- 20 10月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 9月, 2018 1 次提交
-
-
由 Ran Wang 提交于
Signed-off-by: NRan Wang <ran.wang_1@nxp.com> [York S: revised subject line and removed commit message] Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 18 8月, 2018 2 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: NAdam Ford <aford173@gmail.com> Acked-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 17 8月, 2018 1 次提交
-
-
由 Tom Rini 提交于
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 07 5月, 2018 1 次提交
-
-
由 Tom Rini 提交于
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 4月, 2018 2 次提交
-
-
由 Mario Six 提交于
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 16 3月, 2018 1 次提交
-
-
由 Tom Rini 提交于
This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 24 2月, 2018 2 次提交
-
-
由 Adam Ford 提交于
With the contents of config_distro_defaults.h migrated to Kconfig, we can remove this header file completely Signed-off-by: NAdam Ford <aford173@gmail.com>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the current set of options we have in Kconfig. We will need to have some options available for SPL and !SPL_FRAMEWORK so this is important. In a few cases we re-order existing options so that we have less escapes from the SPL_FRAMEWORK guard. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 1月, 2018 1 次提交
-
-
由 Ran Wang 提交于
Rename to USB_EHCI_FSL, use Kconfig to select ehci accordingly. Signed-off-by: NRan Wang <ran.wang_1@nxp.com>
-
- 07 12月, 2017 1 次提交
-
-
由 Vinitha Pillai-B57223 提交于
Add fall back option, to boot from NOR/QSPI/SD for LS1043, LS1046, LS1021 in case of distro boot failure. For LS1046, add kernel validation in case of secure boot in sd_bootcmd and qspi_bootcmd. For LS1043 and LS1021, add kernel validation in case of secure boot in sd_bootcmd, qspi_bootcmdand nor_bootcmd. Signed-off-by: NVinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 16 11月, 2017 1 次提交
-
-
由 Shengzhou Liu 提交于
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 27 10月, 2017 3 次提交
-
-
由 Ran Wang 提交于
Because COMFIG_DM_USB has been enabled and will not use it anymore. Signed-off-by: NRan Wang <ran.wang_1@nxp.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Ran Wang 提交于
use Kconfig to select xhci accordingly. Signed-off-by: NRan Wang <ran.wang_1@nxp.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Ran Wang 提交于
Use Kconfig to select QE-HDLC and USB pin-mux. Signed-off-by: NRan Wang <ran.wang_1@nxp.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 04 9月, 2017 4 次提交
-
-
由 Thomas Petazzoni 提交于
This commit removes definitions of CONFIG_SYS_BARGSIZE defined to be equal to CONFIG_SYS_CBSIZE in numerous configuration files. We remove such definitions in two situations: - CONFIG_SYS_CBSIZE is otherwise not defined in the board configuration file, which means the default value of CONFIG_SYS_CBSIZE == 256 applies. In this case, the default value of CONFIG_SYS_BARGSIZE == 512 (common/image.c) is suitable, as it is larger. - CONFIG_SYS_CBSIZE is defined in the board configuration file, but to a value equal or less than 512. In this case, the default value of CONFIG_SYS_BARGSIZE == 512 (common.image.c) is suitable, as it is equal or larger. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Thomas Petazzoni 提交于
Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Thomas Petazzoni 提交于
Now that the fallback value of CONFIG_SYS_PBSIZE in include/config_fallbacks.h has been adjusted, remove its definition from a large number of board configuration files. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Thomas Petazzoni 提交于
Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: NTom Rini <trini@konsulko.com> [trini: Drop <config.h> from stih410-b2260.h] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 8月, 2017 1 次提交
-
-
由 Sam Protsenko 提交于
Also introduce CONFIG_USE_BOOTARGS option so we can control if CONFIG_BOOTARGS defined at all. Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org> [trini: Resync r8a779[56]_ulcb, various ls10xx targets] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 13 8月, 2017 1 次提交
-
-
由 Philipp Tomsich 提交于
With the hierarchical defaults set up, we remove these from the header files. To do so, I've run moveconfig on SPL_LDSCRIPT and this commits the changes. Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
- 12 8月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_PCI Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
- 09 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Reviewed-by: NJoe Hershberger <joe.hershberger@ni.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 8月, 2017 1 次提交
-
-
由 Alexandru Gagniuc 提交于
Signed-off-by: NAlexandru Gagniuc <alex.g@adaptrum.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 01 8月, 2017 2 次提交
-
-
由 Sumit Garg 提交于
Enable validation of boot.scr script prior to its execution dependent on "secureboot" flag in environment. Disable fall back option to qspi boot in case of secure boot. Also enable "secureboot=y" flag in environment for ARM based platforms instead of bootcmd. Signed-off-by: NSumit Garg <sumit.garg@nxp.com> Tested-by: NVinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Alison Wang 提交于
This patch includes common config_distro_defaults.h and config_distro_bootcmd.h for u-boot enviroments to support distro boot which automatically scan boot.scr from storage devices(e.g. SD/USB/SATA/SCSI disk) and execute autoboot script on LS1021ATWR board. Signed-off-by: NShengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: NAlison Wang <alison.wang@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 29 7月, 2017 1 次提交
-
-
由 Bin Meng 提交于
Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS, remove it in all boards' config files. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NStefan Roese <sr@denx.de> Tested-by: NStefan Roese <sr@denx.de>
-
- 26 7月, 2017 3 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_ENV_IS_IN_SPI_FLASH Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_ENV_IS_IN_FLASH Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 02 6月, 2017 1 次提交
-
-
由 Zhao Qiang 提交于
modify u_qe_init to upload QE firmware from SD card when it is SD boot Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 24 5月, 2017 1 次提交
-
-
由 Alison Wang 提交于
This patch is to adjust the memory mapping for FLash/SD card on LS1021AQDS and LS1021ATWR, such as U-Boot start address on serial Flash, QE firmware load address and environment address. Signed-off-by: NAlison Wang <alison.wang@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 23 5月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_HASH Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com> [trini: Rework slightly, enable on some boards again] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 22 5月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Commit 94e3c8c4 ("crypto/fsl - Add progressive hashing support using hardware acceleration.") created entries for CONFIG_SHA1, CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL. However, no defconfig has migrated to it. Complete the move by first adding additional logic to various Kconfig files to select this when required and then use the moveconfig tool. In many cases we can select these because they are required to implement other drivers. We also correct how we include the various hashing algorithms in SPL. This commit was generated as follows (after Kconfig additions): [1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL [2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL Note: We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously because there is dependency between them. Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: Priyanka Jain <Priyanka.Jain@freescale.com> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Cc: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Chander Kashyap <k.chander@samsung.com> Cc: Steve Rae <steve.rae@raedomain.com> Cc: Dirk Eibach <eibach@gdsys.de> Cc: Feng Li <feng.li_2@nxp.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Sumit Garg <sumit.garg@nxp.com> Cc: Mingkai Hu <Mingkai.Hu@freescale.com> Cc: York Sun <york.sun@nxp.com> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Akshay Saraswat <akshay.s@samsung.com> Cc: Heiko Schocher <hs@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 16 5月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig. For a few SoCs, imply or default y this if USB is enabled. In some cases we had not already migrated to CONFIG_USB so do that as well. Cc: Marek Vasut <marex@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NMarek Vasut <marex@denx.de>
-
- 15 5月, 2017 1 次提交
-
-
由 Tom Rini 提交于
In order to be able to migrate the various SoC EHCI CONFIG options we first need to finish the switch from CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD. Cc: Marek Vasut <marex@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NMarek Vasut <marex@denx.de>
-