- 15 2月, 2019 8 次提交
-
-
由 Shubhrajyoti Datta 提交于
Fix the below warning as the core looks for the compatible string. [ 5.198919] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@19 [ 5.207454] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@19 [ 5.216394] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@30 [ 5.224986] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@30 [ 5.233927] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@35 [ 5.242527] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@35 [ 5.263880] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@36 [ 5.272477] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@36 [ 5.281415] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@51 [ 5.290008] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@51 Signed-off-by: NShubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
It will never reach mainline that's why remove it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Amit Kucheria 提交于
The idle-states binding documentation[1] mentions that the 'entry-method' property is required on 64-bit platforms and must be set to "psci". Linux commit a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states bindings examples") attempted to fix this earlier but clearly more is needed. Linux docs: Documentation/devicetree/bindings/arm/idle-states.txt (see idle-states node) Signed-off-by: NAmit Kucheria <amit.kucheria@linaro.org> Acked-by: NSudeep Holla <sudeep.holla@arm.com> Acked-by: NLi Yang <leoyang.li@nxp.com> Signed-off-by: NOlof Johansson <olof@lixom.net> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Trivial fix. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Mounika Grace Akula 提交于
This patch adds reset-on-timeout to FPD WDT which will trigger an interrupt to PMU when watchdog expiry happens and PMU takes the necessary action. If this property is not enabled, reason will not be known when watchdog expiry happens. This patch also modifies the default timeout to 60 seconds. Reason is that if u-boot enables WDT, it will set the timeout to 10 seconds and this is not enough to boot till Linux and start the WDT application in Linux. 60 seconds is the maximum safest value to boot till Linux and start the WDT application. Users need to change this timeout value to fit their needs. Signed-off-by: NMounika Grace Akula <mounika.grace.akula@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Luis Araneda 提交于
Replace the current value of the model property by a more accurate description of each board (which includes the manufacturer), as some of the boards had the same value ("Xilinx Zynq") Signed-off-by: NLuis Araneda <luaraneda@gmail.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Luis Araneda 提交于
Both boards are made by Avnet, Inc. So add an additional value to the compatible property Signed-off-by: NLuis Araneda <luaraneda@gmail.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
mmc name is recommended based on devicetree specification. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 14 2月, 2019 26 次提交
-
-
由 Michal Simek 提交于
All options have been moved to Kconfig and there is no need to have board header files. Mini configurations require them that's why they are still there. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
SPD autodetection hasn't been enabled that's why there is zero size difference if that options are enabled/disabled. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Replace SDHCI controller listing by Kconfig symbol to let SPL know that this board is using multiple SDHCIs controllers. Kconfig help message should explain why this is needed. Origin symbols were used in full u-boot but with moving to distro boot this was fixed already. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
All platforms are converted to DM_I2C that's why there is no reason to keep this code here. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Michal Simek 提交于
This driver is replaced by drivers/i2c/i2c-cdns.c DM based driver. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
由 Michal Simek 提交于
All platforms have been converted to DM that's why there is no reason to keep addresses in headers. They are all read from DT now. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Michal Simek 提交于
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio subsystem already. That's why also remove CMD_PCA953X which is only for this driver. zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address. DM_I2C is not enabled for the whole SoC because it increase size for mini configurations and there is no I2C symbol present to setup dependencies. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Michal Simek 提交于
All platforms have been converted to DM that's why there is no reason to keep addresses in headers. They are all read from DT now. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Michal Simek 提交于
All these board have also eeprom enabled that's why it is also enabled via defconfig. There is also no need to have zc70x specific config file that's why also remove it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Michal Simek 提交于
Boards have only one controller enabled that's why move to DM_I2C is easy. Add also i2c alias for not to be shown as i2c bus -1 because alias doesn't exist. Config file points to MAC stored in eeprom but it is not listed that's why I have added 24c08 part. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
This patch adds new mini target for versal. This configuration is very minimal in size which runs from OCM. It contains support for mtest which can be used for running DDR memory tests. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Move hardcoded IOU_SWITCH_DIVISOR0 to Kconfig to be able to set it up for different platforms. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Simplify code indentation. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch adds distro boot commands for qspi, ospi and mmc. The distro boot commands now reads the script from flash offset of 63.5MB for qspi and ospi and executes it. For mmc its same as generic distro boot command. As either one of the qspi or ospi can exist on hardware, defined a single distroboot command as xspi that works for both. Setup default location via script_offset_f to 63.5MB to match the most xilinx reference boards for qspi, ospi for now. 512kB allocated space for script size (script_size_f) should be more than enough to cover custom boot logic. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is no need to see this info. It is just wasting of space/time. It saves 308Bytes. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
Update boot_targets based on bootmode to run corresponding distroboot command first. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch adds distro boot commands for qspi, nand and nor. The distro boot commands now reads the script from flash offset of 15.75MB and executes it. Setup default location via script_offset_f to 15.75MB to match the most xilinx reference boards for qspi, nand and set the same using script_offset_nor to 0xE2EC0000 for nor. 256kB allocated space for script size (script_size_f) should be more than enough to cover custom boot logic. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Trivial patch. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch adds mini eMMC configuration which has only emmc0 and emmc1 functionalities and can run from small amount of memory. This is required for memory constraint devices. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
This platform is going to become generic that's why it is necessary also enable different PHY vendors. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch adds new config option which is used for reserving a specific memory for MMU Table and in this case we are using TCM for that purpose. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Convert board from OF_EMBED to OF_SEPARATE. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
It is much easier to point to eeprom which stores information like MAC address directly via DT. eeprom which contains this information is pointed by /chosen/xlnx,eeprom parameter. For example: chosen { bootargs = "earlycon"; stdout-path = "serial0:115200n8"; + xlnx,eeprom = &eeprom; }; Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Zynq and ZynqMP are sharing similar code and there is no reason to do code duplication. Move zynq_board_read_rom_ethaddr() to common file for easier conversion to DM. Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy which is only one Zynq board which is using this feature. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch adds distro boot commands for qspi and nand. The distro boot commands now reads the script from flash offset of 63.5MB and executes it. Setup default location via script_offset_f to 63.5MB to match the most xilinx reference boards. 512kB allocated space for script size (script_size_f) should be more than enough to cover custom boot logic. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
This patch is doing two things. 1. Exchanging order of boot commands. distro_bootcmd is run first followed by Xilinx boot command. 2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by creating Xilinx distribution bootcommand and wiring it as the last bootcommand. QSPI, NAND distribution boot command will be added later. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 13 2月, 2019 6 次提交
-
-
git://github.com/agraf/u-boot由 Tom Rini 提交于
Patch queue for efi - 2019-02-13 Goodness this time around: - HII protocol, finally allows us to run the UEFI Shell! (experimantal, disabled by default) - efi selftest now available on Cortex-M - NVMe support for distro boot - Lots of code cleanup
-
由 Heinrich Schuchardt 提交于
We check the existence of files with fs_exist(). This function calls fs_close(). If we do not set the active block device again fs_opendir() fails and we do not set the flag EFI_FILE_DIRECTORY. Due to this error the `cd` command in the EFI shell fails. So let's add the missing set_blk_dev(fh) call. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Heinrich Schuchardt 提交于
We have to ensure while printing UTF16 strings that we do not exceed the end of the print buffer. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Alexander Graf 提交于
Heinrich ran into issues with HII and iPXE which lead to #SErrors on his Odroid-C2 system. We definitely do not want to regress just yet, so let's not expose the HII protocols by default. Instead, let's make it a config option that people can play with This way, we can stabilize the code in tree without breaking any users. Once someone figures out, why this breaks iPXE (probably a NULL dereference), we can enable it by default. Reported-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: NAlexander Graf <agraf@suse.de> --- v1 -> v2: - Remove HII selftest as well v2 -> v3: - Make config option
-
由 Alexander Graf 提交于
Commit 81ea0083 ("efi_loader: PSCI reset and shutdown") put the SMCCC assembly code into the efi specific code section. This is wrong when we do not have EFI_LOADER enabled, as that strips efi runtime sections from the output binary Reported-by: NMichal Simek <monstr@monstr.eu> Reported-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Tested-by: NMichal Simek <monstr@monstr.eu> Fixes: 81ea0083 ("efi_loader: PSCI reset and shutdown") Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Heinrich Schuchardt 提交于
For correct indention use EFI_PRINT() instead of debug(). For printing efi_uintn_t or size_t use the %zu or %zx format code. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: NAlexander Graf <agraf@suse.de>
-