- 24 3月, 2016 32 次提交
-
-
由 Hans de Goede 提交于
Always select OF_BOARD_SETUP on sunxi, rather then having it in almost all our defconfigs. This also fixes it missing from some recently added defconfigs. This commit also modifies our ft_board_setup() to not cause warnings when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always build it. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 vishnupatekar 提交于
Kconfig default settings are same as mentioned Sinovoip Bpi-m3 schematic. As axp818 ALDO support is enabled, it causes bpi-m3 fail to boot if ALDOs are set to 0. Signed-off-by: NVishnu Patekar <vishnupatekar0510@gmail.com> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Hans de Goede 提交于
This enables the use of the sata connector in u-boot. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
There are 2 reasons for doing this: 1) The main reason for doing this is to move it outside of board/sunxi/ahci.c, so that it can be used on boards which use a usb<->sata chip too; 2) While doing this I realized that doing it from board_init also meant doing it much earlier. Some printf get_timer(0) calls show that the time between board_init() and scsi_init() is more then 600 ms, so we can drop the mdelay(500) While at it also drop the printf("SUNXI SCSI INIT\n") AHCI init is noisy enough by itself. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
cpu_eth_init is no longer called for dm enabled eth drivers, this was causing the sunxi gmac eth controller to no longer work in u-boot. This commit fixes this by calling the clock, reset and pinmux setup function from s_init() and enabling the phy power pin (if any) from board_init(). The enabling of phy power cannot be done from s_init because it uses dm and dm is not ready yet at this point. Note that the mdelay is dropped as the phy gets enabled much earlier now, so it is no longer needed. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk> Tested-by: NKarsten Merker <merker@debian.org> Tested-by: NMichael Haas <haas@computerlinguist.org>
-
由 Hans de Goede 提交于
The 2nd usb controller on sun4i/sun7i has its base address 0x8000 bytes from the 1st one, rather then 0x1000. Also the ahb clk gates are interleaved with the ohci clk-gates introducing a hole between the clks for usb1 and usb2. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
This enables support for the eMMC found on the orangepi plus. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
On some sunxi boards (and presumably also non sunxi boards) u-boot can be either loaded from a sdcard in a micro-sd slot, or from eMMC. Print which MMC spl tries to boot from, to help debugging. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Hans de Goede 提交于
The kernel has different compatible strings for the pio block because the pin-muxing is different on all the different SoCs, but sunxi_gpio.c only support the basic gpio functionality, which is identical everywhere. Add the missing compatible strings for various SoC models. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
This fixes the USB ports not working on the orangepi_plus and stops us from messing with gpio-s which we should not touch on the orangepi_pc. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
The H3 has USB0 - USB3, add support for having a USB vbus pin for USB3. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
Enable building of drivers/net/phy/realtek.c so that realtek phys get properly initialized. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Alex Kaplan 提交于
The CHIP has a composite video output in the mini-Jack connector, alongside with the 2 audio channels. Enable this output in U-Boot. Signed-off-by: NAlex Kaplan <kaplan2539@gmail.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Boris Brezillon 提交于
Unlike the datasheet recommendation, the R8 SoC requires a 1.4V supply for its CPU when operating at 1Ghz. Rely on the default value specified in the Kconfig entry. Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Lawrence Yu 提交于
The behavior before this patch would attempt to configure the mux setting for pins 0 to 27 on PORTD to all be setting 3 for LVDS. The LVDS interface actually only uses pins 18 to 27 and not pins 0 to 27 as in the parallel LCD interface. This patch restricts the configuration to only the relevant pins 18 to 27 on PORTD. This was tested on a sun8i A33 tablet with an LVDS screen. MMC1 has the capability to use pins 2 to 7 on PORTD and the mux on those pins was being inadvertently set to setting 3 for MMC functionality which this patch corrects. Signed-off-by: NLawrence Yu <lyu@micile.com> [hdegoede@redhat.com: Only apply this change to A23 / A33] Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Chen-Yu Tsai 提交于
On the A83T and H3, the SID block is at a different address. Furthurmore, the e-fuses are at an offset of 0x200 within the hardware's address space. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Hans de Goede 提交于
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot, 4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI, a TRRS headphone jack for stereo out and composite out, a microphone, an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header and a 40-pin GPIO header. The added dts file is identical to the one submitted to the upstream kernel. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
The Dserve DSRV9703C is a 9.7" A10 tablet with a 1024x768 ips LCD, 1G RAM, 4GB flash, a Focaltech FT5406EE8 touchscreen and rtl8188ctv wifi. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Peter Korsgaard 提交于
The yones toptech bs1078-v2 is a 10.1" tablet without any clear markings on the outside, but 'YONESTOPTECH-BS1078' written on the PCB silkscreen. It features a 16:9 1024:600 LCD, A31s SoC, 1GB RAM, 8G NAND, silead gsl3675 touchscreen and a RTL8723AS wifi chip: https://linux-sunxi.org/Yones_Toptech_BS1078_V2Signed-off-by: NPeter Korsgaard <peter@korsgaard.com> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Chen-Yu Tsai 提交于
The Sinlinx A31s SDK is a A31s based module/baseboard development kit. The core module has the SoC, PMIC, DRAM, eMMC and supporting components. There are also pads for UART0, JTAG and I2S. The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0 hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume buttons, RS232 style UART and USB OTG (though VBUS is not connected). Various headers are available for other addon modules, such as SDIO WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Stefan Roese 提交于
The ICnova-A20-SWAC is a baseboard, equipped with the ICnova-A20 SoM from In-Circuit: http://wiki.in-circuit.de/index.php5?title=ICnova_A20_SODIMM http://linux-sunxi.org/In-Circuit_ICnova_A20 This patch adds support for this board, including ethernet, LCD and USB support. Signed-off-by: NStefan Roese <sr@denx.de> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Marcus Cooper 提交于
Add defconfig for the multi board device based on the Allwinner A20 SoC. It contains the A20 Itead Core module and a base board for the external interfaces. The core module comes with 4GB NAND and 1GB DDR RAM. The base board to which the core board is connected provides 3 USB 2.0 Host ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet port, HDMI, IR receiver, SPDIF and a 32-pin GPIO header. This header expands the features of core board by exposing the VGA pins, audio In/Out pins, SATA, SPI, I2C, UARTS, USB-OTG and power.. Signed-off-by: NMarcus Cooper <codekipper@gmail.com> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Chen-Yu Tsai 提交于
Cubietruck Plus is a A83T/H8 based development board. The board has standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, WiFi, headphone out / mic in, and various GPIO headers. The board also has an EEPROM on i2c0 which holds the MAC address. DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 is connected to the reset control of the PHY. EMAC is not actually supported yet. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Hans de Goede 提交于
The Polaroid MID2809PXE4 is a 9" tablet which is clearly marked Polaroid MID2809PXE4 on the back. It features a 9" 16:9 800x480 LCD, A23 Soc, 1GB RAM, 8GB NAND, gsl3670 touchscreen and esp8089 wifi. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
The Difrnce dit4350 tablet is a tiny tablet with a 4.3" 16:9 480x272 LCD, A13 SoC, 512M RAM, 4G NAND, solomon systech ssd2532qn6 touchscreen at i2c1 address 0x48, Memsic MXC622X accelerometer at i2c1 address 0x15 and rtl8188etv wifi. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
The colorfly e708 q1 is a 7" tablet which is clearly marked as colorfly e708 q1 on the back. It features a 9:16 800x1280 IPS LCD, A31s SoC, 1GB RAM, 8G NAND, ilitek 2139qt004 touchscreen on i2c-1 addr 0x41, stk8313 accelerometer on i2c-2 addr 0x22 and a rtl8188etv wifi chip. The added dts is identical to the dts submitted to the upstream kernel, note this commit also syncs axp22x.dtsi and sun6i-a31.dtsi with the upstream kernel as the added dts depends on these. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
Fix a copy and paste error which caused us to use the uart rather then the twi reset bits in clock_twi_onoff for sun9i. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
clock_sun8i_a83.c did not contain a clock_twi_onoff implementation at all, this is fixed by moving the clock_sun6i.c implementation, which is correct for the a83 too, to a shared location. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
The clock_sun6i.c implementation was not deasserting the reset for the regular i2c controllers, this commit fixes this. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
Sync dts files with the upstream kernel including changes queued for 4.6: https://git.kernel.org/cgit/linux/kernel/git/mripard/linux.git/commit/?h=sunxi/dt-for-4.6 Note this adds a number of new unused board dts files. I've asked the authors of the kernel commits adding these to submit a matching defconfig to u-boot. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
This commit syncs the dt-bindings/input/* headers with the kernel (v4.5) and adds dt-bindings/clock/sun4i-a10-pll2.h, both are necessary for newer sunxi dts files to build. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Reviewed-by: NTom Rini <trini@konsulko.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
I've had this one a23 tablet which would not boot and I've finally figured out what the problem is by looking at the released boot0 code, it seems the magic sram controller poke which we need to do in s_init() depends on the revision of the a23. Specifically this change is needed to get the A23 SoC I have with the following serial to boot: "E6071AB 26Y7". Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
- 23 3月, 2016 8 次提交
-
-
由 Bin Meng 提交于
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig to use that. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NStephen Warren <swaren@nvidia.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Bin Meng 提交于
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig to use that. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> [trini: Fixup MPC8641HPCN* and r2dplus configs] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Bin Meng 提交于
Some boards' defconfig files are out of order. Clean this up. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Simon Glass 提交于
This should return 0 on success, not 1. Fix it. Signed-off-by: NSimon Glass <sjg@chromium.org> Acked-by: NMarek Vasut <marex@denx.de> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
The error path for fit_import_data() is incorrect if the second open() call fails. Reported-by: Coverity (CID: 138489) Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
The file that is opened is not closed in all cases. Fix it. Reported-by: Coverity (CID: 138490) Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
Make sure that both the error path and normal return free the buffer and close the file. Reported-by: Coverity (CID: 138491) Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
The 'buf' variable is not freed. Fix it. Reported-by: Coverity (CID: 138492) Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-