ARM: uniphier: fix glitch signal problem for low-level debug

Currently, IECTRL is enabled after pin-mux settings for the low-level
debugging for PH1-LD4 and PH1-sLD8.  While IECTRL is disabled, input
signals are pulled-down, i.e. glitch signal (Low to High transition)
problem occurs if pin-mux is set up first.  As a result, one invalid
character is input to the UART block and the auto-boot counting is
terminated immediately.

The correct initialization procedure is:
 [1] Enable IECTRL (if IECTRL exists for the pins)
 [2] Set up pin-muxing
 [3] Deassert the reset of the hardware block

Currently, the low-level debugging is working for PH1-sLD3 and
PH1-Pro4, but just in case, follow the sequence for all the SoCs.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

arch/arm/mach-uniphier/ph1-ld4/lowlevel_debug.S

@@ -14,16 +14,16 @@
 #include <mach/debug-uart.S>
 
 ENTRY(setup_lowlevel_debug)
-		init_debug_uart	r0, r1, r2
+		ldr		r0, =SG_IECTRL
+		ldr		r1, [r0]
+		orr		r1, r1, #1
+		str		r1, [r0]
 
 		/* UART Port 0 */
 		sg_set_pinsel	85, 1, 8, 4, r0, r1
 		sg_set_pinsel	88, 1, 8, 4, r0, r1
 
-		ldr		r0, =SG_IECTRL
-		ldr		r1, [r0]
-		orr		r1, r1, #1
-		str		r1, [r0]
+		init_debug_uart	r0, r1, r2
 
 		mov		pc, lr
 ENDPROC(setup_lowlevel_debug)

arch/arm/mach-uniphier/ph1-pro4/lowlevel_debug.S

@@ -15,13 +15,6 @@
 #include <mach/debug-uart.S>
 
 ENTRY(setup_lowlevel_debug)
-		ldr		r0, =SC_CLKCTRL
-		ldr		r1, [r0]
-		orr		r1, r1, #SC_CLKCTRL_CEN_PERI
-		str		r1, [r0]
-
-		init_debug_uart	r0, r1, r2
-
 		/* UART Port 0 */
 		sg_set_pinsel	127, 0, 4, 8, r0, r1
 		sg_set_pinsel	128, 0, 4, 8, r0, r1
@@ -30,5 +23,12 @@ ENTRY(setup_lowlevel_debug)
 		mov		r1, #1
 		str		r1, [r0]
 
+		ldr		r0, =SC_CLKCTRL
+		ldr		r1, [r0]
+		orr		r1, r1, #SC_CLKCTRL_CEN_PERI
+		str		r1, [r0]
+
+		init_debug_uart	r0, r1, r2
+
 		mov		pc, lr
 ENDPROC(setup_lowlevel_debug)

arch/arm/mach-uniphier/ph1-sld3/lowlevel_debug.S

@@ -15,6 +15,9 @@
 #include <mach/debug-uart.S>
 
 ENTRY(setup_lowlevel_debug)
+		sg_set_pinsel	63, 0, 4, 4, r0, r1
+		sg_set_pinsel	64, 1, 4, 4, r0, r1
+
 		ldr		r0, =BCSCR5
 		ldr		r1, =0x24440000
 		str		r1, [r0]
@@ -26,8 +29,5 @@ ENTRY(setup_lowlevel_debug)
 
 		init_debug_uart	r0, r1, r2
 
-		sg_set_pinsel	63, 0, 4, 4, r0, r1
-		sg_set_pinsel	64, 1, 4, 4, r0, r1
-
 		mov		pc, lr
 ENDPROC(setup_lowlevel_debug)

arch/arm/mach-uniphier/ph1-sld8/lowlevel_debug.S

@@ -14,16 +14,16 @@
 #include <mach/debug-uart.S>
 
 ENTRY(setup_lowlevel_debug)
-		init_debug_uart	r0, r1, r2
+		ldr		r0, =SG_IECTRL
+		ldr		r1, [r0]
+		orr		r1, r1, #1
+		str		r1, [r0]
 
 		/* UART Port 0 */
 		sg_set_pinsel	70, 3, 8, 4, r0, r1
 		sg_set_pinsel	71, 3, 8, 4, r0, r1
 
-		ldr		r0, =SG_IECTRL
-		ldr		r1, [r0]
-		orr		r1, r1, #1
-		str		r1, [r0]
+		init_debug_uart	r0, r1, r2
 
 		mov		pc, lr
 ENDPROC(setup_lowlevel_debug)