MIPS_MT
1770
	select NR_CPUS_DEFAULT_8
R
Ralf Baechle 已提交
1771
	select SMP
1772
	select SYS_SUPPORTS_SMP
1773
	select SMP_UP
1774
	help
R
Ralf Baechle 已提交
1775 1776
	  This is a kernel model which is known a SMTC or lately has been
	  marketesed into SMVP.
1777 1778 1779 1780 1781 1782 1783 1784
	  is presenting the available TC's of the core as processors to Linux.
	  On currently available 34K processors this means a Linux system will
	  see up to 5 processors. The implementation of the SMTC kernel differs
	  significantly from VSMP and cannot efficiently coexist in the same
	  kernel binary so the choice between VSMP and SMTC is a compile time
	  decision.

	  For further information see http://www.linux-mips.org/wiki/34K#SMTC
R
Ralf Baechle 已提交
1785 1786 1787

endchoice

1788 1789 1790
config MIPS_MT
	bool

1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803
config SCHED_SMT
	bool "SMT (multithreading) scheduler support"
	depends on SYS_SUPPORTS_SCHED_SMT
	default n
	help
	  SMT scheduler support improves the CPU scheduler's decision making
	  when dealing with MIPS MT enabled cores at a cost of slightly
	  increased overhead in some places. If unsure say N here.

config SYS_SUPPORTS_SCHED_SMT
	bool


1804 1805 1806
config SYS_SUPPORTS_MULTITHREADING
	bool

R
Ralf Baechle 已提交
1807 1808 1809
config MIPS_MT_FPAFF
	bool "Dynamic FPU affinity for FP-intensive threads"
	default y
1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820
	depends on MIPS_MT_SMP || MIPS_MT_SMTC

config MIPS_VPE_LOADER
	bool "VPE loader support."
	depends on SYS_SUPPORTS_MULTITHREADING
	select CPU_MIPSR2_IRQ_VI
	select CPU_MIPSR2_IRQ_EI
	select MIPS_MT
	help
	  Includes a loader for loading an elf relocatable object
	  onto another VPE and running it.
R
Ralf Baechle 已提交
1821

1822 1823 1824
config MIPS_MT_SMTC_IM_BACKSTOP
	bool "Use per-TC register bits as backstop for inhibited IM bits"
	depends on MIPS_MT_SMTC
1825
	default n
1826 1827 1828 1829 1830 1831
	help
	  To support multiple TC microthreads acting as "CPUs" within
	  a VPE, VPE-wide interrupt mask bits must be specially manipulated
	  during interrupt handling. To support legacy drivers and interrupt
	  controller management code, SMTC has a "backstop" to track and
	  if necessary restore the interrupt mask. This has some performance
1832
	  impact on interrupt service overhead.
1833

1834 1835 1836 1837 1838 1839 1840 1841
config MIPS_MT_SMTC_IRQAFF
	bool "Support IRQ affinity API"
	depends on MIPS_MT_SMTC
	default n
	help
	  Enables SMP IRQ affinity API (/proc/irq/*/smp_affinity, etc.)
	  for SMTC Linux kernel. Requires platform support, of which
	  an example can be found in the MIPS kernel i8259 and Malta
1842 1843
	  platform code.  Adds some overhead to interrupt dispatch, and
	  should be used only if you know what you are doing.
1844

1845 1846 1847 1848 1849 1850 1851 1852 1853 1854 1855 1856
config MIPS_VPE_LOADER_TOM
	bool "Load VPE program into memory hidden from linux"
	depends on MIPS_VPE_LOADER
	default y
	help
	  The loader can use memory that is present but has been hidden from
	  Linux using the kernel command line option "mem=xxMB". It's up to
	  you to ensure the amount you put in the option and the space your
	  program requires is less or equal to the amount physically present.

# this should possibly be in drivers/char, but it is rather cpu related. Hmmm
config MIPS_VPE_APSP_API
1857 1858 1859
	bool "Enable support for AP/SP API (RTLX)"
	depends on MIPS_VPE_LOADER
	help
1860

1861 1862 1863 1864 1865 1866 1867 1868 1869 1870
config MIPS_APSP_KSPD
	bool "Enable KSPD"
	depends on MIPS_VPE_APSP_API
	default y
	help
	  KSPD is a kernel daemon that accepts syscall requests from the SP
	  side, actions them and returns the results. It also handles the
	  "exit" syscall notifying other kernel modules the SP program is
	  exiting.  You probably want to say yes here.

1871 1872 1873
config MIPS_CMP
	bool "MIPS CMP framework support"
	depends on SYS_SUPPORTS_MIPS_CMP
1874
	select SYNC_R4K
1875 1876 1877 1878 1879 1880 1881 1882
	select SYS_SUPPORTS_SMP
	select SYS_SUPPORTS_SCHED_SMT if SMP
	select WEAK_ORDERING
	default n
	help
	  This is a placeholder option for the GCMP work. It will need to
	  be handled differently...

L
Linus Torvalds 已提交
1883 1884 1885 1886 1887 1888 1889 1890 1891 1892 1893 1894 1895 1896 1897 1898
config SB1_PASS_1_WORKAROUNDS
	bool
	depends on CPU_SB1_PASS_1
	default y

config SB1_PASS_2_WORKAROUNDS
	bool
	depends on CPU_SB1 && (CPU_SB1_PASS_2_2 || CPU_SB1_PASS_2)
	default y

config SB1_PASS_2_1_WORKAROUNDS
	bool
	depends on CPU_SB1 && CPU_SB1_PASS_2
	default y

config 64BIT_PHYS_ADDR
1899
	bool
L
Linus Torvalds 已提交
1900

1901 1902 1903
config ARCH_PHYS_ADDR_T_64BIT
       def_bool 64BIT_PHYS_ADDR

1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915
config CPU_HAS_SMARTMIPS
	depends on SYS_SUPPORTS_SMARTMIPS
	bool "Support for the SmartMIPS ASE"
	help
	  SmartMIPS is a extension of the MIPS32 architecture aimed at
	  increased security at both hardware and software level for
	  smartcards.  Enabling this option will allow proper use of the
	  SmartMIPS instructions by Linux applications.  However a kernel with
	  this option will not work on a MIPS core without SmartMIPS core.  If
	  you don't know you probably don't have SmartMIPS and should say N
	  here.

L
Linus Torvalds 已提交
1916
config CPU_HAS_WB
1917
	bool
1918

1919 1920 1921
#
# Vectored interrupt mode is an R2 feature
#
1922
config CPU_MIPSR2_IRQ_VI
1923
	bool
1924

1925 1926 1927
#
# Extended interrupt mode is an R2 feature
#
1928
config CPU_MIPSR2_IRQ_EI
1929
	bool
1930

L
Linus Torvalds 已提交
1931 1932 1933 1934 1935
config CPU_HAS_SYNC
	bool
	depends on !CPU_R3000
	default y

R
Ralf Baechle 已提交
1936 1937 1938
config GENERIC_CLOCKEVENTS_BROADCAST
	bool

1939 1940 1941 1942 1943 1944 1945 1946 1947 1948 1949 1950 1951
#
# CPU non-features
#
config CPU_DADDI_WORKAROUNDS
	bool

config CPU_R4000_WORKAROUNDS
	bool
	select CPU_R4400_WORKAROUNDS

config CPU_R4400_WORKAROUNDS
	bool

L
Linus Torvalds 已提交
1952 1953 1954 1955 1956 1957 1958 1959 1960
#
# - Highmem only makes sense for the 32-bit kernel.
# - The current highmem code will only work properly on physically indexed
#   caches such as R3000, SB1, R7000 or those that look like they're virtually
#   indexed such as R4000/R4400 SC and MC versions or R10000.  So for the
#   moment we protect the user and offer the highmem option only on machines
#   where it's known to be safe.  This will not offer highmem on a few systems
#   such as MIPS32 and MIPS64 CPUs which may have virtual and physically
#   indexed CPUs but we're playing safe.
R
Ralf Baechle 已提交
1961 1962 1963
# - We use SYS_SUPPORTS_HIGHMEM to offer highmem only for systems where we
#   know they might have memory configurations that could make use of highmem
#   support.
L
Linus Torvalds 已提交
1964 1965 1966
#
config HIGHMEM
	bool "High Memory Support"
R
Ralf Baechle 已提交
1967 1968 1969 1970 1971 1972 1973
	depends on 32BIT && CPU_SUPPORTS_HIGHMEM && SYS_SUPPORTS_HIGHMEM

config CPU_SUPPORTS_HIGHMEM
	bool

config SYS_SUPPORTS_HIGHMEM
	bool
L
Linus Torvalds 已提交
1974

1975 1976 1977
config SYS_SUPPORTS_SMARTMIPS
	bool

1978 1979
config ARCH_FLATMEM_ENABLE
	def_bool y
1980
	depends on !NUMA && !CPU_LOONGSON2
1981

1982 1983 1984 1985
config ARCH_DISCONTIGMEM_ENABLE
	bool
	default y if SGI_IP27
	help
1986
	  Say Y to support efficient handling of discontiguous physical memory,
1987 1988 1989 1990
	  for architectures which are either NUMA (Non-Uniform Memory Access)
	  or have huge holes in the physical address space for other reasons.
	  See <file:Documentation/vm/numa> for more.

1991 1992 1993
config ARCH_POPULATES_NODE_MAP
	def_bool y

1994 1995
config ARCH_SPARSEMEM_ENABLE
	bool
A
Atsushi Nemoto 已提交
1996
	select SPARSEMEM_STATIC
1997

1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010
config NUMA
	bool "NUMA Support"
	depends on SYS_SUPPORTS_NUMA
	help
	  Say Y to compile the kernel to support NUMA (Non-Uniform Memory
	  Access).  This option improves performance on systems with more
	  than two nodes; on two node systems it is generally better to
	  leave it disabled; on single node systems disable this option
	  disabled.

config SYS_SUPPORTS_NUMA
	bool

Y
Yasunori Goto 已提交
2011 2012 2013 2014 2015
config NODES_SHIFT
	int
	default "6"
	depends on NEED_MULTIPLE_NODES

2016 2017 2018 2019 2020 2021 2022 2023
config HW_PERF_EVENTS
	bool "Enable hardware performance counter support for perf events"
	depends on PERF_EVENTS && !MIPS_MT_SMTC && OPROFILE=n && CPU_MIPS32
	default y
	help
	  Enable hardware performance counter support for perf events. If
	  disabled, perf events will use software events only.

2024 2025
source "mm/Kconfig"

L
Linus Torvalds 已提交
2026 2027
config SMP
	bool "Multi-Processing support"
2028
	depends on SYS_SUPPORTS_SMP
2029
	select IRQ_PER_CPU
2030
	select USE_GENERIC_SMP_HELPERS
2031
	help
L
Linus Torvalds 已提交
2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 2044
	  This enables support for systems with more than one CPU. If you have
	  a system with only one CPU, like most personal computers, say N. If
	  you have a system with more than one CPU, say Y.

	  If you say N here, the kernel will run on single and multiprocessor
	  machines, but will use only one CPU of a multiprocessor machine. If
	  you say Y here, the kernel will run on many, but not all,
	  singleprocessor machines. On a singleprocessor machine, the kernel
	  will run faster if you say N here.

	  People using multiprocessor machines who say Y here should also say
	  Y to "Enhanced Real Time Clock Support", below.

A
Adrian Bunk 已提交
2045 2046
	  See also the SMP-HOWTO available at
	  <http://www.tldp.org/docs.html#howto>.
L
Linus Torvalds 已提交
2047 2048 2049

	  If you don't know what to do here, say N.

2050 2051 2052
config SMP_UP
	bool

2053 2054 2055
config SYS_SUPPORTS_MIPS_CMP
	bool

2056 2057 2058
config SYS_SUPPORTS_SMP
	bool

2059 2060 2061
config NR_CPUS_DEFAULT_1
	bool

2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079
config NR_CPUS_DEFAULT_2
	bool

config NR_CPUS_DEFAULT_4
	bool

config NR_CPUS_DEFAULT_8
	bool

config NR_CPUS_DEFAULT_16
	bool

config NR_CPUS_DEFAULT_32
	bool

config NR_CPUS_DEFAULT_64
	bool

L
Linus Torvalds 已提交
2080 2081
config NR_CPUS
	int "Maximum number of CPUs (2-64)"
2082
	range 1 64 if NR_CPUS_DEFAULT_1
L
Linus Torvalds 已提交
2083
	depends on SMP
2084
	default "1" if NR_CPUS_DEFAULT_1
2085 2086 2087 2088 2089 2090
	default "2" if NR_CPUS_DEFAULT_2
	default "4" if NR_CPUS_DEFAULT_4
	default "8" if NR_CPUS_DEFAULT_8
	default "16" if NR_CPUS_DEFAULT_16
	default "32" if NR_CPUS_DEFAULT_32
	default "64" if NR_CPUS_DEFAULT_64
L
Linus Torvalds 已提交
2091 2092 2093 2094
	help
	  This allows you to specify the maximum number of CPUs which this
	  kernel will support.  The maximum supported value is 32 for 32-bit
	  kernel and 64 for 64-bit kernels; the minimum value which makes
2095 2096
	  sense is 1 for Qemu (useful only for kernel debugging purposes)
	  and 2 for all others.
L
Linus Torvalds 已提交
2097 2098

	  This is purely to save memory - each supported CPU adds
2099 2100 2101
	  approximately eight kilobytes to the kernel image.  For best
	  performance should round up your number of processors to the next
	  power of two.
L
Linus Torvalds 已提交
2102

2103 2104
source "kernel/time/Kconfig"

2105 2106 2107 2108 2109 2110 2111 2112 2113 2114 2115
#
# Timer Interrupt Frequency Configuration
#

choice
	prompt "Timer frequency"
	default HZ_250
	help
	 Allows the configuration of the timer frequency.

	config HZ_48
2116
		bool "48 HZ" if SYS_SUPPORTS_48HZ || SYS_SUPPORTS_ARBIT_HZ
2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175

	config HZ_100
		bool "100 HZ" if SYS_SUPPORTS_100HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_128
		bool "128 HZ" if SYS_SUPPORTS_128HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_250
		bool "250 HZ" if SYS_SUPPORTS_250HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_256
		bool "256 HZ" if SYS_SUPPORTS_256HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_1000
		bool "1000 HZ" if SYS_SUPPORTS_1000HZ || SYS_SUPPORTS_ARBIT_HZ

	config HZ_1024
		bool "1024 HZ" if SYS_SUPPORTS_1024HZ || SYS_SUPPORTS_ARBIT_HZ

endchoice

config SYS_SUPPORTS_48HZ
	bool

config SYS_SUPPORTS_100HZ
	bool

config SYS_SUPPORTS_128HZ
	bool

config SYS_SUPPORTS_250HZ
	bool

config SYS_SUPPORTS_256HZ
	bool

config SYS_SUPPORTS_1000HZ
	bool

config SYS_SUPPORTS_1024HZ
	bool

config SYS_SUPPORTS_ARBIT_HZ
	bool
	default y if !SYS_SUPPORTS_48HZ && !SYS_SUPPORTS_100HZ && \
		     !SYS_SUPPORTS_128HZ && !SYS_SUPPORTS_250HZ && \
		     !SYS_SUPPORTS_256HZ && !SYS_SUPPORTS_1000HZ && \
		     !SYS_SUPPORTS_1024HZ

config HZ
	int
	default 48 if HZ_48
	default 100 if HZ_100
	default 128 if HZ_128
	default 250 if HZ_250
	default 256 if HZ_256
	default 1000 if HZ_1000
	default 1024 if HZ_1024

R
Ralf Baechle 已提交
2176
source "kernel/Kconfig.preempt"
L
Linus Torvalds 已提交
2177 2178 2179

config MIPS_INSANE_LARGE
	bool "Support for large 64-bit configurations"
2180
	depends on CPU_R10000 && 64BIT
L
Linus Torvalds 已提交
2181 2182 2183 2184 2185 2186 2187
	help
	  MIPS R10000 does support a 44 bit / 16TB address space as opposed to
	  previous 64-bit processors which only supported 40 bit / 1TB. If you
	  need processes of more than 1TB virtual address space, say Y here.
	  This will result in additional memory usage, so it is not
	  recommended for normal users.

2188 2189 2190 2191 2192 2193
config KEXEC
	bool "Kexec system call (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	help
	  kexec is a system call that implements the ability to shutdown your
	  current kernel, and to start another kernel.  It is like a reboot
2194
	  but it is independent of the system firmware.   And like a reboot
2195 2196
	  you can start any kernel with it, not just Linux.

M
Matt LaPlante 已提交
2197
	  The name comes from the similarity to the exec system call.
2198 2199 2200 2201 2202 2203 2204 2205 2206

	  It is an ongoing process to be certain the hardware in a machine
	  is properly shutdown, so do not be surprised if this code does not
	  initially work for you.  It may help to enable device hotplugging
	  support.  As of this writing the exact hardware interface is
	  strongly in flux, so no good recommendation can be made.

config SECCOMP
	bool "Enable seccomp to safely compute untrusted bytecode"
2207
	depends on PROC_FS
2208 2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221
	default y
	help
	  This kernel feature is useful for number crunching applications
	  that may need to compute untrusted bytecode during their
	  execution. By using pipes or other transports made available to
	  the process as file descriptors supporting the read/write
	  syscalls, it's possible to isolate those applications in
	  their own address space using seccomp. Once seccomp is
	  enabled via /proc/<pid>/seccomp, it cannot be disabled
	  and the task is only allowed to execute a few safe syscalls
	  defined by each seccomp mode.

	  If unsure, say Y. Only embedded should say N here.

2222 2223 2224
config USE_OF
	bool "Flattened Device Tree support"
	select OF
2225
	select OF_EARLY_FLATTREE
2226 2227 2228
	help
	  Include support for flattened device tree machine descriptions.

2229 2230
endmenu

2231 2232 2233 2234 2235 2236 2237 2238
config LOCKDEP_SUPPORT
	bool
	default y

config STACKTRACE_SUPPORT
	bool
	default y

2239 2240
source "init/Kconfig"

2241 2242
source "kernel/Kconfig.freezer"

L
Linus Torvalds 已提交
2243 2244
menu "Bus options (PCI, PCMCIA, EISA, ISA, TC)"

2245 2246
config HW_HAS_EISA
	bool
L
Linus Torvalds 已提交
2247 2248 2249 2250 2251 2252
config HW_HAS_PCI
	bool

config PCI
	bool "Support for PCI controller"
	depends on HW_HAS_PCI
2253
	select PCI_DOMAINS
L
Linus Torvalds 已提交
2254 2255 2256 2257 2258 2259 2260 2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273 2274
	help
	  Find out whether you have a PCI motherboard. PCI is the name of a
	  bus system, i.e. the way the CPU talks to the other stuff inside
	  your box. Other bus systems are ISA, EISA, or VESA. If you have PCI,
	  say Y, otherwise N.

config PCI_DOMAINS
	bool

source "drivers/pci/Kconfig"

#
# ISA support is now enabled via select.  Too many systems still have the one
# or other ISA chip on the board that users don't know about so don't expect
# users to choose the right thing ...
#
config ISA
	bool

config EISA
	bool "EISA support"
2275
	depends on HW_HAS_EISA
L
Linus Torvalds 已提交
2276
	select ISA
2277
	select GENERIC_ISA_DMA
L
Linus Torvalds 已提交
2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293 2294 2295 2296
	---help---
	  The Extended Industry Standard Architecture (EISA) bus was
	  developed as an open alternative to the IBM MicroChannel bus.

	  The EISA bus provided some of the features of the IBM MicroChannel
	  bus while maintaining backward compatibility with cards made for
	  the older ISA bus.  The EISA bus saw limited use between 1988 and
	  1995 when it was made obsolete by the PCI bus.

	  Say Y here if you are building a kernel for an EISA-based machine.

	  Otherwise, say N.

source "drivers/eisa/Kconfig"

config TC
	bool "TURBOchannel support"
	depends on MACH_DECSTATION
	help
2297 2298 2299 2300 2301 2302 2303 2304
	  TURBOchannel is a DEC (now Compaq (now HP)) bus for Alpha and MIPS
	  processors.  TURBOchannel programming specifications are available
	  at:
	  <ftp://ftp.hp.com/pub/alphaserver/archive/triadd/>
	  and:
	  <http://www.computer-refuge.org/classiccmp/ftp.digital.com/pub/DEC/TriAdd/>
	  Linux driver support status is documented at:
	  <http://www.linux-mips.org/wiki/DECstation>
L
Linus Torvalds 已提交
2305 2306 2307 2308 2309 2310 2311 2312 2313

#config ACCESSBUS
#	bool "Access.Bus support"
#	depends on TC

config MMU
	bool
	default y

2314 2315
config I8253
	bool
W
Wu Zhangjin 已提交
2316
	select MIPS_EXTERNAL_TIMER
2317

2318 2319 2320
config ZONE_DMA32
	bool

L
Linus Torvalds 已提交
2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335
source "drivers/pcmcia/Kconfig"

source "drivers/pci/hotplug/Kconfig"

endmenu

menu "Executable file formats"

source "fs/Kconfig.binfmt"

config TRAD_SIGNALS
	bool

config MIPS32_COMPAT
	bool "Kernel support for Linux/MIPS 32-bit binary compatibility"
2336
	depends on 64BIT
L
Linus Torvalds 已提交
2337 2338 2339 2340 2341 2342 2343 2344 2345 2346
	help
	  Select this option if you want Linux/MIPS 32-bit binary
	  compatibility. Since all software available for Linux/MIPS is
	  currently 32-bit you should say Y here.

config COMPAT
	bool
	depends on MIPS32_COMPAT
	default y

2347 2348 2349 2350 2351
config SYSVIPC_COMPAT
	bool
	depends on COMPAT && SYSVIPC
	default y

L
Linus Torvalds 已提交
2352 2353 2354 2355 2356 2357 2358 2359 2360 2361 2362 2363 2364 2365 2366 2367 2368 2369 2370 2371 2372 2373 2374 2375 2376
config MIPS32_O32
	bool "Kernel support for o32 binaries"
	depends on MIPS32_COMPAT
	help
	  Select this option if you want to run o32 binaries.  These are pure
	  32-bit binaries as used by the 32-bit Linux/MIPS port.  Most of
	  existing binaries are in this format.

	  If unsure, say Y.

config MIPS32_N32
	bool "Kernel support for n32 binaries"
	depends on MIPS32_COMPAT
	help
	  Select this option if you want to run n32 binaries.  These are
	  64-bit binaries using 32-bit quantities for addressing and certain
	  data that would normally be 64-bit.  They are used in special
	  cases.

	  If unsure, say N.

config BINFMT_ELF32
	bool
	default y if MIPS32_O32 || MIPS32_N32

2377 2378 2379 2380
endmenu

menu "Power management options"

W
Wu Zhangjin 已提交
2381 2382
config ARCH_HIBERNATION_POSSIBLE
	def_bool y
2383
	depends on SYS_SUPPORTS_HOTPLUG_CPU || !SMP
W
Wu Zhangjin 已提交
2384

J
Johannes Berg 已提交
2385 2386
config ARCH_SUSPEND_POSSIBLE
	def_bool y
2387
	depends on SYS_SUPPORTS_HOTPLUG_CPU || !SMP
J
Johannes Berg 已提交
2388

2389
source "kernel/power/Kconfig"
R
Rodolfo Giometti 已提交
2390

L
Linus Torvalds 已提交
2391 2392
endmenu

W
Wu Zhangjin 已提交
2393 2394
source "arch/mips/kernel/cpufreq/Kconfig"

2395 2396
source "net/Kconfig"

L
Linus Torvalds 已提交
2397 2398 2399 2400 2401 2402 2403 2404 2405 2406 2407
source "drivers/Kconfig"

source "fs/Kconfig"

source "arch/mips/Kconfig.debug"

source "security/Kconfig"

source "crypto/Kconfig"

source "lib/Kconfig"