Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 大约 4 年

通知 14
Star 8
Fork 2
K
kernel_linux
切换分支/标签
  1. 02 4月, 2013 6 次提交
  3. 09 11月, 2012 2 次提交
    • A
      ARM: OMAP2+: gpmc: generic timing calculation · 246da26d
      由 Afzal Mohammed 提交于 
      Presently there are three peripherals that gets it timing
by runtime calculation. Those peripherals can work with
frequency scaling that affects gpmc clock. But timing
calculation for them are in different ways.

Here a generic runtime calculation method is proposed. Input
to this function were selected so that they represent timing
variables that are present in peripheral datasheets. Motive
behind this was to achieve DT bindings for the inputs as is.
Even though a few of the tusb6010 timings could not be made
directly related to timings normally found on peripherals,
expressions used were translated to those that could be
justified.

There are possibilities of improving the calculations, like
calculating timing for read & write operations in a more
similar way. Expressions derived here were tested for async
onenand on omap3evm (as vanilla Kernel does not have omap3evm
onenand support, local patch was used). Other peripherals,
tusb6010, smc91x calculations were validated by simulating
on omap3evm.

Regarding "we_on" for onenand async, it was found that even
for muxed address/data, it need not be greater than
"adv_wr_off", but rather could be derived from write setup
time for peripheral from start of access time, hence would
more be in line with peripheral timings. With this method
it was working fine. If it is required in some cases to
have "we_on" same as "wr_data_mux_bus" (i.e. greater than
"adv_wr_off"), another variable could be added to indicate
it. But such a requirement is not expected though.

It has been observed that "adv_rd_off" & "adv_wr_off" are
currently calculated by adding an offset over "oe_on" and
"we_on" respectively in the case of smc91x. But peripheral
datasheet does not specify so and so "adv_rd(wr)_off" has
been derived (to be specific, made ignorant of "oe_on" and
"we_on") observing datasheet rather than adding an offset.
Hence this generic routine is expected to work for smc91x
(91C96 RX51 board). This was verified on smsc911x (9220 on
OMAP3EVM) - a similar ethernet controller.

Timings are calculated in ps to prevent rounding errors and
converted to ns at final stage so that these values can be
directly fed to gpmc_cs_set_timings(). gpmc_cs_set_timings()
would be modified to take ps once all custom timing routines
are replaced by the generic routine, at the same time
generic timing routine would be modified to provide timings
in ps. struct gpmc_timings field types are upgraded from
u16 => u32 so that it can hold ps values.

Whole of this exercise is being done to achieve driver and
DT conversion. If timings could not be calculated in a
peripheral agnostic way, either gpmc driver would have to
be peripheral gnostic or a wrapper arrangement over gpmc
driver would be required.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
      246da26d
    • A
      ARM: OMAP2+: gpmc: handle additional timings · 559d94b0
      由 Afzal Mohammed 提交于 
      Configure busturnaround, cycle2cycledelay, waitmonitoringtime,
clkactivationtime in gpmc_cs_set_timings(). This is done so
that boards can configure these parameters of gpmc in Kernel
instead of relying on bootloader. Also configure bool type
timings like extradelay.

This needed change to the existing users that were configuring
clk activation time and extra delay by directly writing to
registers. Thanks to Tony for making me aware of users of clk
activation and being kind enough to test the modified one.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
      559d94b0
  5. 15 10月, 2012 4 次提交
  7. 31 8月, 2012 2 次提交
  9. 14 5月, 2012 1 次提交
    • I
      ARM: OMAP3: gpmc: add BCH ecc api and modes · 8d602cf5
      由 Ivan Djelic 提交于 
      This patch adds a simple BCH ecc computation api, similar to the
existing Hamming ecc api. It is intended to be used by the MTD layer.
It implements the following features:

- support 4-bit and 8-bit ecc computation
- do not protect user bytes in spare area, only data area is protected
- ecc for an erased NAND page (0xFFs) is also a sequence of 0xFFs

This last feature is obtained by adding a constant polynomial to
the hardware computed ecc. It allows to correct bitflips in blank pages
and is extremely useful to support filesystems such as UBIFS, which expect
erased pages to contain only 0xFFs.

This api has been tested on an OMAP3630 board.

Artem: The OMAP maintainer Tony Lindgren gave us his blessing for merging
this patch via the MTD tree.
Signed-off-by: NIvan Djelic <ivan.djelic@parrot.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
      8d602cf5
  11. 31 3月, 2011 1 次提交
  13. 18 2月, 2011 4 次提交
  15. 22 12月, 2010 1 次提交
  17. 02 8月, 2010 2 次提交
  19. 16 2月, 2010 2 次提交
    • V
      omap3: SDP: Introducing 'board-sdp-flash.c' for flash init · c2798e93
      由 Vimal Singh 提交于 
      This patch adds 'board-sdp-flash.c', which could be utilized
by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp).

This file does initialization for all three flash devices present
in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number
dynamically using switch setting information (S8: 1-4).
This also expects partition information from core board files (for
ex: board-3430sdp.c). Which allows to choose different default
partitions for different boards.

A new structure is created for this purpose: 'flash_partitions'
in 'mach/board-sdp.h'. This has two members:
1. struct mtd_partition *parts
2. int nr_parts

A board file is expected to fill this structure and pass it to
'sdp-flsash-init'. Partition information should be passed in
structure array of 'flash_partitions'. Partition information should
be passed in below sequence in array:
NOR
OneNAND
NAND
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      c2798e93
    • F
      omap2/3/4: gpmc: avoid section definitions on headers · 2586ef0d
      由 Felipe Balbi 提交于 
      trivial patch, no functional changes.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      2586ef0d
  21. 12 12月, 2009 1 次提交
  23. 12 11月, 2009 1 次提交
  25. 21 10月, 2009 1 次提交
    • T
      omap: headers: Move remaining headers from include/mach to include/plat · ce491cf8
      由 Tony Lindgren 提交于 
      Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.

This was done with:

#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"

for header in $headers; do
	old="#include <mach\/$header"
	new="#include <plat\/$header"
	for dir in $omap_dirs; do
		find $dir -type f -name \*.[chS] | \
			xargs sed -i "s/$old/$new/"
	done
	find drivers/ -type f -name \*omap*.[chS] | \
		xargs sed -i "s/$old/$new/"
	for file in $other_files; do
		sed -i "s/$old/$new/" $file
	done
done

for header in $(ls $mach_dir_old/*.h); do
	git mv $header $plat_dir_new/
done
Signed-off-by: NTony Lindgren <tony@atomide.com>
      ce491cf8
  27. 20 9月, 2009 1 次提交
  29. 09 2月, 2009 1 次提交
  31. 09 10月, 2008 1 次提交
    • S
      ARM: OMAP3: Add minimal omap3430 support · cc26b3b0
      由 Syed Mohammed, Khasim 提交于 
      Add minimal omap3430 support based on earlier patches from
Syed Mohammed Khasim. Also merge in omap34xx SRAM support
from Karthik Dasu and use consistent naming for sram init
functions.

Also do following changes that make 34xx support usable:

- Remove unused sram.c functions for 34xx

- Rename IRQ_SIR_IRQ to INTCPS_SIR_IRQ and define it locally
  in entry-macro.S

- Update mach-omap2/io.c to support 2420, 2430, and 34xx

- Also merge in 34xx GPMC changes to add fields wr_access and
  wr_data_mux_bus from Adrian Hunter

- Remove memory initialization call omap2_init_memory() until
  until more generic memory initialization patches are posted.
  It's OK to rely on bootloader initialization until then.
Signed-off-by: NSyed Mohammed, Khasim <khasim@ti.com>
Signed-off-by: Karthik Dasu<karthik-dp@ti.com>
Signed-off-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      cc26b3b0
  33. 06 10月, 2008 2 次提交
  35. 07 8月, 2008 1 次提交
  37. 21 9月, 2007 2 次提交
  39. 09 5月, 2007 2 次提交
  41. 25 9月, 2006 1 次提交
  43. 27 6月, 2006 1 次提交