Several at91sam9 chips need the alternate reset procedure to be sure to halt
SDRAM smoothly before resetting the chip.
This is an extension of previous patch "Fix AT91SAM9G20 reset" to all chips
affected.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Generalize assembler reset routine to allow use on several at91sam9 chips.
This patch replace double definitions of SDRAM controller registers and RSTC
registers with use of classical header files.

For this rework, we remove the not needed icache flush as it is already
done in the calling function: arm_machine_restart().

Rename at91sam9g20_reset.S to generalize to several chips.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Preparing next patch with longer names
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

If the SDRAM is not cleanly shutdown before reset it can be left driving
the bus, which then stops the bootloader booting from NAND.
Signed-off-by: NPeter Horton <phorton@bitbox.co.uk>
[nicolas.ferre@atmel.com: change file header line order]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Board is a carrier board for Stamp9G20, with additional peripherals
for a building automation system
Signed-off-by: NPeter Gsellmann <pgsellmann@portner-elektronik.at>
[nicolas.ferre@atmel.com: remove machine_desc.io_pg_offst and .phys_io]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

* 'for-next' of git://android.git.kernel.org/kernel/tegra:
  spi: tegra: fix error setting on timeout
  spi: add spi_tegra driver
  tegra: harmony: enable PCI Express
  tegra: add PCI Express support
  tegra: add PCI Express clocks
  [ARM] tegra: Add APB DMA support
  [ARM] tegra: Add cpufreq support
  [ARM] tegra: common: Update common clock init table
  [ARM] tegra: clock: Add dvfs support, bug fixes, and cleanups
  [ARM] tegra: Add support for reading fuses
  [ARM] tegra: gpio: Add suspend and wake support
  [ARM] tegra: pinmux: add safe values, move tegra2, add suspend
  [ARM] tegra: add suspend and mirror irqs to legacy controller
  [ARM] tegra: Add legacy irq support
  [ARM] tegra: update iomap

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
  Blackfin: fix inverted anomaly 05000481 logic
  Blackfin: drop unused irq_panic()/DEBUG_ICACHE_CHECK
  Blackfin: ppi/spi/twi headers: add missing __BFP undef
  Blackfin: update defconfigs
  Blackfin: bfin_twi.h: start a common TWI header
  netdev: bfin_mac: push settings to platform resources

avoids derefencing an uninitialized pointer

Change-Id: Icf528441ae481e9f6f5ddc0be32c7c217fa49701
Signed-off-by: NErik Gilling <konkers@android.com>

* 'next' of git://git.monstr.eu/linux-2.6-microblaze: (42 commits)
  microblaze: Fix build with make 3.82
  fbdev/xilinxfb: Microblaze driver support
  microblaze: Support C optimized lib functions for little-endian
  microblaze: Separate library optimized functions
  microblaze: Support timer on AXI lite
  microblaze: Add support for little-endian Microblaze
  microblaze: KGDB little endian support
  microblaze: Add PVR for endians plus detection
  net: emaclite: Add support for little-endian platforms
  microblaze: trivial: Add comment for AXI pvr
  microblaze: pci-common cleanup
  microblaze: Support early console on uart16550
  microblaze: Do not compile early console support for uartlite if is disabled
  microblaze: Setup early console dynamically
  microblaze: Rename all uartlite early printk functions
  microblaze: remove early printk uarlite console dependency from header
  microblaze: Remove additional compatible properties
  microblaze: Remove hardcoded asm instraction for PVR loading
  microblaze: Use static const char * const where possible
  microblaze: Define VMALLOC_START/END
  ...

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
  hwmon: lis3: Release resources in case of failure
  hwmon: lis3: Short explanations of platform data fields
  hwmon: lis3: Enhance lis3 selftest with IRQ line test
  hwmon: lis3: use block read to access data registers
  hwmon: lis3: Adjust fuzziness for 8 bit device
  hwmon: lis3: New parameters to platform data
  hwmon: lis3: restore axis enabled bits
  hwmon: lis3: Power on corrections
  hwmon: lis3: Update coordinates at polled device open
  hwmon: lis3: Cleanup interrupt handling
  hwmon: lis3: regulator control
  hwmon: lis3: pm_runtime support
  Kirkwood: add fan support for Network Space Max v2
  hwmon: add generic GPIO fan driver
  hwmon: (coretemp) fix reading of microcode revision (v2)
  hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs
  hwmon: (pkgtemp) align driver initialization style with coretemp
  hwmon: LTC4261 Hardware monitoring driver
  hwmon: (lis3) add axes module parameter for custom axis-mapping
  hwmon: (hp_accel) Add HP Mini 510x family support
  ...

In the MN10300 arch, we occasionally see an assertion being tripped in
alloc_cwqs() at the following line:

        /* just in case, make sure it's actually aligned */
  --->  BUG_ON(!IS_ALIGNED(wq->cpu_wq.v, align));
        return wq->cpu_wq.v ? 0 : -ENOMEM;

The values are:

        wa->cpu_wq.v => 0x902776e0
        align => 0x100

and align is calculated by the following:

        const size_t align = max_t(size_t, 1 << WORK_STRUCT_FLAG_BITS,
                                   __alignof__(unsigned long long));

This is because the pointer in question (wq->cpu_wq.v) loses some of its
lower bits to control flags, and so the object it points to must be
sufficiently aligned to avoid the need to use those bits for pointing to
things.

Currently, 4 control bits and 4 colour bits are used in normal
circumstances, plus a debugging bit if debugging is set.  This requires
the cpu_workqueue_struct struct to be at least 256 bytes aligned (or 512
bytes aligned with debugging).

PERCPU() alignment on MN13000, however, is only 32 bytes as set in
vmlinux.lds.S.  So we set this to PAGE_SIZE (4096) to match most other
arches and stick a comment in alloc_cwqs() for anyone else who triggers
the assertion.
Reported-by: NAkira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NMark Salter <msalter@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If lis3lv02d_init_device fails, HW resources were not released
properly. In case of failure call release_resources if available.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

No one uses these MMRs so we didn't notice when the anomaly handling
logic was inverted.
Reported-by: NRobin Getz <robin.getz@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This code was useful during early port development when our icache code
wasn't solid, but that ship has sailed long ago, and no code calls this
function anymore (irq_panic).  So punt it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Short documentation at kernel doc format.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Configure chip to data ready mode in selftest and count received
interrupts to see that interrupt line(s) are working.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Add optional blockread function to interface driver. If available
the chip driver uses it for data register access. For 12 bit device
it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out
5 bytes since every second byte is dummy.
This optimizes bus usage and reduces number of operations and
interrupts needed for one data update.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Default fuziness is set smaller for 8 device.
In 12 bit device LSB is quite close to 1 mg
(mg = 1 / 1000 of earth gravity).
In 8bit device LSB is about 18 mg.
Set fuziness to 1 for 8 bit device.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Added default output data rate setting to platform data.
If default rate is 0, reset default value is used.
Added control for duration via platform data.
Added possibility to configure interrupts to trig on
both rising and falling edge. The lis3 WU unit can be
configured quite many ways and with some configurations it
is quite handy to get coordinate refresh when some
event trigs and when it reason goes away.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

All axis enable bits are set to 0 at module remove.
Restore reset default value at init.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Sometimes lis3 chip seems to fail to setup factory tuning at boot up.
This probably happens if there is some odd power ramp down ramp up sequence
for example in device restart. Set boot bit in control2 register to
trig boot sequence manually and wait until it is finished.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Call input device poll function at device open to refresh coordinates
immediately. This is needed for the case where poll interval is set to
zero and coordinate updates happens purely under interrupt control.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Irqcfg moved to chip data instead of platform data.
This simplifies access in interrupt handler little bit.

Input device open and close functions set status for
interrupt threaded handler once.

Unnecessary check for interrupt source removed since
it is enough that active interrupt line indicates that
there was an interrupt.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Based on pm_runtime control, turn lis3 regulators on and off.
Perform context save and restore on transitions.

Feature is optional and must be enabled in platform data.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Add pm_runtime support to lis3 core driver.
Add pm_runtime support to lis3 i2c driver.

spi and hp_accel drivers are not yet supported. Old always
on functionality remains for those.

For sysfs there is 5 second delay before turning off the
chip to avoid long ramp up delay.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Acked-by: NNicolas Pitre <nico@fluxnic.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

This patch adds hwmon support for fans connected to GPIO lines.

Platform specific information such as GPIO pinout and speed conversion array
(rpm from/to GPIO value) are passed to the driver via platform_data.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

According to the documentation, simply reading the respective MSR
isn't sufficient: It should be written with zeros, cpuid(1) be
executed, and then read (see arch/x86/kernel/cpu/intel.c for an
example).

v2: Fail probe when microcode revision cannot be determined, but is
needed to check for proper operation.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: NFenghua Yu <fenghua.yu@intel.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

CONFIG_HOTPLUG_CPU is used too much in some drivers.
This patch clean them up.
Signed-off-by: NChen Gong <gong.chen@linux.intel.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

pkgtemp is derived from coretemp, so some reasonable
logics should be applied onto pkgtemp, too. Such as
the init logic here.
Signed-off-by: NChen Gong <gong.chen@linux.intel.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

This driver adds support for Linear Technology LTC4261 I2C Negative
Voltage Hot Swap Controller.
Reviewed-by: NIra W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: NTom Grennan <tom.grennan@ericsson.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The axis-mapping of lis3dev device on many (rather most) HP machines
doesn't follow the standard.  When each new model appears, users need to
adjust again.  Testing this requires the rebuild of kernel, thus it's not
trivial for end-users.

This patch adds a module parameter "axes" to allow a custom axis-mapping
without patching and recompiling the kernel driver.  User can pass the
parameter such as axes=3,2,1.  Also it can be changed via sysfs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

This patch is an enhanced version of Takashi Iwai's
[PATCH] hp_accel: Add quirks for HP ProBook 532x and HP Mini 5102
My HP Mini 5101 works fine with this patch.
Confirmed with Tux Racer.

Signed-off by: Masanari Iida <standby24x7@gmail.com>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

A new version of LIS3 chip has slight incompatibilities from former
versions.  This patch adds the minimal support for it.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

These likely originate from these drivers being clones of one another
and/or other drivers which actually needed these includes.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

"break" after "return" is at best bogus (good compilers even warn about
the "break" being unreachable).
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

... as they're being called only from a __cpuinit function.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

* 'nfs-for-2.6.37' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (67 commits)
  SUNRPC: Cleanup duplicate assignment in rpcauth_refreshcred
  nfs: fix unchecked value
  Ask for time_delta during fsinfo probe
  Revalidate caches on lock
  SUNRPC: After calling xprt_release(), we must restart from call_reserve
  NFSv4: Fix up the 'dircount' hint in encode_readdir
  NFSv4: Clean up nfs4_decode_dirent
  NFSv4: nfs4_decode_dirent must clear entry->fattr->valid
  NFSv4: Fix a regression in decode_getfattr
  NFSv4: Fix up decode_attr_filehandle() to handle the case of empty fh pointer
  NFS: Ensure we check all allocation return values in new readdir code
  NFS: Readdir plus in v4
  NFS: introduce generic decode_getattr function
  NFS: check xdr_decode for errors
  NFS: nfs_readdir_filler catch all errors
  NFS: readdir with vmapped pages
  NFS: remove page size checking code
  NFS: decode_dirent should use an xdr_stream
  SUNRPC: Add a helper function xdr_inline_peek
  NFS: remove readdir plus limit
  ...

Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
  omap: complete removal of machine_desc.io_pg_offst and .phys_io
  omap: UART: fix wakeup registers for OMAP24xx UART2
  omap: Fix spotty MMC voltages
  ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
  serial: omap-serial: fix signess error
  OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
  omap: dma: Fix buffering disable bit setting for omap24xx
  omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
  OMAP3: PM: fix scratchpad memory accesses for off-mode
  omap4: pandaboard: enable the ehci port on pandaboard
  omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
  omap4: pandaboard: remove unused hsmmc definition
  OMAP: McBSP: Remove null omap44xx ops comment
  OMAP: McBSP: Swap CLKS source definition
  OMAP: McBSP: Fix CLKR and FSR signal muxing
  OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
  OMAP: control: move plat-omap/control.h to mach-omap2/control.h
  OMAP: split plat-omap/common.c
  OMAP: McBSP: implement functional clock switching via clock framework
  OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
  ...

Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony

Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci

* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
  davinci: fix remaining board support after io_pgoffst removal
  davinci: mityomapl138: make file local data static
  arm/davinci: remove duplicated include
  davinci: Initial support for Omapl138-Hawkboard
  davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
  davinci: add tnetv107x touchscreen platform device
  input: add driver for tnetv107x touchscreen controller
  davinci: add keypad config for tnetv107x evm board
  davinci: add tnetv107x keypad platform device
  input: add driver for tnetv107x on-chip keypad controller
  net: davinci_emac: cleanup unused cpdma code
  net: davinci_emac: switch to new cpdma layer
  net: davinci_emac: separate out cpdma code
  net: davinci_emac: cleanup unused mdio emac code
  omap: cleanup unused davinci mdio arch code
  davinci: cleanup mdio arch code and switch to phy_id
  net: davinci_emac: switch to new mdio
  omap: add mdio platform devices
  davinci: add mdio platform devices
  net: davinci_emac: separate out davinci mdio
  ...

Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)