After this change one can run 'gpt' command on production u-boot.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Signed-off-by: NLukasz Majewski <lukma@denx.de>

Signed-off-by: NLukasz Majewski <lukma@denx.de>

Signed-off-by: NLukasz Majewski <lukma@denx.de>

This code performs DDR3 memory calibration for display5 board.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

After moving to swupdate 2017.07, the default fs for swupdate rootfs
is ext4, not ext3.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

After splitting rootfs images to BACKUP and ACTIVE, the "factory"
u-boot also needs to update the former.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Signed-off-by: NLukasz Majewski <lukma@denx.de>

Test case:

The fitImage gets corrupted:

truncate -c -s 3M fitImage
run tftp_mmc_fitImg
setenv boot_os y
reset

[board shall hang in SPL with
"Trying to boot from MMC1" information]

Then after X seconds WDT is causing board to reset. After N boot attempts
we enter recovery mode.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

To enter the special mode, one needs to short cut two pads with e.g. screw
driver.

After power up the SPL will execute u-boot in which proper actions will be
taken.

It is worth noting that we do not alter envs (even the BOOT_FROM variable)
and unconditionally go to recovery.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

This special partition has been added solely for production purpose.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

The SPI-NOR partition information has been updated to store
swupdate-kernel-FIT just after envs as well as two times larger
swupdate-initramfs image.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

This is a prerequisite patch to combine SWUpdate and Linux recovery
initramfs images.

It removes the support for it.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Since display5 is now supporting boot counting, we can just reset the
board when bootm fails (i.e. it doesn't boot the fitImage kernel for
any reason).
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Force booting through u-boot proper when environment error encountered
(as a result of either broken SPI-NOR or erased envs).
Signed-off-by: NLukasz Majewski <lukma@denx.de>

It may be necessary to update the content of the whole SPI-NOR memory at
once with using a single command (tftp_sf_img).
Signed-off-by: NLukasz Majewski <lukma@denx.de>

To test if this partition is present - one needs to write:
display5 > sf probe; mtdparts
display5 > sf erase factory +0x100000
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Signed-off-by: NLukasz Majewski <lukma@denx.de>

When BOOT_FROM = FACTORY, then the LEG's factory setup is performed.

This code relies on boot_nfs u-boot command, so it shall be adjusted
appropriately (e.g. provide proper fitImage file).
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Here we just add a tool for HSDK flashable images preparation
together with extensive documentation for HSDK board.

This will help real-life users to update U-Boot on the board.

Xilinx fixes for v2018.07-rc2

Zynq:
- Fix missing watchdog header
- DT fixes

ZynqMP:
- emmc configuration split
- Enable SPD
- Fix PMUFW_INIT_FILE logic
- Coverity fixes in SoC code

timer
- Add timer_get_boot_us

mmc:
- Fix MMC HS200 tuning command

serial:
- Fix scrabled chars with OF_LIVE

Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>

HSDK board has preloader that reads SPI flash pages and searches
for a special image header to fetch and load binary.

Add tool, make target (bsp-generate) to generate
update script and u-boot binary image with header for preloader.

Also add script to default environment to apply updates.
Signed-off-by: NEugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>

This function is used only inside this driver that's why should be
static.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This issue was found when OF_LIVE was enabled that there are scrambled
chars on the console like this:
Chip ID:	zu3eg
Watchdog: Started��j�   sdhci@ff160000: 0, sdhci@ff170000: 1
In:    serial@ff010000

I found a solution for this problem exactly the same as I found later in
serial_msm fixed by:
"serial: serial_msm: initialize uart only before relocation"
(sha1: 7e5ad796)

What it is happening is that output TX fifo still contains chars to be
sent and _uart_zynq_serial_init() resets TX fifo even in the middle of
transfer.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Change logic and put char to fifo till there is a space in output fifo.
Origin logic was that output fifo needs to be empty. It means only one
char was in output queue.
Also remove unused ZYNQ_UART_SR_TXEMPTY macro.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Coding style is checking to use BIT macros instead of shifts.
The patch is also fixing the rest of macros which should be BITs instead
of hex numbers.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Use u32 instead of int for max_bank, bank_min and bank_max. These values
can't be negative that's why no reason to use signed type.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

There should be return value check from zynqmp_mmio_read() in
zynqmp_mmio_rawwrite() to make sure that errors are propagated properly.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

calloc() can fail and return NULL. The patch is checking return value
and return in case of error.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Code around tuning_loop_counter variable expects to go below zero.
That's why this variable can't use unsigned type.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

There is no reason to check that unsigned type that is >= 0.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch fixes the mmc tuning command failures
when tuning pattern data needs to read back for
comparision against the expected bit pattern.
Reported-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Tested-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The value of PMUFW_INIT_FILE is prefixed with "$(srctree)/", thus
forcing it to be a relative path inside the U-Boot source tree. Since
the PMUFW is a binary file generated outside of U-Boot, the PMUFW
binary must be copied inside the U-Boot source tree before the
build.

This generates a few problems:

 * if the source tree is shared among different out-of-tree builds,
   they will pollute (and potentially corrupt) each other
 * the source tree cannot be read-only
 * any buildsystem must add a command to copy the PMUFW binary
 * putting an externally-generated binary in the source tree is ugly
   as hell

Avoid these problems by accepting an absolute path for
PMUFW_INIT_FILE. This would be as simple as removing the "$(srctree)/"
prefix, but in order to keep backward compatibility we rather use the
shell and readlink to get the absolute path even when starting from a
relative path.

Since 'readlink -f' produces an empty string if the file does not
exist, we also add a check to ensure the file configured in
PMUFW_INIT_FILE exists. Otherwise the build would exit successfully,
but produce a boot.bin without PMUFW as if PMUFW_INIT_FILE were empty.

Tested in the 12 possible combinations of:
 - PMUFW_INIT_FILE empty, relative, absolute, non-existing
 - building in-tree, in subdir, in other directory
Signed-off-by: NLuca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

zcu102 contains DIMM with SPD on it at 0x51 address.
For example:
i2c dev 13
i2c sdram 51
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This function is required for adding bootstage support.
Also enable it directly for ZynqMP R5 configuration.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

dtc is showing some warnings and this change was also done in
the Linux kernel as "Input: gpio-keys - clean up device tree binding
example"
with this fragment in commit message
"Drop #address-cells and #size-cells, which are not required by the
gpio-keys binding documentation, as button sub-nodes are not devices."
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
systems which have only one interface mini configuration is failing on
unused interface. This patch also adds required clock node in dts and
enables CONFIG_MMC_SDHCI_ZYNQ through defconfig.
Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add missing header detected by sparse.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>