Kconfig 28.9 KB
Newer Older
1
#
2
# GPIO infrastructure and drivers
3 4
#

5 6 7 8 9 10 11 12
config ARCH_HAVE_CUSTOM_GPIO_H
	bool
	help
	  Selecting this config option from the architecture Kconfig allows
	  the architecture to provide a custom asm/gpio.h implementation
	  overriding the default implementations.  New uses of this are
	  strongly discouraged.

M
Michael Buesch 已提交
13
config ARCH_WANT_OPTIONAL_GPIOLIB
14
	bool
M
Michael Buesch 已提交
15 16 17 18 19 20 21 22 23 24 25
	help
	  Select this config option from the architecture Kconfig, if
	  it is possible to use gpiolib on the architecture, but let the
	  user decide whether to actually build it or not.
	  Select this instead of ARCH_REQUIRE_GPIOLIB, if your architecture does
	  not depend on GPIOs being available, but rather let the user
	  decide whether he needs it or not.

config ARCH_REQUIRE_GPIOLIB
	bool
	select GPIOLIB
26 27 28 29
	help
	  Platforms select gpiolib if they use this infrastructure
	  for all their GPIOs, usually starting with ones integrated
	  into SOC processors.
M
Michael Buesch 已提交
30 31 32 33 34 35 36 37 38 39
	  Selecting this from the architecture code will cause the gpiolib
	  code to always get built in.


menuconfig GPIOLIB
	bool "GPIO Support"
	depends on ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB
	help
	  This enables GPIO support through the generic GPIO library.
	  You only need to enable this, if you also want to enable
40
	  one or more of the GPIO drivers below.
M
Michael Buesch 已提交
41 42

	  If unsure, say N.
43

M
Michael Buesch 已提交
44
if GPIOLIB
45

46 47 48 49
config GPIO_DEVRES
	def_bool y
	depends on HAS_IOMEM

50 51
config OF_GPIO
	def_bool y
D
David S. Miller 已提交
52
	depends on OF
53

M
Mathias Nyman 已提交
54 55 56 57
config GPIO_ACPI
	def_bool y
	depends on ACPI

58
config GPIOLIB_IRQCHIP
59
	select IRQ_DOMAIN
60 61
	bool

62 63 64 65 66
config DEBUG_GPIO
	bool "Debug GPIO calls"
	depends on DEBUG_KERNEL
	help
	  Say Y here to add some extra checks and diagnostics to GPIO calls.
67 68 69
	  These checks help ensure that GPIOs have been properly initialized
	  before they are used, and that sleeping calls are not made from
	  non-sleeping contexts.  They can make bitbanged serial protocols
70 71 72
	  slower.  The diagnostics help catch the type of setup errors
	  that are most common when setting up new platforms or boards.

D
David Brownell 已提交
73 74
config GPIO_SYSFS
	bool "/sys/class/gpio/... (sysfs interface)"
75
	depends on SYSFS
D
David Brownell 已提交
76 77 78 79 80 81 82 83 84 85 86 87
	help
	  Say Y here to add a sysfs interface for GPIOs.

	  This is mostly useful to work around omissions in a system's
	  kernel support.  Those are common in custom and semicustom
	  hardware assembled using standard kernels with a minimum of
	  custom patches.  In those cases, userspace code may import
	  a given GPIO from the kernel, if no kernel driver requested it.

	  Kernel drivers may also request that a particular GPIO be
	  exported to userspace; this can be useful when debugging.

G
Grant Likely 已提交
88 89 90
config GPIO_GENERIC
	tristate

91
# put drivers in the right section, in alphabetical order
92

93
# This symbol is selected by both I2C and SPI expanders
94 95 96
config GPIO_MAX730X
	tristate

97
menu "Memory mapped GPIO drivers"
98

99 100 101 102 103 104 105 106 107 108 109 110 111 112
config GPIO_74XX_MMIO
	tristate "GPIO driver for 74xx-ICs with MMIO access"
	depends on OF_GPIO
	select GPIO_GENERIC
	help
	  Say yes here to support GPIO functionality for 74xx-compatible ICs
	  with MMIO access. Compatible models include:
	    1 bit:	741G125 (Input), 741G74 (Output)
	    2 bits:	742G125 (Input), 7474 (Output)
	    4 bits:	74125 (Input), 74175 (Output)
	    6 bits:	74365 (Input), 74174 (Output)
	    8 bits:	74244 (Input), 74273 (Output)
	    16 bits:	741624 (Input), 7416374 (Output)

113 114 115 116 117 118 119 120 121
config GPIO_ALTERA
	tristate "Altera GPIO"
	depends on OF_GPIO
	select GPIOLIB_IRQCHIP
	help
	  Say Y or M here to build support for the Altera PIO device.

	  If driver is built as a module it will be called gpio-altera.

Y
YD Tseng 已提交
122 123 124 125 126 127 128
config GPIO_AMDPT
	tristate "AMD Promontory GPIO support"
	depends on ACPI
	help
	  driver for GPIO functionality on Promontory IOHub
	  Require ACPI ASL code to enumerate as a platform device.

129 130 131 132 133 134
config GPIO_BCM_KONA
	bool "Broadcom Kona GPIO"
	depends on OF_GPIO && (ARCH_BCM_MOBILE || COMPILE_TEST)
	help
	  Turn on GPIO support for Broadcom "Kona" chips.

135 136
config GPIO_BRCMSTB
	tristate "BRCMSTB GPIO support"
137 138
	default y if (ARCH_BRCMSTB || BMIPS_GENERIC)
	depends on OF_GPIO && (ARCH_BRCMSTB || BMIPS_GENERIC || COMPILE_TEST)
139
	select GPIO_GENERIC
140
	select GPIOLIB_IRQCHIP
141 142 143
	help
	  Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs.

144
config GPIO_CLPS711X
145
	tristate "CLPS711X GPIO support"
146
	depends on ARCH_CLPS711X || COMPILE_TEST
147 148 149
	select GPIO_GENERIC
	help
	  Say yes here to support GPIO on CLPS711X SoCs.
150

151 152 153 154 155 156 157
config GPIO_DAVINCI
	bool "TI Davinci/Keystone GPIO support"
	default y if ARCH_DAVINCI
	depends on ARM && (ARCH_DAVINCI || ARCH_KEYSTONE)
	help
	  Say yes here to enable GPIO support for TI Davinci/Keystone SoCs.

158 159 160 161 162 163 164 165
config GPIO_DWAPB
	tristate "Synopsys DesignWare APB GPIO driver"
	select GPIO_GENERIC
	select GENERIC_IRQ_CHIP
	help
	  Say Y or M here to build support for the Synopsys DesignWare APB
	  GPIO block.

M
Magnus Damm 已提交
166 167
config GPIO_EM
	tristate "Emma Mobile GPIO"
168
	depends on ARM && OF_GPIO
M
Magnus Damm 已提交
169 170 171
	help
	  Say yes here to support GPIO on Renesas Emma Mobile SoCs.

172 173 174
config GPIO_EP93XX
	def_bool y
	depends on ARCH_EP93XX
175
	select GPIO_GENERIC
176

R
Rabin Vincent 已提交
177 178 179 180 181
config GPIO_ETRAXFS
	bool "Axis ETRAX FS General I/O"
	depends on CRIS || COMPILE_TEST
	depends on OF
	select GPIO_GENERIC
182
	select GPIOLIB_IRQCHIP
R
Rabin Vincent 已提交
183 184 185
	help
	  Say yes here to support the GPIO controller on Axis ETRAX FS SoCs.

186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240
config GPIO_GE_FPGA
	bool "GE FPGA based GPIO"
	depends on GE_FPGA
	select GPIO_GENERIC
	help
	  Support for common GPIO functionality provided on some GE Single Board
	  Computers.

	  This driver provides basic support (configure as input or output, read
	  and write pin state) for GPIO implemented in a number of GE single
	  board computers.

config GPIO_GENERIC_PLATFORM
	tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
	select GPIO_GENERIC
	help
	  Say yes here to support basic platform_device memory-mapped GPIO controllers.

config GPIO_GRGPIO
	tristate "Aeroflex Gaisler GRGPIO support"
	depends on OF
	select GPIO_GENERIC
	select IRQ_DOMAIN
	help
	  Select this to support Aeroflex Gaisler GRGPIO cores from the GRLIB
	  VHDL IP core library.

config GPIO_ICH
	tristate "Intel ICH GPIO"
	depends on PCI && X86
	select MFD_CORE
	select LPC_ICH
	help
	  Say yes here to support the GPIO functionality of a number of Intel
	  ICH-based chipsets.  Currently supported devices: ICH6, ICH7, ICH8
	  ICH9, ICH10, Series 5/3400 (eg Ibex Peak), Series 6/C200 (eg
	  Cougar Point), NM10 (Tiger Point), and 3100 (Whitmore Lake).

	  If unsure, say N.

config GPIO_IOP
	tristate "Intel IOP GPIO"
	depends on ARM && (ARCH_IOP32X || ARCH_IOP33X)
	help
	  Say yes here to support the GPIO functionality of a number of Intel
	  IOP32X or IOP33X.

	  If unsure, say N.

config GPIO_LOONGSON
	bool "Loongson-2/3 GPIO support"
	depends on CPU_LOONGSON2 || CPU_LOONGSON3
	help
	  driver for GPIO functionality on Loongson-2F/3A/3B processors.

J
Joachim Eastwood 已提交
241 242 243 244 245 246 247 248
config GPIO_LPC18XX
	bool "NXP LPC18XX/43XX GPIO support"
	default y if ARCH_LPC18XX
	depends on OF_GPIO && (ARCH_LPC18XX || COMPILE_TEST)
	help
	  Select this option to enable GPIO driver for
	  NXP LPC18XX/43XX devices.

249 250 251 252 253 254 255 256
config GPIO_LYNXPOINT
	tristate "Intel Lynxpoint GPIO support"
	depends on ACPI && X86
	select GPIOLIB_IRQCHIP
	help
	  driver for GPIO functionality on Intel Lynxpoint PCH chipset
	  Requires ACPI device enumeration code to set up a platform device.

257 258 259 260 261 262
config GPIO_MB86S7X
	bool "GPIO support for Fujitsu MB86S7x Platforms"
	depends on ARCH_MB86S7X
	help
	  Say yes here to support the GPIO controller in Fujitsu MB86S70 SoCs.

263 264 265 266 267 268 269 270
config GPIO_MM_LANTIQ
	bool "Lantiq Memory mapped GPIOs"
	depends on LANTIQ && SOC_XWAY
	help
	  This enables support for memory mapped GPIOs on the External Bus Unit
	  (EBU) found on Lantiq SoCs. The gpios are output only as they are
	  created by attaching a 16bit latch to the bus.

J
Jonas Jensen 已提交
271 272 273
config GPIO_MOXART
	bool "MOXART GPIO support"
	depends on ARCH_MOXART
274
	select GPIO_GENERIC
J
Jonas Jensen 已提交
275 276 277 278
	help
	  Select this option to enable GPIO driver for
	  MOXA ART SoC devices.

279 280 281 282
config GPIO_MPC5200
	def_bool y
	depends on PPC_MPC52xx

283 284 285 286 287 288 289 290
config GPIO_MPC8XXX
	bool "MPC512x/MPC8xxx GPIO support"
	depends on PPC_MPC512x || PPC_MPC831x || PPC_MPC834x || PPC_MPC837x || \
		   FSL_SOC_BOOKE || PPC_86xx
	help
	  Say Y here if you're going to use hardware that connects to the
	  MPC512x/831x/834x/837x/8572/8610 GPIOs.

291 292
config GPIO_MVEBU
	def_bool y
293
	depends on PLAT_ORION
294
	depends on OF
295 296
	select GENERIC_IRQ_CHIP

297 298 299
config GPIO_MXC
	def_bool y
	depends on ARCH_MXC
G
Grant Likely 已提交
300
	select GPIO_GENERIC
301
	select GENERIC_IRQ_CHIP
G
Grant Likely 已提交
302 303 304 305

config GPIO_MXS
	def_bool y
	depends on ARCH_MXS
306
	select GPIO_GENERIC
307
	select GENERIC_IRQ_CHIP
308

309 310 311 312 313 314 315 316
config GPIO_OCTEON
	tristate "Cavium OCTEON GPIO"
	depends on GPIOLIB && CAVIUM_OCTEON_SOC
	default y
	help
	  Say yes here to support the on-chip GPIO lines on the OCTEON
	  family of SOCs.

317
config GPIO_OMAP
318
	tristate "TI OMAP GPIO support" if ARCH_OMAP2PLUS || COMPILE_TEST
319
	default y if ARCH_OMAP
320 321
	depends on ARM
	select GENERIC_IRQ_CHIP
322
	select GPIOLIB_IRQCHIP
323 324 325
	help
	  Say yes here to enable GPIO support for TI OMAP SoCs.

326 327
config GPIO_PL061
	bool "PrimeCell PL061 GPIO support"
328
	depends on ARM_AMBA
329
	select IRQ_DOMAIN
330
	select GPIOLIB_IRQCHIP
331 332 333
	help
	  Say yes here to support the PrimeCell PL061 GPIO device

334 335 336 337 338 339
config GPIO_PXA
	bool "PXA GPIO support"
	depends on ARCH_PXA || ARCH_MMP
	help
	  Say yes here to support the PXA GPIO device

M
Magnus Damm 已提交
340 341
config GPIO_RCAR
	tristate "Renesas R-Car GPIO"
342
	depends on ARCH_SHMOBILE || COMPILE_TEST
343
	select GPIOLIB_IRQCHIP
M
Magnus Damm 已提交
344 345 346
	help
	  Say yes here to support GPIO on Renesas R-Car SoCs.

347 348 349 350 351 352 353
config GPIO_SPEAR_SPICS
	bool "ST SPEAr13xx SPI Chip Select as GPIO support"
	depends on PLAT_SPEAR
	select GENERIC_IRQ_CHIP
	help
	  Say yes here to support ST SPEAr SPI Chip Select as GPIO device

A
Alessandro Rubini 已提交
354 355 356 357 358 359 360 361
config GPIO_STA2X11
	bool "STA2x11/ConneXt GPIO support"
	depends on MFD_STA2X11
	select GENERIC_IRQ_CHIP
	help
	  Say yes here to support the STA2x11/ConneXt GPIO device.
	  The GPIO module has 128 GPIO pins with alternate functions.

362 363 364 365 366 367 368 369 370 371
config GPIO_STP_XWAY
	bool "XWAY STP GPIOs"
	depends on SOC_XWAY
	help
	  This enables support for the Serial To Parallel (STP) unit found on
	  XWAY SoC. The STP allows the SoC to drive a shift registers cascade,
	  that can be up to 24 bit. This peripheral is aimed at driving leds.
	  Some of the gpios/leds can be auto updated by the soc with dsl and
	  phy status.

372 373 374 375 376 377
config GPIO_SYSCON
	tristate "GPIO based on SYSCON"
	depends on MFD_SYSCON && OF
	help
	  Say yes here to support GPIO functionality though SYSCON driver.

378 379 380 381 382
config GPIO_TB10X
	bool
	select GENERIC_IRQ_CHIP
	select OF_GPIO

383 384 385
config GPIO_TZ1090
	bool "Toumaz Xenif TZ1090 GPIO support"
	depends on SOC_TZ1090
386
	select GENERIC_IRQ_CHIP
387 388 389 390
	default y
	help
	  Say yes here to support Toumaz Xenif TZ1090 GPIOs.

391 392 393 394 395 396 397
config GPIO_TZ1090_PDC
	bool "Toumaz Xenif TZ1090 PDC GPIO support"
	depends on SOC_TZ1090
	default y
	help
	  Say yes here to support Toumaz Xenif TZ1090 PDC GPIOs.

398 399 400 401 402 403 404
config GPIO_VF610
	def_bool y
	depends on ARCH_MXC && SOC_VF610
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support Vybrid vf610 GPIOs.

405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422
config GPIO_VR41XX
	tristate "NEC VR4100 series General-purpose I/O Uint support"
	depends on CPU_VR41XX
	help
	  Say yes here to support the NEC VR4100 series General-purpose I/O Uint

config GPIO_VX855
	tristate "VIA VX855/VX875 GPIO"
	depends on PCI
	select MFD_CORE
	select MFD_VX855
	help
	  Support access to the VX855/VX875 GPIO lines through the gpio library.

	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

423 424 425 426 427 428 429 430 431
config GPIO_XGENE
	bool "APM X-Gene GPIO controller support"
	depends on ARM64 && OF_GPIO
	help
	  This driver is to support the GPIO block within the APM X-Gene SoC
	  platform's generic flash controller. The GPIO pins are muxed with
	  the generic flash controller's address and data pins. Say yes
	  here to enable the GFC GPIO functionality.

432 433 434 435 436 437 438 439
config GPIO_XGENE_SB
	tristate "APM X-Gene GPIO standby controller support"
	depends on ARCH_XGENE && OF_GPIO
	select GPIO_GENERIC
	help
	  This driver supports the GPIO block within the APM X-Gene
	  Standby Domain. Say yes here to enable the GPIO functionality.

440
config GPIO_XILINX
441
	tristate "Xilinx GPIO support"
442
	depends on OF_GPIO
443 444 445
	help
	  Say yes here to support the Xilinx FPGA GPIO device

446 447
config GPIO_XLP
	tristate "Netlogic XLP GPIO support"
448
	depends on CPU_XLP && OF_GPIO
449 450 451 452 453 454 455 456
	select GPIOLIB_IRQCHIP
	help
	  This driver provides support for GPIO interface on Netlogic XLP MIPS64
	  SoCs. Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX,
	  XLP9XX and XLP5XX.

	  If unsure, say N.

B
Baruch Siach 已提交
457 458 459
config GPIO_XTENSA
	bool "Xtensa GPIO32 support"
	depends on XTENSA
460
	depends on HAVE_XTENSA_GPIO32
B
Baruch Siach 已提交
461 462 463 464 465
	depends on !SMP
	help
	  Say yes here to support the Xtensa internal GPIO32 IMPWIRE (input)
	  and EXPSTATE (output) ports

466 467 468
config GPIO_ZEVIO
	bool "LSI ZEVIO SoC memory mapped GPIOs"
	depends on ARM && OF_GPIO
469
	help
470
	  Say yes here to support the GPIO controller in LSI ZEVIO SoCs.
471

472 473
config GPIO_ZYNQ
	tristate "Xilinx Zynq GPIO support"
474
	depends on ARCH_ZYNQ || ARCH_ZYNQMP
475
	select GPIOLIB_IRQCHIP
476
	help
477
	  Say yes here to support Xilinx Zynq GPIO controller.
478

L
Linus Walleij 已提交
479 480 481 482 483 484
config GPIO_ZX
	bool "ZTE ZX GPIO support"
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support the GPIO device on ZTE ZX SoCs.

485
endmenu
486

487
menu "Port-mapped I/O GPIO drivers"
488
	depends on X86 # Unconditional I/O space access
489 490 491

config GPIO_104_IDIO_16
	tristate "ACCES 104-IDIO-16 GPIO support"
492
	select GPIOLIB_IRQCHIP
493
	help
494 495 496 497
	  Enables GPIO support for the ACCES 104-IDIO-16 family. The base port
	  address for the device may be set via the idio_16_base module
	  parameter. The interrupt line number for the device may be set via the
	  idio_16_irq module parameter.
498

499 500 501 502 503 504 505 506 507
config GPIO_104_IDI_48
	tristate "ACCES 104-IDI-48 GPIO support"
	select GPIOLIB_IRQCHIP
	help
	  Enables GPIO support for the ACCES 104-IDI-48 family. The base port
	  address for the device may be configured via the idi_48_base module
	  parameter. The interrupt line number for the device may be configured
	  via the idi_48_irq module parameter.

508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529
config GPIO_F7188X
	tristate "F71869, F71869A, F71882FG and F71889F GPIO support"
	help
	  This option enables support for GPIOs found on Fintek Super-I/O
	  chips F71869, F71869A, F71882FG and F71889F.

	  To compile this driver as a module, choose M here: the module will
	  be called f7188x-gpio.

config GPIO_IT87
	tristate "IT87xx GPIO support"
	help
	  Say yes here to support GPIO functionality of IT87xx Super I/O chips.

	  This driver is tested with ITE IT8728 and IT8732 Super I/O chips, and
	  supports the IT8761E Super I/O chip as well.

	  To compile this driver as a module, choose M here: the module will
	  be called gpio_it87

config GPIO_SCH
	tristate "Intel SCH/TunnelCreek/Centerton/Quark X1000 GPIO"
530
	depends on PCI
531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574
	select MFD_CORE
	select LPC_SCH
	help
	  Say yes here to support GPIO interface on Intel Poulsbo SCH,
	  Intel Tunnel Creek processor, Intel Centerton processor or
	  Intel Quark X1000 SoC.

	  The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
	  powered by the core power rail and are turned off during sleep
	  modes (S3 and higher). The remaining four GPIOs are powered by
	  the Intel SCH suspend power supply. These GPIOs remain
	  active during S3. The suspend powered GPIOs can be used to wake the
	  system from the Suspend-to-RAM state.

	  The Intel Tunnel Creek processor has 5 GPIOs powered by the
	  core power rail and 9 from suspend power supply.

	  The Intel Centerton processor has a total of 30 GPIO pins.
	  Twenty-one are powered by the core power rail and 9 from the
	  suspend power supply.

	  The Intel Quark X1000 SoC has 2 GPIOs powered by the core
	  power well and 6 from the suspend power well.

config GPIO_SCH311X
	tristate "SMSC SCH311x SuperI/O GPIO"
	help
	  Driver to enable the GPIOs found on SMSC SMSC SCH3112, SCH3114 and
	  SCH3116 "Super I/O" chipsets.

	  To compile this driver as a module, choose M here: the module will
	  be called gpio-sch311x.

config GPIO_TS5500
	tristate "TS-5500 DIO blocks and compatibles"
	depends on TS5500 || COMPILE_TEST
	help
	  This driver supports Digital I/O exposed by pin blocks found on some
	  Technologic Systems platforms. It includes, but is not limited to, 3
	  blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600
	  LCD port.

endmenu

575 576
menu "I2C GPIO expanders"
	depends on I2C
577

578 579
config GPIO_ADP5588
	tristate "ADP5588 I2C GPIO expander"
580
	help
581 582
	  This option enables support for 18 GPIOs found
	  on Analog Devices ADP5588 GPIO Expanders.
583

584 585 586
config GPIO_ADP5588_IRQ
	bool "Interrupt controller support for ADP5588"
	depends on GPIO_ADP5588=y
587
	help
588 589
	  Say yes here to enable the adp5588 to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.
590

591 592
config GPIO_ADNP
	tristate "Avionic Design N-bit GPIO expander"
593
	depends on OF_GPIO
594 595
	select GPIOLIB_IRQCHIP
	help
596 597 598 599 600 601
	  This option enables support for N GPIOs found on Avionic Design
	  I2C GPIO expanders. The register space will be extended by powers
	  of two, so the controller will need to accommodate for that. For
	  example: if a controller provides 48 pins, 6 registers will be
	  enough to represent all pins, but the driver will assume a
	  register layout for 64 pins (8 registers).
602

603 604 605 606
config GPIO_MAX7300
	tristate "Maxim MAX7300 GPIO expander"
	select GPIO_MAX730X
	help
607
	  GPIO driver for Maxim MAX7300 I2C-based GPIO expander.
608

E
Eric Miao 已提交
609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626
config GPIO_MAX732X
	tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
	help
	  Say yes here to support the MAX7319, MAX7320-7327 series of I2C
	  Port Expanders. Each IO port on these chips has a fixed role of
	  Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
	  Input and Output (designed by 'P'). The combinations are listed
	  below:

	  8 bits:	max7319 (8I), max7320 (8O), max7321 (8P),
		  	max7322 (4I4O), max7323 (4P4O)

	  16 bits:	max7324 (8I8O), max7325 (8P8O),
		  	max7326 (4I12O), max7327 (4P12O)

	  Board setup code must specify the model to use, and the start
	  number for these GPIOs.

627 628
config GPIO_MAX732X_IRQ
	bool "Interrupt controller support for MAX732x"
629
	depends on GPIO_MAX732X=y
630
	select GPIOLIB_IRQCHIP
631 632 633 634
	help
	  Say yes here to enable the max732x to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

635 636
config GPIO_MC9S08DZ60
	bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
637
	depends on I2C=y && MACH_MX35_3DS
638 639 640
	help
	  Select this to enable the MC9S08DZ60 GPIO driver

641
config GPIO_PCA953X
A
Aaron Sierra 已提交
642
	tristate "PCA95[357]x, PCA9698, TCA64xx, and MAX7310 I/O ports"
643
	help
644 645 646 647 648 649
	  Say yes here to provide access to several register-oriented
	  SMBus I/O expanders, made mostly by NXP or TI.  Compatible
	  models include:

	  4 bits:	pca9536, pca9537

650
	  8 bits:	max7310, max7315, pca6107, pca9534, pca9538, pca9554,
A
Aaron Sierra 已提交
651
			pca9556, pca9557, pca9574, tca6408, xra1202
652

653 654
	  16 bits:	max7312, max7313, pca9535, pca9539, pca9555, pca9575,
			tca6416
655

656 657
	  24 bits:	tca6424

A
Aaron Sierra 已提交
658
	  40 bits:	pca9505, pca9698
659

660 661 662
config GPIO_PCA953X_IRQ
	bool "Interrupt controller support for PCA953x"
	depends on GPIO_PCA953X=y
663
	select GPIOLIB_IRQCHIP
664 665 666 667
	help
	  Say yes here to enable the pca953x to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

668
config GPIO_PCF857X
669
	tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
670
	select GPIOLIB_IRQCHIP
A
Arnd Bergmann 已提交
671
	select IRQ_DOMAIN
672 673 674 675 676 677 678
	help
	  Say yes here to provide access to most "quasi-bidirectional" I2C
	  GPIO expanders used for additional digital outputs or inputs.
	  Most of these parts are from NXP, though TI is a second source for
	  some of them.  Compatible models include:

	  8 bits:   pcf8574, pcf8574a, pca8574, pca8574a,
679 680
	            pca9670, pca9672, pca9674, pca9674a,
	  	    max7328, max7329
681 682 683 684 685 686 687 688 689 690 691 692

	  16 bits:  pcf8575, pcf8575c, pca8575,
	            pca9671, pca9673, pca9675

	  Your board setup code will need to declare the expanders in
	  use, and assign numbers to the GPIOs they expose.  Those GPIOs
	  can then be used from drivers and other kernel code, just like
	  other GPIOs, but only accessible from task contexts.

	  This driver provides an in-kernel interface to those GPIOs using
	  platform-neutral GPIO calls.

693 694 695
config GPIO_SX150X
	bool "Semtech SX150x I2C GPIO expander"
	depends on I2C=y
696
	select GPIOLIB_IRQCHIP
697 698 699 700 701 702 703 704
	default n
	help
	  Say yes here to provide support for Semtech SX150-series I2C
	  GPIO expanders. Compatible models include:

	  8 bits:  sx1508q
	  16 bits: sx1509q

705 706 707
endmenu

menu "MFD GPIO expanders"
708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813

config GPIO_ADP5520
	tristate "GPIO Support for ADP5520 PMIC"
	depends on PMIC_ADP5520
	help
	  This option enables support for on-chip GPIO found
	  on Analog Devices ADP5520 PMICs.

config GPIO_ARIZONA
	tristate "Wolfson Microelectronics Arizona class devices"
	depends on MFD_ARIZONA
	help
	  Support for GPIOs on Wolfson Arizona class devices.

config GPIO_CRYSTAL_COVE
	tristate "GPIO support for Crystal Cove PMIC"
	depends on INTEL_SOC_PMIC
	select GPIOLIB_IRQCHIP
	help
	  Support for GPIO pins on Crystal Cove PMIC.

	  Say Yes if you have a Intel SoC based tablet with Crystal Cove PMIC
	  inside.

	  This driver can also be built as a module. If so, the module will be
	  called gpio-crystalcove.

config GPIO_CS5535
	tristate "AMD CS5535/CS5536 GPIO support"
	depends on MFD_CS5535
	help
	  The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
	  can be used for quite a number of things.  The CS5535/6 is found on
	  AMD Geode and Lemote Yeeloong devices.

	  If unsure, say N.

config GPIO_DA9052
	tristate "Dialog DA9052 GPIO"
	depends on PMIC_DA9052
	help
	  Say yes here to enable the GPIO driver for the DA9052 chip.

config GPIO_DA9055
	tristate "Dialog Semiconductor DA9055 GPIO"
	depends on MFD_DA9055
	help
	  Say yes here to enable the GPIO driver for the DA9055 chip.

	  The Dialog DA9055 PMIC chip has 3 GPIO pins that can be
	  be controller by this driver.

	  If driver is built as a module it will be called gpio-da9055.

config GPIO_DLN2
	tristate "Diolan DLN2 GPIO support"
	depends on MFD_DLN2
	select GPIOLIB_IRQCHIP

	help
	  Select this option to enable GPIO driver for the Diolan DLN2
	  board.

	  This driver can also be built as a module. If so, the module
	  will be called gpio-dln2.

config GPIO_JANZ_TTL
	tristate "Janz VMOD-TTL Digital IO Module"
	depends on MFD_JANZ_CMODIO
	help
	  This enables support for the Janz VMOD-TTL Digital IO module.
	  This driver provides support for driving the pins in output
	  mode only. Input mode is not supported.

config GPIO_KEMPLD
	tristate "Kontron ETX / COMexpress GPIO"
	depends on MFD_KEMPLD
	help
	  This enables support for the PLD GPIO interface on some Kontron ETX
	  and COMexpress (ETXexpress) modules.

	  This driver can also be built as a module. If so, the module will be
	  called gpio-kempld.

config GPIO_LP3943
	tristate "TI/National Semiconductor LP3943 GPIO expander"
	depends on MFD_LP3943
	help
	  GPIO driver for LP3943 MFD.
	  LP3943 can be used as a GPIO expander which provides up to 16 GPIOs.
	  Open drain outputs are required for this usage.

config GPIO_MSIC
	bool "Intel MSIC mixed signal gpio support"
	depends on MFD_INTEL_MSIC
	help
	  Enable support for GPIO on intel MSIC controllers found in
	  intel MID devices

config GPIO_PALMAS
	bool "TI PALMAS series PMICs GPIO"
	depends on MFD_PALMAS
	help
	  Select this option to enable GPIO driver for the TI PALMAS
	  series chip family.

814 815 816 817 818 819 820 821 822
config GPIO_RC5T583
	bool "RICOH RC5T583 GPIO"
	depends on MFD_RC5T583
	help
	  Select this option to enable GPIO driver for the Ricoh RC5T583
	  chip family.
	  This driver provides the support for driving/reading the gpio pins
	  of RC5T583 device through standard gpio library.

R
Rabin Vincent 已提交
823 824 825
config GPIO_STMPE
	bool "STMPE GPIOs"
	depends on MFD_STMPE
826
	depends on OF_GPIO
827
	select GPIOLIB_IRQCHIP
R
Rabin Vincent 已提交
828 829 830 831
	help
	  This enables support for the GPIOs found on the STMPE I/O
	  Expanders.

832 833 834
config GPIO_TC3589X
	bool "TC3589X GPIOs"
	depends on MFD_TC3589X
835
	depends on OF_GPIO
836
	select GPIOLIB_IRQCHIP
R
Rabin Vincent 已提交
837
	help
838
	  This enables support for the GPIOs found on the TC3589X
R
Rabin Vincent 已提交
839 840
	  I/O Expander.

841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860
config GPIO_TIMBERDALE
	bool "Support for timberdale GPIO IP"
	depends on MFD_TIMBERDALE
	---help---
	Add support for the GPIO IP in the timberdale FPGA.

config GPIO_TPS6586X
	bool "TPS6586X GPIO"
	depends on MFD_TPS6586X
	help
	  Select this option to enable GPIO driver for the TPS6586X
	  chip family.

config GPIO_TPS65910
	bool "TPS65910 GPIO"
	depends on MFD_TPS65910
	help
	  Select this option to enable GPIO driver for the TPS65910
	  chip family.

861 862 863 864 865 866
config GPIO_TPS65912
	tristate "TI TPS65912 GPIO"
	depends on (MFD_TPS65912_I2C || MFD_TPS65912_SPI)
	help
	  This driver supports TPS65912 gpio chip

D
David Brownell 已提交
867 868 869 870 871 872 873
config GPIO_TWL4030
	tristate "TWL4030, TWL5030, and TPS659x0 GPIOs"
	depends on TWL4030_CORE
	help
	  Say yes here to access the GPIO signals of various multi-function
	  power management chips from Texas Instruments.

874 875 876 877 878 879 880
config GPIO_TWL6040
	tristate "TWL6040 GPO"
	depends on TWL6040_CORE
	help
	  Say yes here to access the GPO signals of twl6040
	  audio chip from Texas Instruments.

881 882 883 884 885 886 887
config GPIO_UCB1400
	tristate "Philips UCB1400 GPIO"
	depends on UCB1400_CORE
	help
	  This enables support for the Philips UCB1400 GPIO pins.
	  The UCB1400 is an AC97 audio codec.

M
Mark Brown 已提交
888 889 890 891 892 893 894
config GPIO_WM831X
	tristate "WM831x GPIOs"
	depends on MFD_WM831X
	help
	  Say yes here to access the GPIO signals of WM831x power management
	  chips from Wolfson Microelectronics.

895 896 897 898 899 900 901
config GPIO_WM8350
	tristate "WM8350 GPIOs"
	depends on MFD_WM8350
	help
	  Say yes here to access the GPIO signals of WM8350 power management
	  chips from Wolfson Microelectronics.

M
Mark Brown 已提交
902 903 904 905 906 907 908
config GPIO_WM8994
	tristate "WM8994 GPIOs"
	depends on MFD_WM8994
	help
	  Say yes here to access the GPIO signals of WM8994 audio hub
	  CODECs from Wolfson Microelectronics.

909
endmenu
910

911 912
menu "PCI GPIO expanders"
	depends on PCI
913

914 915
config GPIO_AMD8111
	tristate "AMD 8111 GPIO driver"
916
	help
917
	  The AMD 8111 south bridge contains 32 GPIO pins which can be used.
M
Michael Buesch 已提交
918

919 920 921
	  Note, that usually system firmware/ACPI handles GPIO pins on their
	  own and users might easily break their systems with uncarefull usage
	  of this driver!
922

923
	  If unsure, say N
924

M
Michael Buesch 已提交
925 926
config GPIO_BT8XX
	tristate "BT8XX GPIO abuser"
927
	depends on VIDEO_BT848=n
M
Michael Buesch 已提交
928
	help
G
Geert Uytterhoeven 已提交
929
	  The BT8xx frame grabber chip has 24 GPIO pins that can be abused
M
Michael Buesch 已提交
930 931 932 933 934 935 936 937 938 939 940
	  as a cheap PCI GPIO card.

	  This chip can be found on Miro, Hauppauge and STB TV-cards.

	  The card needs to be physically altered for using it as a
	  GPIO card. For more information on how to build a GPIO card
	  from a BT8xx TV card, see the documentation file at
	  Documentation/bt8xxgpio.txt

	  If unsure, say N.

941 942
config GPIO_INTEL_MID
	bool "Intel Mid GPIO support"
943
	depends on X86
944
	select GPIOLIB_IRQCHIP
945
	help
946
	  Say Y here to support Intel Mid GPIO.
947

948 949 950 951 952 953 954 955 956
config GPIO_ML_IOH
	tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
	select GENERIC_IRQ_CHIP
	help
	  ML7213 is companion chip for Intel Atom E6xx series.
	  This driver can be used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output
	  Hub) which is for IVI(In-Vehicle Infotainment) use.
	  This driver can access the IOH's GPIO device.

957
config GPIO_PCH
958
	tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7223/ML7831) GPIO"
959
	depends on X86_32 || MIPS || COMPILE_TEST
960
	select GENERIC_IRQ_CHIP
961 962 963 964 965
	help
	  This driver is for PCH(Platform controller Hub) GPIO of Intel Topcliff
	  which is an IOH(Input/Output Hub) for x86 embedded processor.
	  This driver can access PCH GPIO device.

966 967
	  This driver also can be used for LAPIS Semiconductor IOH(Input/
	  Output Hub), ML7223 and ML7831.
968
	  ML7223 IOH is for MP(Media Phone) use.
969 970 971
	  ML7831 IOH is for general purpose use.
	  ML7223/ML7831 is companion chip for Intel Atom E6xx series.
	  ML7223/ML7831 is completely compatible for Intel EG20T PCH.
972

973 974 975 976
config GPIO_RDC321X
	tristate "RDC R-321x GPIO support"
	select MFD_CORE
	select MFD_RDC321X
977
	help
978 979
	  Support for the RDC R321x SoC GPIOs over southbridge
	  PCI configuration space.
980

981 982
config GPIO_SODAVILLE
	bool "Intel Sodaville GPIO support"
983
	depends on X86 && OF
984 985 986 987 988
	select GPIO_GENERIC
	select GENERIC_IRQ_CHIP
	help
	  Say Y here to support Intel Sodaville GPIO.

989
endmenu
990

991 992
menu "SPI GPIO expanders"
	depends on SPI_MASTER
993

994 995
config GPIO_74X164
	tristate "74x164 serial-in/parallel-out 8-bits shift register"
L
Linus Walleij 已提交
996
	depends on OF
997 998 999 1000
	help
	  Driver for 74x164 compatible serial-in/parallel-out 8-outputs
	  shift registers. This driver can be used to provide access
	  to more gpio outputs.
1001

1002 1003
config GPIO_MAX7301
	tristate "Maxim MAX7301 GPIO expander"
1004
	select GPIO_MAX730X
1005
	help
1006
	  GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
1007

R
Richard Röjfors 已提交
1008 1009 1010 1011 1012 1013
config GPIO_MC33880
	tristate "Freescale MC33880 high-side/low-side switch"
	help
	  SPI driver for Freescale MC33880 high-side/low-side switch.
	  This provides GPIO interface supporting inputs and outputs.

L
Linus Walleij 已提交
1014 1015 1016 1017 1018 1019 1020
endmenu

menu "SPI or I2C GPIO expanders"
	depends on (SPI_MASTER && !I2C) || I2C

config GPIO_MCP23S08
	tristate "Microchip MCP23xxx I/O expander"
1021
	help
L
Linus Walleij 已提交
1022 1023 1024 1025
	  SPI/I2C driver for Microchip MCP23S08/MCP23S17/MCP23008/MCP23017
	  I/O expanders.
	  This provides a GPIO interface supporting inputs and outputs.
	  The I2C versions of the chips can be used as interrupt-controller.
1026

1027
endmenu
M
Mathias Nyman 已提交
1028

1029 1030
menu "USB GPIO expanders"
	depends on USB
L
Lars Poeschel 已提交
1031 1032 1033

config GPIO_VIPERBOARD
	tristate "Viperboard GPIO a & b support"
1034
	depends on MFD_VIPERBOARD
L
Lars Poeschel 已提交
1035 1036 1037 1038 1039 1040 1041 1042
	help
	  Say yes here to access the GPIO signals of Nano River
	  Technologies Viperboard. There are two GPIO chips on the
	  board: gpioa and gpiob.
          See viperboard API specification and Nano
          River Tech's viperboard.h for detailed meaning
          of the module parameters.

1043
endmenu
1044

M
Michael Buesch 已提交
1045
endif