提交 · d63fa0dc1a3636816260bc507e59e168e423f150 · openeuler / raspberrypi-kernel

22 11月, 2012 3 次提交

drm/i915: don't limit Haswell CRT encoder to pipe A · d63fa0dc

由 Paulo Zanoni 提交于 11月 20, 2012

This is a full revert of 59c859d6:
    drm/i915: account for only one PCH receiver on Haswell

Now that the PCH code is fixed to be able use the only PCH transcoder
independently of the pipe and CPU transcoder, we can revert this.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Resolve conflict due to the rebasing of dinq on top of
drm-next.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

d63fa0dc

drm/i915: Flush outstanding unpin tasks before pageflipping · b4a98e57

由 Chris Wilson 提交于 11月 01, 2012

If we accumulate unpin tasks because we are pageflipping faster than the
system can schedule its workers, we can effectively create a
pin-leak. The solution taken here is to limit the number of unpin tasks
we have per-crtc and to flush those outstanding tasks if we accumulate
too many. This should prevent any jitter in the normal case, and also
prevent the hang if we should run too fast.

Note: It is important that we switch from the system workqueue to our
own dev_priv->wq since all work items on that queue are guaranteed to
only need the dev->struct_mutex and not any modeset resources. For
otherwise if we have a work item ahead in the queue which needs the
modeset lock (like the output detect work used by both polling or
hpd), this work and so the unpin work will never execute since the
pageflip code already holds that lock. Unfortunately there's no
lockdep support for this scenario in the workqueue code.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46991Reported-and-tested-by: NTvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Added note about workqueu deadlock.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56337Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

b4a98e57

drm/i915: drop buggy write to FDI_RX_CHICKEN register · 607a6f7a

由 Daniel Vetter 提交于 11月 14, 2012

Jani Nikula noticed that the parentheses are wrong and we & the bit
with the register address instead of the read-back value. He sent a
patch to correct that.

On second look, we write the same register in the previous line, and
the w/a seems to be to set FDI_RX_PHASE_SYNC_POINTER_OVR to enable the
logic, then keep always set FDI_RX_PHASE_SYNC_POINTER_OVR and toggle
FDI_RX_PHASE_SYNC_POINTER_EN before/after enabling the pc transcoder.

So the right things seems to be to simply kill the 2nd write.

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Dropped a bogus ~ from the commit message that somehow crept
in.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

607a6f7a

12 11月, 2012 37 次提交

drm/i915: Update load-detect failure paths for modeset-rework · 0e8b3d3e

由 Chris Wilson 提交于 11月 05, 2012

After the rework, intel_set_mode() became a little better behaved in
restoring the current mode if we failed to apply the requested modeline.
However, the failure path for load-detect would clobber the existing
state, leading to an oops during BIOS takeover on older machines.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

0e8b3d3e

drm/i915: Clear unused fields of mode for framebuffer creation · 0fed39bd

由 Chris Wilson 提交于 11月 05, 2012

With the stricter checks introduced in
commit ac911edae5960d7dccd9883f5fa5d25b591520de
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date:   Wed Oct 31 17:50:19 2012 +0200

    drm/i915: Check the framebuffer offset

(and friends), it became especially prudent to make sure that the
additional fields inside the mode were cleared before attempting to
create a framebuffer. In particular, the fb created for load detection
failed to do so and hence failed.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

0fed39bd

drm/i915: fix Haswell FDI link disable path · 1ad960f2

由 Paulo Zanoni 提交于 11月 01, 2012

This covers the "Disable FDI" section from the CRT mode set sequence.
This disables the FDI receiver and also the FDI pll.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

1ad960f2

drm/i915: fix Haswell FDI link training code · 04945641

由 Paulo Zanoni 提交于 11月 01, 2012

This commit makes hsw_fdi_link_train responsible for implementing
everything described in the "Enable and train FDI" section from the
Hawell CRT mode set sequence documentation. We completely rewrite
hsw_fdi_link_train to match the documentation and we also call it in
the right place.

This patch was initially sent as a series of tiny patches fixing every
little problem of the function, but since there were too many patches
fixing the same function it got a little difficult to get the "big
picture" of how the function would be in the end, so here we amended
all the patches into a single big patch fixing the whole function.

Problems we fixed:

  1 - Train Haswell FDI at the right time.

    We need to train the FDI before enabling the pipes and planes, so
    we're moving the call from lpt_pch_enable to haswell_crtc_enable
    directly.

    We are also removing ironlake_fdi_pll_enable since the PLL
    enablement on Haswell is completely different and is also done
    during the link training steps.

  2 - Use the right FDI_RX_CTL register on Haswell

    There is only one PCH transcoder, so it's always _FDI_RXA_CTL.
    Using "pipe" here is wrong.

  3 - Don't rely on DDI_BUF_CTL previous values

    Just set the bits we want, everything else is zero. Also
    POSTING_READ the register before sleeping.

  4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train

    According to the mode set sequence documentation, this is the
    right place. According to the FDI_RX_TUSIZE register description,
    this is the value we should set.

    Also remove the code that sets this register from the old
    location: lpt_pch_enable.

  5 - Properly program FDI_RX_MISC pwrdn lane values on HSW

  6 - Wait only 35us for the FDI link training

    First we wait 30us for the FDI receiver lane calibration, then we
    wait 5us for the FDI auto training time.

  7 - Remove an useless indentation level on hsw_fdi_link_train

    We already "break" when the link training succeeds.

  8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE

    When we fail the training.

  9 - Change Haswell FDI link training error messages

    We shouldn't call DRM_ERROR when still looping through voltage
    levels since this is expected and not really a failure. So in this
    commit we adjust the error path to only DRM_ERROR when we really
    fail after trying everything.

    While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since
    it's what we use everywhere.

  10 - Try each voltage twice at hsw_fdi_link_train

    Now with Daniel Vetter's suggestion to use "/2" instead of ">>1".
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Applied tiny bikesheds:
- mention in comment that we test each voltage/emphasis level twice
- realing arguments of the only untouched reg write, it spilled over
  the 80 char limit ...]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

04945641

J
drm/i915: remove HAS_eDP as unnecessary and inconsistent indirection · 547dc041
由 Jani Nikula 提交于 11月 02, 2012
```
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
```
547dc041

drm/i915: CPT+ pch transcoder workaround · 23670b32

由 Daniel Vetter 提交于 11月 01, 2012

We need to set the timing override chicken bit after fdi link training
has completed and before we enable the transcoder. We also have to
clear that bit again after disabling the pch transcoder.

See "Graphics BSpec: vol4g North Display Engine Registers [IVB],
Display Mode Set Sequence" and "Graphics BSpec: vol4h South Display
Engine Registers [CPT, PPT], South Display Engine Transcoder and FDI
Control, Transcoder Debug and DFT, TRANS_CHICKEN_2" bit 31:

"Workaround : Enable the override prior to enabling the transcoder.
Disable the override after disabling the transcoder."

While at it, use the _PIPE macro for the other TRANS_DP register.

v2: Keep the w/a as-is, but kill the original (but wrongly placed)
workaround introduced in

commit 3bcf603f
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Wed Jul 27 11:51:40 2011 -0700

    drm/i915: apply timing generator bug workaround on CPT and PPT

and

commit d4270e57
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Tue Oct 11 10:43:02 2011 -0700

    drm/i915: export a CPT mode set verification function

Note that this old code has unconditionally set the w/a, which might
explain why fdi link training sometimes silently fails, and especially
why the auto-train did not seem to work properly.

v3: Paulo Zanoni pointed out that this workaround is also required on
the LPT PCH. And Arthur Ranyan confirmed that this workaround is
requierd for all ports on the pch, not just DP: The important part
is that the bit is set whenever the pch transcoder is enabled, and
that it is _not_ set while the fdi link is trained. It is also
important that the pch transcoder is fully disabled, i.e. we have to
wait for bit 30 to clear before clearing the w/a bit.

Hence move to workaround into enable/disable_transcoder, where the pch
transcoder gets enabled/disabled.

v4: Whitespace changes dropped.

v5: Don't run the w/a on IBX, we only need it on CPT/PPT and LPT.

v6:
- resolve conflicts with Paulo's big hsw vga rework
- s/!IBX/CPT since hsw paths are now all separate, and Paulo's patch
  to implement the equivalent w/a for LPT is already merged.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v5)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v5)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

23670b32

drm/i915: drop unnecessary check from fdi_link_train code · 8f5718a6

由 Daniel Vetter 提交于 10月 31, 2012

They are all written for a specific north disaplay->pch combination.
So stop pretending otherwise.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

8f5718a6

drm/i915: move panel connectors to the front · 270b3042

由 Daniel Vetter 提交于 10月 27, 2012

This essentially reverts

commit cb0953d7
Author: Adam Jackson <ajax@redhat.com>
Date:   Fri Jul 16 14:46:29 2010 -0400

    drm/i915: Initialize LVDS and eDP outputs before anything else

simply because it doesn't scale: It misses SDVO and DVO panels,
and now with DDI encoders on haswell this is becoming unmanageable.

Instead we simply sort the connector list after everything is
set up.
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

270b3042

drm/i915: don't assert disabled FDI before disabling the FDI · ab4d966c