mtd: m25p80: Add dual read support

Add support for Dual SPI read transfers, which is supported by some
Spansion SPI FLASHes.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

drivers/mtd/devices/m25p80.c

@@ -41,7 +41,8 @@
 #define	OPCODE_WRSR		0x01	/* Write status register 1 byte */
 #define	OPCODE_NORM_READ	0x03	/* Read data bytes (low frequency) */
 #define	OPCODE_FAST_READ	0x0b	/* Read data bytes (high frequency) */
-#define	OPCODE_QUAD_READ        0x6b    /* Read data bytes */
+#define	OPCODE_DUAL_READ        0x3b    /* Read data bytes (Dual SPI) */
+#define	OPCODE_QUAD_READ        0x6b    /* Read data bytes (Quad SPI) */
 #define	OPCODE_PP		0x02	/* Page program (up to 256 bytes) */
 #define	OPCODE_BE_4K		0x20	/* Erase 4KiB block */
 #define	OPCODE_BE_4K_PMC	0xd7	/* Erase 4KiB block on PMC chips */
@@ -54,7 +55,8 @@
 /* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
 #define	OPCODE_NORM_READ_4B	0x13	/* Read data bytes (low frequency) */
 #define	OPCODE_FAST_READ_4B	0x0c	/* Read data bytes (high frequency) */
-#define	OPCODE_QUAD_READ_4B	0x6c    /* Read data bytes */
+#define	OPCODE_DUAL_READ_4B	0x3c    /* Read data bytes (Dual SPI) */
+#define	OPCODE_QUAD_READ_4B	0x6c    /* Read data bytes (Quad SPI) */
 #define	OPCODE_PP_4B		0x12	/* Page program (up to 256 bytes) */
 #define	OPCODE_SE_4B		0xdc	/* Sector erase (usually 64KiB) */
 
@@ -95,6 +97,7 @@
 enum read_type {
 	M25P80_NORMAL = 0,
 	M25P80_FAST,
+	M25P80_DUAL,
 	M25P80_QUAD,
 };
 
@@ -479,6 +482,7 @@ static inline int m25p80_dummy_cycles_read(struct m25p *flash)
 {
 	switch (flash->flash_read) {
 	case M25P80_FAST:
+	case M25P80_DUAL:
 	case M25P80_QUAD:
 		return 1;
 	case M25P80_NORMAL:
@@ -492,6 +496,8 @@ static inline int m25p80_dummy_cycles_read(struct m25p *flash)
 static inline unsigned int m25p80_rx_nbits(const struct m25p *flash)
 {
 	switch (flash->flash_read) {
+	case M25P80_DUAL:
+		return 2;
 	case M25P80_QUAD:
 		return 4;
 	default:
@@ -855,7 +861,8 @@ struct flash_info {
 #define	SST_WRITE	0x04		/* use SST byte programming */
 #define	M25P_NO_FR	0x08		/* Can't do fastread */
 #define	SECT_4K_PMC	0x10		/* OPCODE_BE_4K_PMC works uniformly */
-#define	M25P80_QUAD_READ	0x20    /* Flash supports Quad Read */
+#define	M25P80_DUAL_READ	0x20    /* Flash supports Dual Read */
+#define	M25P80_QUAD_READ	0x40    /* Flash supports Quad Read */
 };
 
 #define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags)	\
@@ -1226,7 +1233,7 @@ static int m25p_probe(struct spi_device *spi)
 	if (info->flags & M25P_NO_FR)
 		flash->flash_read = M25P80_NORMAL;
 
-	/* Quad-read mode takes precedence over fast/normal */
+	/* Quad/Dual-read mode takes precedence over fast/normal */
 	if (spi->mode & SPI_RX_QUAD && info->flags & M25P80_QUAD_READ) {
 		ret = set_quad_mode(flash, info->jedec_id);
 		if (ret) {
@@ -1234,6 +1241,8 @@ static int m25p_probe(struct spi_device *spi)
 			return ret;
 		}
 		flash->flash_read = M25P80_QUAD;
+	} else if (spi->mode & SPI_RX_DUAL && info->flags & M25P80_DUAL_READ) {
+		flash->flash_read = M25P80_DUAL;
 	}
 
 	/* Default commands */
@@ -1241,6 +1250,9 @@ static int m25p_probe(struct spi_device *spi)
 	case M25P80_QUAD:
 		flash->read_opcode = OPCODE_QUAD_READ;
 		break;
+	case M25P80_DUAL:
+		flash->read_opcode = OPCODE_DUAL_READ;
+		break;
 	case M25P80_FAST:
 		flash->read_opcode = OPCODE_FAST_READ;
 		break;
@@ -1265,6 +1277,9 @@ static int m25p_probe(struct spi_device *spi)
 			case M25P80_QUAD:
 				flash->read_opcode = OPCODE_QUAD_READ_4B;
 				break;
+			case M25P80_DUAL:
+				flash->read_opcode = OPCODE_DUAL_READ_4B;
+				break;
 			case M25P80_FAST:
 				flash->read_opcode = OPCODE_FAST_READ_4B;
 				break;