- 03 10月, 2015 1 次提交
-
-
由 Stephen Warren 提交于
In order to avoid any assumptions about any device connected to P2371-2180's expansion connector, the latest pinmux spreadsheet configures all muxable pins on that connector to be GPIO inputs, with on-chip pulls where appropriate. Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 29 9月, 2015 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 9月, 2015 19 次提交
-
-
由 Łukasz Majewski 提交于
The commit: d9dbb97b "mmc: dw_mmc: Zap endless timeout" removed endless loop waiting for end of dw mmc transfer. For some workloads - dfu test @ Odroid XU3 (sending 8MiB file) - and SD cards (e.g. MicroSD Kingston 4GiB, Adata 4GiB) the default timeout is to short. The new value - 4 minutes (240 seconds) - is the same as the one used in Linux kernel driver. Such fix should be good enough until we come up with better fix for this issue. Signed-off-by: NLukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Tom Rini <trini@konsulko.com> Tested-by: NPrzemyslaw Marczak <p.marczak@samsung.com>
-
由 Bin Meng 提交于
Give a full URL for a working nds32 toolchain for U-Boot. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Josh Wu 提交于
As 'time(0) | getpid()' will have a lot of duplicated value. It is not a expected behavior. We expect different value for the seed when when run it in many times. So this patch will left shift the getpid() and add to time(0). That avoid duplicated value. Test command is like: % RUN=0; while [ $RUN -lt 10000 ]; do tools/gen_eth_addr; RUN=$(($RUN+1)); done | sort | uniq | wc -l 10000 This patch is incorporated with suggestions made by Wolfgang Denk and Andreas Bießmann. Thanks them a lot. Signed-off-by: NJosh Wu <josh.wu@atmel.com> Acked-by: NAndreas Bießmann <andreas.devel@googlemail.com> Acked-by: NWolfgang Denk <wd@denx.de> Tested-by: NWolfgang Denk <wd@denx.de>
-
由 Simon Glass 提交于
This code is no-longer used. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org> Acked-by: NAndreas Bießmann <andreas.devel@gmail.com>
-
由 Simon Glass 提交于
This board has not been converted to generic board by the deadline. Remove it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This board has not been converted to generic board by the deadline. Remove it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Peter Griffin 提交于
DRAM region 0x3f000000 - 0x3fffffff is reserved for OP-TEE. Touching 0x3f000000 memory location from unsecure world causes the board to hang. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Peter Griffin 提交于
Use DM for the pl01x serial driver on hikey. Also allow UART0 or UART3 to be chosen via Kconfig. By default we now output to UART3 as the latest version of ATF outputs to this UART. Also UART3 comes out on the LS connector, as opposed to UART0 which goes to a unpopulated header. As part of this change we also enable CONFIG_BOARD_EARLY_INIT_F and call the pinmux configuration code for the UART. Before we were relying on ATF having already configured the pin configuration. NB: Upstream Linux kernel doesn't yet support UART3, so serial console will still be output on UART0 when booting a upstream kernel. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Peter Griffin 提交于
Most platforms enable these options from Kconfig rather than the configs header file. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Peter Griffin 提交于
This causes exceptions and other strange behaviour when enabling CONFIG_SYS_MALLOC_F_LEN which is required to migrate the serial driver over to DM_SERIAL. As GD_FLG_FULL_MALLOC_INIT flag gets reset, after relocation we don't end up using the full malloc which ultimately ends up causing a synchronus abort. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Peter Griffin 提交于
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Peter Griffin 提交于
Use the #defines in linux/sizes for malloc size as it is more readable. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Peter Griffin 提交于
Rather than relying on an external URL in the README include the Makefile in the hikey directory. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
-
由 Peter Griffin 提交于
The README had a few mistakes, and one of the URL's had changed. Also update the boot log with the latest boot trace from ATF, which now includes the mcuimage.bin. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
-
由 Philipp Rosenberger 提交于
The gd->malloc_ptr and the gd->malloc_limit are offsets to gd->malloc_base. But the addr variable contains the absolute address. The new_ptr must be: addr + bytes - gd->malloc_base. Signed-off-by: NPhilipp Rosenberger <ilu@linutronix.de> Reviewed-by: NHans de Goede <hdegoede@redhat.com>
-
由 Sekhar Nori 提交于
When AM437x EVM is connected to Gigabit switch, it takes more time to finish auto-negotiation than on a 10/100 switch. The default 4 second limit times-out more often than not. This is observed when testing with a D-Link DGS-1008A desktop switch. Increase the auto-negotiation time-out for AM437x EVM to handle this case. Signed-off-by: NSekhar Nori <nsekhar@ti.com>
-
由 Igor Grinberg 提交于
Fix typo in CONFIG_FIT description - remove the accidentially added redundand 'the'. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Igor Grinberg 提交于
The config option has been removed by one of the syncs with the Linux mainline MTD subsystem: ff94bc40 (mtd, ubi, ubifs: resync with Linux-3.14) It has been left inside the config files. Currently does not look to serve any purpose, so remove it now from all the configs. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Cc: Stefan Roese <sr@denx.de> Cc: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Simon Glass <sjg@chromium.org> Acked-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
Some boards' defconfigs are disordered. Reorder them. Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-
- 25 9月, 2015 4 次提交
-
-
-
-
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
- 24 9月, 2015 15 次提交
-
-
由 Masahiro Yamada 提交于
Currently, the USB boot mode is supported by an external loader and U-boot proper image is put on the section 0. This commit allows access there. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Before this commit, the Kconfig menu in mach-uniphier only allowed us to choose one SoC to be compiled. Each SoC has its own defconfig file for the build-test coverage. Consequently, some defconfig files are duplicated with only the difference in CONFIG_DEFAULT_DEVICE_TREE and CONFIG_{SOC_NAME}=y. Now, most of board-specific parameters have been moved to device trees, so it makes sense to include init code of multiple SoCs into a single image as long as the SoCs have similar architecture. In fact, some SoCs of UniPhier family are very similar: - PH1-LD4 and PH1-sLD8 - PH1-LD6b and ProXstream2 (will be added in the upcoming commit) This commit will be helpful to merge some defconfig files for better maintainability. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Currently, console=ttyS0 is hard-coded in CONFIG_EXTRA_ENV_SETTINGS and it replaces the bootargs in the chosen node of the device tree passed to the kernel. This is not preferable because I am going to add some boards whose console is not ttyS0. Drop bootargs settings from U-Boot's environment and use the one in device tree by default. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Move init code of low-level debug into a single file. This is helpful to create an image that runs on multiple SoCs. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Currently, IECTRL is enabled after pin-mux settings for the low-level debugging for PH1-LD4 and PH1-sLD8. While IECTRL is disabled, input signals are pulled-down, i.e. glitch signal (Low to High transition) problem occurs if pin-mux is set up first. As a result, one invalid character is input to the UART block and the auto-boot counting is terminated immediately. The correct initialization procedure is: [1] Enable IECTRL (if IECTRL exists for the pins) [2] Set up pin-muxing [3] Deassert the reset of the hardware block Currently, the low-level debugging is working for PH1-sLD3 and PH1-Pro4, but just in case, follow the sequence for all the SoCs. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The UART I/O ports for PH1-Pro4 has no input enable controlling. This code is useless. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
I want these prefixed with CONFIG_ARCH_UNIPHIER_ to clarify they belong to UniPhier SoC family. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Without this, build fails if CONFIG_MICRO_SUPPORT_CARD is disabled. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
It is no longer necessary to define CONFIG_SUPPORT_CARD_* globally. Move them to a C file as local macros. Also, rename the C file. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The macro, led_write(), is now only used in C sources. There is no more reason to keep the tricky assembly macro. Replace it with a new C function led_puts(). Also, rename board.h to micro-support-card.h. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The wrapper functions, uniphier_board_*, are just making function calls complex. Remove them. Also, use empty inline functions in case CONFIG_MICRO_SUPPORT_CARD is disabled, so that prototype checking works. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
This has been unused since commit f4e190e3 ("ARM: uniphier: enable SPL_OF_CONTROL"). Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Device tree specifies the available memory ranges in its "/memory" node. Use it to simplify the CONFIG defines. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-