- 30 3月, 2010 1 次提交
-
-
由 Kumar Gala 提交于
Use the same code between primary and secondary cores to init the L1 cache. We were not enabling cache parity on the secondary cores. Also, reworked the L1 cache init code to match the e500mc L2 init code that first invalidates the cache and locks. Than enables the cache and makes sure its enabled before continuing. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 28 3月, 2010 5 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
The ml300 board has a number of issues, but nobody cares about this long-orphaned board any more. Remove it. Signed-off-by: NWolfgang Denk <wd@denx.de> Acked-by: NMichal Simek <monstr@monstr.eu>
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
The restructuring of the mkimage command in commit 89a4d6b1 ("tools: mkimage: split code into core, default and FIT image specific") introduced a bug that caused mkimage to segfault when run without "-n name" option. Initialize the imagename entry to prevent that. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
-
- 25 3月, 2010 1 次提交
-
-
由 Renato Andreola 提交于
With old configuration it could happen tout=0 if CONFIG_SYS_HZ<1000. Signed-off-by: NRenato Andreola <renato.andreola@imagos.it> Signed-off-by: NAlessandro Rubini <rubini@gnudd.com> Signed-off-by: NThomas Chou <thomas@wytron.com.tw> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 24 3月, 2010 4 次提交
-
-
由 Rupjyoti Sarmah 提交于
440EPx fixed bootstrap options A, B, D, and E sets PLL FWDVA to a value = 1. This results in the PLLOUTB being greater than the CPU clock frequency resulting unstable 440EPx operation resulting in various software hang conditions. This patch reprograms the FWDVA satisfying the requirement of setting FWDVB to a value greater than 1 while using one of the four deafult bootstrap options. Signed-off-by: NRupjyoti Sarmah <rsarmah@amcc.com> Acked-by : Victor Gallardo <vgallardo@appliedmicro.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
-
由 Matthias Fuchs 提交于
The soft-i2c code for AT91 defines I2C_SOFT_DECLARATIONS for direct access by dereferencing a pio pointer. The OTC570 platform uses the AT91 gpio API so it does not need the pio variable. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
-
由 Alessandro Rubini 提交于
Support for 16bpp was supposed to be in the code but was not working. This makes it work and has been tested in the nhk8815 board. Signed-off-by: NAlessandro Rubini <rubini@unipv.it> Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 23 3月, 2010 3 次提交
-
-
由 Wolfgang Denk 提交于
Update CHANGELOG Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Matthias Kaehlcke 提交于
ep93xx timer: Make get_ticks() return a value in CONFIG_SYS_HZ resolution, as announced by get_tbclk() Signed-off-by: NMatthias Kaehlcke <matthias@kaehlcke.net>
-
由 Matthias Kaehlcke 提交于
ep93xx timer: Use 64-bit values in usecs_to_ticks() in order to avoid overflows in intermediate values Signed-off-by: NMatthias Kaehlcke <matthias@kaehlcke.net>
-
- 22 3月, 2010 8 次提交
-
-
由 Asen Dimov 提交于
Signed-off-by: NAsen Dimov <dimov@ronetix.at>
-
由 Jeff Angielski 提交于
The crc table was being built as little endian for big endian targets. This would cause fw_printenv to always fail with "Warning: Bad CRC, using default environment" messages. Signed-off-by: NJeff Angielski <jeff@theptrgroup.com> Acked-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
-
由 Anatolij Gustschin 提交于
Fix warnings while compiling with CONFIG_VIDEO enabled: diu.c: In function 'video_hw_init': diu.c:158: warning: 'return' with no value, in function returning non-void diu.c:162: warning: format '%ld' expects type 'long int', but argument 6 has type 'int' diu.c:162: warning: format '%ld' expects type 'long int', but argument 7 has type 'int' Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
If a board uses cfb_console driver and splash image and also defines CONFIG_SILENT_CONSOLE, the user is locked out even if "silent" is not set. It is not possible to get any output, neither on vga console device nor on serial console after redirecting the output to the serial console, since the GD_FLG_SILENT flag remains set. Fix the problem by redirecting the output from frame buffer to serial console if splashimage is used. Only suppress the output if "silent" environment variable was set and don't set the GD_FLG_SILENT flag arbitrarily. Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Thomas Weber 提交于
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;' Signed-off-by: NThomas Weber <swirl@gmx.li> Add some more: neither Makefile nor config.mk need execute permissions. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Stefano Babic 提交于
Some registers of the mxcmmc driver were accessed using 16 bit accessor functions, because only the LSB is significant. This is not needed and generates warnings. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Wolfgang Denk 提交于
So far, TFTP negotiated a fixed retransmission timeout of 5 seconds. In some cases (busy networks, slow TFTP servers) this caused very slow transfers. A new environment variable "tftptimeout" allows to set this timeout. Lowering this value may make downloads succeed faster in networks with high packet loss rates or with unreliable TFTP servers. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Wolfgang Denk 提交于
Signed-off-by: NFUJITA Kazutoshi <fujita@soum.co.jp> Signed-off-by: <wd@denx.de> Acked-by: NStefan Roese <sr@denx.de>
-
- 21 3月, 2010 1 次提交
-
-
由 Frans Meulenbroeks 提交于
This patch removes the \n after the help message for mmcinfo. This resulted in an empty line being displayed after the mmcinfo line when the help command was given. Signed-off-by: NFrans Meulenbroeks <fransmeulenbroeks@gmail.com>
-
- 17 3月, 2010 2 次提交
-
-
由 Renato Andreola 提交于
Signed-off-by: NScott McNutt <smcnutt@psyent.com>
-
由 Thomas Chou 提交于
Signed-off-by: NScott McNutt <smcnutt@psyent.com>
-
- 14 3月, 2010 3 次提交
-
-
-
由 Mike Frysinger 提交于
The new zlib code wants asm/unaligned.h, so have the Blackfin version pull in the asm-generic/unaligned.h. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
This is based on the asm-arm/unaligned.h, but made generic so all arches that cannot do unaligned accesses can utilize it. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 13 3月, 2010 4 次提交
-
-
由 Matthias Weisser 提交于
If a splashscreen is used the console scrolling used the scroll size as needed when a logo was displayed. This patch sets the scroll size to the whole screen if a splashscreen is shown. Signed-off-by: NMatthias Weisser <matthias.weisser@graf-syteco.de>
-
由 Wolfgang Denk 提交于
Coding style cleanup, update CHANGELOG. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Building examples/standalone/eepro100_eeprom triggers this error: In file included from include/common.h:629, from eepro100_eeprom.c:24: include/net.h: In function 'NetReadIP': include/net.h:430: warning: implicit declaration of function 'memcpy' eepro100_eeprom.c: At top level: eepro100_eeprom.c:81: error: conflicting types for 'memcpy' include/net.h:430: error: previous implicit declaration of 'memcpy' was here Fix this. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 12 3月, 2010 8 次提交
-
-
由 Detlev Zundel 提交于
This code has compile problems and the company does not even exist any more. So we take the liberty to drop support for it. Signed-off-by: NDetlev Zundel <dzu@denx.de> CC: Wolfgang Denk <wd@denx.de> CC: Ben Warren <biggerbadderben@gmail.com>
-
由 Kumar Gala 提交于
The 36-bit build exceeds the 512k size we have. Removing FIT type image support allows us to fit and we dont really use it. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Michael Zaidman 提交于
Signed-off-by: NMichael Zaidman <michael.zaidman@gmail.com>
-
由 Anatolij Gustschin 提交于
The length of configured MTDPARTS_DEFAULT string could be greater than console printbuffer size. Replace printf() by puts() to avoid potential buffer overflows. Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Frans Meulenbroeks 提交于
This patch corrects small mistake in the register list in doc/README.mpc8536ds. These registers are 32 bits and this one starts at ....c not ....e When using the ...c address I can boot from sd, when using the ...e address I cannot. Signed-off-by: NFrans Meulenbroeks <fransmeulenbroeks@gmail.com> Acked-by: NHu Mingkai <B21284@freescale.com>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Also enable support for CONFIG_HWCONFIG because we use this for configuring if this hardware has a FEC or not. syntax: hwconfig=fec:on if hardware has an fec hwconfig=fec:off if hardware has no fec Signed-off-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Heiko Schocher 提交于
Also use hwconfig to configure whether the board has a FEC or not. We then can adjust the DTS to tell Linux if there is a FEC present. syntax: hwconfig=fec:on if hardware has a FEC hwconfig=fec:off if hardware has no FEC Signed-off-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NWolfgang Denk <wd@denx.de>
-