The "powered-down" cpuidle mode of Tegra20 needs the CPU0 be the last one
core to go into this mode before other core. The coupled cpuidle framework
can help to sync the MPCore to coupled state then go into "powered-down"
idle mode together. The driver can just assume the MPCore come into
"powered-down" mode at the same time. No need to take care if the CPU_0
goes into this mode along and only can put it into safe idle mode (WFI).

The powered-down state of Tegra20 requires power gating both CPU cores.
When the secondary CPU requests to enter powered-down state, it saves
its own contexts and then enters WFI for waiting CPU0 in the same state.
When the CPU0 requests powered-down state, it attempts to put the secondary
CPU into reset to prevent it from waking up. Then power down both CPUs
together and power off the cpu rail.

Be aware of that, you may see the legacy power state "LP2" in the code
which is exactly the same meaning of "CPU power down".

Based on the work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NColin Cross <ccross@android.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Updating the cache maintenance order before CPU shutdown when doing CPU
hotplug.
The old order:
* clean L1 by flush_cache_all
* exit SMP
* CPU shutdown
Adapt to:
* disable L1 data cache by clear C bit
* clean L1 by v7_flush_dcache_louis
* exit SMP
* CPU shutdown

For CPU hotplug case, it's no need to do "flush_cache_all". And we should
disable L1 data cache before clean L1 data cache. Then leaving the SMP
coherency.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The L2 RAM is in different power domain from the CPU cluster. So the
L2 content can be retained over CPU suspend/resume. To do that, we
need to disable L2 after the MMU is disabled, and enable L2 before
the MMU is enabled. But the L2 controller is in the same power domain
with the CPU cluster. We need to restore it's settings and re-enable
it after the power be resumed.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This is a power gating idle mode. It support power gating vdd_cpu rail
after all cpu cores in "powered-down" status. For Tegra30, the CPU0 can
enter this state only when all secondary CPU is offline. We need to take
care and make sure whole secondary CPUs were offline and checking the
CPU power gate status. After that, the CPU0 can go into "powered-down"
state safely. Then shut off the CPU rail.

Be aware of that, you may see the legacy power state "LP2" in the code
which is exactly the same meaning of "CPU power down".

Base on the work by:
Scott Williams <scwilliams@nvidia.com>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This supports power-gated idle on secondary CPUs for Tegra30. The
secondary CPUs can go into powered-down state independently. When
CPU goes into this state, it saves it's contexts and puts itself
to flow controlled WFI state. After that, it will been power gated.

Be aware of that, you may see the legacy power state "LP2" in the
code which is exactly the same meaning of "CPU power down".

Based on the work by:
Scott Williams <scwilliams@nvidia.com>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Nothing outside mach-tegra uses this file, so there's no need for it to
be in <mach/>.

Since uncompress.h and debug-macro.S remain in include/mach, they need
to include "../../iomap.h" becaue of this change. uncompress.h will soon
be deleted in later multi-platform/single-zImage patches. debug-macro.S
will need to continue to include this header using an explicit relative
path, to avoid duplicating the physical->virtual address mapping that
iomap.h dictates.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

There are some common macros for Tegra low-level assembly code. Clean
up them into one header file and move the definitions that will be
re-used into it as well.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This particular code had no effect on WFI execution. It only
asserts/de-asserts signal to tegra "legacy" CPU idle stats
monitor, which we are no longer using (cpufreq is based on
kernel s/w idle stats instead).
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Commit 6f6f6a70 "ARM: create a common IOMEM definition" moved macro
IOMEM(), and requires users to include <asm/assembler.h>. Fix Tegra's
sleep.S to do so. This fixes:

arch/arm/mach-tegra/sleep.S: Assembler messages:
arch/arm/mach-tegra/sleep.S:77: Error: missing ')'
arch/arm/mach-tegra/sleep.S:77: Error: garbage following instruction
    -- `movw r0,#:lower16:(0x60007000-0x60000000+IOMEM(0xFE200000))'

Note: This only shows up after 0a258935 "ARM: tegra: update defconfig"
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>

Configure the flow controller for clockgating and enter WFI

Based on work by:

Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NColin Cross <ccross@android.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>