This patch sets CONFIG_SYS_BOOTMAPSZ to the amount of memory available
to safely contain a kernel, device tree and initrd for relocation. The
way to set fdt_high as 0xffffffff to disable device tree relocation is
removed.
Signed-off-by: NAlison Wang <alison.wang@nxp.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: NTom Rini <trini@konsulko.com>

Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: NAlison Wang <alison.wang@nxp.com>
Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Tested-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: NStefan Roese <sr@denx.de>
Tested-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed

This converts the following to Kconfig:
   CONFIG_MISC_INIT_R
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC
Signed-off-by: NAdam Ford <aford173@gmail.com>
Acked-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.
Signed-off-by: NTom Rini <trini@konsulko.com>

There is no reason to define default option for this macro which is
already done in common/cli_hush.c.

  86 #ifndef CONFIG_SYS_PROMPT_HUSH_PS2
  87 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
  88 #endif
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: NTom Rini <trini@konsulko.com>

CONFIG_SPL_SERIAL_SUPPORT had already been migrated to Kconfig, but
existed in some include files; fix those up here.
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>

Migrate the CONFIG_FSL_ESDHC option to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Migrate the CONFIG_TSEC_ENET option to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: NTom Rini <trini@konsulko.com>

A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS.  As they plainly intended to, set that flag and
re-sync config files.
Signed-off-by: NTom Rini <trini@konsulko.com>

Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig.  We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important.  In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.
Signed-off-by: NTom Rini <trini@konsulko.com>

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: NTom Rini <trini@konsulko.com>

This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

And use 'imply' liberally.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

Because COMFIG_DM_USB has been enabled and will not use it anymore.
Signed-off-by: NRan Wang <ran.wang_1@nxp.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

use Kconfig to select xhci accordingly.
Signed-off-by: NRan Wang <ran.wang_1@nxp.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Use Kconfig to select QE-HDLC and USB pin-mux.
Signed-off-by: NRan Wang <ran.wang_1@nxp.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

The option is specified in Kconfig, but still a few config header files
are overriding the choice by #undef'ing it. Re-sync the option with
moveconfig to rid of the #undefs.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

CONFIG_CMD_BOOTZ symbol does not work in board config file
anymore, so fix this by moving it to Kconfig.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This commit removes definitions of CONFIG_SYS_BARGSIZE defined to be
equal to CONFIG_SYS_CBSIZE in numerous configuration files.

We remove such definitions in two situations:

 - CONFIG_SYS_CBSIZE is otherwise not defined in the board
   configuration file, which means the default value of
   CONFIG_SYS_CBSIZE == 256 applies. In this case, the default value
   of CONFIG_SYS_BARGSIZE == 512 (common/image.c) is suitable, as it is
   larger.

 - CONFIG_SYS_CBSIZE is defined in the board configuration file, but
   to a value equal or less than 512. In this case, the default value
   of CONFIG_SYS_BARGSIZE == 512 (common.image.c) is suitable, as it
   is equal or larger.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: NTom Rini <trini@konsulko.com>

This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files.  This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB.  Leaving this as-is results in a build failure, and
without work, run time failure.  The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot.  The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.
Signed-off-by: NTom Rini <trini@konsulko.com>

With the hierarchical defaults set up, we remove these from the header
files.  To do so, I've run moveconfig on SPL_LDSCRIPT and this commits
the changes.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_SCSI

Also update the Makefile to use CONFIG_CMD_SCSI instead of CONFIG_SCSI to
enable the command, fixing an earlier error.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Rework to default y if SCSI, drop cl-som-am57x which did not use
CMD_SCSI for real]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_PCI
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Reviewed-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Signed-off-by: NAlexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NStefan Roese <sr@denx.de>
Tested-by: NStefan Roese <sr@denx.de>

This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_SPI_FLASH
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

Now that these symbols are in Kconfig, migrate all users.  Use imply on
a number of platforms that default to having this enabled.  As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.
Signed-off-by: NTom Rini <trini@konsulko.com>