- 04 2月, 2014 6 次提交
-
-
由 Priyanka Jain 提交于
Add usb2 node entry in "hwconfig string" Remove controller interleaving from hwconfig string as T1040 has only one DDR conroller SPI related macros which were earlier under #ifdef CONFIG_SPIFLASH are move outside so that they are defined for all cases as these macros are also used by other u-boot code Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com> [York Sun: Minor change to commit message] Signed-off-by: NYork Sun <yorksun@freescale.com>
-
由 Prabhakar Kushwaha 提交于
Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5 Define MDIO related configs Added eth.c file Update t1040.c to support RGMII and SGMII Update t1040qds.c to support ethernet Define the PHY address Signed-off-by: NArpit Goel <B44344@freescale.com> Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> [York Sun: remove dash from commit message] Signed-off-by: NYork Sun <yorksun@freescale.com>
-
由 Prabhakar Kushwaha 提交于
T1040 has only one SerDes block. so update the code accordingly. Also, add support of SerDes Protocol 0x00, 0x06, 0x40, 0x69 0x85, 0xA7 and 0xAA Signed-off-by: NArpit Goel <B44344@freescale.com> Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Prabhakar Kushwaha 提交于
Due to increased size of u-boot, FMAN ucode start address has been shifted by 256KB causing a overlap with rootfs start address. Update rootfs start address to reflect correct memory map. Also fix minor typo in README Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Prabhakar Kushwaha 提交于
Current print only display width of PCIe device. Add print to display PCIe generation supported by the device. Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 poonam aggrwal 提交于
Removed LIODNs for RMAN, RIO, 10G. T1040 has 10 QMAN portals so assigned LIODNs accordingly. Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 30 1月, 2014 2 次提交
-
-
由 Ezequiel Garcia 提交于
If CONFIG_CFI_FLASH_MTD is not defined, then we shouldn't perform the flash early reset. This commit fixes the following build error: nios2-generic.c: In function `__early_flash_cmd_reset': nios2-generic.c:23: error: `AMD_CMD_RESET' undeclared (first use in this function) nios2-generic.c:23: error: (Each undeclared identifier is reported only once nios2-generic.c:23: error: for each function it appears in.) nios2-generic.c:24: error: `FLASH_CMD_RESET' undeclared (first use in this function) which was introduced by: commit a113fb39 Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Date: Fri Dec 20 18:34:53 2013 -0300 board: nios2: Add CONFIG_CFI_FLASH_MTD guard to flash.h header include Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com> Cc: Thomas Chou <thomas@wytron.com.tw> Reported-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
-
由 Masahiro Yamada 提交于
Commit cbe5cdfc changed config.mk and arch/sandbox/cpu/Makefile to use -idirafter instead of -I and remove -nostdinc. But * Sandbox-specific code dirties config.mk * os.c is compiled without such compiler flags as: -Wall -Wstrict-prototypes -Wno-format-security -fno-builtin -ffreestanding -fno-stack-protector -fstack-usage -Wno-format-nonliteral This commit use -idirafter and remove the -nostdinc differently and more simply. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
- 28 1月, 2014 1 次提交
-
-
由 rick 提交于
hardware difference between leopard and orca as below: flash setting leoaprd orca bank size 32MB 64MB bus width 32-bits 16-bits Signed-off-by: Nrick <rick@andestech.com> Signed-off-by: NKuan-Yu Kuo <ken.kuoky@gmail.com>
-
- 27 1月, 2014 2 次提交
-
-
由 Fabio Estevam 提交于
Run "tools/reformat.py -i -d '-' -s 8 <boards.cfg >boards0.cfg && mv boards0.cfg boards.cfg" in order to keep the entries sorted. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Alexey Brodkin 提交于
This is only required for "PIC" relocation and doesn't apply to modern "PIE" relocation which does data relocation as well as code. "init_sequence_r" is just an array that consists of compile-time adresses of init functions. Since this is basically an array of integers (pointers to "void" to be more precise) it won't be modified during relocation - it will be just copied to new location as it is. As a consequence on execution after relocation "initcall_run_list" will be jumping to pre-relocation addresses. As long as we don't overwrite pre-relocation memory area init calls are executed correctly. But still it is dangerous because after relocation we don't expect initially used memory to stay untouched. Cc: Tom Rini <trini@ti.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Doug Anderson <dianders@chromium.org> Cc: Thomas Langer <thomas.langer@lantiq.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
-
- 25 1月, 2014 29 次提交
-
-
由 Dan Murphy 提交于
Add the USB host boot support for the am43xx evm Add the macros to boot from a usb drive in uBoot Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Dan Murphy 提交于
Add SPL support to be able to detect a USB Mass Storage device connected to a USB host. Once a USB Mass storage device is detected the SPL will load the u-boot.img from a FAT partition to target address. Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Dan Murphy 提交于
Move the FAT functions to a common location for reuse. Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_MPC5xxx in board config headers (and start.S) because it is defined in arch/powerpc/cpu/mpc5xxx/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Delete some serial.h files, whole code in which is surrounded by #if 0 ... #endif Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NStefan Roese <sr@denx.de>
-
由 Masahiro Yamada 提交于
The function os_free() returns nothing. Its return type should be "void" rather than "void *". Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Before this commit, all arch/arm/cpu/${CPU}/config.mk except ARMv8 had the same option: $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) This commit moves it into arch/arm/config.mk. If the compiler does not support the option, it is ignored by $(call cc-option,...). So this commit gives no harm to ARMv8. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Define CONFIG_MPC86xx in arch/powerpc/cpu/mpc86xx/config.mk because all target boards with mpc86xx cpu define it. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk because all target boards with mpc85xx cpu define it. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_MPC824X in board config headers because it is defined in arch/powerpc/cpu/mpc824x/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_5xx in a source file because it is defined in arch/powerpc/cpu/mpc5xx/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_MPC512X in board config headers because it is defined in arch/powerpc/cpu/mpc512x/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_8xx in source files because it is defined in arch/powerpc/cpu/mpc8xx/config.mk Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_MPC83xx in board config headers because it is defined in arch/powerpc/cpu/mpc83xx/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_4xx in board config headers because it is defined in arch/powerpc/cpu/ppc4xx/config.mk. include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx". I believe it is a typo because "CONFIG_4x" is not used at all in other files. So, I also deleted "CONFIG_4x" in include/configs/JSE.h. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Commit e5c5301f refactored the build system not to make directories in board makefiles. But commit 8f380381 create directories again in board/avionic-design/tec-ng/Makefile. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Alban Bedel <alban.bedel@avionic-design.de>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NStefan Roese <sr@denx.de> Acked-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Like other architectures, CONFIG_AVR32 can be defined in arch/avr32/config.mk rather than board header files. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Masahiro Yamada 提交于
Commit 643aae14 deleted include/linux/config.h but missed to delete _LINUX_CONFIG_H macro. It is no longer used at all. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
The script files, define2mk.sed and make-asm-offsets are used to create autoconf.mk and asm-offsets.h while build. Whereas README, dot.kermrc, flash_param, send_cmd, send_image are files useful for kermit. We should not put files which have the totally different purpose into the same directory. This commit creates a new directory, tools/kermit, and move kermit files into it. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Darwin Rambo 提交于
When CONFIG_SYS_VSNPRINTF is enabled, it protects print operations such as sprintf, snprintf, vsnprintf, etc., from buffer overflows. But vsnprintf_internal includes the terminating NULL character in the calculation of number of characters written. This affects sprintf and snprintf return values. Fix this issue by setting pointer 'str' back to the location of the '\0'. Signed-off-by: NDarwin Rambo <drambo@broadcom.com> Reviewed-by: NSteve Rae <srae@broadcom.com>
-
由 Darwin Rambo 提交于
If timer_init() is made a weak stub function, then it allows us to remove several empty timer_init functions for those boards that already have a timer initialized when u-boot starts. Architectures that use the timer framework may also remove the need for timer.c. Signed-off-by: NDarwin Rambo <drambo@broadcom.com> Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
-