- 17 12月, 2013 1 次提交
-
-
由 Fabio Estevam 提交于
The pmic_init() function has the I2C or SPI bus number that is connected to the PMIC. Instead of passing I2C_PMIC, explicitly pass the I2C bus number via I2C_x definition. The motivation for doing this is to avoid people just doing a copy and paste of I2C_PMIC into their board file when another I2C bus is actually used to interface to their PMIC. This also makes more obvious which is the I2C bus connected to the PMIC, without having to search in the source code for the meaning of the 'I2C_PMIC' number. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
- 28 11月, 2013 5 次提交
-
-
由 Giuseppe Pagano 提交于
uDoo uses APX823-31W5 watchdog chip. Timeout is about 1.2 seconds. To disabled watchdog during kernel boot, WDI pin of that chip needs to be in "high impedance" state. I.mx6 gpio configuration does not contemplate tristate, so pin is set as input in high impedance. Signed-off-by: NGiuseppe Pagano <giuseppe.pagano@seco.com> Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
-
由 Giuseppe Pagano 提交于
Add Ethernet and networking support on uDoo board (FEC +phy Micrel KSZ9031). Ethernet speed is currently limited to 10/100Mbps. Signed-off-by: NGiuseppe Pagano <giuseppe.pagano@seco.com> Tested-by: NFabio Estevam <fabio.estevam@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
-
由 Giuseppe Pagano 提交于
Previous uDoo configuration adopts register settings for DDR3, clock, muxing, etc. taken from Nitrogen6x. uDoo schematics is rather different from that board, and it needs customized setting for most of the registers. All this changes can be considered atomical since it is part of initial support of the board. Patch changes uDoo configuration files path to a specific one, and adopt optimized value for every configured register. Signed-off-by: NGiuseppe Pagano <giuseppe.pagano@seco.com> Tested-by: NFabio Estevam <fabio.estevam@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
mx6sabre board has a m25p32 SPI NOR connected to ECSPI1 port. Add support for it. This patch allows the SPI NOR flash to be succesfully detected: => sf probe SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Currently HDMI splash screen is selected by default on mx6sabresd boards. As LVDS is also enabled, this causes incorrect colors to be displayed im the LVDS panel. Fix this by selecting the LVDS panel as the default splash output and only keep HDMI or LVDS turned on at the same time. Acked-by: NLiu Ying <Ying.Liu@freescale.com> Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 27 11月, 2013 6 次提交
-
-
由 Fabio Estevam 提交于
There is no need to pass p->bus differently when the PMIC is connected via SPI or via I2C. Handle the both cases in the same way. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
On efikamx board the PMIC is connected via SPI interface, so it does not make sense to pass I2C_PMIC into the pmic_init() interface. Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
On mx31pdk board the PMIC is connected via SPI interface, so it does not make sense to pass I2C_PMIC into the pmic_init() interface. Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
On mx51evk board the PMIC is connected via SPI interface, so it does not make sense to pass I2C_PMIC into the pmic_init() interface. Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Eric Nelson 提交于
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
-
由 Fabio Estevam 提交于
OCOTP driver is currently selected via CONFIG_MXC_OCOTP option. Remove the old OCOTP related options, as they are not used anymore. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NEric Nelson <eric.nelson@boundarydevices.com>
-
- 21 11月, 2013 1 次提交
-
-
由 Marek Vasut 提交于
The fec_halt() never free'd both RX and TX DMA descriptors that were allocated in fec_init(), nor did it free the RX buffers. Rework the FEC driver so that these descriptors and buffers are allocated only once in fec_probe(). Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
-
- 13 11月, 2013 11 次提交
-
-
由 Eric Nelson 提交于
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
-
由 Eric Nelson 提交于
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
-
由 Eric Nelson 提交于
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
-
由 Eric Nelson 提交于
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
-
由 Eric Nelson 提交于
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
-
由 Stefan Roese 提交于
Since the titanium board is not a Freescale board, move its BSP code from the freescale board directory to the newly created barco board directory. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: NPeter Korsgaard <peter.korsgaard@barco.com>
-
由 Fabio Estevam 提交于
When cpu_eth_init() fails we should not return success. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NStefan Roese <sr@denx.de>
-
由 Fabio Estevam 提交于
When cpu_eth_init() fails we should not return success. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
If ipuv3_fb_init() fails, we should return the error immediately. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Michael Heimpold 提交于
Setting the direction and an output value should be done by 1) set the desired output value, 2) switch to output. If this is done in the inverse order, there can be a glitch on the GPIO line. This patch fixes this by using the order as described above. Signed-off-by: NMichael Heimpold <mhei@heimpold.de> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
There is no real benefit in adding the board name into U-boot's prompt, so remove the custom CONFIG_SYS_PROMPT definitions so that the standard "=> " prompt is used across FSL boards. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 12 11月, 2013 9 次提交
-
-
由 Samuel Egli 提交于
- dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: NSamuel Egli <samuel.egli@siemens.com> Signed-off-by: NPascal Bach <pascal.bach@siemens.com> Signed-off-by: NRoger Meier <r.meier@siemens.com> Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
-
由 Heiko Schocher 提交于
add the possibility to set the bcdDevice number board specific. Therefore the weak function g_dnl_get_board_bcd_device_number() is introduced. Used on the siemens boards. Signed-off-by: NHeiko Schocher <hs@denx.de> Acked-by: NLukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
由 Tom Rini 提交于
Some am33xx boards may not use the RTC block for bootcount (as it may not be wired up for the board) and use some other facility. So add another symbol for the bootcount driver for the IP block. Acked-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NTom Rini <trini@ti.com>
-
由 Igor Grinberg 提交于
Switch to using the generic gpio_led driver instead of the private to cm_t35 board led implementation. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
-
由 Andrew Bradford 提交于
Commit f6d1f6e4 broke selection of UARTs other than UART0 for am335x_evm configurations by setting CONS_INDEX to 1 for all configurations. Revert the CONS_INDEX changes. Signed-off-by: NAndrew Bradford <andrew@bradfordembedded.com>
-
由 Matt Porter 提交于
Update my email address as ti814x_evm maintainer to save people some frustrating bounces and non-response. Signed-off-by: NMatt Porter <matt.porter@linaro.org>
-
由 Heiko Schocher 提交于
As http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast states: "Initialize devices only when they are needed within U-Boot" enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is enabled. Enable this in ti_am335x_common.h, so all boards in mainline should work as before. Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
-
由 Heiko Schocher 提交于
If no softreset save registers are found on the hardware "bootcount" is stored in the environment. To prevent a saveenv on all reboots, the environment variable "upgrade_available" is introduced. If "upgrade_available" is 0, "bootcount" is always 0 therefore no need to save the environment on u-boot boot, if "upgrade_available" is 1 "bootcount" is incremented in the environment and environment gets written on u-boot start. So the Userspace Applikation must set the "upgrade_available" and "bootcount" variable to 0 (for example with fw_setenv), if a boot was successfully. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 10 11月, 2013 1 次提交
-
-
由 Albert ARIBAUD 提交于
Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
-
- 09 11月, 2013 6 次提交
-
-
-
由 Rob Herring 提交于
Convert sandbox to use common time functions. Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
由 Rob Herring 提交于
A weak annotation is needed in order to prevent link errors when get_ticks is overridden. This fixes sandbox build. Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
由 Suriyan Ramasami 提交于
Netconsole loses the second character when used as input by either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX Before a nc_send_packet() to echo the input, a check is done to see if nc_ether is valid. If its not, it waits for an arp request and then sends the packet (which contains the first character of line to be displayed as output). As part of reaping the arp request, the second character is consumed. We protect this by making the call to NetLoop(NETCONS) between input_recursion. Signed-off-by: NSuriyan Ramasami <suriyan.r@gmail.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Axel Lin 提交于
Staticize local functions in s5p serial driver. Signed-off-by: NAxel Lin <axel.lin@ingics.com> Acked-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Pierre Aubert 提交于
The env export command doesn't export the first variable of the list since commit 5a31ea04 "env grep" - reimplement command using hexport_r() Signed-off-by: NPierre Aubert <p.aubert@staubli.com>
-