Set the SW prio_tc values at initialization to the HW setting.
Setting the SW prio_tc default values to be the HW setting by reading the
rtrup2tc register. For any TC change we need to reset the device.
This will remove the need to reset the device at the first
time we call ixgbe_dcbnl_ieee_setets.
Signed-off-by: NAmir Hanania <amir.hanania@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes unused i2c function definition.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes LED issues with i210 and i211 devices, due to changes in the
device registers.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reorders disabling napi and irqs during igb_down.
This is done to avoid possible panic's found in other Intel drivers
when Rx traffic arrives while interface is going down.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where we were only checking to update checksum
on first part of nvm image.  Newer parts have multiple checksum fields and
checksum function will accommodate that as long as we call it in the first
place for any changes made.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This path allows users to get appropriate flow control setting on SerDes
devices, based on original implementation for Copper devices.
Also, since 100baseFX does not support setting flow control, so exclude
it from the setting mechanism.
Signed-off-by: NAkeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for SFP modules media type discovery for
SGMII, which will enable driver to detect supported external PHYs,
including 100baseFXSFP module.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to support a more accurate check for a PTP Rx hang where the
device can no longer timestamp received packets, we need to update, per
ring, when the last Rx timestamp was. Because of how the PTP Rx hang logic
works, the current logic is valid, but properly updating the ring variable
increases the accuracy of the check.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch addresses the changes needed to make LEDs work properly with
negative logic. This implementation uses LED Invert bit to reverse the
logic issue that occurred when LEDs are driven by cathode. Keep LEDs
blinking for SerDes devices. Also made changes to magic number and the
for loop to reduce number of shifts.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the issue of unlocking swflag_mutex for 82574 and 82583
devices regardless of if the hw semaphore has been successfully acquired via
e1000_get_hw_semaphore_82574(). With this patch, unlocking mutex now depends
on if the hw semaphore was successfully acquired before. And 82574/82583
devices are reset regardless of whether e1000_get_hw_semaphore_82574()
returns success or failure.
Reported-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is currently no way for an Ethernet MAC driver servicing PHY link
interrupts to notify this to the PHY state machine without defining its
own state machine. Since most drivers are not so special, introduce a
helper: phy_mac_interrupt() which can be called from a link up/down
interrupt routine to update the PHY state machine. To avoid code
duplication some refactoring has been done to expose the workqueue and
its corresponding callback internally.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a PHY device is registered with the special IRQ value
PHY_IGNORE_INTERRUPT (-2) it will not properly be handled by the PHY
library:

- it continues to poll its register, while we do not want this
  because such PHY link events or register changes are serviced by an
  Ethernet MAC
- it will still try to configure PHY interrupts at the PHY level, such
  interrupts do not exist at the PHY but at the MAC level
- the state machine only handles PHY_POLL, but should also handle
  PHY_IGNORE_INTERRUPT similarly

This patch updates the PHY state machine and initialization paths to
account for the specific PHY_IGNORE_INTERRUPT. Based on an earlier patch
by Thomas Petazzoni, and reworked to add the missing bits. Add a helper
phy_interrupt_is_valid() which specifically tests for a PHY interrupt
not to be PHY_POLL or PHY_IGNORE_INTERRUPT and use it throughout the
code.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver and Firmware versions updated to 3.2.21.1.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

User should not be allowed to delete base function of eth port. Add a new field
to the bfa ioc attributes structure to indicate if the given ioc is default
function on the port or not.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Failure of the UCAST set for base mac address fails when user configures a
duplicate mac address that matches that of another vNIC on the same port.
The bna does not handle the ucast failure and keeps this address in cache.
On disable of the vNIC, bna tries to delete the failed base mac address and the
fw asserts.

On failure of ucast address, mark ucast address set to false.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver configuration flags are retained across open/stop operations preventing
configurations to be set in next open/stop. Setting MTU on a 1020 causes
network to fail until a reboot is performed on the host.

Clear the flags when configuration resets in hardware.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds Device Tree support to dm9000 driver.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Follow-up on module_free()/vfree() that takes care of the rest, so no
longer this workaround with work_struct needed.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Followup patch on module_free()/vfree() that takes care of the rest, so
no longer this workaround with work_struct is needed.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Matt Evans <matt@ozlabs.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP md5 code uses per cpu variables but protects access to them with
a shared spinlock, which is a contention point.

[ tcp_md5sig_pool_lock is locked twice per incoming packet ]

Makes things much simpler, by allocating crypto structures once, first
time a socket needs md5 keys, and not deallocating them as they are
really small.

Next step would be to allow crypto allocations being done in a NUMA
aware way.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The next pointer within the inet6_dev structure seems not to be used
anywhere. So just remove it. Tested with allmodconfig on x86_64.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A cpu executing the network receive path sheds packets when its input
queue grows to netdev_max_backlog. A single high rate flow (such as a
spoofed source DoS) can exceed a single cpu processing rate and will
degrade throughput of other flows hashed onto the same cpu.

This patch adds a more fine grained hashtable. If the netdev backlog
is above a threshold, IRQ cpus track the ratio of total traffic of
each flow (using 4096 buckets, configurable). The ratio is measured
by counting the number of packets per flow over the last 256 packets
from the source cpu. Any flow that occupies a large fraction of this
(set at 50%) will see packet drop while above the threshold.

Tested:
Setup is a muli-threaded UDP echo server with network rx IRQ on cpu0,
kernel receive (RPS) on cpu0 and application threads on cpus 2--7
each handling 20k req/s. Throughput halves when hit with a 400 kpps
antagonist storm. With this patch applied, antagonist overload is
dropped and the server processes its complete load.

The patch is effective when kernel receive processing is the
bottleneck. The above RPS scenario is a extreme, but the same is
reached with RFS and sufficient kernel processing (iptables, packet
socket tap, ..).
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should correctly free related resources (grant ref, memory page, evtchn)
when setup_netfront fails.
Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the VIA Velocity network driver to be bound to a
OF created platform device.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the pci_* dma functions and replace with the more generic
versions.

In preparation of adding platform support, a new struct device *dev
is added to struct velocity_info which can be used by both the pci
and platform code.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve the clarity of the code in preparation for converting the
dma functions to generic versions, which require a struct device *.

This makes it possible to store a 'struct device *dev' in the
velocity_info structure.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's suboptimal to invoke quite complex VORTEX_PCI() macro every time we want
to get a 'struct pci_dev *' when we already have it in a variable...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These 2 places are the only matches for is_eisa in the whole tree.
Signed-off-by: NRolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x_set_features() forces a driver reload if GRO setting is changed.

A reload makes the ethernet port unresponsive for about 5 seconds.

This is not needed in the common case LRO is enabled, as LRO
(TPA_ENABLE_FLAG) has precedence over GRO (GRO_ENABLE_FLAG)

Tested:
 Verified that "ethtool -K eth0 gro {on|off}" doesn't blackout
 the NIC anymore

Google-Bug-Id: 8440442
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Dmitry Kravkov <dmitry@broadcom.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nithin Nayak Sujir says:

====================
This series adds support for modifying EEE settings via ethtool. Since this can
impact Link Flap Avoidance, the driver pulls the current hardware settings if
LFA is enabled. This is similar to how we do the link settings to avoid a flap.

v2: Fixes pointed out by Ben Hutchings.
 - Use MDIO_AN_EEE_LPABLE to set the lp_advertised field.
 - Check that tx_lpi_timer is within valid range.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reviewed-by: NBen Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eee_config_ok() was checking only for mismatch in advertised settings.
This patch expands the scope of eee_config_ok() to check for mismatch in
the other eee settings. On mismatch we will require a call to
tg3_setup_eee() to push the configured settings to the hardware.
Reviewed-by: NBen Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add tg3_eee_pull_config() to pull the settings from the hardware and
populate the eee structure.

If Link Flap Avoidance is enabled, we pull the eee settings from the hw
so as not to cause a phy reset on eee config mismatch later. This
requires moving down tg3_setup_eee() below the tg3_pull_config() to not
trample existing settings.
Reviewed-by: NBen Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an eee structure and update it with eee settings. This will be used
for set/get_eee operations. Add common function tg3_setup_eee() that
will be used in the subsequent patches.
Reviewed-by: NBen Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not leak starting address of BPF JIT code for non root users,
as it might help intruders to perform an attack.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hpa bringed into my attention some security related issues
with BPF JIT on x86.

This patch makes sure the bpf generated code is marked read only,
as other kernel text sections.

It also splits the unused space (we vmalloc() and only use a fraction of
the page) in two parts, so that the generated bpf code not starts at a
known offset in the page, but a pseudo random one.

Refs:
http://mainisusuallyafunction.blogspot.com/2012/11/attacking-hardened-linux-systems-with.htmlReported-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reviewed-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_timeout_skb() was intended to trigger fast recovery on timeout,
unfortunately in reality it often causes spurious retransmission
storms during fast recovery. The particular sign is a fast retransmit
over the highest sacked sequence (SND.FACK).

Currently the RTO timer re-arming (as in RFC6298) offers a nice cushion
to avoid spurious timeout: when SND.UNA advances the sender re-arms
RTO and extends the timeout by icsk_rto. The sender does not offset
the time elapsed since the packet at SND.UNA was sent.

But if the next (DUP)ACK arrives later than ~RTTVAR and triggers
tcp_fastretrans_alert(), then tcp_timeout_skb() will mark any packet
sent before the icsk_rto interval lost, including one that's above the
highest sacked sequence. Most likely a large part of scorebard will be
marked.

If most packets are not lost then the subsequent DUPACKs with new SACK
blocks will cause the sender to continue to retransmit packets beyond
SND.FACK spuriously. Even if only one packet is lost the sender may
falsely retransmit almost the entire window.

The situation becomes common in the world of bufferbloat: the RTT
continues to grow as the queue builds up but RTTVAR remains small and
close to the minimum 200ms. If a data packet is lost and the DUPACK
triggered by the next data packet is slightly delayed, then a spurious
retransmission storm forms.

As the original comment on tcp_timeout_skb() suggests: the usefulness
of this feature is questionable. It also wastes cycles walking the
sack scoreboard and is actually harmful because of false recovery.

It's time to remove this.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NNandita Dukkipati <nanditad@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>