Kconfig 22.1 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3 4 5
#
# USB Host Controller Drivers
#
comment "USB Host Controller Drivers"

6 7 8 9 10 11 12 13 14 15 16 17
config USB_C67X00_HCD
	tristate "Cypress C67x00 HCD support"
	help
	  The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
	  host/peripheral/OTG USB controllers.

	  Enable this option to support this chip in host controller mode.
	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called c67x00.

18
config USB_XHCI_HCD
19
	tristate "xHCI HCD (USB 3.0) support"
20
	depends on USB_ARCH_HAS_XHCI
21 22 23 24 25 26 27
	---help---
	  The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
	  "SuperSpeed" host controller hardware.

	  To compile this driver as a module, choose M here: the
	  module will be called xhci-hcd.

28 29
if USB_XHCI_HCD

30 31 32
config USB_XHCI_PLATFORM
	tristate

33 34 35 36 37 38 39 40 41
config USB_XHCI_HCD_DEBUGGING
	bool "Debugging for the xHCI host controller"
	---help---
	  Say 'Y' to turn on debugging for the xHCI host controller driver.
	  This will spew debugging output, even in interrupt context.
	  This should only be used for debugging xHCI driver bugs.

	  If unsure, say N.

42 43
endif # USB_XHCI_HCD

L
Linus Torvalds 已提交
44 45
config USB_EHCI_HCD
	tristate "EHCI HCD (USB 2.0) support"
46
	depends on USB_ARCH_HAS_EHCI
L
Linus Torvalds 已提交
47 48 49 50
	---help---
	  The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
	  "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
	  If your USB host controller supports USB 2.0, you will likely want to
51
	  configure this Host Controller Driver.
L
Linus Torvalds 已提交
52 53 54

	  EHCI controllers are packaged with "companion" host controllers (OHCI
	  or UHCI) to handle USB 1.1 devices connected to root hub ports.  Ports
55
	  will connect to EHCI if the device is high speed, otherwise they
L
Linus Torvalds 已提交
56 57 58 59 60 61 62 63 64 65 66
	  connect to a companion controller.  If you configure EHCI, you should
	  probably configure the OHCI (for NEC and some other vendors) USB Host
	  Controller Driver or UHCI (for Via motherboards) Host Controller
	  Driver too.

	  You may want to read <file:Documentation/usb/ehci.txt>.

	  To compile this driver as a module, choose M here: the
	  module will be called ehci-hcd.

config USB_EHCI_ROOT_HUB_TT
67
	bool "Root Hub Transaction Translators"
68
	depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST
L
Linus Torvalds 已提交
69 70 71 72 73 74
	---help---
	  Some EHCI chips have vendor-specific extensions to integrate
	  transaction translators, so that no OHCI or UHCI companion
	  controller is needed.  It's safe to say "y" even if your
	  controller doesn't support this feature.

75 76 77 78
	  This supports the EHCI implementation that's originally
	  from ARC, and has since changed hands a few times.

config USB_EHCI_TT_NEWSCHED
79
	bool "Improved Transaction Translator scheduling"
80
	depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST
81
	default y
82 83 84 85 86 87 88 89 90 91
	---help---
	  This changes the periodic scheduling code to fill more of the low
	  and full speed bandwidth available from the Transaction Translator
	  (TT) in USB 2.0 hubs.  Without this, only one transfer will be
	  issued in each microframe, significantly reducing the number of
	  periodic low/fullspeed transfers possible.

	  If you have multiple periodic low/fullspeed devices connected to a
	  highspeed USB hub which is connected to a highspeed USB Host
	  Controller, and some of those devices will not work correctly
92 93 94
	  (possibly due to "ENOSPC" or "-28" errors), say Y.  Conversely, if
	  you have only one such device and it doesn't work, you could try
	  saying N.
95

96
	  If unsure, say Y.
L
Linus Torvalds 已提交
97

98 99 100 101 102
config USB_FSL_MPH_DR_OF
	tristate

if USB_EHCI_HCD

103 104
config USB_EHCI_PCI
	tristate
105
	depends on PCI
106 107
	default y

108 109
config USB_EHCI_HCD_PMC_MSP
	tristate "EHCI support for on-chip PMC MSP71xx USB controller"
110
	depends on MSP_HAS_USB
111 112 113 114 115 116 117
	default n
	select USB_EHCI_BIG_ENDIAN_DESC
	select USB_EHCI_BIG_ENDIAN_MMIO
	---help---
		Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
		If unsure, say N.

118 119 120
config USB_EHCI_BIG_ENDIAN_MMIO
	bool

121 122 123
config USB_EHCI_BIG_ENDIAN_DESC
	bool

124 125
config XPS_USB_HCD_XILINX
	bool "Use Xilinx usb host EHCI controller core"
126
	depends on (PPC32 || MICROBLAZE)
127 128 129 130 131 132 133 134
	select USB_EHCI_BIG_ENDIAN_DESC
	select USB_EHCI_BIG_ENDIAN_MMIO
	---help---
		Xilinx xps USB host controller core is EHCI compilant and has
		transaction translator built-in. It can be configured to either
		support both high speed and full speed devices, or high speed
		devices only.

135
config USB_EHCI_FSL
136
	bool "Support for Freescale PPC on-chip EHCI USB controller"
137
	depends on FSL_SOC
138
	select USB_EHCI_ROOT_HUB_TT
139
	select USB_FSL_MPH_DR_OF if OF
140 141 142 143
	---help---
	  Variation of ARC USB block used in some Freescale chips.

config USB_EHCI_MXC
144
	tristate "Support for Freescale i.MX on-chip EHCI USB controller"
145
	depends on ARCH_MXC
146
	select USB_EHCI_ROOT_HUB_TT
147 148 149
	---help---
	  Variation of ARC USB block used in some Freescale chips.

150
config USB_EHCI_HCD_OMAP
151
	tristate "EHCI support for OMAP3 and later chips"
152
	depends on ARCH_OMAP
153
	default y
154
	---help---
155 156
	  Enables support for the on-chip EHCI controller on
	  OMAP3 and later chips.
157 158 159
	  If your system uses a PHY on the USB port, you will need to
	  enable USB_PHY and the appropriate PHY driver as well. Most
	  boards need the NOP_USB_XCEIV PHY driver.
160

161 162 163 164 165 166 167 168 169 170 171
config USB_EHCI_HCD_ORION
	tristate  "Support for Marvell EBU on-chip EHCI USB controller"
	depends on USB_EHCI_HCD && PLAT_ORION
	default y
	---help---
	  Enables support for the on-chip EHCI controller on Marvell's
	  embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP,
	  Armada 370.  This is different from the EHCI implementation
	  on Marvell's mobile PXA and MMP SoC, see "EHCI support for
	  Marvell PXA/MMP USB controller" for those.

172 173 174 175 176 177 178 179
config USB_EHCI_HCD_SPEAR
        tristate "Support for ST SPEAr on-chip EHCI USB controller"
        depends on USB_EHCI_HCD && PLAT_SPEAR
        default y
        ---help---
          Enables support for the on-chip EHCI controller on
          ST SPEAr chips.

180 181 182 183 184 185 186 187
config USB_EHCI_HCD_AT91
        tristate  "Support for Atmel on-chip EHCI USB controller"
        depends on USB_EHCI_HCD && ARCH_AT91
        default y
        ---help---
          Enables support for the on-chip EHCI controller on
          Atmel chips.

188
config USB_EHCI_MSM
189
	tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller"
190
	depends on ARCH_MSM
191
	depends on USB_PHY
192
	select USB_EHCI_ROOT_HUB_TT
193
	select USB_MSM_OTG
194 195 196 197
	---help---
	  Enables support for the USB Host controller present on the
	  Qualcomm chipsets. Root Hub has inbuilt TT.
	  This driver depends on OTG driver for PHY initialization,
198
	  clock management, powering up VBUS, and power management.
199 200
	  This driver is not supported on boards like trout which
	  has an external PHY.
201

202 203
config USB_EHCI_TEGRA
       boolean "NVIDIA Tegra HCD support"
204
       depends on ARCH_TEGRA
205
       select USB_EHCI_ROOT_HUB_TT
206
       select USB_PHY
207 208 209 210
       help
         This driver enables support for the internal USB Host Controllers
         found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.

211 212
config USB_EHCI_HCD_PPC_OF
	bool "EHCI support for PPC USB controller on OF platform bus"
213
	depends on PPC_OF
214 215 216 217 218
	default y
	---help---
	  Enables support for the USB controller present on the PowerPC
	  OpenFirmware platform bus.

219 220
config USB_EHCI_SH
	bool "EHCI support for SuperH USB controller"
221
	depends on SUPERH
222 223 224 225
	---help---
	  Enables support for the on-chip EHCI controller on the SuperH.
	  If you use the PCI EHCI controller, this option is not necessary.

226
config USB_EHCI_S5P
227
       tristate "EHCI support for Samsung S5P/EXYNOS SoC Series"
228
       depends on PLAT_S5P
229
       help
230 231
	Enable support for the Samsung S5Pxxxx and Exynos3/4/5 SOC's
	on-chip EHCI controller.
232

233
config USB_EHCI_MV
234
	bool "EHCI support for Marvell PXA/MMP USB controller"
235
	depends on (ARCH_PXA || ARCH_MMP)
236 237 238 239 240
	select USB_EHCI_ROOT_HUB_TT
	---help---
	  Enables support for Marvell (including PXA and MMP series) on-chip
	  USB SPH and OTG controller. SPH is a single port host, and it can
	  only be EHCI host. OTG is controller that can switch to host mode.
241 242 243 244
	  Note that this driver will not work on Marvell's other EHCI
	  controller used by the EBU-type SoCs including Orion, Kirkwood,
	  Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
	  on-chip EHCI USB controller" for those.
245

246 247
config USB_W90X900_EHCI
	bool "W90X900(W90P910) EHCI support"
248
	depends on ARCH_W90X900
249 250 251
	---help---
		Enables support for the W90X900 USB controller

252
config USB_CNS3XXX_EHCI
253
	bool "Cavium CNS3XXX EHCI Module (DEPRECATED)"
254
	depends on ARCH_CNS3XXX
255
	select USB_EHCI_HCD_PLATFORM
256
	---help---
257 258 259
	  This option is deprecated now and the driver was removed, use
	  USB_EHCI_HCD_PLATFORM instead.

260 261 262 263
	  Enable support for the CNS3XXX SOC's on-chip EHCI controller.
	  It is needed for high-speed (480Mbit/sec) USB 2.0 device
	  support.

264
config USB_EHCI_ATH79
265
	bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)"
266
	depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X)
267
	select USB_EHCI_ROOT_HUB_TT
268
	select USB_EHCI_HCD_PLATFORM
269 270
	default y
	---help---
271 272 273
	  This option is deprecated now and the driver was removed, use
	  USB_EHCI_HCD_PLATFORM instead.

274 275 276
	  Enables support for the built-in EHCI controller present
	  on the Atheros AR7XXX/AR9XXX SoCs.

277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298
config USB_EHCI_HCD_PLATFORM
	tristate "Generic EHCI driver for a platform device"
	default n
	---help---
	  Adds an EHCI host driver for a generic platform device, which
	  provides a memory space and an irq.

	  If unsure, say N.

config USB_OCTEON_EHCI
	bool "Octeon on-chip EHCI support"
	depends on CPU_CAVIUM_OCTEON
	default n
	select USB_EHCI_BIG_ENDIAN_MMIO
	help
	  Enable support for the Octeon II SOC's on-chip EHCI
	  controller.  It is needed for high-speed (480Mbit/sec)
	  USB 2.0 device support.  All CN6XXX based chips with USB are
	  supported.

endif # USB_EHCI_HCD

299 300
config USB_OXU210HP_HCD
	tristate "OXU210HP HCD support"
301
	depends on GENERIC_HARDIRQS
302 303 304 305 306 307 308 309 310 311
	---help---
	  The OXU210HP is an USB host/OTG/device controller. Enable this
	  option if your board has this chip. If unsure, say N.

	  This driver does not support isochronous transfers and doesn't
	  implement OTG nor USB device controllers.

	  To compile this driver as a module, choose M here: the
	  module will be called oxu210hp-hcd.

312 313 314 315 316 317 318 319 320 321 322
config USB_ISP116X_HCD
	tristate "ISP116X HCD support"
	---help---
	  The ISP1160 and ISP1161 chips are USB host controllers. Enable this
	  option if your board has this chip. If unsure, say N.

	  This driver does not support isochronous transfers.

	  To compile this driver as a module, choose M here: the
	  module will be called isp116x-hcd.

S
Sebastian Siewior 已提交
323 324 325 326 327 328
config USB_ISP1760_HCD
	tristate "ISP 1760 HCD support"
	---help---
	  The ISP1760 chip is a USB 2.0 host controller.

	  This driver does not support isochronous transfers or OTG.
329 330 331 332
	  This USB controller is usually attached to a non-DMA-Master
	  capable bus. NXP's eval kit brings this chip on PCI card
	  where the chip itself is behind a PLB to simulate such
	  a bus.
S
Sebastian Siewior 已提交
333 334

	  To compile this driver as a module, choose M here: the
335
	  module will be called isp1760.
S
Sebastian Siewior 已提交
336

337 338 339 340 341 342 343 344 345 346 347
config USB_ISP1362_HCD
	tristate "ISP1362 HCD support"
	default N
	---help---
	  Supports the Philips ISP1362 chip as a host controller

	  This driver does not support isochronous transfers.

	  To compile this driver as a module, choose M here: the
	  module will be called isp1362-hcd.

L
Linus Torvalds 已提交
348 349
config USB_OHCI_HCD
	tristate "OHCI HCD support"
350
	depends on USB_ARCH_HAS_OHCI
L
Linus Torvalds 已提交
351
	select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
352
	depends on USB_ISP1301 || !ARCH_LPC32XX
L
Linus Torvalds 已提交
353 354 355 356 357 358 359 360 361 362 363 364 365
	---help---
	  The Open Host Controller Interface (OHCI) is a standard for accessing
	  USB 1.1 host controller hardware.  It does more in hardware than Intel's
	  UHCI specification.  If your USB host controller follows the OHCI spec,
	  say Y.  On most non-x86 systems, and on x86 hardware that's not using a
	  USB controller from Intel or VIA, this is appropriate.  If your host
	  controller doesn't use PCI, this is probably appropriate.  For a PCI
	  based system where you're not sure, the "lspci -v" entry will list the
	  right "prog-if" for your USB controller(s):  EHCI, OHCI, or UHCI.

	  To compile this driver as a module, choose M here: the
	  module will be called ohci-hcd.

366 367
if USB_OHCI_HCD

368 369
config USB_OHCI_HCD_OMAP1
	bool "OHCI support for OMAP1/2 chips"
370
	depends on ARCH_OMAP1
371 372 373 374 375 376
	default y
	---help---
	  Enables support for the OHCI controller on OMAP1/2 chips.

config USB_OHCI_HCD_OMAP3
	bool "OHCI support for OMAP3 and later chips"
377
	depends on (ARCH_OMAP3 || ARCH_OMAP4)
378 379 380 381 382
	default y
	---help---
	  Enables support for the on-chip OHCI controller on
	  OMAP3 and later chips.

383
config USB_OHCI_ATH79
384
	bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)"
385
	depends on (SOC_AR71XX || SOC_AR724X)
386
	select USB_OHCI_HCD_PLATFORM
387 388
	default y
	help
389 390 391
	  This option is deprecated now and the driver was removed, use
	  USB_OHCI_HCD_PLATFORM instead.

392 393 394
	  Enables support for the built-in OHCI controller present on the
	  Atheros AR71XX/AR7240 SoCs.

395
config USB_OHCI_HCD_PPC_OF_BE
A
Arnd Bergmann 已提交
396
	bool "OHCI support for OF platform bus (big endian)"
397
	depends on PPC_OF
398 399
	select USB_OHCI_BIG_ENDIAN_DESC
	select USB_OHCI_BIG_ENDIAN_MMIO
A
Arnd Bergmann 已提交
400 401 402
	---help---
	  Enables support for big-endian USB controllers present on the
	  OpenFirmware platform bus.
403 404

config USB_OHCI_HCD_PPC_OF_LE
A
Arnd Bergmann 已提交
405
	bool "OHCI support for OF platform bus (little endian)"
406
	depends on PPC_OF
407
	select USB_OHCI_LITTLE_ENDIAN
A
Arnd Bergmann 已提交
408 409 410 411 412 413
	---help---
	  Enables support for little-endian USB controllers present on the
	  OpenFirmware platform bus.

config USB_OHCI_HCD_PPC_OF
	bool
414
	depends on PPC_OF
A
Arnd Bergmann 已提交
415
	default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
416

L
Linus Torvalds 已提交
417 418
config USB_OHCI_HCD_PCI
	bool "OHCI support for PCI-bus USB controllers"
419
	depends on PCI && (STB03xxx || PPC_MPC52xx || USB_OHCI_HCD_PPC_OF)
L
Linus Torvalds 已提交
420 421 422 423 424 425
	default y
	select USB_OHCI_LITTLE_ENDIAN
	---help---
	  Enables support for PCI-bus plug-in USB controller cards.
	  If unsure, say Y.

M
Michael Buesch 已提交
426
config USB_OHCI_HCD_SSB
427
	bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
428
	depends on (SSB = y || SSB = USB_OHCI_HCD)
429 430
	select USB_HCD_SSB
	select USB_OHCI_HCD_PLATFORM
M
Michael Buesch 已提交
431 432
	default n
	---help---
433 434 435
	  This option is deprecated now and the driver was removed, use
	  USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.

M
Michael Buesch 已提交
436 437 438 439 440 441 442 443
	  Support for the Sonics Silicon Backplane (SSB) attached
	  Broadcom USB OHCI core.

	  This device is present in some embedded devices with
	  Broadcom based SSB bus.

	  If unsure, say N.

444
config USB_OHCI_SH
445
	bool "OHCI support for SuperH USB controller (DEPRECATED)"
446
	depends on SUPERH
447
	select USB_OHCI_HCD_PLATFORM
448
	---help---
449 450 451
	  This option is deprecated now and the driver was removed, use
	  USB_OHCI_HCD_PLATFORM instead.

452 453 454
	  Enables support for the on-chip OHCI controller on the SuperH.
	  If you use the PCI OHCI controller, this option is not necessary.

J
Jingoo Han 已提交
455 456
config USB_OHCI_EXYNOS
	boolean "OHCI support for Samsung EXYNOS SoC Series"
457
	depends on ARCH_EXYNOS
J
Jingoo Han 已提交
458 459 460
	help
	 Enable support for the Samsung Exynos SOC's on-chip OHCI controller.

461
config USB_CNS3XXX_OHCI
462
	bool "Cavium CNS3XXX OHCI Module (DEPRECATED)"
463
	depends on ARCH_CNS3XXX
464
	select USB_OHCI_HCD_PLATFORM
465
	---help---
466 467 468
	  This option is deprecated now and the driver was removed, use
	  USB_OHCI_HCD_PLATFORM instead.

469 470 471
	  Enable support for the CNS3XXX SOC's on-chip OHCI controller.
	  It is needed for low-speed USB 1.0 device support.

472 473 474 475 476
config USB_OHCI_HCD_PLATFORM
	bool "Generic OHCI driver for a platform device"
	default n
	---help---
	  Adds an OHCI host driver for a generic platform device, which
477
	  provides a memory space and an irq.
478 479 480

	  If unsure, say N.

481 482 483 484 485 486 487 488 489 490 491
config USB_OCTEON_OHCI
	bool "Octeon on-chip OHCI support"
	depends on CPU_CAVIUM_OCTEON
	default USB_OCTEON_EHCI
	select USB_OHCI_BIG_ENDIAN_MMIO
	select USB_OHCI_LITTLE_ENDIAN
	help
	  Enable support for the Octeon II SOC's on-chip OHCI
	  controller.  It is needed for low-speed USB 1.0 device
	  support.  All CN6XXX based chips with USB are supported.

492

493 494 495 496 497
config USB_OHCI_BIG_ENDIAN_DESC
	bool
	default n

config USB_OHCI_BIG_ENDIAN_MMIO
L
Linus Torvalds 已提交
498 499 500 501 502 503 504 505
	bool
	default n

config USB_OHCI_LITTLE_ENDIAN
	bool
	default n if STB03xxx || PPC_MPC52xx
	default y

506 507
endif # USB_OHCI_HCD

L
Linus Torvalds 已提交
508 509
config USB_UHCI_HCD
	tristate "UHCI HCD (most Intel and VIA) support"
510
	depends on PCI || SPARC_LEON || ARCH_VT8500
L
Linus Torvalds 已提交
511 512 513 514 515 516 517 518
	---help---
	  The Universal Host Controller Interface is a standard by Intel for
	  accessing the USB hardware in the PC (which is also called the USB
	  host controller). If your USB host controller conforms to this
	  standard, you may want to say Y, but see below. All recent boards
	  with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
	  i810, i820) conform to this standard. Also all VIA PCI chipsets
	  (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
519 520
	  133) and LEON/GRLIB SoCs with the GRUSBHC controller.
	  If unsure, say Y.
L
Linus Torvalds 已提交
521 522 523 524

	  To compile this driver as a module, choose M here: the
	  module will be called uhci-hcd.

525 526 527
config USB_UHCI_SUPPORT_NON_PCI_HC
	bool
	depends on USB_UHCI_HCD
528 529 530 531 532 533 534 535 536
	default y if (SPARC_LEON || ARCH_VT8500)

config USB_UHCI_PLATFORM
	bool "Generic UHCI Platform Driver support"
	depends on USB_UHCI_SUPPORT_NON_PCI_HC
	default y if ARCH_VT8500
	---help---
	  Enable support for generic UHCI platform devices that require no
	  additional configuration.
537

538
config USB_UHCI_BIG_ENDIAN_MMIO
539
	bool
540 541
	depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
	default y
542 543

config USB_UHCI_BIG_ENDIAN_DESC
544
	bool
545 546
	depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
	default y
547

548 549
config USB_FHCI_HCD
	tristate "Freescale QE USB Host Controller support"
550
	depends on OF_GPIO && QE_GPIO && QUICC_ENGINE
551 552 553 554 555 556 557 558 559 560 561 562
	select FSL_GTM
	select QE_USB
	help
	  This driver enables support for Freescale QE USB Host Controller
	  (as found on MPC8360 and MPC8323 processors), the driver supports
	  Full and Low Speed USB.

config FHCI_DEBUG
	bool "Freescale QE USB Host Controller debug support"
	depends on USB_FHCI_HCD && DEBUG_FS
	help
	  Say "y" to see some FHCI debug information and statistics
L
Lucas De Marchi 已提交
563
	  through debugfs.
564

565 566
config USB_U132_HCD
	tristate "Elan U132 Adapter Host Controller"
567
	depends on USB_FTDI_ELAN
568 569 570 571 572 573 574 575
	default M
	help
	  The U132 adapter is a USB to CardBus adapter specifically designed
	  for PC cards that contain an OHCI host controller. Typical PC cards
	  are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
	  adapter will *NOT* work with PC cards that do not contain an OHCI
	  controller.

M
Matt LaPlante 已提交
576
	  For those PC cards that contain multiple OHCI controllers only the
577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592
	  first one is used.

	  The driver consists of two modules, the "ftdi-elan" module is a
	  USB client driver that interfaces to the FTDI chip within ELAN's
	  USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
	  controller driver that talks to the OHCI controller within the
	  CardBus cards that are inserted in the U132 adapter.

	  This driver has been tested with a CardBus OHCI USB adapter, and
	  worked with a USB PEN Drive inserted into the first USB port of
	  the PCCARD. A rather pointless thing to do, but useful for testing.

	  It is safe to say M here.

	  See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>

L
Linus Torvalds 已提交
593 594 595 596 597 598 599 600 601 602 603
config USB_SL811_HCD
	tristate "SL811HS HCD support"
	help
	  The SL811HS is a single-port USB controller that supports either
	  host side or peripheral side roles.  Enable this option if your
	  board has this chip, and you want to use it as a host controller. 
	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called sl811-hcd.

604 605 606 607 608 609 610 611 612 613
config USB_SL811_HCD_ISO
	bool "partial ISO support"
	depends on USB_SL811_HCD
	help
	  The driver doesn't support iso_frame_desc (yet), but for some simple
	  devices that just queue one ISO frame per URB, then ISO transfers
	  "should" work using the normal urb status fields.

	  If unsure, say N.

614 615 616 617 618 619 620 621 622 623
config USB_SL811_CS
	tristate "CF/PCMCIA support for SL811HS HCD"
	depends on USB_SL811_HCD && PCMCIA
	help
	  Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
	  REX-CFU1U CF card (often used with PDAs).  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called "sl811_cs".

624
config USB_R8A66597_HCD
M
M4rkusXXL 已提交
625
	tristate "R8A66597 HCD support"
626 627 628 629 630 631 632 633 634
	help
	  The R8A66597 is a USB 2.0 host and peripheral controller.

	  Enable this option if your board has this chip, and you want
	  to use it as a host controller.  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called r8a66597-hcd.

635 636 637 638 639 640 641 642 643 644 645 646
config USB_RENESAS_USBHS_HCD
	tristate "Renesas USBHS HCD support"
	depends on USB_RENESAS_USBHS
	help
	  The Renesas USBHS is a USB 2.0 host and peripheral controller.

	  Enable this option if your board has this chip, and you want
	  to use it as a host controller.  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called renesas-usbhs.

D
David Vrabel 已提交
647
config USB_WHCI_HCD
648
	tristate "Wireless USB Host Controller Interface (WHCI) driver"
649
	depends on PCI && USB && UWB
D
David Vrabel 已提交
650 651 652 653 654 655 656 657
	select USB_WUSB
	select UWB_WHCI
	help
	  A driver for PCI-based Wireless USB Host Controllers that are
	  compliant with the WHCI specification.

	  To compile this driver a module, choose M here: the module
	  will be called "whci-hcd".
658 659

config USB_HWA_HCD
660
	tristate "Host Wire Adapter (HWA) driver"
661
	depends on UWB
662 663 664 665 666 667 668 669 670 671
	select USB_WUSB
	select UWB_HWA
	help
	  This driver enables you to connect Wireless USB devices to
	  your system using a Host Wire Adaptor USB dongle. This is an
	  UWB Radio Controller and WUSB Host Controller connected to
	  your machine via USB (specified in WUSB1.0).

	  To compile this driver a module, choose M here: the module
	  will be called "hwa-hc".
672 673

config USB_IMX21_HCD
674
       tristate "i.MX21 HCD support"
675
       depends on ARM && ARCH_MXC
676 677
       help
         This driver enables support for the on-chip USB host in the
678
         i.MX21 processor.
679 680 681 682

         To compile this driver as a module, choose M here: the
         module will be called "imx21-hcd".

683 684 685 686 687


config USB_OCTEON2_COMMON
	bool
	default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI
688 689 690

config USB_HCD_BCMA
	tristate "BCMA usb host driver"
691
	depends on BCMA
692 693 694
	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
	select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
	help
695
	  Enable support for the EHCI and OCHI host controller on an bcma bus.
696 697 698 699
	  It converts the bcma driver into two platform device drivers
	  for ehci and ohci.

	  If unsure, say N.
H
Hauke Mehrtens 已提交
700 701 702

config USB_HCD_SSB
	tristate "SSB usb host driver"
703
	depends on SSB
H
Hauke Mehrtens 已提交
704 705 706
	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
	select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
	help
707
	  Enable support for the EHCI and OCHI host controller on an bcma bus.
H
Hauke Mehrtens 已提交
708 709 710 711
	  It converts the bcma driver into two platform device drivers
	  for ehci and ohci.

	  If unsure, say N.