提交 5238f7bc 编写于 作者: J John Crispin 提交者: Ralf Baechle

GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder

Move the 2 drivers from arch/mips/lantiq/xway/ to the subsystem and make them
buildable.

The following 2 patches will convert the drivers to OF.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3838/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
上级 57c8cb8f
obj-y := prom.o sysctrl.o clk.o reset.o gpio.o gpio_stp.o gpio_ebu.o dma.o
obj-y := prom.o sysctrl.o clk.o reset.o gpio.o dma.o
......@@ -96,6 +96,14 @@ config GPIO_EP93XX
depends on ARCH_EP93XX
select GPIO_GENERIC
config GPIO_MM_LANTIQ
bool "Lantiq Memory mapped GPIOs"
depends on LANTIQ && SOC_XWAY
help
This enables support for memory mapped GPIOs on the External Bus Unit
(EBU) found on Lantiq SoCs. The gpios are output only as they are
created by attaching a 16bit latch to the bus.
config GPIO_MPC5200
def_bool y
depends on PPC_MPC52xx
......@@ -306,6 +314,16 @@ config GPIO_STMPE
This enables support for the GPIOs found on the STMPE I/O
Expanders.
config GPIO_STP_XWAY
bool "XWAY STP GPIOs"
depends on SOC_XWAY
help
This enables support for the Serial To Parallel (STP) unit found on
XWAY SoC. The STP allows the SoC to drive a shift registers cascade,
that can be up to 24 bit. This peripheral is aimed at driving leds.
Some of the gpios/leds can be auto updated by the soc with dsl and
phy status.
config GPIO_TC3589X
bool "TC3589X GPIOs"
depends on MFD_TC3589X
......
......@@ -30,6 +30,7 @@ obj-$(CONFIG_GPIO_MC33880) += gpio-mc33880.o
obj-$(CONFIG_GPIO_MC9S08DZ60) += gpio-mc9s08dz60.o
obj-$(CONFIG_GPIO_MCP23S08) += gpio-mcp23s08.o
obj-$(CONFIG_GPIO_ML_IOH) += gpio-ml-ioh.o
obj-$(CONFIG_GPIO_MM_LANTIQ) += gpio-mm-lantiq.o
obj-$(CONFIG_GPIO_MPC5200) += gpio-mpc5200.o
obj-$(CONFIG_GPIO_MPC8XXX) += gpio-mpc8xxx.o
obj-$(CONFIG_GPIO_MSM_V1) += gpio-msm-v1.o
......@@ -49,6 +50,7 @@ obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o
obj-$(CONFIG_GPIO_SCH) += gpio-sch.o
obj-$(CONFIG_GPIO_SODAVILLE) += gpio-sodaville.o
obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o
obj-$(CONFIG_GPIO_STP_XWAY) += gpio-stp-xway.o
obj-$(CONFIG_GPIO_SX150X) += gpio-sx150x.o
obj-$(CONFIG_GPIO_TC3589X) += gpio-tc3589x.o
obj-$(CONFIG_ARCH_TEGRA) += gpio-tegra.o
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册