spi: tegra: add spi driver for SLINK controller

Tegra20/Tegra30 supports the spi interface through its SLINK
controller. Add spi driver for SLINK controller.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt

+NVIDIA Tegra20/Tegra30 SLINK controller.
+
+Required properties:
+- compatible : should be "nvidia,tegra20-slink", "nvidia,tegra30-slink".
+- reg: Should contain SLINK registers location and length.
+- interrupts: Should contain SLINK interrupts.
+- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
+  request selector for this SLINK controller.
+
+Recommended properties:
+- spi-max-frequency: Definition as per
+                     Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+slink@7000d600 {
+	compatible = "nvidia,tegra20-slink";
+	reg = <0x7000d600 0x200>;
+	interrupts = <0 82 0x04>;
+	nvidia,dma-request-selector = <&apbdma 16>;
+	spi-max-frequency = <25000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "disabled";
+};
+

drivers/spi/Kconfig

@@ -385,6 +385,12 @@ config SPI_MXS
 	help
 	  SPI driver for Freescale MXS devices.
 
+config SPI_TEGRA20_SLINK
+	tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
+	depends on ARCH_TEGRA && TEGRA20_APB_DMA
+	help
+	  SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
+
 config SPI_TI_SSP
 	tristate "TI Sequencer Serial Port - SPI Support"
 	depends on MFD_TI_SSP

drivers/spi/Makefile

@@ -60,10 +60,10 @@ obj-$(CONFIG_SPI_SH_MSIOF)		+= spi-sh-msiof.o
 obj-$(CONFIG_SPI_SH_SCI)		+= spi-sh-sci.o
 obj-$(CONFIG_SPI_SIRF)		+= spi-sirf.o
 obj-$(CONFIG_SPI_STMP3XXX)		+= spi-stmp.o
+obj-$(CONFIG_SPI_TEGRA20_SLINK)		+= spi-tegra20-slink.o
 obj-$(CONFIG_SPI_TI_SSP)		+= spi-ti-ssp.o
 obj-$(CONFIG_SPI_TLE62X0)		+= spi-tle62x0.o
 obj-$(CONFIG_SPI_TOPCLIFF_PCH)		+= spi-topcliff-pch.o
 obj-$(CONFIG_SPI_TXX9)			+= spi-txx9.o
 obj-$(CONFIG_SPI_XCOMM)		+= spi-xcomm.o
 obj-$(CONFIG_SPI_XILINX)		+= spi-xilinx.o
-

include/linux/spi/spi-tegra.h

+/*
+ * spi-tegra.h: SPI interface for Nvidia Tegra20 SLINK controller.
+ *
+ * Copyright (C) 2011 NVIDIA Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef _LINUX_SPI_TEGRA_H
+#define _LINUX_SPI_TEGRA_H
+
+struct tegra_spi_platform_data {
+	int dma_req_sel;
+	unsigned int spi_max_frequency;
+};
+
+/*
+ * Controller data from device to pass some info like
+ * hw based chip select can be used or not and if yes
+ * then CS hold and setup time.
+ */
+struct tegra_spi_device_controller_data {
+	bool is_hw_based_cs;
+	int cs_setup_clk_count;
+	int cs_hold_clk_count;
+};
+
+#endif /* _LINUX_SPI_TEGRA_H */