USB: ehci_fsl update for MPC831x support

For MPC831x support, change the ehci-fsl driver to preserve
bits set in platform code.  Add a common CONFIG_USB_EHCI_FSL
to indicate presence of Freescale EHCI SOC.  Add FSL_USB2_DR_OTG
operating mode support, thus both host and device can work for the
mini-ab receptacle.  Note: this doesn't enable OTG protocol
support.
Signed-off-by: NLi Yang <leoli@freescale.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/host/Kconfig

@@ -77,6 +77,13 @@ config USB_EHCI_BIG_ENDIAN_DESC
 	depends on USB_EHCI_HCD && 440EPX
 	default y
 
+config USB_EHCI_FSL
+	bool
+	select USB_EHCI_ROOT_HUB_TT
+	default y if MPC834x || PPC_MPC831x
+	---help---
+	  Variation of ARC USB block used in some Freescale chips.
+
 config USB_ISP116X_HCD
 	tristate "ISP116X HCD support"
 	depends on USB

drivers/usb/host/ehci-fsl.c

@@ -67,7 +67,8 @@ int usb_hcd_fsl_probe(const struct hc_driver *driver,
 	 * in host mode.
 	 */
 	if (!((pdata->operating_mode == FSL_USB2_DR_HOST) ||
-	      (pdata->operating_mode == FSL_USB2_MPH_HOST))) {
+	      (pdata->operating_mode == FSL_USB2_MPH_HOST) ||
+	      (pdata->operating_mode == FSL_USB2_DR_OTG))) {
 		dev_err(&pdev->dev,
 			"Non Host Mode configured for %s. Wrong driver linked.\n",
 			pdev->dev.bus_id);
@@ -185,12 +186,14 @@ static void mpc83xx_usb_setup(struct usb_hcd *hcd)
 	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
 	struct fsl_usb2_platform_data *pdata;
 	void __iomem *non_ehci = hcd->regs;
+	u32 temp;
 
 	pdata =
 	    (struct fsl_usb2_platform_data *)hcd->self.controller->
 	    platform_data;
 	/* Enable PHY interface in the control reg. */
-	out_be32(non_ehci + FSL_SOC_USB_CTRL, 0x00000004);
+	temp = in_be32(non_ehci + FSL_SOC_USB_CTRL);
+	out_be32(non_ehci + FSL_SOC_USB_CTRL, temp | 0x00000004);
 	out_be32(non_ehci + FSL_SOC_USB_SNOOP1, 0x0000001b);
 
 #if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
@@ -206,7 +209,8 @@ static void mpc83xx_usb_setup(struct usb_hcd *hcd)
 	out_be32(non_ehci + FSL_SOC_USB_SNOOP2, 0x80000000 | SNOOP_SIZE_2GB);
 #endif
 
-	if (pdata->operating_mode == FSL_USB2_DR_HOST)
+	if ((pdata->operating_mode == FSL_USB2_DR_HOST) ||
+			(pdata->operating_mode == FSL_USB2_DR_OTG))
 		mpc83xx_setup_phy(ehci, pdata->phy_mode, 0);
 
 	if (pdata->operating_mode == FSL_USB2_MPH_HOST) {

drivers/usb/host/ehci-hcd.c

@@ -994,7 +994,7 @@ MODULE_LICENSE ("GPL");
 #define	PCI_DRIVER		ehci_pci_driver
 #endif
 
-#ifdef CONFIG_MPC834x
+#ifdef CONFIG_USB_EHCI_FSL
 #include "ehci-fsl.c"
 #define	PLATFORM_DRIVER		ehci_fsl_driver
 #endif