After this change one can run 'gpt' command on production u-boot.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

This code performs DDR3 memory calibration for display5 board.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Test case:

The fitImage gets corrupted:

truncate -c -s 3M fitImage
run tftp_mmc_fitImg
setenv boot_os y
reset

[board shall hang in SPL with
"Trying to boot from MMC1" information]

Then after X seconds WDT is causing board to reset. After N boot attempts
we enter recovery mode.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

The SPI-NOR partition information has been updated to store
swupdate-kernel-FIT just after envs as well as two times larger
swupdate-initramfs image.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

This is a prerequisite patch to combine SWUpdate and Linux recovery
initramfs images.

It removes the support for it.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

To test if this partition is present - one needs to write:
display5 > sf probe; mtdparts
display5 > sf erase factory +0x100000
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

The boot count is enabled in both SPL and proper u-boot.
Signed-off-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NStefan Roese <sr@denx.de>

This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>

Migrate the CONFIG_FSL_ESDHC option to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: NTom Rini <trini@konsulko.com>

Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: NTom Rini <trini@konsulko.com>

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>

This commit provides support for LWN's IMX6Q based DISPLAY5 board.
Signed-off-by: NLukasz Majewski <lukma@denx.de>