ARM: dts: imx: add device tree support for Freescale imx50evk board

Add device tree support for the Freescale IMX50EVk board based around the
IMX50 SoC. Supports UART, SPI flash, FEC ethernet and USB on this board.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

arch/arm/boot/dts/Makefile

@@ -143,6 +143,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx27-phytec-phycard-s-som.dtb \
 	imx27-phytec-phycard-s-rdk.dtb \
 	imx31-bug.dtb \
+	imx50-evk.dtb \
 	imx51-apf51.dtb \
 	imx51-apf51dev.dtb \
 	imx51-babbage.dtb \

arch/arm/boot/dts/imx50-evk.dts

+/*
+ * Copyright 2013 Greg Ungerer <gerg@uclinux.org>
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx50.dtsi"
+
+/ {
+	model = "Freescale i.MX50 Evaluation Kit";
+	compatible = "fsl,imx50-evk", "fsl,imx50";
+
+	memory {
+		reg = <0x70000000 0x80000000>;
+	};
+};
+
+&cspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cspi>;
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio4 11 0>, <&gpio4 13 0>;
+	status = "okay";
+
+	flash: m25p32@1 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p32", "m25p80";
+		spi-max-frequency = <25000000>;
+		reg = <1>;
+
+		partition@0 {
+			label = "bootloader";
+			reg = <0x0 0x100000>;
+			read-only;
+		};
+
+		partition@100000 {
+			label = "kernel";
+			reg = <0x100000 0x300000>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio4 12 0>;
+	status = "okay";
+};
+
+&iomuxc {
+	imx50-evk {
+		pinctrl_cspi: cspigrp {
+			fsl,pins = <
+				MX50_PAD_CSPI_SCLK__CSPI_SCLK		0x00
+				MX50_PAD_CSPI_MISO__CSPI_MISO		0x00
+				MX50_PAD_CSPI_MOSI__CSPI_MOSI		0x00
+				MX50_PAD_CSPI_SS0__GPIO4_11		0xc4
+				MX50_PAD_ECSPI1_MOSI__CSPI_SS1		0xf4
+			>;
+		};
+
+		pinctrl_fec: fecgrp {
+			fsl,pins = <
+				MX50_PAD_SSI_RXFS__FEC_MDC		0x80
+				MX50_PAD_SSI_RXC__FEC_MDIO		0x80
+				MX50_PAD_DISP_D0__FEC_TX_CLK		0x80
+				MX50_PAD_DISP_D1__FEC_RX_ERR		0x80
+				MX50_PAD_DISP_D2__FEC_RX_DV		0x80
+				MX50_PAD_DISP_D3__FEC_RDATA_1		0x80
+				MX50_PAD_DISP_D4__FEC_RDATA_0		0x80
+				MX50_PAD_DISP_D5__FEC_TX_EN		0x80
+				MX50_PAD_DISP_D6__FEC_TDATA_1		0x80
+				MX50_PAD_DISP_D7__FEC_TDATA_0		0x80
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				MX50_PAD_UART1_TXD__UART1_TXD_MUX	0x1e4
+				MX50_PAD_UART1_RXD__UART1_RXD_MUX	0x1e4
+				MX50_PAD_UART1_RTS__UART1_RTS		0x1e4
+				MX50_PAD_UART1_CTS__UART1_CTS		0x1e4
+			>;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbh2 {
+	status = "okay";
+};
+
+&usbh3 {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};