Kconfig

#
# GPIO infrastructure and drivers
#

config ARCH_WANT_OPTIONAL_GPIOLIB
	bool
	help
	  Select this config option from the architecture Kconfig, if
	  it is possible to use gpiolib on the architecture, but let the
	  user decide whether to actually build it or not.
	  Select this instead of ARCH_REQUIRE_GPIOLIB, if your architecture does
	  not depend on GPIOs being available, but rather let the user
	  decide whether he needs it or not.

config ARCH_REQUIRE_GPIOLIB
	bool
	select GPIOLIB
	help
	  Platforms select gpiolib if they use this infrastructure
	  for all their GPIOs, usually starting with ones integrated
	  into SOC processors.
	  Selecting this from the architecture code will cause the gpiolib
	  code to always get built in.



menuconfig GPIOLIB
	bool "GPIO Support"
	depends on ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB
	select GENERIC_GPIO
	help
	  This enables GPIO support through the generic GPIO library.
	  You only need to enable this, if you also want to enable
	  one or more of the GPIO drivers below.

	  If unsure, say N.

if GPIOLIB

config DEBUG_GPIO
	bool "Debug GPIO calls"
	depends on DEBUG_KERNEL
	help
	  Say Y here to add some extra checks and diagnostics to GPIO calls.
	  These checks help ensure that GPIOs have been properly initialized
	  before they are used, and that sleeping calls are not made from
	  non-sleeping contexts.  They can make bitbanged serial protocols
	  slower.  The diagnostics help catch the type of setup errors
	  that are most common when setting up new platforms or boards.

config GPIO_SYSFS
	bool "/sys/class/gpio/... (sysfs interface)"
	depends on SYSFS && EXPERIMENTAL
	help
	  Say Y here to add a sysfs interface for GPIOs.

	  This is mostly useful to work around omissions in a system's
	  kernel support.  Those are common in custom and semicustom
	  hardware assembled using standard kernels with a minimum of
	  custom patches.  In those cases, userspace code may import
	  a given GPIO from the kernel, if no kernel driver requested it.

	  Kernel drivers may also request that a particular GPIO be
	  exported to userspace; this can be useful when debugging.

config GPIO_GENERIC
	tristate

# put drivers in the right section, in alphabetical order

config GPIO_DA9052
	tristate "Dialog DA9052 GPIO"
	depends on PMIC_DA9052
	help
	  Say yes here to enable the GPIO driver for the DA9052 chip.

config GPIO_MAX730X
	tristate

comment "Memory mapped GPIO drivers:"

config GPIO_GENERIC_PLATFORM
	tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
	select GPIO_GENERIC
	help
	  Say yes here to support basic platform_device memory-mapped GPIO controllers.

config GPIO_IT8761E
	tristate "IT8761E GPIO support"
	help
	  Say yes here to support GPIO functionality of IT8761E super I/O chip.

config GPIO_EP93XX
	def_bool y
	depends on ARCH_EP93XX
	select GPIO_GENERIC

config GPIO_EXYNOS4
	def_bool y
	depends on CPU_EXYNOS4210

config GPIO_MXC
	def_bool y
	depends on ARCH_MXC
	select GPIO_GENERIC
	select GENERIC_IRQ_CHIP

config GPIO_MXS
	def_bool y
	depends on ARCH_MXS
	select GPIO_GENERIC
	select GENERIC_IRQ_CHIP

config GPIO_PLAT_SAMSUNG
	def_bool y
	depends on SAMSUNG_GPIOLIB_4BIT

config GPIO_S5PC100
	def_bool y
	depends on CPU_S5PC100

config GPIO_S5PV210
	def_bool y
	depends on CPU_S5PV210

config GPIO_PL061
	bool "PrimeCell PL061 GPIO support"
	depends on ARM_AMBA
	help
	  Say yes here to support the PrimeCell PL061 GPIO device

config GPIO_XILINX
	bool "Xilinx GPIO support"
	depends on PPC_OF || MICROBLAZE
	help
	  Say yes here to support the Xilinx FPGA GPIO device

config GPIO_VR41XX
	tristate "NEC VR4100 series General-purpose I/O Uint support"
	depends on CPU_VR41XX
	help
	  Say yes here to support the NEC VR4100 series General-purpose I/O Uint

config GPIO_SCH
	tristate "Intel SCH/TunnelCreek GPIO"
	depends on PCI && X86
	select MFD_CORE
	select LPC_SCH
	help
	  Say yes here to support GPIO interface on Intel Poulsbo SCH
	  or Intel Tunnel Creek processor.
	  The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
	  powered by the core power rail and are turned off during sleep
	  modes (S3 and higher). The remaining four GPIOs are powered by
	  the Intel SCH suspend power supply. These GPIOs remain
	  active during S3. The suspend powered GPIOs can be used to wake the
	  system from the Suspend-to-RAM state.
	  The Intel Tunnel Creek processor has 5 GPIOs powered by the
	  core power rail and 9 from suspend power supply.

config GPIO_VX855
	tristate "VIA VX855/VX875 GPIO"
	depends on MFD_SUPPORT && PCI
	select MFD_CORE
	select MFD_VX855
	help
	  Support access to the VX855/VX875 GPIO lines through the gpio library.

	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

comment "I2C GPIO expanders:"

config GPIO_MAX7300
	tristate "Maxim MAX7300 GPIO expander"
	depends on I2C
	select GPIO_MAX730X
	help
	  GPIO driver for Maxim MAX7301 I2C-based GPIO expander.

config GPIO_MAX732X
	tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
	depends on I2C
	help
	  Say yes here to support the MAX7319, MAX7320-7327 series of I2C
	  Port Expanders. Each IO port on these chips has a fixed role of
	  Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
	  Input and Output (designed by 'P'). The combinations are listed
	  below:

	  8 bits:	max7319 (8I), max7320 (8O), max7321 (8P),
		  	max7322 (4I4O), max7323 (4P4O)

	  16 bits:	max7324 (8I8O), max7325 (8P8O),
		  	max7326 (4I12O), max7327 (4P12O)

	  Board setup code must specify the model to use, and the start
	  number for these GPIOs.

config GPIO_MAX732X_IRQ
	bool "Interrupt controller support for MAX732x"
	depends on GPIO_MAX732X=y && GENERIC_HARDIRQS
	help
	  Say yes here to enable the max732x to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

config GPIO_PCA953X
	tristate "PCA953x, PCA955x, TCA64xx, and MAX7310 I/O ports"
	depends on I2C
	help
	  Say yes here to provide access to several register-oriented
	  SMBus I/O expanders, made mostly by NXP or TI.  Compatible
	  models include:

	  4 bits:	pca9536, pca9537

	  8 bits:	max7310, pca9534, pca9538, pca9554, pca9557,
	  		tca6408

	  16 bits:	pca9535, pca9539, pca9555, tca6416

config GPIO_PCA953X_IRQ
	bool "Interrupt controller support for PCA953x"
	depends on GPIO_PCA953X=y
	help
	  Say yes here to enable the pca953x to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

config GPIO_PCF857X
	tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
	depends on I2C
	help
	  Say yes here to provide access to most "quasi-bidirectional" I2C
	  GPIO expanders used for additional digital outputs or inputs.
	  Most of these parts are from NXP, though TI is a second source for
	  some of them.  Compatible models include:

	  8 bits:   pcf8574, pcf8574a, pca8574, pca8574a,
	            pca9670, pca9672, pca9674, pca9674a,
	  	    max7328, max7329

	  16 bits:  pcf8575, pcf8575c, pca8575,
	            pca9671, pca9673, pca9675

	  Your board setup code will need to declare the expanders in
	  use, and assign numbers to the GPIOs they expose.  Those GPIOs
	  can then be used from drivers and other kernel code, just like
	  other GPIOs, but only accessible from task contexts.

	  This driver provides an in-kernel interface to those GPIOs using
	  platform-neutral GPIO calls.

config GPIO_SX150X
	bool "Semtech SX150x I2C GPIO expander"
	depends on I2C=y
	default n
	help
	  Say yes here to provide support for Semtech SX150-series I2C
	  GPIO expanders. Compatible models include:

	  8 bits:  sx1508q
	  16 bits: sx1509q

config GPIO_STMPE
	bool "STMPE GPIOs"
	depends on MFD_STMPE
	help
	  This enables support for the GPIOs found on the STMPE I/O
	  Expanders.

config GPIO_TC3589X
	bool "TC3589X GPIOs"
	depends on MFD_TC3589X
	help
	  This enables support for the GPIOs found on the TC3589X
	  I/O Expander.

config GPIO_TWL4030
	tristate "TWL4030, TWL5030, and TPS659x0 GPIOs"
	depends on TWL4030_CORE
	help
	  Say yes here to access the GPIO signals of various multi-function
	  power management chips from Texas Instruments.

config GPIO_WM831X
	tristate "WM831x GPIOs"
	depends on MFD_WM831X
	help
	  Say yes here to access the GPIO signals of WM831x power management
	  chips from Wolfson Microelectronics.

config GPIO_WM8350
	tristate "WM8350 GPIOs"
	depends on MFD_WM8350
	help
	  Say yes here to access the GPIO signals of WM8350 power management
	  chips from Wolfson Microelectronics.

config GPIO_WM8994
	tristate "WM8994 GPIOs"
	depends on MFD_WM8994
	help
	  Say yes here to access the GPIO signals of WM8994 audio hub
	  CODECs from Wolfson Microelectronics.

config GPIO_ADP5520
	tristate "GPIO Support for ADP5520 PMIC"
	depends on PMIC_ADP5520
	help
	  This option enables support for on-chip GPIO found
	  on Analog Devices ADP5520 PMICs.

config GPIO_ADP5588
	tristate "ADP5588 I2C GPIO expander"
	depends on I2C
	help
	  This option enables support for 18 GPIOs found
	  on Analog Devices ADP5588 GPIO Expanders.

config GPIO_ADP5588_IRQ
	bool "Interrupt controller support for ADP5588"
	depends on GPIO_ADP5588=y
	help
	  Say yes here to enable the adp5588 to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

comment "PCI GPIO expanders:"

config GPIO_CS5535
	tristate "AMD CS5535/CS5536 GPIO support"
	depends on PCI && X86 && !CS5535_GPIO && MFD_CS5535
	help
	  The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
	  can be used for quite a number of things.  The CS5535/6 is found on
	  AMD Geode and Lemote Yeeloong devices.

	  If unsure, say N.

config GPIO_BT8XX
	tristate "BT8XX GPIO abuser"
	depends on PCI && VIDEO_BT848=n
	help
	  The BT8xx frame grabber chip has 24 GPIO pins than can be abused
	  as a cheap PCI GPIO card.

	  This chip can be found on Miro, Hauppauge and STB TV-cards.

	  The card needs to be physically altered for using it as a
	  GPIO card. For more information on how to build a GPIO card
	  from a BT8xx TV card, see the documentation file at
	  Documentation/bt8xxgpio.txt

	  If unsure, say N.

config GPIO_LANGWELL
	bool "Intel Langwell/Penwell GPIO support"
	depends on PCI && X86
	help
	  Say Y here to support Intel Langwell/Penwell GPIO.

config GPIO_PCH
	tristate "Intel EG20T PCH / OKI SEMICONDUCTOR ML7223 IOH GPIO"
	depends on PCI && X86
	help
	  This driver is for PCH(Platform controller Hub) GPIO of Intel Topcliff
	  which is an IOH(Input/Output Hub) for x86 embedded processor.
	  This driver can access PCH GPIO device.

	  This driver also can be used for OKI SEMICONDUCTOR IOH(Input/
	  Output Hub), ML7223.
	  ML7223 IOH is for MP(Media Phone) use.
	  ML7223 is companion chip for Intel Atom E6xx series.
	  ML7223 is completely compatible for Intel EG20T PCH.

config GPIO_ML_IOH
	tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
	depends on PCI
	help
	  ML7213 is companion chip for Intel Atom E6xx series.
	  This driver can be used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output
	  Hub) which is for IVI(In-Vehicle Infotainment) use.
	  This driver can access the IOH's GPIO device.

config GPIO_TIMBERDALE
	bool "Support for timberdale GPIO IP"
	depends on MFD_TIMBERDALE && HAS_IOMEM
	---help---
	Add support for the GPIO IP in the timberdale FPGA.

config GPIO_RDC321X
	tristate "RDC R-321x GPIO support"
	depends on PCI
	select MFD_SUPPORT
	select MFD_CORE
	select MFD_RDC321X
	help
	  Support for the RDC R321x SoC GPIOs over southbridge
	  PCI configuration space.

comment "SPI GPIO expanders:"

config GPIO_MAX7301
	tristate "Maxim MAX7301 GPIO expander"
	depends on SPI_MASTER
	select GPIO_MAX730X
	help
	  GPIO driver for Maxim MAX7301 SPI-based GPIO expander.

config GPIO_MCP23S08
	tristate "Microchip MCP23Sxx I/O expander"
	depends on SPI_MASTER
	help
	  SPI driver for Microchip MCP23S08/MPC23S17 I/O expanders.
	  This provides a GPIO interface supporting inputs and outputs.

config GPIO_MC33880
	tristate "Freescale MC33880 high-side/low-side switch"
	depends on SPI_MASTER
	help
	  SPI driver for Freescale MC33880 high-side/low-side switch.
	  This provides GPIO interface supporting inputs and outputs.

config GPIO_74X164
	tristate "74x164 serial-in/parallel-out 8-bits shift register"
	depends on SPI_MASTER
	help
	  Platform driver for 74x164 compatible serial-in/parallel-out
	  8-outputs shift registers. This driver can be used to provide access
	  to more gpio outputs.

comment "AC97 GPIO expanders:"

config GPIO_UCB1400
	bool "Philips UCB1400 GPIO"
	depends on UCB1400_CORE
	help
	  This enables support for the Philips UCB1400 GPIO pins.
	  The UCB1400 is an AC97 audio codec.

comment "MODULbus GPIO expanders:"

config GPIO_JANZ_TTL
	tristate "Janz VMOD-TTL Digital IO Module"
	depends on MFD_JANZ_CMODIO
	help
	  This enables support for the Janz VMOD-TTL Digital IO module.
	  This driver provides support for driving the pins in output
	  mode only. Input mode is not supported.

config GPIO_AB8500
	bool "ST-Ericsson AB8500 Mixed Signal Circuit gpio functions"
	depends on AB8500_CORE && BROKEN
	help
	  Select this to enable the AB8500 IC GPIO driver

config GPIO_TPS65910
	bool "TPS65910 GPIO"
	depends on MFD_TPS65910
	help
	  Select this option to enable GPIO driver for the TPS65910
	  chip family.
endif