Kconfig 24.1 KB
Newer Older
1
#
2
# GPIO infrastructure and drivers
3 4
#

5 6 7 8 9 10 11 12
config ARCH_HAVE_CUSTOM_GPIO_H
	bool
	help
	  Selecting this config option from the architecture Kconfig allows
	  the architecture to provide a custom asm/gpio.h implementation
	  overriding the default implementations.  New uses of this are
	  strongly discouraged.

M
Michael Buesch 已提交
13
config ARCH_WANT_OPTIONAL_GPIOLIB
14
	bool
M
Michael Buesch 已提交
15 16 17 18 19 20 21 22 23 24 25
	help
	  Select this config option from the architecture Kconfig, if
	  it is possible to use gpiolib on the architecture, but let the
	  user decide whether to actually build it or not.
	  Select this instead of ARCH_REQUIRE_GPIOLIB, if your architecture does
	  not depend on GPIOs being available, but rather let the user
	  decide whether he needs it or not.

config ARCH_REQUIRE_GPIOLIB
	bool
	select GPIOLIB
26 27 28 29
	help
	  Platforms select gpiolib if they use this infrastructure
	  for all their GPIOs, usually starting with ones integrated
	  into SOC processors.
M
Michael Buesch 已提交
30 31 32 33 34 35 36 37 38 39
	  Selecting this from the architecture code will cause the gpiolib
	  code to always get built in.


menuconfig GPIOLIB
	bool "GPIO Support"
	depends on ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB
	help
	  This enables GPIO support through the generic GPIO library.
	  You only need to enable this, if you also want to enable
40
	  one or more of the GPIO drivers below.
M
Michael Buesch 已提交
41 42

	  If unsure, say N.
43

M
Michael Buesch 已提交
44
if GPIOLIB
45

46 47 48 49
config GPIO_DEVRES
	def_bool y
	depends on HAS_IOMEM

50 51
config OF_GPIO
	def_bool y
D
David S. Miller 已提交
52
	depends on OF
53

M
Mathias Nyman 已提交
54 55 56 57
config GPIO_ACPI
	def_bool y
	depends on ACPI

58 59 60 61 62
config DEBUG_GPIO
	bool "Debug GPIO calls"
	depends on DEBUG_KERNEL
	help
	  Say Y here to add some extra checks and diagnostics to GPIO calls.
63 64 65
	  These checks help ensure that GPIOs have been properly initialized
	  before they are used, and that sleeping calls are not made from
	  non-sleeping contexts.  They can make bitbanged serial protocols
66 67 68
	  slower.  The diagnostics help catch the type of setup errors
	  that are most common when setting up new platforms or boards.

D
David Brownell 已提交
69 70
config GPIO_SYSFS
	bool "/sys/class/gpio/... (sysfs interface)"
71
	depends on SYSFS
D
David Brownell 已提交
72 73 74 75 76 77 78 79 80 81 82 83
	help
	  Say Y here to add a sysfs interface for GPIOs.

	  This is mostly useful to work around omissions in a system's
	  kernel support.  Those are common in custom and semicustom
	  hardware assembled using standard kernels with a minimum of
	  custom patches.  In those cases, userspace code may import
	  a given GPIO from the kernel, if no kernel driver requested it.

	  Kernel drivers may also request that a particular GPIO be
	  exported to userspace; this can be useful when debugging.

G
Grant Likely 已提交
84 85 86
config GPIO_GENERIC
	tristate

87
# put drivers in the right section, in alphabetical order
88

A
ashishj3 已提交
89 90
config GPIO_DA9052
	tristate "Dialog DA9052 GPIO"
91
	depends on PMIC_DA9052
A
ashishj3 已提交
92 93 94
	help
	  Say yes here to enable the GPIO driver for the DA9052 chip.

A
Ashish Jangam 已提交
95 96 97 98 99 100 101 102 103 104 105
config GPIO_DA9055
	tristate "Dialog Semiconductor DA9055 GPIO"
	depends on MFD_DA9055
	help
	  Say yes here to enable the GPIO driver for the DA9055 chip.

	  The Dialog DA9055 PMIC chip has 3 GPIO pins that can be
	  be controller by this driver.

	  If driver is built as a module it will be called gpio-da9055.

106 107 108
config GPIO_MAX730X
	tristate

109
comment "Memory mapped GPIO drivers:"
110

111
config GPIO_CLPS711X
112
	tristate "CLPS711X GPIO support"
113
	depends on ARCH_CLPS711X || COMPILE_TEST
114 115 116
	select GPIO_GENERIC
	help
	  Say yes here to support GPIO on CLPS711X SoCs.
117

118 119 120 121 122 123 124
config GPIO_DAVINCI
	bool "TI Davinci/Keystone GPIO support"
	default y if ARCH_DAVINCI
	depends on ARM && (ARCH_DAVINCI || ARCH_KEYSTONE)
	help
	  Say yes here to enable GPIO support for TI Davinci/Keystone SoCs.

G
Grant Likely 已提交
125 126 127
config GPIO_GENERIC_PLATFORM
	tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
	select GPIO_GENERIC
128
	help
G
Grant Likely 已提交
129
	  Say yes here to support basic platform_device memory-mapped GPIO controllers.
130

131 132 133 134
config GPIO_DWAPB
	tristate "Synopsys DesignWare APB GPIO driver"
	select GPIO_GENERIC
	select GENERIC_IRQ_CHIP
A
Alan Tull 已提交
135
	depends on OF_GPIO
136 137 138 139
	help
	  Say Y or M here to build support for the Synopsys DesignWare APB
	  GPIO block.

140 141
config GPIO_IT8761E
	tristate "IT8761E GPIO support"
142
	depends on X86  # unconditional access to IO space.
143 144 145
	help
	  Say yes here to support GPIO functionality of IT8761E super I/O chip.

M
Magnus Damm 已提交
146 147
config GPIO_EM
	tristate "Emma Mobile GPIO"
148
	depends on ARM && OF_GPIO
M
Magnus Damm 已提交
149 150 151
	help
	  Say yes here to support GPIO on Renesas Emma Mobile SoCs.

152 153 154
config GPIO_EP93XX
	def_bool y
	depends on ARCH_EP93XX
155
	select GPIO_GENERIC
156

157 158
config GPIO_ZEVIO
	bool "LSI ZEVIO SoC memory mapped GPIOs"
159
	depends on ARM && OF_GPIO
160 161 162
	help
	  Say yes here to support the GPIO controller in LSI ZEVIO SoCs.

163 164 165 166 167 168 169 170
config GPIO_MM_LANTIQ
	bool "Lantiq Memory mapped GPIOs"
	depends on LANTIQ && SOC_XWAY
	help
	  This enables support for memory mapped GPIOs on the External Bus Unit
	  (EBU) found on Lantiq SoCs. The gpios are output only as they are
	  created by attaching a 16bit latch to the bus.

171 172 173 174 175 176 177 178 179 180
config GPIO_F7188X
	tristate "F71882FG and F71889F GPIO support"
	depends on X86
	help
	  This option enables support for GPIOs found on Fintek Super-I/O
	  chips F71882FG and F71889F.

	  To compile this driver as a module, choose M here: the module will
	  be called f7188x-gpio.

J
Jonas Jensen 已提交
181 182 183 184 185 186 187
config GPIO_MOXART
	bool "MOXART GPIO support"
	depends on ARCH_MOXART
	help
	  Select this option to enable GPIO driver for
	  MOXA ART SoC devices.

188 189 190 191
config GPIO_MPC5200
	def_bool y
	depends on PPC_MPC52xx

192 193 194 195 196 197 198 199
config GPIO_MPC8XXX
	bool "MPC512x/MPC8xxx GPIO support"
	depends on PPC_MPC512x || PPC_MPC831x || PPC_MPC834x || PPC_MPC837x || \
		   FSL_SOC_BOOKE || PPC_86xx
	help
	  Say Y here if you're going to use hardware that connects to the
	  MPC512x/831x/834x/837x/8572/8610 GPIOs.

200 201
config GPIO_MSM_V1
	tristate "Qualcomm MSM GPIO v1"
202
	depends on GPIOLIB && ARCH_MSM && (ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50)
203 204 205 206 207
	help
	  Say yes here to support the GPIO interface on ARM v6 based
	  Qualcomm MSM chips.  Most of the pins on the MSM can be
	  selected for GPIO, and are controlled by this driver.

208 209
config GPIO_MSM_V2
	tristate "Qualcomm MSM GPIO v2"
210
	depends on GPIOLIB && OF && ARCH_MSM
211 212 213 214 215
	help
	  Say yes here to support the GPIO interface on ARM v7 based
	  Qualcomm MSM chips.  Most of the pins on the MSM can be
	  selected for GPIO, and are controlled by this driver.

216 217
config GPIO_MVEBU
	def_bool y
218
	depends on PLAT_ORION
219
	depends on OF
220 221 222
	select GPIO_GENERIC
	select GENERIC_IRQ_CHIP

223 224 225
config GPIO_MXC
	def_bool y
	depends on ARCH_MXC
G
Grant Likely 已提交
226
	select GPIO_GENERIC
227
	select GENERIC_IRQ_CHIP
G
Grant Likely 已提交
228 229 230 231

config GPIO_MXS
	def_bool y
	depends on ARCH_MXS
232
	select GPIO_GENERIC
233
	select GENERIC_IRQ_CHIP
234

235 236 237 238 239 240 241 242
config GPIO_OCTEON
	tristate "Cavium OCTEON GPIO"
	depends on GPIOLIB && CAVIUM_OCTEON_SOC
	default y
	help
	  Say yes here to support the on-chip GPIO lines on the OCTEON
	  family of SOCs.

243 244
config GPIO_PL061
	bool "PrimeCell PL061 GPIO support"
245
	depends on ARM_AMBA
246
	select IRQ_DOMAIN
247 248 249
	help
	  Say yes here to support the PrimeCell PL061 GPIO device

250 251 252 253 254 255
config GPIO_PXA
	bool "PXA GPIO support"
	depends on ARCH_PXA || ARCH_MMP
	help
	  Say yes here to support the PXA GPIO device

M
Magnus Damm 已提交
256 257 258 259 260 261
config GPIO_RCAR
	tristate "Renesas R-Car GPIO"
	depends on ARM
	help
	  Say yes here to support GPIO on Renesas R-Car SoCs.

262 263 264 265 266 267 268
config GPIO_SAMSUNG
	bool
	depends on PLAT_SAMSUNG
	help
	  Legacy GPIO support. Use only for platforms without support for
	  pinctrl.

269 270 271 272 273 274 275 276 277
config GPIO_SCH311X
	tristate "SMSC SCH311x SuperI/O GPIO"
	help
	  Driver to enable the GPIOs found on SMSC SMSC SCH3112, SCH3114 and
	  SCH3116 "Super I/O" chipsets.

	  To compile this driver as a module, choose M here: the module will
	  be called gpio-sch311x.

278 279 280 281 282 283 284
config GPIO_SPEAR_SPICS
	bool "ST SPEAr13xx SPI Chip Select as GPIO support"
	depends on PLAT_SPEAR
	select GENERIC_IRQ_CHIP
	help
	  Say yes here to support ST SPEAr SPI Chip Select as GPIO device

A
Alessandro Rubini 已提交
285 286 287 288 289 290 291 292
config GPIO_STA2X11
	bool "STA2x11/ConneXt GPIO support"
	depends on MFD_STA2X11
	select GENERIC_IRQ_CHIP
	help
	  Say yes here to support the STA2x11/ConneXt GPIO device.
	  The GPIO module has 128 GPIO pins with alternate functions.

293 294 295 296 297 298
config GPIO_SYSCON
	tristate "GPIO based on SYSCON"
	depends on MFD_SYSCON && OF
	help
	  Say yes here to support GPIO functionality though SYSCON driver.

299 300
config GPIO_TS5500
	tristate "TS-5500 DIO blocks and compatibles"
J
Jean Delvare 已提交
301
	depends on TS5500 || COMPILE_TEST
302 303 304 305 306 307
	help
	  This driver supports Digital I/O exposed by pin blocks found on some
	  Technologic Systems platforms. It includes, but is not limited to, 3
	  blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600
	  LCD port.

308 309 310
config GPIO_TZ1090
	bool "Toumaz Xenif TZ1090 GPIO support"
	depends on SOC_TZ1090
311
	select GENERIC_IRQ_CHIP
312 313 314 315
	default y
	help
	  Say yes here to support Toumaz Xenif TZ1090 GPIOs.

316 317 318 319 320 321 322
config GPIO_TZ1090_PDC
	bool "Toumaz Xenif TZ1090 PDC GPIO support"
	depends on SOC_TZ1090
	default y
	help
	  Say yes here to support Toumaz Xenif TZ1090 PDC GPIOs.

323 324
config GPIO_XILINX
	bool "Xilinx GPIO support"
325
	depends on PPC_OF || MICROBLAZE || ARCH_ZYNQ
326 327 328
	help
	  Say yes here to support the Xilinx FPGA GPIO device

B
Baruch Siach 已提交
329 330 331
config GPIO_XTENSA
	bool "Xtensa GPIO32 support"
	depends on XTENSA
332
	depends on HAVE_XTENSA_GPIO32
B
Baruch Siach 已提交
333 334 335 336 337
	depends on !SMP
	help
	  Say yes here to support the Xtensa internal GPIO32 IMPWIRE (input)
	  and EXPSTATE (output) ports

338 339 340 341 342 343
config GPIO_VR41XX
	tristate "NEC VR4100 series General-purpose I/O Uint support"
	depends on CPU_VR41XX
	help
	  Say yes here to support the NEC VR4100 series General-purpose I/O Uint

344
config GPIO_SCH
345
	tristate "Intel SCH/TunnelCreek/Centerton GPIO"
346
	depends on PCI && X86
347
	select MFD_CORE
348 349
	select LPC_SCH
	help
350 351
	  Say yes here to support GPIO interface on Intel Poulsbo SCH,
	  Intel Tunnel Creek processor or Intel Centerton processor.
352 353 354 355 356 357
	  The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
	  powered by the core power rail and are turned off during sleep
	  modes (S3 and higher). The remaining four GPIOs are powered by
	  the Intel SCH suspend power supply. These GPIOs remain
	  active during S3. The suspend powered GPIOs can be used to wake the
	  system from the Suspend-to-RAM state.
358 359
	  The Intel Tunnel Creek processor has 5 GPIOs powered by the
	  core power rail and 9 from suspend power supply.
360 361 362
	  The Intel Centerton processor has a total of 30 GPIO pins.
	  Twenty-one are powered by the core power rail and 9 from the
	  suspend power supply.
363

364 365 366 367 368 369 370 371 372 373 374 375
config GPIO_ICH
	tristate "Intel ICH GPIO"
	depends on PCI && X86
	select MFD_CORE
	select LPC_ICH
	help
	  Say yes here to support the GPIO functionality of a number of Intel
	  ICH-based chipsets.  Currently supported devices: ICH6, ICH7, ICH8
	  ICH9, ICH10, Series 5/3400 (eg Ibex Peak), Series 6/C200 (eg
	  Cougar Point), NM10 (Tiger Point), and 3100 (Whitmore Lake).

	  If unsure, say N.
376

377 378 379 380 381 382 383 384
config GPIO_IOP
	tristate "Intel IOP GPIO"
	depends on ARM && (ARCH_IOP32X || ARCH_IOP33X)
	help
	  Say yes here to support the GPIO functionality of a number of Intel
	  IOP32X or IOP33X.

	  If unsure, say N.
385

D
Daniel Drake 已提交
386 387
config GPIO_VX855
	tristate "VIA VX855/VX875 GPIO"
388
	depends on PCI
D
Daniel Drake 已提交
389 390 391 392 393 394 395 396 397
	select MFD_CORE
	select MFD_VX855
	help
	  Support access to the VX855/VX875 GPIO lines through the gpio library.

	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

398 399 400 401 402 403 404 405 406 407 408
config GPIO_GE_FPGA
	bool "GE FPGA based GPIO"
	depends on GE_FPGA
	help
	  Support for common GPIO functionality provided on some GE Single Board
	  Computers.

	  This driver provides basic support (configure as input or output, read
	  and write pin state) for GPIO implemented in a number of GE single
	  board computers.

409
config GPIO_LYNXPOINT
410
	tristate "Intel Lynxpoint GPIO support"
411
	depends on ACPI && X86
412 413 414 415 416
	select IRQ_DOMAIN
	help
	  driver for GPIO functionality on Intel Lynxpoint PCH chipset
	  Requires ACPI device enumeration code to set up a platform device.

417 418 419 420 421 422 423 424 425
config GPIO_GRGPIO
	tristate "Aeroflex Gaisler GRGPIO support"
	depends on OF
	select GPIO_GENERIC
	select IRQ_DOMAIN
	help
	  Select this to support Aeroflex Gaisler GRGPIO cores from the GRLIB
	  VHDL IP core library.

C
Christian Ruppert 已提交
426 427
config GPIO_TB10X
	bool
428
	select GENERIC_IRQ_CHIP
C
Christian Ruppert 已提交
429 430
	select OF_GPIO

431 432
comment "I2C GPIO expanders:"

433 434 435 436 437 438
config GPIO_ARIZONA
	tristate "Wolfson Microelectronics Arizona class devices"
	depends on MFD_ARIZONA
	help
	  Support for GPIOs on Wolfson Arizona class devices.

439 440 441 442 443 444 445 446
config GPIO_LP3943
	tristate "TI/National Semiconductor LP3943 GPIO expander"
	depends on MFD_LP3943
	help
	  GPIO driver for LP3943 MFD.
	  LP3943 can be used as a GPIO expander which provides up to 16 GPIOs.
	  Open drain outputs are required for this usage.

447 448 449 450 451
config GPIO_MAX7300
	tristate "Maxim MAX7300 GPIO expander"
	depends on I2C
	select GPIO_MAX730X
	help
452
	  GPIO driver for Maxim MAX7300 I2C-based GPIO expander.
453

E
Eric Miao 已提交
454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472
config GPIO_MAX732X
	tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
	depends on I2C
	help
	  Say yes here to support the MAX7319, MAX7320-7327 series of I2C
	  Port Expanders. Each IO port on these chips has a fixed role of
	  Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
	  Input and Output (designed by 'P'). The combinations are listed
	  below:

	  8 bits:	max7319 (8I), max7320 (8O), max7321 (8P),
		  	max7322 (4I4O), max7323 (4P4O)

	  16 bits:	max7324 (8I8O), max7325 (8P8O),
		  	max7326 (4I12O), max7327 (4P12O)

	  Board setup code must specify the model to use, and the start
	  number for these GPIOs.

473 474
config GPIO_MAX732X_IRQ
	bool "Interrupt controller support for MAX732x"
475
	depends on GPIO_MAX732X=y
476 477 478 479
	help
	  Say yes here to enable the max732x to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

480 481
config GPIO_MC9S08DZ60
	bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
482
	depends on I2C=y && MACH_MX35_3DS
483 484 485
	help
	  Select this to enable the MC9S08DZ60 GPIO driver

486
config GPIO_PCA953X
A
Aaron Sierra 已提交
487
	tristate "PCA95[357]x, PCA9698, TCA64xx, and MAX7310 I/O ports"
488 489
	depends on I2C
	help
490 491 492 493 494 495
	  Say yes here to provide access to several register-oriented
	  SMBus I/O expanders, made mostly by NXP or TI.  Compatible
	  models include:

	  4 bits:	pca9536, pca9537

496
	  8 bits:	max7310, max7315, pca6107, pca9534, pca9538, pca9554,
A
Aaron Sierra 已提交
497
			pca9556, pca9557, pca9574, tca6408, xra1202
498

499 500
	  16 bits:	max7312, max7313, pca9535, pca9539, pca9555, pca9575,
			tca6416
501

502 503
	  24 bits:	tca6424

A
Aaron Sierra 已提交
504
	  40 bits:	pca9505, pca9698
505

506 507 508 509 510 511 512
config GPIO_PCA953X_IRQ
	bool "Interrupt controller support for PCA953x"
	depends on GPIO_PCA953X=y
	help
	  Say yes here to enable the pca953x to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

513
config GPIO_PCF857X
514
	tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
515
	depends on I2C
A
Arnd Bergmann 已提交
516
	select IRQ_DOMAIN
517 518 519 520 521 522 523
	help
	  Say yes here to provide access to most "quasi-bidirectional" I2C
	  GPIO expanders used for additional digital outputs or inputs.
	  Most of these parts are from NXP, though TI is a second source for
	  some of them.  Compatible models include:

	  8 bits:   pcf8574, pcf8574a, pca8574, pca8574a,
524 525
	            pca9670, pca9672, pca9674, pca9674a,
	  	    max7328, max7329
526 527 528 529 530 531 532 533 534 535 536 537

	  16 bits:  pcf8575, pcf8575c, pca8575,
	            pca9671, pca9673, pca9675

	  Your board setup code will need to declare the expanders in
	  use, and assign numbers to the GPIOs they expose.  Those GPIOs
	  can then be used from drivers and other kernel code, just like
	  other GPIOs, but only accessible from task contexts.

	  This driver provides an in-kernel interface to those GPIOs using
	  platform-neutral GPIO calls.

538 539 540 541 542 543 544 545 546
config GPIO_RC5T583
	bool "RICOH RC5T583 GPIO"
	depends on MFD_RC5T583
	help
	  Select this option to enable GPIO driver for the Ricoh RC5T583
	  chip family.
	  This driver provides the support for driving/reading the gpio pins
	  of RC5T583 device through standard gpio library.

547 548 549 550 551 552 553 554 555 556 557
config GPIO_SX150X
	bool "Semtech SX150x I2C GPIO expander"
	depends on I2C=y
	default n
	help
	  Say yes here to provide support for Semtech SX150-series I2C
	  GPIO expanders. Compatible models include:

	  8 bits:  sx1508q
	  16 bits: sx1509q

R
Rabin Vincent 已提交
558 559 560 561 562 563 564
config GPIO_STMPE
	bool "STMPE GPIOs"
	depends on MFD_STMPE
	help
	  This enables support for the GPIOs found on the STMPE I/O
	  Expanders.

565 566 567 568 569 570 571 572 573 574
config GPIO_STP_XWAY
	bool "XWAY STP GPIOs"
	depends on SOC_XWAY
	help
	  This enables support for the Serial To Parallel (STP) unit found on
	  XWAY SoC. The STP allows the SoC to drive a shift registers cascade,
	  that can be up to 24 bit. This peripheral is aimed at driving leds.
	  Some of the gpios/leds can be auto updated by the soc with dsl and
	  phy status.

575 576 577
config GPIO_TC3589X
	bool "TC3589X GPIOs"
	depends on MFD_TC3589X
R
Rabin Vincent 已提交
578
	help
579
	  This enables support for the GPIOs found on the TC3589X
R
Rabin Vincent 已提交
580 581
	  I/O Expander.

582 583 584 585 586 587
config GPIO_TPS65912
	tristate "TI TPS65912 GPIO"
	depends on (MFD_TPS65912_I2C || MFD_TPS65912_SPI)
	help
	  This driver supports TPS65912 gpio chip

D
David Brownell 已提交
588 589 590 591 592 593 594
config GPIO_TWL4030
	tristate "TWL4030, TWL5030, and TPS659x0 GPIOs"
	depends on TWL4030_CORE
	help
	  Say yes here to access the GPIO signals of various multi-function
	  power management chips from Texas Instruments.

595 596 597 598 599 600 601
config GPIO_TWL6040
	tristate "TWL6040 GPO"
	depends on TWL6040_CORE
	help
	  Say yes here to access the GPO signals of twl6040
	  audio chip from Texas Instruments.

M
Mark Brown 已提交
602 603 604 605 606 607 608
config GPIO_WM831X
	tristate "WM831x GPIOs"
	depends on MFD_WM831X
	help
	  Say yes here to access the GPIO signals of WM831x power management
	  chips from Wolfson Microelectronics.

609 610 611 612 613 614 615
config GPIO_WM8350
	tristate "WM8350 GPIOs"
	depends on MFD_WM8350
	help
	  Say yes here to access the GPIO signals of WM8350 power management
	  chips from Wolfson Microelectronics.

M
Mark Brown 已提交
616 617 618 619 620 621 622
config GPIO_WM8994
	tristate "WM8994 GPIOs"
	depends on MFD_WM8994
	help
	  Say yes here to access the GPIO signals of WM8994 audio hub
	  CODECs from Wolfson Microelectronics.

623 624 625 626 627 628 629
config GPIO_ADP5520
	tristate "GPIO Support for ADP5520 PMIC"
	depends on PMIC_ADP5520
	help
	  This option enables support for on-chip GPIO found
	  on Analog Devices ADP5520 PMICs.

630 631 632 633 634 635 636
config GPIO_ADP5588
	tristate "ADP5588 I2C GPIO expander"
	depends on I2C
	help
	  This option enables support for 18 GPIOs found
	  on Analog Devices ADP5588 GPIO Expanders.

637 638 639 640 641 642 643
config GPIO_ADP5588_IRQ
	bool "Interrupt controller support for ADP5588"
	depends on GPIO_ADP5588=y
	help
	  Say yes here to enable the adp5588 to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

644 645
config GPIO_ADNP
	tristate "Avionic Design N-bit GPIO expander"
646
	depends on I2C && OF_GPIO
647 648 649
	help
	  This option enables support for N GPIOs found on Avionic Design
	  I2C GPIO expanders. The register space will be extended by powers
650
	  of two, so the controller will need to accommodate for that. For
651 652 653 654
	  example: if a controller provides 48 pins, 6 registers will be
	  enough to represent all pins, but the driver will assume a
	  register layout for 64 pins (8 registers).

M
Michael Buesch 已提交
655 656
comment "PCI GPIO expanders:"

657 658
config GPIO_CS5535
	tristate "AMD CS5535/CS5536 GPIO support"
659
	depends on MFD_CS5535
660 661 662 663 664 665 666
	help
	  The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
	  can be used for quite a number of things.  The CS5535/6 is found on
	  AMD Geode and Lemote Yeeloong devices.

	  If unsure, say N.

M
Michael Buesch 已提交
667 668 669 670
config GPIO_BT8XX
	tristate "BT8XX GPIO abuser"
	depends on PCI && VIDEO_BT848=n
	help
G
Geert Uytterhoeven 已提交
671
	  The BT8xx frame grabber chip has 24 GPIO pins that can be abused
M
Michael Buesch 已提交
672 673 674 675 676 677 678 679 680 681 682
	  as a cheap PCI GPIO card.

	  This chip can be found on Miro, Hauppauge and STB TV-cards.

	  The card needs to be physically altered for using it as a
	  GPIO card. For more information on how to build a GPIO card
	  from a BT8xx TV card, see the documentation file at
	  Documentation/bt8xxgpio.txt

	  If unsure, say N.

683 684 685 686 687 688 689 690 691 692 693 694
config GPIO_AMD8111
	tristate "AMD 8111 GPIO driver"
	depends on PCI
	help
	  The AMD 8111 south bridge contains 32 GPIO pins which can be used.

	  Note, that usually system firmware/ACPI handles GPIO pins on their
	  own and users might easily break their systems with uncarefull usage
	  of this driver!

	  If unsure, say N

695 696
config GPIO_INTEL_MID
	bool "Intel Mid GPIO support"
697
	depends on PCI && X86
698
	select IRQ_DOMAIN
699
	help
700
	  Say Y here to support Intel Mid GPIO.
701

702
config GPIO_PCH
703
	tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7223/ML7831) GPIO"
704
	depends on PCI && X86
705
	select GENERIC_IRQ_CHIP
706 707 708 709 710
	help
	  This driver is for PCH(Platform controller Hub) GPIO of Intel Topcliff
	  which is an IOH(Input/Output Hub) for x86 embedded processor.
	  This driver can access PCH GPIO device.

711 712
	  This driver also can be used for LAPIS Semiconductor IOH(Input/
	  Output Hub), ML7223 and ML7831.
713
	  ML7223 IOH is for MP(Media Phone) use.
714 715 716
	  ML7831 IOH is for general purpose use.
	  ML7223/ML7831 is companion chip for Intel Atom E6xx series.
	  ML7223/ML7831 is completely compatible for Intel EG20T PCH.
717

718 719 720
config GPIO_ML_IOH
	tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
	depends on PCI
721
	select GENERIC_IRQ_CHIP
722 723 724 725 726 727
	help
	  ML7213 is companion chip for Intel Atom E6xx series.
	  This driver can be used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output
	  Hub) which is for IVI(In-Vehicle Infotainment) use.
	  This driver can access the IOH's GPIO device.

728 729
config GPIO_SODAVILLE
	bool "Intel Sodaville GPIO support"
730
	depends on X86 && PCI && OF
731 732 733 734 735
	select GPIO_GENERIC
	select GENERIC_IRQ_CHIP
	help
	  Say Y here to support Intel Sodaville GPIO.

736 737
config GPIO_TIMBERDALE
	bool "Support for timberdale GPIO IP"
738
	depends on MFD_TIMBERDALE && HAS_IOMEM
739 740 741
	---help---
	Add support for the GPIO IP in the timberdale FPGA.

742 743
config GPIO_RDC321X
	tristate "RDC R-321x GPIO support"
744
	depends on PCI
745
	select MFD_CORE
746 747 748 749 750
	select MFD_RDC321X
	help
	  Support for the RDC R321x SoC GPIOs over southbridge
	  PCI configuration space.

751 752
comment "SPI GPIO expanders:"

753 754 755
config GPIO_MAX7301
	tristate "Maxim MAX7301 GPIO expander"
	depends on SPI_MASTER
756
	select GPIO_MAX730X
757
	help
758
	  GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
759

760
config GPIO_MCP23S08
P
Peter Korsgaard 已提交
761
	tristate "Microchip MCP23xxx I/O expander"
762
	depends on OF_GPIO
763
	depends on (SPI_MASTER && !I2C) || I2C
764
	help
P
Peter Korsgaard 已提交
765 766
	  SPI/I2C driver for Microchip MCP23S08/MCP23S17/MCP23008/MCP23017
	  I/O expanders.
767
	  This provides a GPIO interface supporting inputs and outputs.
768
	  The I2C versions of the chips can be used as interrupt-controller.
769

R
Richard Röjfors 已提交
770 771 772 773 774 775 776
config GPIO_MC33880
	tristate "Freescale MC33880 high-side/low-side switch"
	depends on SPI_MASTER
	help
	  SPI driver for Freescale MC33880 high-side/low-side switch.
	  This provides GPIO interface supporting inputs and outputs.

777 778
config GPIO_74X164
	tristate "74x164 serial-in/parallel-out 8-bits shift register"
779
	depends on SPI_MASTER && OF
780
	help
781 782
	  Driver for 74x164 compatible serial-in/parallel-out 8-outputs
	  shift registers. This driver can be used to provide access
783 784
	  to more gpio outputs.

785 786 787
comment "AC97 GPIO expanders:"

config GPIO_UCB1400
788
	tristate "Philips UCB1400 GPIO"
789 790 791 792 793
	depends on UCB1400_CORE
	help
	  This enables support for the Philips UCB1400 GPIO pins.
	  The UCB1400 is an AC97 audio codec.

G
Guenter Roeck 已提交
794 795 796 797 798 799 800 801 802 803 804 805
comment "LPC GPIO expanders:"

config GPIO_KEMPLD
	tristate "Kontron ETX / COMexpress GPIO"
	depends on MFD_KEMPLD
	help
	  This enables support for the PLD GPIO interface on some Kontron ETX
	  and COMexpress (ETXexpress) modules.

	  This driver can also be built as a module. If so, the module will be
	  called gpio-kempld.

806 807 808 809 810 811 812 813 814 815
comment "MODULbus GPIO expanders:"

config GPIO_JANZ_TTL
	tristate "Janz VMOD-TTL Digital IO Module"
	depends on MFD_JANZ_CMODIO
	help
	  This enables support for the Janz VMOD-TTL Digital IO module.
	  This driver provides support for driving the pins in output
	  mode only. Input mode is not supported.

816 817 818 819 820 821 822
config GPIO_PALMAS
	bool "TI PALMAS series PMICs GPIO"
	depends on MFD_PALMAS
	help
	  Select this option to enable GPIO driver for the TI PALMAS
	  series chip family.

823 824 825 826 827 828 829
config GPIO_TPS6586X
	bool "TPS6586X GPIO"
	depends on MFD_TPS6586X
	help
	  Select this option to enable GPIO driver for the TPS6586X
	  chip family.

830 831 832 833 834 835
config GPIO_TPS65910
	bool "TPS65910 GPIO"
	depends on MFD_TPS65910
	help
	  Select this option to enable GPIO driver for the TPS65910
	  chip family.
M
Mathias Nyman 已提交
836 837 838 839 840 841 842 843

config GPIO_MSIC
	bool "Intel MSIC mixed signal gpio support"
	depends on MFD_INTEL_MSIC
	help
	  Enable support for GPIO on intel MSIC controllers found in
	  intel MID devices

M
Markus Mayer 已提交
844 845 846 847 848 849
config GPIO_BCM_KONA
	bool "Broadcom Kona GPIO"
	depends on OF_GPIO
	help
	  Turn on GPIO support for Broadcom "Kona" chips.

L
Lars Poeschel 已提交
850 851 852 853 854 855 856 857 858 859 860 861 862
comment "USB GPIO expanders:"

config GPIO_VIPERBOARD
	tristate "Viperboard GPIO a & b support"
	depends on MFD_VIPERBOARD && USB
	help
	  Say yes here to access the GPIO signals of Nano River
	  Technologies Viperboard. There are two GPIO chips on the
	  board: gpioa and gpiob.
          See viperboard API specification and Nano
          River Tech's viperboard.h for detailed meaning
          of the module parameters.

M
Michael Buesch 已提交
863
endif