- 05 3月, 2014 1 次提交
-
-
由 pekon gupta 提交于
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI params or nand_id[] table. And based on that it defines ECC layout. This patch 1) removes following board configs used for defining NAND ECC layout - GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND) - GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND) - GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND) - GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND) 2) removes unused #defines in common omap_gpmc.h depending on above configs Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5 Signed-off-by: NPekon Gupta <pekon@ti.com>
-
- 22 2月, 2014 2 次提交
-
-
由 Stefano Babic 提交于
Patch allows to load a script at the startup from MMC. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
Patch contains the same fixes as commit 4b9b2c30 (missing CONFIG_OMAP3_GPIO_2) and commit f9095aac793aa8917ab9b915c5d449e6dc8d3d30 (missing CONFIG_SPL_NAND_SOFTECC). Same issues are relevant for the mcx board, too. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
- 22 11月, 2013 1 次提交
-
-
由 pekon gupta 提交于
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed CONFIG_xx used for selecting NAND ecc-schemes. This patch aims at solving following issues. 1) Currently ecc-scheme is tied to SoC platform, which prevents user to select other ecc-schemes also supported in hardware. like; - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW). - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware supports BCH16 ecc-scheme also. 2) Different platforms use different CONFIG_xx to select ecc-schemes, which adds confusion for user while migrating platforms. - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only 8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW) whereas ELM hardware engine supports other ecc-schemes also like; BCH4, and BCH16 (in future). - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW). - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency on SoC platform and NAND driver. And user can select ecc-scheme independently foreach board. However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand) Signed-off-by: NPekon Gupta <pekon@ti.com>
-
- 13 11月, 2013 1 次提交
-
-
由 Heiko Schocher 提交于
- add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/Signed-off-by: NHeiko Schocher <hs@denx.de> Tested-by: NTom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: NIgor Grinberg <grinberg@compulab.co.il> Acked-by: NStefano Babic <sbabic@denx.de>
-
- 05 11月, 2013 1 次提交
-
-
由 Rob Herring 提交于
Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
- 20 8月, 2013 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
- 15 8月, 2013 1 次提交
-
-
由 Lokesh Vutla 提交于
Adding a new CONFIG_OMAP_COMMON which is included by all boards that needs to build cpu/armv7/omap-common folder. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
- 24 7月, 2013 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: NTom Rini <trini@ti.com>
-
- 29 1月, 2013 1 次提交
-
-
由 Michael Jones 提交于
"CONFIG_SYS_I2C_BUS" and "CONFIG_SYS_I2C_BUS_SELECT" don't appear anywhere outside of config files. Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de> Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
-
- 11 12月, 2012 1 次提交
-
-
由 Thomas Weber 提交于
Remove the unused PHYS_SDRAM_1_SIZE from OMAP3 config files. Signed-off-by: NThomas Weber <thomas@tomweber.eu>
-
- 27 11月, 2012 1 次提交
-
-
由 Scott Wood 提交于
Some small SPLs do not use nand_base.c, and a subset of those also require a special driver. Some SPLs need software ECC but others can't fit it. All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these symbols added to preserve existing behavior. Signed-off-by: NScott Wood <scottwood@freescale.com> -- v2: use positive logic for including bits of NAND, rather than a MINIMAL symbol that excludes things.
-
- 20 11月, 2012 1 次提交
-
-
由 Jeroen Hofstee 提交于
CONFIG_EHCI_DCACHE was removed by commit b8adb120 "USB: Drop cache flush bloat in EHCI-HCD". Remove the defines from the boards configs as well. Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl> cc: Marek Vasut <marex@denx.de> cc: Stefan Roese <sr@denx.de> cc: Tom Rini <trini@ti.com> cc: Wolfgang Denk <wd@denx.de> cc: Thierry Reding <thierry.reding@avionic-design.de> cc: Tom Warren <twarren@nvidia.com> cc: Stephen Warren <swarren@nvidia.com> cc: Stefano Babic <sbabic@denx.de>
-
- 26 10月, 2012 3 次提交
-
-
由 Stefano Babic 提交于
Add video support to the board with the display focaltech etm070003dh6. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
Some GPIOs differ in the new revision board. Previous revision are considered obsolete and they will not anymore supported. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
The mcx board was slightly modified and the pinmux must be updated. There is no need to support the old board, that becomes obsolete. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
- 28 9月, 2012 2 次提交
-
-
由 Tom Rini 提交于
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL framework, enable on all of the previously using boards. We move the spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave the NAND one in-place as we plan to replace it later in this series. We use common/spl to avoid linker problems with respect to merging constant strings in objects. Otherwise all strings in common/ will be linked in and kept which grows SPL in size too much. Signed-off-by: NTom Rini <trini@ti.com>
-
由 Tom Rini 提交于
This is an OMAP/related-specific function, move calling it to spl_board_init() and turn on CONFIG_SPL_BOARD_INIT on the boards that enabled NAND and didn't enable this already. Signed-off-by: NTom Rini <trini@ti.com>
-
- 01 9月, 2012 5 次提交
-
-
由 Rob Herring 提交于
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present in most ARM board config files. IRQs are only enabled for 1 config, so remove the unused config options for IRQ and FIQ stack size as well. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: NTom Rini <trini@ti.com> Signed-off-by: NTom Rini <trini@ti.com>
-
由 Stefano Babic 提交于
Detect hot-water-button to start a differnt image. Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
-
由 Stefano Babic 提交于
Patch drops also not used CFI setup in the configuration file. Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
-
由 Stefano Babic 提交于
Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
-
- 21 6月, 2012 1 次提交
-
-
由 Tom Rini 提交于
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value different than "> " which is vision2. I have Cc'd the maintainer here as I strongly suspect this is a bug rather than intentional behavior. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: NTom Rini <trini@ti.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
- 15 5月, 2012 2 次提交
-
-
由 Tom Rini 提交于
With older toolchains it is possible to not fit entirely into the 45KB that we had assigned to SPL. Adjust to allow for 8KB of stack (which should be more than required) and 54KB of text/data. Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Thomas Weber <weber@corscience.de> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: NTom Rini <trini@ti.com> Acked-by: NStefano Babic <sbabic@denx.de> Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
-
由 Tom Rini 提交于
This define does not control anything, remove it. Signed-off-by: NTom Rini <trini@ti.com>
-
- 28 2月, 2012 2 次提交
-
-
由 Detlev Zundel 提交于
Signed-off-by: NDetlev Zundel <dzu@denx.de> CC: Stefano Babic <sbabic@denx.de>
-
由 Thomas Weber 提交于
Signed-off-by: NThomas Weber <weber@corscience.de>
-
- 12 2月, 2012 2 次提交
-
-
由 Ilya Yanok 提交于
This patch adds support for the HTKW mcx AM3517-based board. Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both NAND and MMC SPLs are supported. Signed-off-by: NIlya Yanok <yanok@emcraft.com> Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> Cc: Detlev Zundel <dzu@denx.de> Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
-
由 Yegor Yefremov 提交于
it is not necessary to define rootfstype for mass storage devices. Kernel detects it automatically. Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
-
- 27 1月, 2012 1 次提交
-
-
由 Stefano Babic 提交于
Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM which is likely to contain already loaded data. The patch saves the oob data and the ecc on the stack replacing the fixed address in RAM. Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Ilya Yanok <yanok@emcraft.com> CC: Scott Wood <scottwood@freescale.com> CC: Tom Rini <tom.rini@gmail.com> CC: Simon Schwarz <simonschwarzcor@googlemail.com> CC: Wolfgang Denk <wd@denx.de> Signed-off-by: NScott Wood <scottwood@freescale.com>
-
- 07 12月, 2011 3 次提交
-
-
由 Tom Rini 提交于
The only change of note is that we move from 0x80008000 to 0x80100000 for CONFIG_SYS_TEXT_BASE Cc: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: NTom Rini <trini@ti.com>
-
由 Thomas Weber 提交于
This patch removes the definition of stack sizes for irq and fiq if the CONFIG_USE_IRQ is undefined before. Acked-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NTom Rini <trini@ti.com> Acked-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NThomas Weber <weber@corscience.de> Acked-by: NLuca Ceresoli <luca.ceresoli@comelit.it>
-
由 Thomas Weber 提交于
This patch removes the unused definition of SDRC_R_C_B from the config files. Acked-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NThomas Weber <weber@corscience.de> Acked-by: NLuca Ceresoli <luca.ceresoli@comelit.it> Acked-by: NTom Rini <trini@ti.com>
-
- 22 10月, 2011 1 次提交
-
-
由 Joe Hershberger 提交于
Remove MK_STR from places that consume CONFIG_BOOTFILE to force all definitions to be string literals. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: NMike Frysinger <vapier@gentoo.org>
-
- 04 9月, 2011 1 次提交
-
-
由 Vaibhav Hiremath 提交于
Switch from the legacy mmc driver to the new generic mmc driver. This patch is based on similar patch for beagle[1]. [1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: NSanjeev Premi <premi@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 04 8月, 2011 1 次提交
-
-
由 Christopher Harvey 提交于
Signed-off-by: NChristopher Harvey <charvey@matrox.com>
-
- 18 7月, 2011 1 次提交
-
-
由 Yegor Yefremov 提交于
the serial device names have been changed from ttySx to ttyOx, so the console device name should be also changed to support the latest kernel versions. Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com> Acked-by: Vaibhav Hiremath<hvaibhav@ti.com>
-
- 13 5月, 2011 1 次提交
-
-
由 Michael Jones 提交于
commit 25ddd1fb left remnants of many comments about CONFIG_SYS_GBL_DATA_SIZE. Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de>
-
- 28 4月, 2011 1 次提交
-
-
由 Luca Ceresoli 提交于
Removed boot_flash_* extern variables. boot_flash_type was totally unused. The other ones were actually constants, so they have been replaced with #defines in the board config files. Signed-off-by: NLuca Ceresoli <luca.ceresoli@comelit.it> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.aribaud@free.fr> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-