Kconfig 30.6 KB
Newer Older
1
# SPDX-License-Identifier: GPL-2.0-only
2 3 4
#
# SPI driver configuration
#
5
menuconfig SPI
6
	bool "SPI support"
7
	depends on HAS_IOMEM
8 9 10 11 12 13 14
	help
	  The "Serial Peripheral Interface" is a low level synchronous
	  protocol.  Chips that support SPI can have data transfer rates
	  up to several tens of Mbit/sec.  Chips are addressed with a
	  controller and a chipselect.  Most SPI slaves don't support
	  dynamic device discovery; some are even write-only or read-only.

M
Matt LaPlante 已提交
15
	  SPI is widely used by microcontrollers to talk with sensors,
16 17 18 19 20 21 22 23 24 25
	  eeprom and flash memory, codecs and various other controller
	  chips, analog to digital (and d-to-a) converters, and more.
	  MMC and SD cards can be accessed using SPI protocol; and for
	  DataFlash cards used in MMC sockets, SPI must always be used.

	  SPI is one of a family of similar protocols using a four wire
	  interface (select, clock, data in, data out) including Microwire
	  (half duplex), SSP, SSI, and PSP.  This driver framework should
	  work with most such devices and controllers.

26 27
if SPI

28
config SPI_DEBUG
29
	bool "Debug support for SPI drivers"
30
	depends on DEBUG_KERNEL
31 32 33 34 35 36 37 38 39
	help
	  Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
	  sysfs, and debugfs support in SPI controller and protocol drivers.

#
# MASTER side ... talking to discrete SPI slave chips including microcontrollers
#

config SPI_MASTER
40 41
#	bool "SPI Master Support"
	bool
42 43 44 45 46 47 48
	default SPI
	help
	  If your system has an master-capable SPI controller (which
	  provides the clock and chipselect), you can enable that
	  controller and the protocol drivers for the SPI slave chips
	  that are connected.

R
Robert P. J. Day 已提交
49 50
if SPI_MASTER

51 52 53 54 55
config SPI_MEM
	bool "SPI memory extension"
	help
	  Enable this option if you want to enable the SPI memory extension.
	  This extension is meant to simplify interaction with SPI memories
56
	  by providing a high-level interface to send memory-like commands.
57

58 59
comment "SPI Master Controller Drivers"

T
Thomas Chou 已提交
60 61 62 63 64
config SPI_ALTERA
	tristate "Altera SPI Controller"
	help
	  This is the driver for the Altera SPI Controller.

65 66 67 68 69 70 71
config SPI_AR934X
	tristate "Qualcomm Atheros AR934X/QCA95XX SPI controller driver"
	depends on ATH79 || COMPILE_TEST
	help
	  This enables support for the SPI controller present on the
	  Qualcomm Atheros AR934X/QCA95XX SoCs.

72 73
config SPI_ATH79
	tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
74
	depends on ATH79 || COMPILE_TEST
75 76 77 78 79
	select SPI_BITBANG
	help
	  This enables support for the SPI controller present on the
	  Atheros AR71XX/AR724X/AR913X SoCs.

80 81 82 83 84 85 86
config SPI_ARMADA_3700
	tristate "Marvell Armada 3700 SPI Controller"
	depends on (ARCH_MVEBU && OF) || COMPILE_TEST
	help
	  This enables support for the SPI controller present on the
	  Marvell Armada 3700 SoCs.

87 88
config SPI_ATMEL
	tristate "Atmel SPI Controller"
89
	depends on ARCH_AT91 || COMPILE_TEST
90
	depends on OF
91 92
	help
	  This selects a driver for the Atmel SPI Controller, present on
93
	  many AT91 ARM chips.
94

95 96 97 98 99 100 101 102
config SPI_AT91_USART
	tristate "Atmel USART Controller SPI driver"
	depends on (ARCH_AT91 || COMPILE_TEST)
	depends on MFD_AT91_USART
	help
	  This selects a driver for the AT91 USART Controller as SPI Master,
	  present on AT91 and SAMA5 SoC series.

103 104
config SPI_ATMEL_QUADSPI
	tristate "Atmel Quad SPI Controller"
105
	depends on ARCH_AT91 || (ARM && COMPILE_TEST && !ARCH_EBSA110)
106 107 108 109 110 111
	depends on OF && HAS_IOMEM
	help
	  This enables support for the Quad SPI controller in master mode.
	  This driver does not support generic SPI. The implementation only
	  supports spi-mem interface.

M
Mark Brown 已提交
112 113 114 115 116 117 118 119
config SPI_AU1550
	tristate "Au1550/Au1200/Au1300 SPI Controller"
	depends on MIPS_ALCHEMY
	select SPI_BITBANG
	help
	  If you say yes to this option, support will be included for the
	  PSC SPI controller found on Au1550, Au1200 and Au1300 series.

120 121 122 123 124 125 126 127
config SPI_AXI_SPI_ENGINE
	tristate "Analog Devices AXI SPI Engine controller"
	depends on HAS_IOMEM
	help
	  This enables support for the Analog Devices AXI SPI Engine SPI controller.
	  It is part of the SPI Engine framework that is used in some Analog Devices
	  reference designs for FPGAs.

C
Chris Boot 已提交
128 129
config SPI_BCM2835
	tristate "BCM2835 SPI controller"
Y
Yoshinori Sato 已提交
130
	depends on GPIOLIB
131
	depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST
C
Chris Boot 已提交
132 133 134 135 136 137 138 139
	help
	  This selects a driver for the Broadcom BCM2835 SPI master.

	  The BCM2835 contains two types of SPI master controller; the
	  "universal SPI master", and the regular SPI controller. This driver
	  is for the regular SPI controller. Slave mode operation is not also
	  not supported.

140 141
config SPI_BCM2835AUX
	tristate "BCM2835 SPI auxiliary controller"
142
	depends on ((ARCH_BCM2835 || ARCH_BRCMSTB) && GPIOLIB) || COMPILE_TEST
143 144 145 146 147 148 149
	help
	  This selects a driver for the Broadcom BCM2835 SPI aux master.

	  The BCM2835 contains two types of SPI master controller; the
	  "universal SPI master", and the regular SPI controller.
	  This driver is for the universal/auxiliary SPI controller.

150 151
config SPI_BCM63XX
	tristate "Broadcom BCM63xx SPI controller"
152
	depends on BCM63XX || BMIPS_GENERIC || COMPILE_TEST
153
	help
K
Krzysztof Kozlowski 已提交
154
	  Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
155

156 157
config SPI_BCM63XX_HSSPI
	tristate "Broadcom BCM63XX HS SPI controller driver"
158
	depends on BCM63XX || BMIPS_GENERIC || ARCH_BCM_63XX || COMPILE_TEST
159 160 161 162
	help
	  This enables support for the High Speed SPI controller present on
	  newer Broadcom BCM63XX SoCs.

163 164
config SPI_BCM_QSPI
	tristate "Broadcom BSPI and MSPI controller support"
165 166
	depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
			BMIPS_GENERIC || COMPILE_TEST
167 168 169 170 171 172 173
	default ARCH_BCM_IPROC
	help
	  Enables support for the Broadcom SPI flash and MSPI controller.
	  Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
	  based platforms. This driver works for both SPI master for spi-nor
	  flash device as well as MSPI device.

174
config SPI_BITBANG
D
David Brownell 已提交
175
	tristate "Utilities for Bitbanging SPI masters"
176 177 178 179 180 181 182 183 184 185
	help
	  With a few GPIO pins, your system can bitbang the SPI protocol.
	  Select this to get SPI support through I/O pins (GPIO, parallel
	  port, etc).  Or, some systems' SPI master controller drivers use
	  this code to manage the per-word or per-transfer accesses to the
	  hardware shift registers.

	  This is library code, and is automatically selected by drivers that
	  need it.  You only need to select this explicitly to support driver
	  modules that aren't part of this kernel tree.
186

D
David Brownell 已提交
187 188
config SPI_BUTTERFLY
	tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
R
Robert P. J. Day 已提交
189
	depends on PARPORT
D
David Brownell 已提交
190 191 192 193 194 195 196
	select SPI_BITBANG
	help
	  This uses a custom parallel port cable to connect to an AVR
	  Butterfly <http://www.atmel.com/products/avr/butterfly>, an
	  inexpensive battery powered microcontroller evaluation board.
	  This same cable can be used to flash new firmware.

197 198 199 200
config SPI_CADENCE
	tristate "Cadence SPI controller"
	help
	  This selects the Cadence SPI controller master driver
201
	  used by Xilinx Zynq and ZynqMP.
202

203 204
config SPI_CLPS711X
	tristate "CLPS711X host SPI controller"
205
	depends on ARCH_CLPS711X || COMPILE_TEST
206 207 208 209
	help
	  This enables dedicated general purpose SPI/Microwire1-compatible
	  master mode interface (SSI1) for CLPS711X-based CPUs.

210 211
config SPI_COLDFIRE_QSPI
	tristate "Freescale Coldfire QSPI controller"
212
	depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
213 214 215 216
	help
	  This enables support for the Coldfire QSPI controller in master
	  mode.

217
config SPI_DAVINCI
218
	tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
219
	depends on ARCH_DAVINCI || ARCH_KEYSTONE
220 221
	select SPI_BITBANG
	help
222 223
	  SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.

M
Mark Brown 已提交
224 225 226 227 228
config SPI_DESIGNWARE
	tristate "DesignWare SPI controller core support"
	help
	  general driver for SPI controller core from DesignWare

229 230
if SPI_DESIGNWARE

231 232 233
config SPI_DW_DMA
	bool "DMA support for DW SPI controller"

M
Mark Brown 已提交
234 235
config SPI_DW_PCI
	tristate "PCI interface driver for DW SPI core"
236
	depends on PCI
M
Mark Brown 已提交
237 238 239

config SPI_DW_MMIO
	tristate "Memory-mapped io interface driver for DW SPI core"
240 241 242
	depends on HAS_IOMEM

endif
M
Mark Brown 已提交
243

244 245 246 247
config SPI_DLN2
       tristate "Diolan DLN-2 USB SPI adapter"
       depends on MFD_DLN2
       help
K
Krzysztof Kozlowski 已提交
248 249
	 If you say yes to this option, support will be included for Diolan
	 DLN2, a USB to SPI interface.
250

K
Krzysztof Kozlowski 已提交
251 252
	 This driver can also be built as a module.  If so, the module
	 will be called spi-dln2.
253

254 255 256 257 258 259 260
config SPI_EFM32
	tristate "EFM32 SPI controller"
	depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
	select SPI_BITBANG
	help
	  Driver for the spi controller found on Energy Micro's EFM32 SoCs.

261 262
config SPI_EP93XX
	tristate "Cirrus Logic EP93xx SPI controller"
263
	depends on ARCH_EP93XX || COMPILE_TEST
264 265 266 267
	help
	  This enables using the Cirrus EP93xx SPI controller in master
	  mode.

268
config SPI_FALCON
H
Hauke Mehrtens 已提交
269
	bool "Falcon SPI controller support"
270 271 272 273 274 275 276
	depends on SOC_FALCON
	help
	  The external bus unit (EBU) found on the FALC-ON SoC has SPI
	  emulation that is designed for serial flash access. This driver
	  has only been tested with m25p80 type chips. The hardware has no
	  support for other types of SPI peripherals.

277 278 279 280 281 282 283
config SPI_FSI
	tristate "FSI SPI driver"
	depends on FSI
	help
	  This enables support for the driver for FSI bus attached SPI
	  controllers.

G
Gao Pan 已提交
284 285 286 287 288 289
config SPI_FSL_LPSPI
	tristate "Freescale i.MX LPSPI controller"
	depends on ARCH_MXC || COMPILE_TEST
	help
	  This enables Freescale i.MX LPSPI controllers in master mode.

290 291 292 293 294 295 296 297 298 299 300
config SPI_FSL_QUADSPI
	tristate "Freescale QSPI controller"
	depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
	depends on HAS_IOMEM
	help
	  This enables support for the Quad SPI controller in master mode.
	  Up to four flash chips can be connected on two buses with two
	  chipselects each.
	  This controller does not support generic SPI messages. It only
	  supports the high-level SPI memory interface.

301 302 303 304 305 306 307 308
config SPI_HISI_SFC_V3XX
	tristate "HiSilicon SPI-NOR Flash Controller for Hi16XX chipsets"
	depends on (ARM64 && ACPI) || COMPILE_TEST
	depends on HAS_IOMEM
	help
	  This enables support for HiSilicon v3xx SPI-NOR flash controller
	  found in hi16xx chipsets.

309 310 311 312 313 314 315 316 317 318
config SPI_NXP_FLEXSPI
	tristate "NXP Flex SPI controller"
	depends on ARCH_LAYERSCAPE || HAS_IOMEM
	help
	  This enables support for the Flex SPI controller in master mode.
	  Up to four slave devices can be connected on two buses with two
	  chipselects each.
	  This controller does not support generic SPI messages and only
	  supports the high-level SPI memory interface.

D
David Brownell 已提交
319 320
config SPI_GPIO
	tristate "GPIO-based bitbanging SPI Master"
321
	depends on GPIOLIB || COMPILE_TEST
D
David Brownell 已提交
322 323 324 325 326 327 328 329 330 331 332 333 334
	select SPI_BITBANG
	help
	  This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
	  interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
	  slaves connected to a bus using this driver are configured as usual,
	  except that the spi_board_info.controller_data holds the GPIO number
	  for the chipselect used by this controller driver.

	  Note that this driver often won't achieve even 1 Mbit/sec speeds,
	  making it unusually slow for SPI.  If your platform can inline
	  GPIO operations, you should be able to leverage that for better
	  speed with a custom version of this driver; see the source code.

335 336 337 338 339 340 341
config SPI_IMG_SPFI
	tristate "IMG SPFI controller"
	depends on MIPS || COMPILE_TEST
	help
	  This enables support for the SPFI master controller found on
	  IMG SoCs.

342 343
config SPI_IMX
	tristate "Freescale i.MX SPI controllers"
344
	depends on ARCH_MXC || COMPILE_TEST
345 346
	select SPI_BITBANG
	help
347
	  This enables support for the Freescale i.MX SPI controllers.
348

349 350 351 352 353 354 355
config SPI_JCORE
	tristate "J-Core SPI Master"
	depends on OF && (SUPERH || COMPILE_TEST)
	help
	  This enables support for the SPI master controller in the J-Core
	  synthesizable, open source SoC.

356 357
config SPI_LM70_LLP
	tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
358
	depends on PARPORT
359 360 361 362 363 364
	select SPI_BITBANG
	help
	  This driver supports the NS LM70 LLP Evaluation Board,
	  which interfaces to an LM70 temperature sensor using
	  a parallel port.

365 366 367 368 369 370 371 372 373 374
config SPI_LP8841_RTC
	tristate "ICP DAS LP-8841 SPI Controller for RTC"
	depends on MACH_PXA27X_DT || COMPILE_TEST
	help
	  This driver provides an SPI master device to drive Maxim
	  DS-1302 real time clock.

	  Say N here unless you plan to run the kernel on an ICP DAS
	  LP-8x4x industrial computer.

375 376
config SPI_MPC52xx
	tristate "Freescale MPC52xx SPI (non-PSC) controller support"
P
Paul Bolle 已提交
377
	depends on PPC_MPC52xx
378 379 380 381
	help
	  This drivers supports the MPC52xx SPI controller in master SPI
	  mode.

D
Dragos Carp 已提交
382 383
config SPI_MPC52xx_PSC
	tristate "Freescale MPC52xx PSC SPI controller"
384
	depends on PPC_MPC52xx
D
Dragos Carp 已提交
385 386 387 388
	help
	  This enables using the Freescale MPC52xx Programmable Serial
	  Controller in master SPI mode.

389 390
config SPI_MPC512x_PSC
	tristate "Freescale MPC512x PSC SPI controller"
391
	depends on PPC_MPC512x
392 393 394 395
	help
	  This enables using the Freescale MPC5121 Programmable Serial
	  Controller in SPI master mode.

396
config SPI_FSL_LIB
397 398 399 400
	tristate
	depends on OF

config SPI_FSL_CPM
401 402 403
	tristate
	depends on FSL_SOC

404
config SPI_FSL_SPI
405
	tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
406
	depends on OF
407
	select SPI_FSL_LIB
408
	select SPI_FSL_CPM if FSL_SOC
409
	help
410 411 412
	  This enables using the Freescale SPI controllers in master mode.
	  MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
	  MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
413 414
	  This also enables using the Aeroflex Gaisler GRLIB SPI controller in
	  master mode.
415

416 417
config SPI_FSL_DSPI
	tristate "Freescale DSPI controller"
418
	select REGMAP_MMIO
419
	depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
420 421
	help
	  This enables support for the Freescale DSPI controller in master
422
	  mode. VF610, LS1021A and ColdFire platforms uses the controller.
423

424
config SPI_FSL_ESPI
425
	tristate "Freescale eSPI controller"
426 427 428 429 430 431
	depends on FSL_SOC
	help
	  This enables using the Freescale eSPI controllers in master mode.
	  From MPC8536, 85xx platform uses the controller, and all P10xx,
	  P20xx, P30xx,P40xx, P50xx uses this controller.

N
Neil Armstrong 已提交
432 433
config SPI_MESON_SPICC
	tristate "Amlogic Meson SPICC controller"
434
	depends on COMMON_CLK
N
Neil Armstrong 已提交
435 436 437 438 439
	depends on ARCH_MESON || COMPILE_TEST
	help
	  This enables master mode support for the SPICC (SPI communication
	  controller) available in Amlogic Meson SoCs.

440 441 442
config SPI_MESON_SPIFC
	tristate "Amlogic Meson SPIFC controller"
	depends on ARCH_MESON || COMPILE_TEST
B
Beniamino Galvani 已提交
443
	select REGMAP_MMIO
444 445 446 447
	help
	  This enables master mode support for the SPIFC (SPI flash
	  controller) available in Amlogic Meson SoCs.

448 449 450 451 452 453 454 455 456
config SPI_MT65XX
	tristate "MediaTek SPI controller"
	depends on ARCH_MEDIATEK || COMPILE_TEST
	help
	  This selects the MediaTek(R) SPI bus driver.
	  If you want to use MediaTek(R) SPI interface,
	  say Y or M here.If you are not sure, say N.
	  SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.

457 458 459 460 461 462
config SPI_MT7621
	tristate "MediaTek MT7621 SPI Controller"
	depends on RALINK || COMPILE_TEST
	help
	  This selects a driver for the MediaTek MT7621 SPI Controller.

463 464 465 466 467 468 469 470 471 472
config SPI_MTK_NOR
	tristate "MediaTek SPI NOR controller"
	depends on ARCH_MEDIATEK || COMPILE_TEST
	help
	  This enables support for SPI NOR controller found on MediaTek
	  ARM SoCs. This is a controller specifically for SPI-NOR flash.
	  It can perform generic SPI transfers up to 6 bytes via generic
	  SPI interface as well as several SPI-NOR specific instructions
	  via SPI MEM interface.

473 474 475 476 477 478 479 480 481 482
config SPI_NPCM_FIU
	tristate "Nuvoton NPCM FLASH Interface Unit"
	depends on ARCH_NPCM || COMPILE_TEST
	depends on OF && HAS_IOMEM
	help
	  This enables support for the Flash Interface Unit SPI controller
	  in master mode.
	  This driver does not support generic SPI. The implementation only
	  supports spi-mem interface.

483 484 485 486 487 488 489
config SPI_NPCM_PSPI
	tristate "Nuvoton NPCM PSPI Controller"
	depends on ARCH_NPCM || COMPILE_TEST
	help
	  This driver provides support for Nuvoton NPCM BMC
	  Peripheral SPI controller in master mode.

490 491
config SPI_LANTIQ_SSC
	tristate "Lantiq SSC SPI controller"
492
	depends on LANTIQ || COMPILE_TEST
493 494 495 496 497
	help
	  This driver supports the Lantiq SSC SPI controller in master
	  mode. This controller is found on Intel (former Lantiq) SoCs like
	  the Danube, Falcon, xRX200, xRX300.

T
Thomas Chou 已提交
498 499
config SPI_OC_TINY
	tristate "OpenCores tiny SPI"
500
	depends on GPIOLIB || COMPILE_TEST
T
Thomas Chou 已提交
501 502 503 504
	select SPI_BITBANG
	help
	  This is the driver for OpenCores tiny SPI master controller.

505 506
config SPI_OCTEON
	tristate "Cavium OCTEON SPI controller"
507
	depends on CAVIUM_OCTEON_SOC
508 509 510 511
	help
	  SPI host driver for the hardware found on some Cavium OCTEON
	  SOCs.

512 513
config SPI_OMAP_UWIRE
	tristate "OMAP1 MicroWire"
R
Robert P. J. Day 已提交
514
	depends on ARCH_OMAP1
515 516 517 518
	select SPI_BITBANG
	help
	  This hooks up to the MicroWire controller on OMAP1 chips.

S
Samuel Ortiz 已提交
519
config SPI_OMAP24XX
S
Syed Rafiuddin 已提交
520
	tristate "McSPI driver for OMAP"
521
	depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
522
	select SG_SPLIT
S
Samuel Ortiz 已提交
523
	help
S
Syed Rafiuddin 已提交
524
	  SPI master controller for OMAP24XX and later Multichannel SPI
S
Samuel Ortiz 已提交
525
	  (McSPI) modules.
526

527 528 529 530 531 532 533 534
config SPI_TI_QSPI
	tristate "DRA7xxx QSPI controller support"
	depends on ARCH_OMAP2PLUS || COMPILE_TEST
	help
	  QSPI master controller for DRA7xxx used for flash devices.
	  This device supports single, dual and quad read support, while
	  it only supports single write mode.

C
Cory Maccarrone 已提交
535 536
config SPI_OMAP_100K
	tristate "OMAP SPI 100K"
537
	depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
C
Cory Maccarrone 已提交
538 539 540
	help
	  OMAP SPI 100K master controller for omap7xx boards.

S
Shadi Ammouri 已提交
541
config SPI_ORION
542
	tristate "Orion SPI master"
543
	depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
S
Shadi Ammouri 已提交
544
	help
545 546
	  This enables using the SPI master controller on the Orion
	  and MVEBU chips.
S
Shadi Ammouri 已提交
547

548 549 550 551 552 553
config SPI_PIC32
	tristate "Microchip PIC32 series SPI"
	depends on MACH_PIC32 || COMPILE_TEST
	help
	  SPI driver for Microchip PIC32 SPI master controller.

554 555 556 557 558 559
config SPI_PIC32_SQI
	tristate "Microchip PIC32 Quad SPI driver"
	depends on MACH_PIC32 || COMPILE_TEST
	help
	  SPI driver for PIC32 Quad SPI controller.

560
config SPI_PL022
561 562
	tristate "ARM AMBA PL022 SSP controller"
	depends on ARM_AMBA
563
	default y if MACH_U300
564 565 566
	default y if ARCH_REALVIEW
	default y if INTEGRATOR_IMPD1
	default y if ARCH_VERSATILE
567 568 569 570 571
	help
	  This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
	  controller. If you have an embedded system with an AMBA(R)
	  bus and a PL022 controller, say Y or M here.

S
Steven A. Falco 已提交
572 573
config SPI_PPC4xx
	tristate "PPC4xx SPI Controller"
574
	depends on PPC32 && 4xx
S
Steven A. Falco 已提交
575 576 577 578
	select SPI_BITBANG
	help
	  This selects a driver for the PPC4xx SPI Controller.

579 580
config SPI_PXA2XX
	tristate "PXA2xx SSP SPI master"
581
	depends on ARCH_PXA || ARCH_MMP || PCI || ACPI || COMPILE_TEST
A
Arnd Bergmann 已提交
582
	select PXA_SSP if ARCH_PXA || ARCH_MMP
583
	help
584 585
	  This enables using a PXA2xx or Sodaville SSP port as a SPI master
	  controller. The driver can be configured to use any SSP port and
586
	  additional documentation can be found a Documentation/spi/pxa2xx.rst.
587 588

config SPI_PXA2XX_PCI
589
	def_tristate SPI_PXA2XX && PCI && COMMON_CLK
590

591 592 593 594 595 596 597 598 599 600 601
config SPI_ROCKCHIP
	tristate "Rockchip SPI controller driver"
	help
	  This selects a driver for Rockchip SPI controller.

	  If you say yes to this option, support will be included for
	  RK3066, RK3188 and RK3288 families of SPI controller.
	  Rockchip SPI controller support DMA transport and PIO mode.
	  The main usecase of this controller is to use spi flash as boot
	  device.

602 603 604 605 606 607
config SPI_RB4XX
	tristate "Mikrotik RB4XX SPI master"
	depends on SPI_MASTER && ATH79
	help
	  SPI controller driver for the Mikrotik RB4xx series boards.

S
Sergei Shtylyov 已提交
608 609 610 611 612 613
config SPI_RPCIF
	tristate "Renesas RPC-IF SPI driver"
	depends on RENESAS_RPCIF
	help
	  SPI driver for Renesas R-Car Gen3 RPC-IF.

614
config SPI_RSPI
615
	tristate "Renesas RSPI/QSPI controller"
616
	depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
617
	help
618
	  SPI driver for Renesas RSPI and QSPI blocks.
619

620 621 622 623 624 625
config SPI_QCOM_QSPI
	tristate "QTI QSPI controller"
	depends on ARCH_QCOM
	help
	  QSPI(Quad SPI) driver for Qualcomm QSPI controller.

626 627
config SPI_QUP
	tristate "Qualcomm SPI controller with QUP interface"
P
Paul Bolle 已提交
628
	depends on ARCH_QCOM || (ARM && COMPILE_TEST)
629 630 631 632 633 634 635 636 637
	help
	  Qualcomm Universal Peripheral (QUP) core is an AHB slave that
	  provides a common data path (an output FIFO and an input FIFO)
	  for serial peripheral interface (SPI) mini-core. SPI in master
	  mode supports up to 50MHz, up to four chip selects, programmable
	  data path from 4 bits to 32 bits and numerous protocol variants.

	  This driver can also be built as a module.  If so, the module
	  will be called spi_qup.
638

639 640 641 642 643 644 645 646 647 648 649 650
config SPI_QCOM_GENI
	tristate "Qualcomm GENI based SPI controller"
	depends on QCOM_GENI_SE
	help
	  This driver supports GENI serial engine based SPI controller in
	  master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
	  yes to this option, support will be included for the built-in SPI
	  interface on the Qualcomm Technologies Inc.'s SoCs.

	  This driver can also be built as a module.  If so, the module
	  will be called spi-geni-qcom.

D
David Brownell 已提交
651 652
config SPI_S3C24XX
	tristate "Samsung S3C24XX series SPI"
653
	depends on ARCH_S3C24XX
654
	select SPI_BITBANG
D
David Brownell 已提交
655 656 657
	help
	  SPI driver for Samsung S3C24XX series ARM SoCs

658 659 660 661 662 663 664 665 666 667 668
config SPI_S3C24XX_FIQ
	bool "S3C24XX driver with FIQ pseudo-DMA"
	depends on SPI_S3C24XX
	select FIQ
	help
	  Enable FIQ support for the S3C24XX SPI driver to provide pseudo
	  DMA by using the fast-interrupt request framework, This allows
	  the driver to get DMA-like performance when there are either
	  no free DMA channels, or when doing transfers that required both
	  TX and RX data paths.

669 670
config SPI_S3C64XX
	tristate "Samsung S3C64XX series type SPI"
671
	depends on (PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST)
672 673 674
	help
	  SPI driver for Samsung S3C64XX and newer SoCs.

675 676 677 678 679 680
config SPI_SC18IS602
	tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
	depends on I2C
	help
	  SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.

681 682
config SPI_SH_MSIOF
	tristate "SuperH MSIOF SPI controller"
683
	depends on HAVE_CLK
684
	depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
685
	help
686
	  SPI driver for SuperH and SH Mobile MSIOF blocks.
687

688 689
config SPI_SH
	tristate "SuperH SPI controller"
690
	depends on SUPERH || COMPILE_TEST
691 692 693
	help
	  SPI driver for SuperH SPI blocks.

M
Magnus Damm 已提交
694 695
config SPI_SH_SCI
	tristate "SuperH SCI SPI controller"
R
Robert P. J. Day 已提交
696
	depends on SUPERH
M
Magnus Damm 已提交
697 698 699 700
	select SPI_BITBANG
	help
	  SPI driver for SuperH SCI blocks.

701 702
config SPI_SH_HSPI
	tristate "SuperH HSPI controller"
703
	depends on ARCH_RENESAS || COMPILE_TEST
704 705 706
	help
	  SPI driver for SuperH HSPI blocks.

707 708 709 710 711 712
config SPI_SIFIVE
	tristate "SiFive SPI controller"
	depends on HAS_IOMEM
	help
	  This exposes the SPI controller IP from SiFive.

713 714
config SPI_SIRF
	tristate "CSR SiRFprimaII SPI controller"
M
Mark Brown 已提交
715
	depends on SIRF_DMA
716 717 718 719
	select SPI_BITBANG
	help
	  SPI driver for CSR SiRFprimaII SoCs

720 721 722 723 724 725 726 727 728 729
config SPI_SLAVE_MT27XX
	tristate "MediaTek SPI slave device"
	depends on ARCH_MEDIATEK || COMPILE_TEST
	depends on SPI_SLAVE
	help
	  This selects the MediaTek(R) SPI slave device driver.
	  If you want to use MediaTek(R) SPI slave interface,
	  say Y or M here.If you are not sure, say N.
	  SPI slave drivers for Mediatek MT27XX series ARM SoCs.

730 731 732 733 734 735
config SPI_SPRD
	tristate "Spreadtrum SPI controller"
	depends on ARCH_SPRD || COMPILE_TEST
	help
	  SPI driver for Spreadtrum SoCs.

736 737 738
config SPI_SPRD_ADI
	tristate "Spreadtrum ADI controller"
	depends on ARCH_SPRD || COMPILE_TEST
739
	depends on HWSPINLOCK || (COMPILE_TEST && !HWSPINLOCK)
740 741 742
	help
	  ADI driver based on SPI for Spreadtrum SoCs.

743 744 745 746
config SPI_STM32
	tristate "STMicroelectronics STM32 SPI controller"
	depends on ARCH_STM32 || COMPILE_TEST
	help
747
	  SPI driver for STMicroelectronics STM32 SoCs.
748 749 750 751 752

	  STM32 SPI controller supports DMA and PIO modes. When DMA
	  is not available, the driver automatically falls back to
	  PIO mode.

753 754 755 756 757 758 759 760 761
config SPI_STM32_QSPI
	tristate "STMicroelectronics STM32 QUAD SPI controller"
	depends on ARCH_STM32 || COMPILE_TEST
	depends on OF
	help
	  This enables support for the Quad SPI controller in master mode.
	  This driver does not support generic SPI. The implementation only
	  supports spi-mem interface.

762 763
config SPI_ST_SSC4
	tristate "STMicroelectronics SPI SSC-based driver"
764
	depends on ARCH_STI || COMPILE_TEST
765 766 767 768
	help
	  STMicroelectronics SoCs support for SPI. If you say yes to
	  this option, support will be included for the SSC driven SPI.

769 770 771 772 773 774
config SPI_SUN4I
	tristate "Allwinner A10 SoCs SPI controller"
	depends on ARCH_SUNXI || COMPILE_TEST
	help
	  SPI driver for Allwinner sun4i, sun5i and sun7i SoCs

775 776 777
config SPI_SUN6I
	tristate "Allwinner A31 SPI controller"
	depends on ARCH_SUNXI || COMPILE_TEST
778
	depends on RESET_CONTROLLER
779 780 781
	help
	  This enables using the SPI controller on the Allwinner A31 SoCs.

782 783 784 785 786 787 788 789 790 791
config SPI_SYNQUACER
	tristate "Socionext's SynQuacer HighSpeed SPI controller"
	depends on ARCH_SYNQUACER || COMPILE_TEST
	help
	  SPI driver for Socionext's High speed SPI controller which provides
	  various operating modes for interfacing to serial peripheral devices
	  that use the de-facto standard SPI protocol.

	  It also supports the new dual-bit and quad-bit SPI protocol.

M
Mason Yang 已提交
792
config SPI_MXIC
K
Krzysztof Kozlowski 已提交
793 794 795 796
	tristate "Macronix MX25F0A SPI controller"
	depends on SPI_MASTER
	help
	  This selects the Macronix MX25F0A SPI controller driver.
M
Mason Yang 已提交
797

798 799 800 801 802 803 804
config SPI_MXS
	tristate "Freescale MXS SPI controller"
	depends on ARCH_MXS
	select STMP_DEVICE
	help
	  SPI driver for Freescale MXS devices.

L
Laxman Dewangan 已提交
805 806
config SPI_TEGRA114
	tristate "NVIDIA Tegra114 SPI Controller"
807
	depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
808
	depends on RESET_CONTROLLER
L
Laxman Dewangan 已提交
809 810 811 812 813
	help
	  SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
	  is different than the older SoCs SPI controller and also register interface
	  get changed with this controller.

814 815
config SPI_TEGRA20_SFLASH
	tristate "Nvidia Tegra20 Serial flash Controller"
816
	depends on ARCH_TEGRA || COMPILE_TEST
S
Stephen Warren 已提交
817
	depends on RESET_CONTROLLER
818 819 820 821 822
	help
	  SPI driver for Nvidia Tegra20 Serial flash Controller interface.
	  The main usecase of this controller is to use spi flash as boot
	  device.

823 824
config SPI_TEGRA20_SLINK
	tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
825
	depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
826
	depends on RESET_CONTROLLER
827 828 829
	help
	  SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.

J
Jan Glauber 已提交
830 831 832 833 834 835 836
config SPI_THUNDERX
	tristate "Cavium ThunderX SPI controller"
	depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
	help
	  SPI host driver for the hardware found on Cavium ThunderX
	  SOCs.

837
config SPI_TOPCLIFF_PCH
838
	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
839
	depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
840
	help
841 842
	  SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
	  used in some x86 embedded processors.
843

844 845
	  This driver also supports the ML7213/ML7223/ML7831, a companion chip
	  for the Atom E6xx series and compatible with the Intel EG20T PCH.
846

A
Atsushi Nemoto 已提交
847 848
config SPI_TXX9
	tristate "Toshiba TXx9 SPI controller"
849
	depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
A
Atsushi Nemoto 已提交
850 851 852
	help
	  SPI driver for Toshiba TXx9 MIPS SoCs

853 854 855
config SPI_UNIPHIER
	tristate "Socionext UniPhier SPI Controller"
	depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
856
	depends on HAS_IOMEM
857 858 859 860 861 862 863 864 865 866
	help
	  This enables a driver for the Socionext UniPhier SoC SCSSI SPI controller.

	  UniPhier SoCs have SCSSI and MCSSI SPI controllers.
	  Every UniPhier SoC has SCSSI which supports single channel.
	  Older UniPhier Pro4/Pro5 also has MCSSI which support multiple channels.
	  This driver supports SCSSI only.

	  If your SoC supports SCSSI, say Y here.

867 868 869 870 871 872 873
config SPI_XCOMM
	tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
	depends on I2C
	help
	  Support for the SPI-I2C bridge found on the Analog Devices
	  AD-FMCOMMS1-EBZ board.

874
config SPI_XILINX
875
	tristate "Xilinx SPI controller common module"
876
	depends on HAS_IOMEM
877 878 879 880 881 882 883
	select SPI_BITBANG
	help
	  This exposes the SPI controller IP from the Xilinx EDK.

	  See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
	  Product Specification document (DS464) for hardware details.

884 885
	  Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"

886 887
config SPI_XLP
	tristate "Netlogic XLP SPI controller driver"
888
	depends on CPU_XLP || ARCH_THUNDER2 || COMPILE_TEST
889 890 891 892 893 894 895 896
	help
	  Enable support for the SPI controller on the Netlogic XLP SoCs.
	  Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
	  and XLP5XX.

	  If you have a Netlogic XLP platform say Y here.
	  If unsure, say N.

897 898
config SPI_XTENSA_XTFPGA
	tristate "Xtensa SPI controller for xtfpga"
899
	depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
900 901 902 903 904 905 906 907 908
	select SPI_BITBANG
	help
	  SPI driver for xtfpga SPI master controller.

	  This simple SPI master controller is built into xtfpga bitstreams
	  and is used to control daughterboard audio codec. It always transfers
	  16 bit words in SPI mode 0, automatically asserting CS on transfer
	  start and deasserting on end.

909 910 911 912 913 914 915 916
config SPI_ZYNQ_QSPI
	tristate "Xilinx Zynq QSPI controller"
	depends on ARCH_ZYNQ || COMPILE_TEST
	help
	  This enables support for the Zynq Quad SPI controller
	  in master mode.
	  This controller only supports SPI memory interface.

917 918
config SPI_ZYNQMP_GQSPI
	tristate "Xilinx ZynqMP GQSPI controller"
919
	depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
920 921 922
	help
	  Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.

923 924 925 926 927 928
config SPI_AMD
	tristate "AMD SPI controller"
	depends on SPI_MASTER || COMPILE_TEST
	help
	  Enables SPI controller driver for AMD SoC.

929 930 931 932
#
# Add new SPI master controllers in alphabetical order above this line
#

C
Chris Packham 已提交
933 934 935 936 937 938 939 940 941 942 943
comment "SPI Multiplexer support"

config SPI_MUX
	tristate "SPI multiplexer support"
	select MULTIPLEXER
	help
	  This adds support for SPI multiplexers. Each SPI mux will be
	  accessible as a SPI controller, the devices behind the mux will appear
	  to be chip selects on this controller. It is still necessary to
	  select one or more specific mux-controller drivers.

944 945 946 947 948 949
#
# There are lots of SPI device types, with sensors and memory
# being probably the most widely used ones.
#
comment "SPI Protocol Masters"

A
Andrea Paterniani 已提交
950 951 952 953 954 955 956 957
config SPI_SPIDEV
	tristate "User mode SPI device driver support"
	help
	  This supports user mode SPI protocol drivers.

	  Note that this application programming interface is EXPERIMENTAL
	  and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.

958 959 960 961 962 963 964 965 966
config SPI_LOOPBACK_TEST
	tristate "spi loopback test framework support"
	depends on m
	help
	  This enables the SPI loopback testing framework driver

	  primarily used for development of spi_master drivers
	  and to detect regressions

B
Ben Dooks 已提交
967 968
config SPI_TLE62X0
	tristate "Infineon TLE62X0 (for power switching)"
R
Robert P. J. Day 已提交
969
	depends on SYSFS
B
Ben Dooks 已提交
970 971 972 973 974 975
	help
	  SPI driver for Infineon TLE62X0 series line driver chips,
	  such as the TLE6220, TLE6230 and TLE6240.  This provides a
	  sysfs interface, with each line presented as a kind of GPIO
	  exposing both switch control and diagnostic feedback.

976 977 978 979
#
# Add new SPI protocol masters in alphabetical order above this line
#

R
Robert P. J. Day 已提交
980 981
endif # SPI_MASTER

982 983 984 985 986 987 988 989 990 991 992 993
#
# SLAVE side ... listening to other SPI masters
#

config SPI_SLAVE
	bool "SPI slave protocol handlers"
	help
	  If your system has a slave-capable SPI controller, you can enable
	  slave protocol handlers.

if SPI_SLAVE

994 995 996 997 998 999
config SPI_SLAVE_TIME
	tristate "SPI slave handler reporting boot up time"
	help
	  SPI slave handler responding with the time of reception of the last
	  SPI message.

1000 1001 1002 1003 1004 1005
config SPI_SLAVE_SYSTEM_CONTROL
	tristate "SPI slave handler controlling system state"
	help
	  SPI slave handler to allow remote control of system reboot, power
	  off, halt, and suspend.

1006
endif # SPI_SLAVE
1007

1008
endif # SPI