this patch fixed following warning.
tzpc_init.c: In function 'tzpc_init':
tzpc_init.c:35: warning: assignment from incompatible pointer type
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Cc: Chander Kashyap <chander.kashyap@linaro.org>

TRATS target uses MAX8997 PMIC device instead of MAX8998.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMinkyu Kang <mk7.kang@samsung.com>

This commit adds support for MAX8997 PMIC driver.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NStefano Babic <sbabic@denx.de>

Trats is supported 1GiB memory size.
(Each bank size is 512MB.)
And INITRD is unnecessary. So removed them.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

This patch enables LDO4 power line for preparing proper voltages to be
measured by ADC converter.
This measurement is used for determination of target board HW revision.

Test HW:
Universal_C210 (Exynos4210) rev. 0.0
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

TZPC IP is common across Exynos based SoC'c. Renaming exynos5_tzpc
in arch/arm/include/asm/arch-exynos/tzpc.h to exynos_tzpc will allow generic
usase of tzpc.

Also modify board/samsung/smdk5250/tzpc_init.c to use exynos_tzpc.
Signed-off-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

With almost all the architecture and board BOARD_LATE_INIT does not use.
CONFIG_BOARD_LATE_INIT is used instead.
This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: NStefano Babic <sbabic@denx.de>

With almost all the architecture and board BOARD_LATE_INIT does not use.
CONFIG_BOARD_LATE_INIT is used instead.
This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Heiko Schocher <hs@denx.de>
Acked-by: NHeiko Schocher <hs@denx.de>

Enable I2C multi-bus support and config I2C muxes for I2C2 and I2C3.
Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>

This define does not control anything, remove it.
Signed-off-by: NTom Rini <trini@ti.com>

This define does not control anything, remove it.
Signed-off-by: NTom Rini <trini@ti.com>

Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: NTom Rini <trini@ti.com>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>

We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R
Signed-off-by: NTom Rini <trini@ti.com>

We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R
Signed-off-by: NTom Rini <trini@ti.com>

OMAP4/5 had an empty arch_cpu_init() so drop that along with
CONFIG_ARCH_CPU_INIT
Signed-off-by: NTom Rini <trini@ti.com>

This is only used on !CONFIG_GENERIC_MMC which is false here.
Signed-off-by: NTom Rini <trini@ti.com>

As ttyS0 is no longer valid for newer OMAP kernels, and pandora serial
cables are not widespread, simply drop console argument. This should
allow booting old and new kernels with default arguments, and those who
need serial can use a boot script on SD card.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>

Update pandora's GPIO setup code with these changes:
- convert to gpiolib
- set up dual voltage GPIOs to match supply of 1.8V by clearing VMODE1
- add GPIO_IO_PWRDNZ configuration for DM3730 variation of pandora
  (required to enable GPIO 126, 127, and 129 I/O cells in DM3730)
- add wifi reset pulse as recommended by wifi chip's manufacturer
- drop configuration of GPIOs that u-boot doesn't need
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>

DM3730 needs some additional pin mux configuration for GPIOs
126-129 to work, add it.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>

This rule confirms that if we're on ARM and we have enabled THUMB builds
that we have a new enough toolchain to produce a working binary.

Changes in v2:
- Switch to ALL-$(CONFIG_SYS_THUMB_BUILD) in arch/arm/config.mk (Mike F)
- Simplfy checkthumb test after doing the above
Signed-off-by: NTom Rini <trini@ti.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Added from Linux - commit fde7d9049e55ab85a390be7f415d74c9f62dd0f9
Signed-off-by: NTom Rini <trini@ti.com>

Signed-off-by: NAneesh V <aneesh@ti.com>

Avoid using __attribute__ ((__packed__)) unless it's
absolutely necessary. "packed" will remove alignment
requirements for the respective objects and may cause
alignment issues unless alignment is also enforced
using a pragma.

Here, these packed attributes were causing alignment
faults in Thumb build.
Signed-off-by: NAneesh V <aneesh@ti.com>

Enable -march=armv7-a for armv7 platforms if the tool-chain
supports it. This in turn results in Thumb-2 code generated
for these platforms if CONFIG_SYS_THUMB_BUILD is enabled.
Signed-off-by: NAneesh V <aneesh@ti.com>

Enable Thumb build and ARM-Thumb interworking based on the new
config flag CONFIG_SYS_THUMB_BUILD
Signed-off-by: NAneesh V <aneesh@ti.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.
Signed-off-by: NAneesh V <aneesh@ti.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

This will add ARM specific over-rides for the defines
from linux/linkage.h
Signed-off-by: NAneesh V <aneesh@ti.com>
Tested-by: NMike Frysinger <vapier@gentoo.org>

Warm reset is not functional in case of omap5430ES1.0.
So override the weak reset_cpu function to use
cold reset instead.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>

The reset.S has the function to do a warm reset on OMAP
based socs. Moving this to a reset.c file so that this
acts a common layer to add any reset related functionality
for the future.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>

Save env to eMMC
Signed-off-by: NBalaji T K <balajitk@ti.com>

Add omap5 pbias configuration for mmc1/sd lines
and set voltage for sd data i/o lines
Signed-off-by: NBalaji T K <balajitk@ti.com>

palmas/TWL6035 is power IC for omap5 evm boards
Signed-off-by: NBalaji T K <balajitk@ti.com>

In OMAP5 Boot device mode of 6 and 7 should be mapped to mmc2/eMMC
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

PD_TIM bit field which specifies the power down timing is defined
to occupy bits 8-11, where as it is actually from 12-15 bits.
So correcting this.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>

The ddr part name used in OMAP5 ES1.0 soc is a SAMSUNG part and
not a ELPIDA part. So change this.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>

Adding the nessecary changes for OMAP5430 ES1.0 silicon.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>

Add support to identify the device as GP/EMU/HS.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>

Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>

The full internal SRAM of size 128kb is public in the case of OMAP5 soc.
So change the base address accordingly.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>

The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>