Merge branch 'omap-for-linus' of...

Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
  omap: complete removal of machine_desc.io_pg_offst and .phys_io
  omap: UART: fix wakeup registers for OMAP24xx UART2
  omap: Fix spotty MMC voltages
  ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
  serial: omap-serial: fix signess error
  OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
  omap: dma: Fix buffering disable bit setting for omap24xx
  omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
  OMAP3: PM: fix scratchpad memory accesses for off-mode
  omap4: pandaboard: enable the ehci port on pandaboard
  omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
  omap4: pandaboard: remove unused hsmmc definition
  OMAP: McBSP: Remove null omap44xx ops comment
  OMAP: McBSP: Swap CLKS source definition
  OMAP: McBSP: Fix CLKR and FSR signal muxing
  OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
  OMAP: control: move plat-omap/control.h to mach-omap2/control.h
  OMAP: split plat-omap/common.c
  OMAP: McBSP: implement functional clock switching via clock framework
  OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
  ...

Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony

arch/arm/Kconfig

@@ -831,7 +831,7 @@ config ARCH_OMAP
 	select GENERIC_CLOCKEVENTS
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	help
-	  Support for TI's OMAP platform (OMAP1 and OMAP2).
+	  Support for TI's OMAP platform (OMAP1/2/3/4).
 
 config PLAT_SPEAR
 	bool "ST SPEAr"

arch/arm/configs/n8x0_defconfig

-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_LBDAF is not set
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-CONFIG_ARCH_OMAP=y
-CONFIG_ARCH_OMAP2=y
-CONFIG_OMAP_RESET_CLOCKS=y
-# CONFIG_OMAP_MUX is not set
-# CONFIG_OMAP_MCBSP is not set
-CONFIG_OMAP_MBOX_FWK=y
-CONFIG_OMAP_32K_TIMER=y
-CONFIG_ARCH_OMAP2420=y
-CONFIG_MACH_NOKIA_N8X0=y
-CONFIG_AEABI=y
-CONFIG_LEDS=y
-CONFIG_ZBOOT_ROM_TEXT=0x10C08000
-CONFIG_ZBOOT_ROM_BSS=0x10200000
-CONFIG_CMDLINE="root=/dev/mmcblk0p2 console=ttyS2,115200n8 debug earlyprintk rootwait"
-CONFIG_FPE_NWFPE=y
-CONFIG_VFP=y
-CONFIG_PM=y
-CONFIG_PM_RUNTIME=y
-CONFIG_NET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_ONENAND=y
-CONFIG_MTD_ONENAND_OMAP2=y
-CONFIG_MTD_ONENAND_OTP=y
-CONFIG_BLK_DEV_RAM=y
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-# CONFIG_I2C_COMPAT is not set
-# CONFIG_I2C_HELPER_AUTO is not set
-CONFIG_I2C_OMAP=y
-CONFIG_SPI=y
-CONFIG_SPI_OMAP24XX=y
-# CONFIG_HWMON is not set
-CONFIG_MENELAUS=y
-CONFIG_REGULATOR=y
-# CONFIG_VGA_CONSOLE is not set
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-CONFIG_USB_DEBUG=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_DEVICEFS=y
-CONFIG_USB_SUSPEND=y
-# CONFIG_USB_OTG_WHITELIST is not set
-CONFIG_USB_MUSB_HDRC=y
-CONFIG_USB_MUSB_OTG=y
-CONFIG_USB_GADGET_MUSB_HDRC=y
-# CONFIG_MUSB_PIO_ONLY is not set
-CONFIG_USB_MUSB_DEBUG=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_DEBUG=y
-CONFIG_USB_GADGET_DEBUG_FILES=y
-CONFIG_USB_ETH=m
-CONFIG_USB_ETH_EEM=y
-CONFIG_MMC=y
-CONFIG_MMC_OMAP=y
-CONFIG_EXT3_FS=y
-CONFIG_INOTIFY=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_SUMMARY=y
-CONFIG_JFFS2_COMPRESSION_OPTIONS=y
-CONFIG_JFFS2_LZO=y
-CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_CRC_CCITT=y

arch/arm/configs/omap3_defconfig → arch/arm/configs/omap2plus_defconfig

@@ -53,18 +53,18 @@ CONFIG_MACH_SBC3530=y
 CONFIG_MACH_OMAP_3630SDP=y
 CONFIG_MACH_OMAP_4430SDP=y
 CONFIG_ARM_THUMBEE=y
+CONFIG_ARM_L1_CACHE_SHIFT=5
+CONFIG_ARM_ERRATA_411920=y
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_SMP=y
+# CONFIG_LOCAL_TIMERS is not set
 CONFIG_AEABI=y
 CONFIG_LEDS=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/mmcblk0p2 rootwait console=ttyS2,115200"
+CONFIG_CMDLINE="root=/dev/mmcblk0p2 rootwait console=ttyO2,115200"
 CONFIG_KEXEC=y
-CONFIG_CPU_FREQ=y
-CONFIG_CPU_FREQ_STAT_DETAILS=y
-CONFIG_CPU_FREQ_GOV_USERSPACE=y
-CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_FPE_NWFPE=y
 CONFIG_VFP=y
 CONFIG_NEON=y
@@ -87,23 +87,23 @@ CONFIG_IP_PNP_RARP=y
 # CONFIG_INET_LRO is not set
 # CONFIG_IPV6 is not set
 CONFIG_NETFILTER=y
-CONFIG_BT=y
-CONFIG_BT_L2CAP=y
-CONFIG_BT_SCO=y
+CONFIG_BT=m
+CONFIG_BT_L2CAP=m
+CONFIG_BT_SCO=m
 CONFIG_BT_RFCOMM=y
 CONFIG_BT_RFCOMM_TTY=y
-CONFIG_BT_BNEP=y
+CONFIG_BT_BNEP=m
 CONFIG_BT_BNEP_MC_FILTER=y
 CONFIG_BT_BNEP_PROTO_FILTER=y
-CONFIG_BT_HIDP=y
-CONFIG_BT_HCIUART=y
+CONFIG_BT_HIDP=m
+CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_H4=y
 CONFIG_BT_HCIUART_BCSP=y
 CONFIG_BT_HCIUART_LL=y
-CONFIG_BT_HCIBCM203X=y
-CONFIG_BT_HCIBPA10X=y
-CONFIG_CFG80211=y
-CONFIG_MAC80211=y
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
 CONFIG_MAC80211_RC_PID=y
 CONFIG_MAC80211_RC_DEFAULT_PID=y
 CONFIG_MAC80211_LEDS=y
@@ -137,9 +137,11 @@ CONFIG_SMSC_PHY=y
 CONFIG_NET_ETHERNET=y
 CONFIG_SMC91X=y
 CONFIG_SMSC911X=y
-CONFIG_LIBERTAS=y
-CONFIG_LIBERTAS_USB=y
-CONFIG_LIBERTAS_SDIO=y
+CONFIG_KS8851=y
+CONFIG_KS8851_MLL=y
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+CONFIG_LIBERTAS_SDIO=m
 CONFIG_LIBERTAS_DEBUG=y
 CONFIG_USB_USBNET=y
 CONFIG_USB_ALI_M5632=y
@@ -201,8 +203,8 @@ CONFIG_FONTS=y
 CONFIG_FONT_8x8=y
 CONFIG_FONT_8x16=y
 CONFIG_LOGO=y
-CONFIG_SOUND=y
-CONFIG_SND=y
+CONFIG_SOUND=m
+CONFIG_SND=m
 CONFIG_SND_MIXER_OSS=y
 CONFIG_SND_PCM_OSS=y
 CONFIG_SND_VERBOSE_PRINTK=y
@@ -218,9 +220,9 @@ CONFIG_USB_DEVICEFS=y
 CONFIG_USB_SUSPEND=y
 # CONFIG_USB_OTG_WHITELIST is not set
 CONFIG_USB_MON=y
-CONFIG_USB_MUSB_HDRC=y
-CONFIG_USB_MUSB_OTG=y
-CONFIG_USB_GADGET_MUSB_HDRC=y
+# CONFIG_USB_MUSB_HDRC is not set
+# CONFIG_USB_MUSB_OTG is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
 CONFIG_USB_MUSB_DEBUG=y
 CONFIG_USB_WDM=y
 CONFIG_USB_STORAGE=y
@@ -276,12 +278,11 @@ CONFIG_DEBUG_KERNEL=y
 CONFIG_SCHEDSTATS=y
 CONFIG_TIMER_STATS=y
 CONFIG_PROVE_LOCKING=y
-CONFIG_LOCK_STAT=y
+# CONFIG_LOCK_STAT is not set
 CONFIG_DEBUG_SPINLOCK_SLEEP=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_DEBUG_INFO=y
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_DEBUG_LL=y
 CONFIG_SECURITY=y
 CONFIG_CRYPTO_MICHAEL_MIC=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set

arch/arm/configs/omap_4430sdp_defconfig

-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EMBEDDED=y
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_ELF_CORE is not set
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_MODULE_SRCVERSION_ALL=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_OMAP=y
-CONFIG_ARCH_OMAP4=y
-# CONFIG_ARCH_OMAP2PLUS_TYPICAL is not set
-# CONFIG_ARCH_OMAP2 is not set
-# CONFIG_ARCH_OMAP3 is not set
-# CONFIG_OMAP_MUX is not set
-CONFIG_OMAP_32K_TIMER=y
-CONFIG_OMAP_DM_TIMER=y
-CONFIG_MACH_OMAP_4430SDP=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_PL310_ERRATA_588369=y
-CONFIG_SMP=y
-CONFIG_NR_CPUS=2
-# CONFIG_LOCAL_TIMERS is not set
-CONFIG_PREEMPT=y
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/ram0 rw mem=128M console=ttyS2,115200n8 initrd=0x81600000,20M ramdisk_size=20480"
-CONFIG_VFP=y
-CONFIG_NEON=y
-CONFIG_BINFMT_MISC=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-# CONFIG_FW_LOADER is not set
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=16384
-# CONFIG_MISC_DEVICES is not set
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_KS8851=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=32
-CONFIG_SERIAL_8250_EXTENDED=y
-CONFIG_SERIAL_8250_MANY_PORTS=y
-CONFIG_SERIAL_8250_SHARE_IRQ=y
-CONFIG_SERIAL_8250_DETECT_IRQ=y
-CONFIG_SERIAL_8250_RSA=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_OMAP=y
-CONFIG_SPI=y
-CONFIG_SPI_OMAP24XX=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_OMAP_WATCHDOG=y
-CONFIG_TWL4030_CORE=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_TWL4030=y
-# CONFIG_VGA_CONSOLE is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-CONFIG_MMC=y
-CONFIG_MMC_OMAP_HS=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_TWL4030=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_FS_XATTR is not set
-CONFIG_INOTIFY=y
-CONFIG_QUOTA=y
-CONFIG_QFMT_V2=y
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DETECT_SOFTLOCKUP is not set
-CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-# CONFIG_FTRACE is not set
-# CONFIG_ARM_UNWIND is not set
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_PCBC=m
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRC_CCITT=y
-CONFIG_CRC_T10DIF=y
-CONFIG_LIBCRC32C=y

arch/arm/configs/omap_generic_2420_defconfig

-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_OMAP=y
-CONFIG_ARCH_OMAP2=y
-# CONFIG_OMAP_MUX is not set
-CONFIG_MACH_OMAP_GENERIC=y
-CONFIG_ARCH_OMAP2420=y
-CONFIG_LEDS=y
-CONFIG_ZBOOT_ROM_TEXT=0x10C08000
-CONFIG_ZBOOT_ROM_BSS=0x10200000
-CONFIG_FPE_NWFPE=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_WATCHDOG=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_VIDEO_OUTPUT_CONTROL=m
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_INOTIFY=y
-CONFIG_ROMFS_FS=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
-CONFIG_CRC_CCITT=y

arch/arm/mach-omap1/Makefile

@@ -12,7 +12,7 @@ obj-$(CONFIG_OMAP_MPU_TIMER)	+= time.o
 obj-$(CONFIG_OMAP_32K_TIMER)	+= timer32k.o
 
 # Power Management
-obj-$(CONFIG_PM) += pm.o sleep.o
+obj-$(CONFIG_PM) += pm.o sleep.o pm_bus.o
 
 # DSP
 obj-$(CONFIG_OMAP_MBOX_FWK)	+= mailbox_mach.o

arch/arm/mach-omap1/board-ams-delta.c

@@ -16,9 +16,12 @@
 #include <linux/init.h>
 #include <linux/input.h>
 #include <linux/interrupt.h>
+#include <linux/leds.h>
 #include <linux/platform_device.h>
 #include <linux/serial_8250.h>
 
+#include <media/soc_camera.h>
+
 #include <asm/serial.h>
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -32,6 +35,7 @@
 #include <plat/usb.h>
 #include <plat/board.h>
 #include <plat/common.h>
+#include <mach/camera.h>
 
 #include <mach/ams-delta-fiq.h>
 
@@ -213,10 +217,56 @@ static struct platform_device ams_delta_led_device = {
 	.id	= -1
 };
 
+static struct i2c_board_info ams_delta_camera_board_info[] = {
+	{
+		I2C_BOARD_INFO("ov6650", 0x60),
+	},
+};
+
+#ifdef CONFIG_LEDS_TRIGGERS
+DEFINE_LED_TRIGGER(ams_delta_camera_led_trigger);
+
+static int ams_delta_camera_power(struct device *dev, int power)
+{
+	/*
+	 * turn on camera LED
+	 */
+	if (power)
+		led_trigger_event(ams_delta_camera_led_trigger, LED_FULL);
+	else
+		led_trigger_event(ams_delta_camera_led_trigger, LED_OFF);
+	return 0;
+}
+#else
+#define ams_delta_camera_power	NULL
+#endif
+
+static struct soc_camera_link __initdata ams_delta_iclink = {
+	.bus_id         = 0,	/* OMAP1 SoC camera bus */
+	.i2c_adapter_id = 1,
+	.board_info     = &ams_delta_camera_board_info[0],
+	.module_name    = "ov6650",
+	.power		= ams_delta_camera_power,
+};
+
+static struct platform_device ams_delta_camera_device = {
+	.name   = "soc-camera-pdrv",
+	.id     = 0,
+	.dev    = {
+		.platform_data = &ams_delta_iclink,
+	},
+};
+
+static struct omap1_cam_platform_data ams_delta_camera_platform_data = {
+	.camexclk_khz	= 12000,	/* default 12MHz clock, no extra DPLL */
+	.lclk_khz_max	= 1334,		/* results in 5fps CIF, 10fps QCIF */
+};
+
 static struct platform_device *ams_delta_devices[] __initdata = {
 	&ams_delta_kp_device,
 	&ams_delta_lcd_device,
 	&ams_delta_led_device,
+	&ams_delta_camera_device,
 };
 
 static void __init ams_delta_init(void)
@@ -225,6 +275,20 @@ static void __init ams_delta_init(void)
 	omap_cfg_reg(UART1_TX);
 	omap_cfg_reg(UART1_RTS);
 
+	/* parallel camera interface */
+	omap_cfg_reg(H19_1610_CAM_EXCLK);
+	omap_cfg_reg(J15_1610_CAM_LCLK);
+	omap_cfg_reg(L18_1610_CAM_VS);
+	omap_cfg_reg(L15_1610_CAM_HS);
+	omap_cfg_reg(L19_1610_CAM_D0);
+	omap_cfg_reg(K14_1610_CAM_D1);
+	omap_cfg_reg(K15_1610_CAM_D2);
+	omap_cfg_reg(K19_1610_CAM_D3);
+	omap_cfg_reg(K18_1610_CAM_D4);
+	omap_cfg_reg(J14_1610_CAM_D5);
+	omap_cfg_reg(J19_1610_CAM_D6);
+	omap_cfg_reg(J18_1610_CAM_D7);
+
 	iotable_init(ams_delta_io_desc, ARRAY_SIZE(ams_delta_io_desc));
 
 	omap_board_config = ams_delta_config;
@@ -236,6 +300,11 @@ static void __init ams_delta_init(void)
 	ams_delta_latch2_write(~0, 0);
 
 	omap1_usb_init(&ams_delta_usb_config);
+	omap1_set_camera_info(&ams_delta_camera_platform_data);
+#ifdef CONFIG_LEDS_TRIGGERS
+	led_trigger_register_simple("ams_delta_camera",
+			&ams_delta_camera_led_trigger);
+#endif
 	platform_add_devices(ams_delta_devices, ARRAY_SIZE(ams_delta_devices));
 
 #ifdef CONFIG_AMS_DELTA_FIQ

arch/arm/mach-omap1/board-h2-mmc.c

@@ -58,8 +58,7 @@ static struct omap_mmc_platform_data mmc1_data = {
 	.dma_mask			= 0xffffffff,
 	.slots[0]       = {
 		.set_power              = mmc_set_power,
-		.ocr_mask               = MMC_VDD_28_29 | MMC_VDD_30_31 |
-					  MMC_VDD_32_33 | MMC_VDD_33_34,
+		.ocr_mask               = MMC_VDD_32_33 | MMC_VDD_33_34,
 		.name                   = "mmcblk",
 	},
 };

arch/arm/mach-omap1/board-h3-mmc.c

@@ -40,8 +40,7 @@ static struct omap_mmc_platform_data mmc1_data = {
 	.dma_mask			= 0xffffffff,
 	.slots[0]       = {
 		.set_power              = mmc_set_power,
-		.ocr_mask               = MMC_VDD_28_29 | MMC_VDD_30_31 |
-					  MMC_VDD_32_33 | MMC_VDD_33_34,
+		.ocr_mask               = MMC_VDD_32_33 | MMC_VDD_33_34,
 		.name                   = "mmcblk",
 	},
 };

arch/arm/mach-omap1/board-htcherald.c

@@ -30,6 +30,13 @@
 #include <linux/input.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+#include <linux/htcpld.h>
+#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -39,6 +46,7 @@
 #include <plat/board.h>
 #include <plat/keypad.h>
 #include <plat/usb.h>
+#include <plat/mmc.h>
 
 #include <mach/irqs.h>
 
@@ -52,13 +60,123 @@
 #define       OMAP_LCDC_CTRL_LCD_EN           (1 << 0)
 #define       OMAP_LCDC_STAT_DONE             (1 << 0)
 
-static struct omap_lcd_config htcherald_lcd_config __initdata = {
-	.ctrl_name	= "internal",
-};
+/* GPIO definitions for the power button and keyboard slide switch */
+#define HTCHERALD_GPIO_POWER 139
+#define HTCHERALD_GPIO_SLIDE 174
+#define HTCHERALD_GIRQ_BTNS 141
 
-static struct omap_board_config_kernel htcherald_config[] __initdata = {
-	{ OMAP_TAG_LCD, &htcherald_lcd_config },
-};
+/* GPIO definitions for the touchscreen */
+#define HTCHERALD_GPIO_TS 76
+
+/* HTCPLD definitions */
+
+/*
+ * CPLD Logic
+ *
+ * Chip 3 - 0x03
+ *
+ * Function            7 6 5 4  3 2 1 0
+ * ------------------------------------
+ * DPAD light          x x x x  x x x 1
+ * SoundDev            x x x x  1 x x x
+ * Screen white        1 x x x  x x x x
+ * MMC power on        x x x x  x 1 x x
+ * Happy times (n)     0 x x x  x 1 x x
+ *
+ * Chip 4 - 0x04
+ *
+ * Function            7 6 5 4  3 2 1 0
+ * ------------------------------------
+ * Keyboard light      x x x x  x x x 1
+ * LCD Bright (4)      x x x x  x 1 1 x
+ * LCD Bright (3)      x x x x  x 0 1 x
+ * LCD Bright (2)      x x x x  x 1 0 x
+ * LCD Bright (1)      x x x x  x 0 0 x
+ * LCD Off             x x x x  0 x x x
+ * LCD image (fb)      1 x x x  x x x x
+ * LCD image (white)   0 x x x  x x x x
+ * Caps lock LED       x x 1 x  x x x x
+ *
+ * Chip 5 - 0x05
+ *
+ * Function            7 6 5 4  3 2 1 0
+ * ------------------------------------
+ * Red (solid)         x x x x  x 1 x x
+ * Red (flash)         x x x x  x x 1 x
+ * Green (GSM flash)   x x x x  1 x x x
+ * Green (GSM solid)   x x x 1  x x x x
+ * Green (wifi flash)  x x 1 x  x x x x
+ * Blue (bt flash)     x 1 x x  x x x x
+ * DPAD Int Enable     1 x x x  x x x 0
+ *
+ * (Combinations of the above can be made for different colors.)
+ * The direction pad interrupt enable must be set each time the
+ * interrupt is handled.
+ *
+ * Chip 6 - 0x06
+ *
+ * Function            7 6 5 4  3 2 1 0
+ * ------------------------------------
+ * Vibrator            x x x x  1 x x x
+ * Alt LED             x x x 1  x x x x
+ * Screen white        1 x x x  x x x x
+ * Screen white        x x 1 x  x x x x
+ * Screen white        x 0 x x  x x x x
+ * Enable kbd dpad     x x x x  x x 0 x
+ * Happy Times         0 1 0 x  x x 0 x
+ */
+
+/*
+ * HTCPLD GPIO lines start 16 after OMAP_MAX_GPIO_LINES to account
+ * for the 16 MPUIO lines.
+ */
+#define HTCPLD_GPIO_START_OFFSET	(OMAP_MAX_GPIO_LINES + 16)
+#define HTCPLD_IRQ(chip, offset)	(OMAP_IRQ_END + 8 * (chip) + (offset))
+#define HTCPLD_BASE(chip, offset)	\
+	(HTCPLD_GPIO_START_OFFSET + 8 * (chip) + (offset))
+
+#define HTCPLD_GPIO_LED_DPAD		HTCPLD_BASE(0, 0)
+#define HTCPLD_GPIO_LED_KBD		HTCPLD_BASE(1, 0)
+#define HTCPLD_GPIO_LED_CAPS		HTCPLD_BASE(1, 5)
+#define HTCPLD_GPIO_LED_RED_FLASH	HTCPLD_BASE(2, 1)
+#define HTCPLD_GPIO_LED_RED_SOLID	HTCPLD_BASE(2, 2)
+#define HTCPLD_GPIO_LED_GREEN_FLASH	HTCPLD_BASE(2, 3)
+#define HTCPLD_GPIO_LED_GREEN_SOLID	HTCPLD_BASE(2, 4)
+#define HTCPLD_GPIO_LED_WIFI		HTCPLD_BASE(2, 5)
+#define HTCPLD_GPIO_LED_BT		HTCPLD_BASE(2, 6)
+#define HTCPLD_GPIO_LED_VIBRATE		HTCPLD_BASE(3, 3)
+#define HTCPLD_GPIO_LED_ALT		HTCPLD_BASE(3, 4)
+
+#define HTCPLD_GPIO_RIGHT_KBD		HTCPLD_BASE(6, 7)
+#define HTCPLD_GPIO_UP_KBD		HTCPLD_BASE(6, 6)
+#define HTCPLD_GPIO_LEFT_KBD		HTCPLD_BASE(6, 5)
+#define HTCPLD_GPIO_DOWN_KBD		HTCPLD_BASE(6, 4)
+
+#define HTCPLD_GPIO_RIGHT_DPAD		HTCPLD_BASE(7, 7)
+#define HTCPLD_GPIO_UP_DPAD		HTCPLD_BASE(7, 6)
+#define HTCPLD_GPIO_LEFT_DPAD		HTCPLD_BASE(7, 5)
+#define HTCPLD_GPIO_DOWN_DPAD		HTCPLD_BASE(7, 4)
+#define HTCPLD_GPIO_ENTER_DPAD		HTCPLD_BASE(7, 3)
+
+/*
+ * The htcpld chip requires a gpio write to a specific line
+ * to re-enable interrupts after one has occurred.
+ */
+#define HTCPLD_GPIO_INT_RESET_HI	HTCPLD_BASE(2, 7)
+#define HTCPLD_GPIO_INT_RESET_LO	HTCPLD_BASE(2, 0)
+
+/* Chip 5 */
+#define HTCPLD_IRQ_RIGHT_KBD		HTCPLD_IRQ(0, 7)
+#define HTCPLD_IRQ_UP_KBD		HTCPLD_IRQ(0, 6)
+#define HTCPLD_IRQ_LEFT_KBD		HTCPLD_IRQ(0, 5)
+#define HTCPLD_IRQ_DOWN_KBD		HTCPLD_IRQ(0, 4)
+
+/* Chip 6 */
+#define HTCPLD_IRQ_RIGHT_DPAD		HTCPLD_IRQ(1, 7)
+#define HTCPLD_IRQ_UP_DPAD		HTCPLD_IRQ(1, 6)
+#define HTCPLD_IRQ_LEFT_DPAD		HTCPLD_IRQ(1, 5)
+#define HTCPLD_IRQ_DOWN_DPAD		HTCPLD_IRQ(1, 4)
+#define HTCPLD_IRQ_ENTER_DPAD		HTCPLD_IRQ(1, 3)
 
 /* Keyboard definition */
 
@@ -140,6 +258,129 @@ static struct platform_device kp_device = {
 	.resource	= kp_resources,
 };
 
+/* GPIO buttons for keyboard slide and power button */
+static struct gpio_keys_button herald_gpio_keys_table[] = {
+	{BTN_0,  HTCHERALD_GPIO_POWER, 1, "POWER", EV_KEY, 1, 20},
+	{SW_LID, HTCHERALD_GPIO_SLIDE, 0, "SLIDE", EV_SW,  1, 20},
+
+	{KEY_LEFT,  HTCPLD_GPIO_LEFT_KBD,  1, "LEFT",  EV_KEY, 1, 20},
+	{KEY_RIGHT, HTCPLD_GPIO_RIGHT_KBD, 1, "RIGHT", EV_KEY, 1, 20},
+	{KEY_UP,    HTCPLD_GPIO_UP_KBD,    1, "UP",    EV_KEY, 1, 20},
+	{KEY_DOWN,  HTCPLD_GPIO_DOWN_KBD,  1, "DOWN",  EV_KEY, 1, 20},
+
+	{KEY_LEFT,  HTCPLD_GPIO_LEFT_DPAD,   1, "DLEFT",  EV_KEY, 1, 20},
+	{KEY_RIGHT, HTCPLD_GPIO_RIGHT_DPAD,  1, "DRIGHT", EV_KEY, 1, 20},
+	{KEY_UP,    HTCPLD_GPIO_UP_DPAD,     1, "DUP",    EV_KEY, 1, 20},
+	{KEY_DOWN,  HTCPLD_GPIO_DOWN_DPAD,   1, "DDOWN",  EV_KEY, 1, 20},
+	{KEY_ENTER, HTCPLD_GPIO_ENTER_DPAD,  1, "DENTER", EV_KEY, 1, 20},
+};
+
+static struct gpio_keys_platform_data herald_gpio_keys_data = {
+	.buttons	= herald_gpio_keys_table,
+	.nbuttons	= ARRAY_SIZE(herald_gpio_keys_table),
+	.rep		= 1,
+};
+
+static struct platform_device herald_gpiokeys_device = {
+	.name      = "gpio-keys",
+	.id		= -1,
+	.dev = {
+		.platform_data = &herald_gpio_keys_data,
+	},
+};
+
+/* LEDs for the Herald.  These connect to the HTCPLD GPIO device. */
+static struct gpio_led gpio_leds[] = {
+	{"dpad",        NULL, HTCPLD_GPIO_LED_DPAD,        0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"kbd",         NULL, HTCPLD_GPIO_LED_KBD,         0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"vibrate",     NULL, HTCPLD_GPIO_LED_VIBRATE,     0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"green_solid", NULL, HTCPLD_GPIO_LED_GREEN_SOLID, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"green_flash", NULL, HTCPLD_GPIO_LED_GREEN_FLASH, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"red_solid",   "mmc0", HTCPLD_GPIO_LED_RED_SOLID, 0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"red_flash",   NULL, HTCPLD_GPIO_LED_RED_FLASH,   0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"wifi",        NULL, HTCPLD_GPIO_LED_WIFI,        0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"bt",          NULL, HTCPLD_GPIO_LED_BT,          0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"caps",        NULL, HTCPLD_GPIO_LED_CAPS,        0, 0, LEDS_GPIO_DEFSTATE_OFF},
+	{"alt",         NULL, HTCPLD_GPIO_LED_ALT,         0, 0, LEDS_GPIO_DEFSTATE_OFF},
+};
+
+static struct gpio_led_platform_data gpio_leds_data = {
+	.leds		= gpio_leds,
+	.num_leds	= ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device gpio_leds_device = {
+	.name		= "leds-gpio",
+	.id		= 0,
+	.dev	= {
+		.platform_data	= &gpio_leds_data,
+	},
+};
+
+/* HTC PLD chips */
+
+static struct resource htcpld_resources[] = {
+	[0] = {
+		.start  = OMAP_GPIO_IRQ(HTCHERALD_GIRQ_BTNS),
+		.end    = OMAP_GPIO_IRQ(HTCHERALD_GIRQ_BTNS),
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+struct htcpld_chip_platform_data htcpld_chips[] = {
+	[0] = {
+		.addr		= 0x03,
+		.reset		= 0x04,
+		.num_gpios	= 8,
+		.gpio_out_base	= HTCPLD_BASE(0, 0),
+		.gpio_in_base	= HTCPLD_BASE(4, 0),
+	},
+	[1] = {
+		.addr		= 0x04,
+		.reset		= 0x8e,
+		.num_gpios	= 8,
+		.gpio_out_base	= HTCPLD_BASE(1, 0),
+		.gpio_in_base	= HTCPLD_BASE(5, 0),
+	},
+	[2] = {
+		.addr		= 0x05,
+		.reset		= 0x80,
+		.num_gpios	= 8,
+		.gpio_out_base	= HTCPLD_BASE(2, 0),
+		.gpio_in_base	= HTCPLD_BASE(6, 0),
+		.irq_base	= HTCPLD_IRQ(0, 0),
+		.num_irqs	= 8,
+	},
+	[3] = {
+		.addr		= 0x06,
+		.reset		= 0x40,
+		.num_gpios	= 8,
+		.gpio_out_base	= HTCPLD_BASE(3, 0),
+		.gpio_in_base	= HTCPLD_BASE(7, 0),
+		.irq_base	= HTCPLD_IRQ(1, 0),
+		.num_irqs	= 8,
+	},
+};
+
+struct htcpld_core_platform_data htcpld_pfdata = {
+	.int_reset_gpio_hi = HTCPLD_GPIO_INT_RESET_HI,
+	.int_reset_gpio_lo = HTCPLD_GPIO_INT_RESET_LO,
+	.i2c_adapter_id	   = 1,
+
+	.chip		   = htcpld_chips,
+	.num_chip	   = ARRAY_SIZE(htcpld_chips),
+};
+
+static struct platform_device htcpld_device = {
+	.name		= "i2c-htcpld",
+	.id		= -1,
+	.resource	= htcpld_resources,
+	.num_resources	= ARRAY_SIZE(htcpld_resources),
+	.dev	= {
+		.platform_data	= &htcpld_pfdata,
+	},
+};
+
 /* USB Device */
 static struct omap_usb_config htcherald_usb_config __initdata = {
 	.otg = 0,
@@ -150,14 +391,71 @@ static struct omap_usb_config htcherald_usb_config __initdata = {
 };
 
 /* LCD Device resources */
+static struct omap_lcd_config htcherald_lcd_config __initdata = {
+	.ctrl_name	= "internal",
+};
+
+static struct omap_board_config_kernel htcherald_config[] __initdata = {
+	{ OMAP_TAG_LCD, &htcherald_lcd_config },
+};
+
 static struct platform_device lcd_device = {
 	.name           = "lcd_htcherald",
 	.id             = -1,
 };
 
+/* MMC Card */
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+static struct omap_mmc_platform_data htc_mmc1_data = {
+	.nr_slots                       = 1,
+	.switch_slot                    = NULL,
+	.slots[0]       = {
+		.ocr_mask               = MMC_VDD_32_33 | MMC_VDD_33_34,
+		.name                   = "mmcblk",
+		.nomux                  = 1,
+		.wires                  = 4,
+		.switch_pin             = -1,
+	},
+};
+
+static struct omap_mmc_platform_data *htc_mmc_data[1];
+#endif
+
+
+/* Platform devices for the Herald */
 static struct platform_device *devices[] __initdata = {
 	&kp_device,
 	&lcd_device,
+	&htcpld_device,
+	&gpio_leds_device,
+	&herald_gpiokeys_device,
+};
+
+/*
+ * Touchscreen
+ */
+static const struct ads7846_platform_data htcherald_ts_platform_data = {
+	.model			= 7846,
+	.keep_vref_on		= 1,
+	.x_plate_ohms		= 496,
+	.gpio_pendown		= HTCHERALD_GPIO_TS,
+	.pressure_max		= 100000,
+	.pressure_min		= 5000,
+	.x_min			= 528,
+	.x_max			= 3760,
+	.y_min			= 624,
+	.y_max			= 3760,
+};
+
+static struct spi_board_info __initdata htcherald_spi_board_info[] = {
+	{
+		.modalias		= "ads7846",
+		.platform_data		= &htcherald_ts_platform_data,
+		.irq			= OMAP_GPIO_IRQ(HTCHERALD_GPIO_TS),
+		.max_speed_hz		= 2500000,
+		.bus_num		= 2,
+		.chip_select		= 1,
+	}
 };
 
 /*
@@ -278,6 +576,7 @@ static void __init htcherald_init(void)
 {
 	printk(KERN_INFO "HTC Herald init.\n");
 
+	/* Do board initialization before we register all the devices */
 	omap_gpio_init();
 
 	omap_board_config = htcherald_config;
@@ -288,6 +587,16 @@ static void __init htcherald_init(void)
 
 	htcherald_usb_enable();
 	omap1_usb_init(&htcherald_usb_config);
+
+	spi_register_board_info(htcherald_spi_board_info,
+		ARRAY_SIZE(htcherald_spi_board_info));
+
+	omap_register_i2c_bus(1, 100, NULL, 0);
+
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+	htc_mmc_data[0] = &htc_mmc1_data;
+	omap1_init_mmc(htc_mmc_data, 1);
+#endif
 }
 
 static void __init htcherald_init_irq(void)

arch/arm/mach-omap1/board-sx1-mmc.c

@@ -44,8 +44,7 @@ static struct omap_mmc_platform_data mmc1_data = {
 	.nr_slots                       = 1,
 	.slots[0]       = {
 		.set_power              = mmc_set_power,
-		.ocr_mask               = MMC_VDD_28_29 | MMC_VDD_30_31 |
-					  MMC_VDD_32_33 | MMC_VDD_33_34,
+		.ocr_mask               = MMC_VDD_32_33 | MMC_VDD_33_34,
 		.name                   = "mmcblk",
 	},
 };

arch/arm/mach-omap1/devices.c

@@ -9,6 +9,7 @@
  * (at your option) any later version.
  */
 
+#include <linux/dma-mapping.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -192,6 +193,48 @@ static inline void omap_init_spi100k(void)
 }
 #endif
 
+
+#define OMAP1_CAMERA_BASE	0xfffb6800
+#define OMAP1_CAMERA_IOSIZE	0x1c
+
+static struct resource omap1_camera_resources[] = {
+	[0] = {
+		.start	= OMAP1_CAMERA_BASE,
+		.end	= OMAP1_CAMERA_BASE + OMAP1_CAMERA_IOSIZE - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= INT_CAMERA,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static u64 omap1_camera_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device omap1_camera_device = {
+	.name		= "omap1-camera",
+	.id		= 0, /* This is used to put cameras on this interface */
+	.dev		= {
+		.dma_mask		= &omap1_camera_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.num_resources	= ARRAY_SIZE(omap1_camera_resources),
+	.resource	= omap1_camera_resources,
+};
+
+void __init omap1_camera_init(void *info)
+{
+	struct platform_device *dev = &omap1_camera_device;
+	int ret;
+
+	dev->dev.platform_data = info;
+
+	ret = platform_device_register(dev);
+	if (ret)
+		dev_err(&dev->dev, "unable to register device: %d\n", ret);
+}
+
+
 /*-------------------------------------------------------------------------*/
 
 static inline void omap_init_sti(void) {}
@@ -258,3 +301,30 @@ static int __init omap1_init_devices(void)
 }
 arch_initcall(omap1_init_devices);
 
+#if defined(CONFIG_OMAP_WATCHDOG) || defined(CONFIG_OMAP_WATCHDOG_MODULE)
+
+static struct resource wdt_resources[] = {
+	{
+		.start		= 0xfffeb000,
+		.end		= 0xfffeb07F,
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device omap_wdt_device = {
+	.name	   = "omap_wdt",
+	.id	     = -1,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
+	.resource	= wdt_resources,
+};
+
+static int __init omap_init_wdt(void)
+{
+	if (!cpu_is_omap16xx())
+		return;
+
+	platform_device_register(&omap_wdt_device);
+	return 0;
+}
+subsys_initcall(omap_init_wdt);
+#endif

arch/arm/mach-omap1/include/mach/camera.h

+#ifndef __ASM_ARCH_CAMERA_H_
+#define __ASM_ARCH_CAMERA_H_
+
+void omap1_camera_init(void *);
+
+static inline void omap1_set_camera_info(struct omap1_cam_platform_data *info)
+{
+	omap1_camera_init(info);
+}
+
+#endif /* __ASM_ARCH_CAMERA_H_ */

arch/arm/mach-omap1/pm_bus.c

+/*
+ * Runtime PM support code for OMAP1
+ *
+ * Author: Kevin Hilman, Deep Root Systems, LLC
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/pm_runtime.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+
+#include <plat/omap_device.h>
+#include <plat/omap-pm.h>
+
+#ifdef CONFIG_PM_RUNTIME
+static int omap1_pm_runtime_suspend(struct device *dev)
+{
+	struct clk *iclk, *fclk;
+	int ret = 0;
+
+	dev_dbg(dev, "%s\n", __func__);
+
+	ret = pm_generic_runtime_suspend(dev);
+
+	fclk = clk_get(dev, "fck");
+	if (!IS_ERR(fclk)) {
+		clk_disable(fclk);
+		clk_put(fclk);
+	}
+
+	iclk = clk_get(dev, "ick");
+	if (!IS_ERR(iclk)) {
+		clk_disable(iclk);
+		clk_put(iclk);
+	}
+
+	return 0;
+};
+
+static int omap1_pm_runtime_resume(struct device *dev)
+{
+	int ret = 0;
+	struct clk *iclk, *fclk;
+
+	dev_dbg(dev, "%s\n", __func__);
+
+	iclk = clk_get(dev, "ick");
+	if (!IS_ERR(iclk)) {
+		clk_enable(iclk);
+		clk_put(iclk);
+	}
+
+	fclk = clk_get(dev, "fck");
+	if (!IS_ERR(fclk)) {
+		clk_enable(fclk);
+		clk_put(fclk);
+	}
+
+	return pm_generic_runtime_resume(dev);
+};
+
+static int __init omap1_pm_runtime_init(void)
+{
+	const struct dev_pm_ops *pm;
+	struct dev_pm_ops *omap_pm;
+
+	pm = platform_bus_get_pm_ops();
+	if (!pm) {
+		pr_err("%s: unable to get dev_pm_ops from platform_bus\n",
+			__func__);
+		return -ENODEV;
+	}
+
+	omap_pm = kmemdup(pm, sizeof(struct dev_pm_ops), GFP_KERNEL);
+	if (!omap_pm) {
+		pr_err("%s: unable to alloc memory for new dev_pm_ops\n",
+			__func__);
+		return -ENOMEM;
+	}
+
+	omap_pm->runtime_suspend = omap1_pm_runtime_suspend;
+	omap_pm->runtime_resume = omap1_pm_runtime_resume;
+
+	platform_bus_set_pm_ops(omap_pm);
+
+	return 0;
+}
+core_initcall(omap1_pm_runtime_init);
+#endif /* CONFIG_PM_RUNTIME */

arch/arm/mach-omap2/Kconfig

@@ -11,9 +11,8 @@ config ARCH_OMAP2PLUS_TYPICAL
 	select PM_RUNTIME
 	select VFP
 	select NEON if ARCH_OMAP3 || ARCH_OMAP4
-	select SERIAL_8250
-	select SERIAL_CORE_CONSOLE
-	select SERIAL_8250_CONSOLE
+	select SERIAL_OMAP
+	select SERIAL_OMAP_CONSOLE
 	select I2C
 	select I2C_OMAP
 	select MFD
@@ -35,7 +34,7 @@ config ARCH_OMAP3
 	default y
 	select CPU_V7
 	select USB_ARCH_HAS_EHCI
-	select ARM_L1_CACHE_SHIFT_6
+	select ARM_L1_CACHE_SHIFT_6 if !ARCH_OMAP4
 
 config ARCH_OMAP4
 	bool "TI OMAP4"
@@ -43,6 +42,8 @@ config ARCH_OMAP4
 	depends on ARCH_OMAP2PLUS
 	select CPU_V7
 	select ARM_GIC
+	select PL310_ERRATA_588369
+	select ARM_ERRATA_720789
 
 comment "OMAP Core Type"
 	depends on ARCH_OMAP2
@@ -99,20 +100,20 @@ config MACH_OMAP2_TUSB6010
 
 config MACH_OMAP_H4
 	bool "OMAP 2420 H4 board"
-	depends on ARCH_OMAP2
+	depends on ARCH_OMAP2420
 	default y
 	select OMAP_PACKAGE_ZAF
 	select OMAP_DEBUG_DEVICES
 
 config MACH_OMAP_APOLLON
 	bool "OMAP 2420 Apollon board"
-	depends on ARCH_OMAP2
+	depends on ARCH_OMAP2420
 	default y
 	select OMAP_PACKAGE_ZAC
 
 config MACH_OMAP_2430SDP
 	bool "OMAP 2430 SDP board"
-	depends on ARCH_OMAP2
+	depends on ARCH_OMAP2430
 	default y
 	select OMAP_PACKAGE_ZAC
 
@@ -135,6 +136,26 @@ config MACH_OMAP_LDP
 	default y
 	select OMAP_PACKAGE_CBB
 
+config MACH_OMAP3530_LV_SOM
+	bool "OMAP3 Logic 3530 LV SOM board"
+	depends on ARCH_OMAP3
+	select OMAP_PACKAGE_CBB
+	default y
+	help
+	 Support for the LogicPD OMAP3530 SOM Development kit
+	 for full description please see the products webpage at
+	 http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap35x-development-kit
+
+config MACH_OMAP3_TORPEDO
+	bool "OMAP3 Logic 35x Torpedo board"
+	depends on ARCH_OMAP3
+	select OMAP_PACKAGE_CBB
+	default y
+	help
+	 Support for the LogicPD OMAP35x Torpedo Development kit
+	 for full description please see the products webpage at
+	 http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit
+
 config MACH_OVERO
 	bool "Gumstix Overo board"
 	depends on ARCH_OMAP3
@@ -200,12 +221,18 @@ config MACH_OMAP_ZOOM2
 	depends on ARCH_OMAP3
 	default y
 	select OMAP_PACKAGE_CBB
+	select SERIAL_8250
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_8250_CONSOLE
 
 config MACH_OMAP_ZOOM3
 	bool "OMAP3630 Zoom3 board"
 	depends on ARCH_OMAP3
 	default y
 	select OMAP_PACKAGE_CBP
+	select SERIAL_8250
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_8250_CONSOLE
 
 config MACH_CM_T35
 	bool "CompuLab CM-T35 module"
@@ -214,12 +241,25 @@ config MACH_CM_T35
 	select OMAP_PACKAGE_CUS
 	select OMAP_MUX
 
+config MACH_CM_T3517
+	bool "CompuLab CM-T3517 module"
+	depends on ARCH_OMAP3
+	default y
+	select OMAP_PACKAGE_CBB
+	select OMAP_MUX
+
 config MACH_IGEP0020
 	bool "IGEP v2 board"
 	depends on ARCH_OMAP3
 	default y
 	select OMAP_PACKAGE_CBB
 
+config MACH_IGEP0030
+	bool "IGEP OMAP3 module"
+	depends on ARCH_OMAP3
+	default y
+	select OMAP_PACKAGE_CBB
+
 config MACH_SBC3530
 	bool "OMAP3 SBC STALKER board"
 	depends on ARCH_OMAP3

arch/arm/mach-omap2/Makefile

@@ -3,9 +3,10 @@
 #
 
 # Common support
-obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer-gp.o pm.o
+obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer-gp.o pm.o \
+	 common.o
 
-omap-2-3-common				= irq.o sdrc.o
+omap-2-3-common				= irq.o sdrc.o prm2xxx_3xxx.o
 hwmod-common				= omap_hwmod.o \
 					  omap_hwmod_common_data.o
 prcm-common				= prcm.o powerdomain.o
@@ -15,7 +16,7 @@ clock-common				= clock.o clock_common_data.o \
 
 obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(prcm-common) $(hwmod-common)
 obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(prcm-common) $(hwmod-common)
-obj-$(CONFIG_ARCH_OMAP4) += $(prcm-common) $(hwmod-common)
+obj-$(CONFIG_ARCH_OMAP4) += $(prcm-common) prm44xx.o $(hwmod-common)
 
 obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 
@@ -49,14 +50,18 @@ obj-$(CONFIG_ARCH_OMAP2)		+= sdrc2xxx.o
 # Power Management
 ifeq ($(CONFIG_PM),y)
 obj-$(CONFIG_ARCH_OMAP2)		+= pm24xx.o
-obj-$(CONFIG_ARCH_OMAP2)		+= sleep24xx.o
-obj-$(CONFIG_ARCH_OMAP3)		+= pm34xx.o sleep34xx.o cpuidle34xx.o
-obj-$(CONFIG_ARCH_OMAP4)		+= pm44xx.o
+obj-$(CONFIG_ARCH_OMAP2)		+= sleep24xx.o pm_bus.o
+obj-$(CONFIG_ARCH_OMAP3)		+= pm34xx.o sleep34xx.o cpuidle34xx.o pm_bus.o
+obj-$(CONFIG_ARCH_OMAP4)		+= pm44xx.o pm_bus.o
 obj-$(CONFIG_PM_DEBUG)			+= pm-debug.o
 
 AFLAGS_sleep24xx.o			:=-Wa,-march=armv6
 AFLAGS_sleep34xx.o			:=-Wa,-march=armv7-a
 
+ifeq ($(CONFIG_PM_VERBOSE),y)
+CFLAGS_pm_bus.o				+= -DDEBUG
+endif
+
 endif
 
 # PRCM
@@ -87,6 +92,7 @@ obj-$(CONFIG_ARCH_OMAP2430)		+= opp2430_data.o
 obj-$(CONFIG_ARCH_OMAP2420)		+= omap_hwmod_2420_data.o
 obj-$(CONFIG_ARCH_OMAP2430)		+= omap_hwmod_2430_data.o
 obj-$(CONFIG_ARCH_OMAP3)		+= omap_hwmod_3xxx_data.o
+obj-$(CONFIG_ARCH_OMAP4)		+= omap_hwmod_44xx_data.o
 
 # EMU peripherals
 obj-$(CONFIG_OMAP3_EMU)			+= emu.o
@@ -115,6 +121,10 @@ obj-$(CONFIG_MACH_DEVKIT8000)     	+= board-devkit8000.o \
 obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o \
 					   board-flash.o \
 					   hsmmc.o
+obj-$(CONFIG_MACH_OMAP3530_LV_SOM)      += board-omap3logic.o \
+					   hsmmc.o
+obj-$(CONFIG_MACH_OMAP3_TORPEDO)        += board-omap3logic.o \
+					   hsmmc.o
 obj-$(CONFIG_MACH_OVERO)		+= board-overo.o \
 					   hsmmc.o
 obj-$(CONFIG_MACH_OMAP3EVM)		+= board-omap3evm.o \
@@ -146,8 +156,11 @@ obj-$(CONFIG_MACH_OMAP_3630SDP)		+= board-3630sdp.o \
 					   hsmmc.o
 obj-$(CONFIG_MACH_CM_T35)		+= board-cm-t35.o \
 					   hsmmc.o
+obj-$(CONFIG_MACH_CM_T3517)		+= board-cm-t3517.o
 obj-$(CONFIG_MACH_IGEP0020)		+= board-igep0020.o \
 					   hsmmc.o
+obj-$(CONFIG_MACH_IGEP0030)		+= board-igep0030.o \
+					   hsmmc.o
 obj-$(CONFIG_MACH_OMAP3_TOUCHBOOK)	+= board-omap3touchbook.o \
 					   hsmmc.o
 obj-$(CONFIG_MACH_OMAP_4430SDP)		+= board-4430sdp.o \
@@ -174,3 +187,6 @@ obj-y					+= $(nand-m) $(nand-y)
 
 smc91x-$(CONFIG_SMC91X)			:= gpmc-smc91x.o
 obj-y					+= $(smc91x-m) $(smc91x-y)
+
+smsc911x-$(CONFIG_SMSC911X)		:= gpmc-smsc911x.o
+obj-y					+= $(smsc911x-m) $(smsc911x-y)

arch/arm/mach-omap2/board-2430sdp.c

@@ -19,6 +19,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
+#include <linux/mmc/host.h>
 #include <linux/delay.h>
 #include <linux/i2c/twl.h>
 #include <linux/err.h>
@@ -190,7 +191,7 @@ static int __init omap2430_i2c_init(void)
 static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.ext_clock	= 1,

arch/arm/mach-omap2/board-3430sdp.c

@@ -24,6 +24,7 @@
 #include <linux/regulator/machine.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
+#include <linux/mmc/host.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -38,15 +39,14 @@
 #include <plat/gpmc.h>
 #include <plat/display.h>
 
-#include <plat/control.h>
 #include <plat/gpmc-smc91x.h>
 
-#include <mach/board-flash.h>
-
+#include "board-flash.h"
 #include "mux.h"
 #include "sdram-qimonda-hyb18m512160af-6.h"
 #include "hsmmc.h"
 #include "pm.h"
+#include "control.h"
 
 #define CONFIG_DISABLE_HFCLK 1
 
@@ -76,7 +76,7 @@ static struct cpuidle_params omap3_cpuidle_params_table[] = {
 	{1, 10000, 30000, 300000},
 };
 
-static int board_keymap[] = {
+static uint32_t board_keymap[] = {
 	KEY(0, 0, KEY_LEFT),
 	KEY(0, 1, KEY_RIGHT),
 	KEY(0, 2, KEY_A),
@@ -353,12 +353,12 @@ static struct omap2_hsmmc_info mmc[] = {
 		/* 8 bits (default) requires S6.3 == ON,
 		 * so the SIM card isn't used; else 4 bits.
 		 */
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 4,
 	},
 	{
 		.mmc		= 2,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 7,
 	},
 	{}	/* Terminator */

arch/arm/mach-omap2/board-3630sdp.c

@@ -21,8 +21,8 @@
 #include <plat/usb.h>
 
 #include <mach/board-zoom.h>
-#include <mach/board-flash.h>
 
+#include "board-flash.h"
 #include "mux.h"
 #include "sdram-hynix-h8mbx00u0mer-0em.h"
 
@@ -208,7 +208,6 @@ static struct flash_partitions sdp_flash_partitions[] = {
 static void __init omap_sdp_init(void)
 {
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
-	omap_serial_init();
 	zoom_peripherals_init();
 	board_smc91x_init();
 	board_flash_init(sdp_flash_partitions, chip_sel_sdp);

arch/arm/mach-omap2/board-4430sdp.c

@@ -20,6 +20,7 @@
 #include <linux/usb/otg.h>
 #include <linux/spi/spi.h>
 #include <linux/i2c/twl.h>
+#include <linux/gpio_keys.h>
 #include <linux/regulator/machine.h>
 #include <linux/leds.h>
 
@@ -31,15 +32,18 @@
 
 #include <plat/board.h>
 #include <plat/common.h>
-#include <plat/control.h>
-#include <plat/timer-gp.h>
 #include <plat/usb.h>
 #include <plat/mmc.h>
+
 #include "hsmmc.h"
+#include "timer-gp.h"
+#include "control.h"
 
 #define ETH_KS8851_IRQ			34
 #define ETH_KS8851_POWER_ON		48
 #define ETH_KS8851_QUART		138
+#define OMAP4_SFH7741_SENSOR_OUTPUT_GPIO	184
+#define OMAP4_SFH7741_ENABLE_GPIO		188
 
 static struct gpio_led sdp4430_gpio_leds[] = {
 	{
@@ -77,11 +81,47 @@ static struct gpio_led sdp4430_gpio_leds[] = {
 
 };
 
+static struct gpio_keys_button sdp4430_gpio_keys[] = {
+	{
+		.desc			= "Proximity Sensor",
+		.type			= EV_SW,
+		.code			= SW_FRONT_PROXIMITY,
+		.gpio			= OMAP4_SFH7741_SENSOR_OUTPUT_GPIO,
+		.active_low		= 0,
+	}
+};
+
 static struct gpio_led_platform_data sdp4430_led_data = {
 	.leds	= sdp4430_gpio_leds,
 	.num_leds	= ARRAY_SIZE(sdp4430_gpio_leds),
 };
 
+static int omap_prox_activate(struct device *dev)
+{
+	gpio_set_value(OMAP4_SFH7741_ENABLE_GPIO , 1);
+	return 0;
+}
+
+static void omap_prox_deactivate(struct device *dev)
+{
+	gpio_set_value(OMAP4_SFH7741_ENABLE_GPIO , 0);
+}
+
+static struct gpio_keys_platform_data sdp4430_gpio_keys_data = {
+	.buttons	= sdp4430_gpio_keys,
+	.nbuttons	= ARRAY_SIZE(sdp4430_gpio_keys),
+	.enable		= omap_prox_activate,
+	.disable	= omap_prox_deactivate,
+};
+
+static struct platform_device sdp4430_gpio_keys_device = {
+	.name	= "gpio-keys",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &sdp4430_gpio_keys_data,
+	},
+};
+
 static struct platform_device sdp4430_leds_gpio = {
 	.name	= "leds-gpio",
 	.id	= -1,
@@ -161,6 +201,7 @@ static struct platform_device sdp4430_lcd_device = {
 
 static struct platform_device *sdp4430_devices[] __initdata = {
 	&sdp4430_lcd_device,
+	&sdp4430_gpio_keys_device,
 	&sdp4430_leds_gpio,
 };
 
@@ -193,15 +234,16 @@ static struct omap_musb_board_data musb_board_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= -EINVAL,
 	},
 	{
 		.mmc		= 2,
-		.wires		= 8,
+		.caps		=  MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.nonremovable   = true,
+		.ocr_mask	= MMC_VDD_29_30,
 	},
 	{}	/* Terminator */
 };
@@ -235,8 +277,14 @@ static int omap4_twl6030_hsmmc_late_init(struct device *dev)
 
 static __init void omap4_twl6030_hsmmc_set_late_init(struct device *dev)
 {
-	struct omap_mmc_platform_data *pdata = dev->platform_data;
+	struct omap_mmc_platform_data *pdata;
 
+	/* dev can be null if CONFIG_MMC_OMAP_HS is not set */
+	if (!dev) {
+		pr_err("Failed %s\n", __func__);
+		return;
+	}
+	pdata = dev->platform_data;
 	pdata->init =	omap4_twl6030_hsmmc_late_init;
 }
 
@@ -412,6 +460,11 @@ static struct i2c_board_info __initdata sdp4430_i2c_3_boardinfo[] = {
 		I2C_BOARD_INFO("tmp105", 0x48),
 	},
 };
+static struct i2c_board_info __initdata sdp4430_i2c_4_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("hmc5843", 0x1e),
+	},
+};
 static int __init omap4_i2c_init(void)
 {
 	/*
@@ -423,14 +476,36 @@ static int __init omap4_i2c_init(void)
 	omap_register_i2c_bus(2, 400, NULL, 0);
 	omap_register_i2c_bus(3, 400, sdp4430_i2c_3_boardinfo,
 				ARRAY_SIZE(sdp4430_i2c_3_boardinfo));
-	omap_register_i2c_bus(4, 400, NULL, 0);
+	omap_register_i2c_bus(4, 400, sdp4430_i2c_4_boardinfo,
+				ARRAY_SIZE(sdp4430_i2c_4_boardinfo));
 	return 0;
 }
+
+static void __init omap_sfh7741prox_init(void)
+{
+	int  error;
+
+	error = gpio_request(OMAP4_SFH7741_ENABLE_GPIO, "sfh7741");
+	if (error < 0) {
+		pr_err("%s:failed to request GPIO %d, error %d\n",
+			__func__, OMAP4_SFH7741_ENABLE_GPIO, error);
+		return;
+	}
+
+	error = gpio_direction_output(OMAP4_SFH7741_ENABLE_GPIO , 0);
+	if (error < 0) {
+		pr_err("%s: GPIO configuration failed: GPIO %d,error %d\n",
+			 __func__, OMAP4_SFH7741_ENABLE_GPIO, error);
+		gpio_free(OMAP4_SFH7741_ENABLE_GPIO);
+	}
+}
+
 static void __init omap_4430sdp_init(void)
 {
 	int status;
 
 	omap4_i2c_init();
+	omap_sfh7741prox_init();
 	platform_add_devices(sdp4430_devices, ARRAY_SIZE(sdp4430_devices));
 	omap_serial_init();
 	omap4_twl6030_hsmmc_init(mmc);

arch/arm/mach-omap2/board-am3517evm.c

@@ -33,11 +33,11 @@
 
 #include <plat/board.h>
 #include <plat/common.h>
-#include <plat/control.h>
 #include <plat/usb.h>
 #include <plat/display.h>
 
 #include "mux.h"
+#include "control.h"
 
 #define AM35XX_EVM_MDIO_FREQUENCY	(1000000)
 
@@ -125,7 +125,7 @@ static void am3517_disable_ethernet_int(void)
 	regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
 }
 
-void am3517_evm_ethernet_init(struct emac_platform_data *pdata)
+static void am3517_evm_ethernet_init(struct emac_platform_data *pdata)
 {
 	unsigned int regval;
 
@@ -160,7 +160,6 @@ void am3517_evm_ethernet_init(struct emac_platform_data *pdata)
 static struct i2c_board_info __initdata am3517evm_i2c1_boardinfo[] = {
 	{
 		I2C_BOARD_INFO("s35390a", 0x30),
-		.type		= "s35390a",
 	},
 };
 
@@ -368,7 +367,7 @@ static struct omap_dss_board_info am3517_evm_dss_data = {
 	.default_device	= &am3517_evm_lcd_device,
 };
 
-struct platform_device am3517_evm_dss_device = {
+static struct platform_device am3517_evm_dss_device = {
 	.name		= "omapdss",
 	.id		= -1,
 	.dev		= {

arch/arm/mach-omap2/board-apollon.c

@@ -39,9 +39,9 @@
 #include <plat/board.h>
 #include <plat/common.h>
 #include <plat/gpmc.h>
-#include <plat/control.h>
 
 #include "mux.h"
+#include "control.h"
 
 /* LED & Switch macros */
 #define LED0_GPIO13		13

arch/arm/mach-omap2/board-cm-t35.c

@@ -31,6 +31,7 @@
 #include <linux/i2c/at24.h>
 #include <linux/i2c/twl.h>
 #include <linux/regulator/machine.h>
+#include <linux/mmc/host.h>
 
 #include <linux/spi/spi.h>
 #include <linux/spi/tdo24m.h>
@@ -237,8 +238,6 @@ static inline void cm_t35_init_nand(void) {}
 	defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
 #include <linux/spi/ads7846.h>
 
-#include <plat/mcspi.h>
-
 static struct omap2_mcspi_device_config ads7846_mcspi_config = {
 	.turbo_mode	= 0,
 	.single_channel	= 1,	/* 0: slave, 1: master */
@@ -558,7 +557,7 @@ static struct twl4030_usb_data cm_t35_usb_data = {
 	.usb_mode	= T2_USB_MODE_ULPI,
 };
 
-static int cm_t35_keymap[] = {
+static uint32_t cm_t35_keymap[] = {
 	KEY(0, 0, KEY_A),	KEY(0, 1, KEY_B),	KEY(0, 2, KEY_LEFT),
 	KEY(1, 0, KEY_UP),	KEY(1, 1, KEY_ENTER),	KEY(1, 2, KEY_DOWN),
 	KEY(2, 0, KEY_RIGHT),	KEY(2, 1, KEY_C),	KEY(2, 2, KEY_D),
@@ -579,14 +578,14 @@ static struct twl4030_keypad_data cm_t35_kp_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 
 	},
 	{
 		.mmc		= 2,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.transceiver	= 1,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,

arch/arm/mach-omap2/board-cm-t3517.c

+/*
+ * linux/arch/arm/mach-omap2/board-cm-t3517.c
+ *
+ * Support for the CompuLab CM-T3517 modules
+ *
+ * Copyright (C) 2010 CompuLab, Ltd.
+ * Author: Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/rtc-v3020.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/can/platform/ti_hecc.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <plat/board.h>
+#include <plat/common.h>
+#include <plat/usb.h>
+#include <plat/nand.h>
+#include <plat/gpmc.h>
+
+#include <mach/am35xx.h>
+
+#include "mux.h"
+#include "control.h"
+
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+static struct gpio_led cm_t3517_leds[] = {
+	[0] = {
+		.gpio			= 186,
+		.name			= "cm-t3517:green",
+		.default_trigger	= "heartbeat",
+		.active_low		= 0,
+	},
+};
+
+static struct gpio_led_platform_data cm_t3517_led_pdata = {
+	.num_leds	= ARRAY_SIZE(cm_t3517_leds),
+	.leds		= cm_t3517_leds,
+};
+
+static struct platform_device cm_t3517_led_device = {
+	.name		= "leds-gpio",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &cm_t3517_led_pdata,
+	},
+};
+
+static void __init cm_t3517_init_leds(void)
+{
+	platform_device_register(&cm_t3517_led_device);
+}
+#else
+static inline void cm_t3517_init_leds(void) {}
+#endif
+
+#if defined(CONFIG_CAN_TI_HECC) || defined(CONFIG_CAN_TI_HECC_MODULE)
+static struct resource cm_t3517_hecc_resources[] = {
+	{
+		.start	= AM35XX_IPSS_HECC_BASE,
+		.end	= AM35XX_IPSS_HECC_BASE + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= INT_35XX_HECC0_IRQ,
+		.end	= INT_35XX_HECC0_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct ti_hecc_platform_data cm_t3517_hecc_pdata = {
+	.scc_hecc_offset	= AM35XX_HECC_SCC_HECC_OFFSET,
+	.scc_ram_offset		= AM35XX_HECC_SCC_RAM_OFFSET,
+	.hecc_ram_offset	= AM35XX_HECC_RAM_OFFSET,
+	.mbx_offset		= AM35XX_HECC_MBOX_OFFSET,
+	.int_line		= AM35XX_HECC_INT_LINE,
+	.version		= AM35XX_HECC_VERSION,
+};
+
+static struct platform_device cm_t3517_hecc_device = {
+	.name		= "ti_hecc",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(cm_t3517_hecc_resources),
+	.resource	= cm_t3517_hecc_resources,
+	.dev		= {
+		.platform_data	= &cm_t3517_hecc_pdata,
+	},
+};
+
+static void cm_t3517_init_hecc(void)
+{
+	platform_device_register(&cm_t3517_hecc_device);
+}
+#else
+static inline void cm_t3517_init_hecc(void) {}
+#endif
+
+#if defined(CONFIG_RTC_DRV_V3020) || defined(CONFIG_RTC_DRV_V3020_MODULE)
+#define RTC_IO_GPIO		(153)
+#define RTC_WR_GPIO		(154)
+#define RTC_RD_GPIO		(160)
+#define RTC_CS_GPIO		(163)
+
+struct v3020_platform_data cm_t3517_v3020_pdata = {
+	.use_gpio	= 1,
+	.gpio_cs	= RTC_CS_GPIO,
+	.gpio_wr	= RTC_WR_GPIO,
+	.gpio_rd	= RTC_RD_GPIO,
+	.gpio_io	= RTC_IO_GPIO,
+};
+
+static struct platform_device cm_t3517_rtc_device = {
+	.name		= "v3020",
+	.id		= -1,
+	.dev		= {
+		.platform_data = &cm_t3517_v3020_pdata,
+	}
+};
+
+static void __init cm_t3517_init_rtc(void)
+{
+	platform_device_register(&cm_t3517_rtc_device);
+}
+#else
+static inline void cm_t3517_init_rtc(void) {}
+#endif
+
+#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_EHCI_HCD_MODULE)
+#define HSUSB1_RESET_GPIO	(146)
+#define HSUSB2_RESET_GPIO	(147)
+#define USB_HUB_RESET_GPIO	(152)
+
+static struct ehci_hcd_omap_platform_data cm_t3517_ehci_pdata __initdata = {
+	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+	.phy_reset  = true,
+	.reset_gpio_port[0]  = HSUSB1_RESET_GPIO,
+	.reset_gpio_port[1]  = HSUSB2_RESET_GPIO,
+	.reset_gpio_port[2]  = -EINVAL,
+};
+
+static int cm_t3517_init_usbh(void)
+{
+	int err;
+
+	err = gpio_request(USB_HUB_RESET_GPIO, "usb hub rst");
+	if (err) {
+		pr_err("CM-T3517: usb hub rst gpio request failed: %d\n", err);
+	} else {
+		gpio_direction_output(USB_HUB_RESET_GPIO, 0);
+		udelay(10);
+		gpio_set_value(USB_HUB_RESET_GPIO, 1);
+		msleep(1);
+	}
+
+	usb_ehci_init(&cm_t3517_ehci_pdata);
+
+	return 0;
+}
+#else
+static inline int cm_t3517_init_usbh(void)
+{
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
+#define NAND_BLOCK_SIZE		SZ_128K
+
+static struct mtd_partition cm_t3517_nand_partitions[] = {
+	{
+		.name           = "xloader",
+		.offset         = 0,			/* Offset = 0x00000 */
+		.size           = 4 * NAND_BLOCK_SIZE,
+		.mask_flags     = MTD_WRITEABLE
+	},
+	{
+		.name           = "uboot",
+		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
+		.size           = 15 * NAND_BLOCK_SIZE,
+	},
+	{
+		.name           = "uboot environment",
+		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
+		.size           = 2 * NAND_BLOCK_SIZE,
+	},
+	{
+		.name           = "linux",
+		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
+		.size           = 32 * NAND_BLOCK_SIZE,
+	},
+	{
+		.name           = "rootfs",
+		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x680000 */
+		.size           = MTDPART_SIZ_FULL,
+	},
+};
+
+static struct omap_nand_platform_data cm_t3517_nand_data = {
+	.parts			= cm_t3517_nand_partitions,
+	.nr_parts		= ARRAY_SIZE(cm_t3517_nand_partitions),
+	.dma_channel		= -1,	/* disable DMA in OMAP NAND driver */
+	.cs			= 0,
+};
+
+static void __init cm_t3517_init_nand(void)
+{
+	if (gpmc_nand_init(&cm_t3517_nand_data) < 0)
+		pr_err("CM-T3517: NAND initialization failed\n");
+}
+#else
+static inline void cm_t3517_init_nand(void) {}
+#endif
+
+static struct omap_board_config_kernel cm_t3517_config[] __initdata = {
+};
+
+static void __init cm_t3517_init_irq(void)
+{
+	omap_board_config = cm_t3517_config;
+	omap_board_config_size = ARRAY_SIZE(cm_t3517_config);
+
+	omap2_init_common_hw(NULL, NULL);
+	omap_init_irq();
+	omap_gpio_init();
+}
+
+static struct omap_board_mux board_mux[] __initdata = {
+	/* GPIO186 - Green LED */
+	OMAP3_MUX(SYS_CLKOUT2, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
+	/* RTC GPIOs: IO, WR#, RD#, CS# */
+	OMAP3_MUX(MCBSP4_DR, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
+	OMAP3_MUX(MCBSP4_DX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
+	OMAP3_MUX(MCBSP_CLKS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
+	OMAP3_MUX(UART3_CTS_RCTX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
+	/* HSUSB1 RESET */
+	OMAP3_MUX(UART2_TX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
+	/* HSUSB2 RESET */
+	OMAP3_MUX(UART2_RX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
+	/* CM-T3517 USB HUB nRESET */
+	OMAP3_MUX(MCBSP4_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
+
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+
+static void __init cm_t3517_init(void)
+{
+	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+	omap_serial_init();
+	cm_t3517_init_leds();
+	cm_t3517_init_nand();
+	cm_t3517_init_rtc();
+	cm_t3517_init_usbh();
+	cm_t3517_init_hecc();
+}
+
+MACHINE_START(CM_T3517, "Compulab CM-T3517")
+	.boot_params	= 0x80000100,
+	.map_io		= omap3_map_io,
+	.reserve        = omap_reserve,
+	.init_irq	= cm_t3517_init_irq,
+	.init_machine	= cm_t3517_init,
+	.timer		= &omap_timer,
+MACHINE_END

arch/arm/mach-omap2/board-devkit8000.c

@@ -28,6 +28,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand.h>
+#include <linux/mmc/host.h>
 
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
@@ -44,7 +45,6 @@
 #include <plat/gpmc.h>
 #include <plat/nand.h>
 #include <plat/usb.h>
-#include <plat/timer-gp.h>
 #include <plat/display.h>
 
 #include <plat/mcspi.h>
@@ -58,6 +58,7 @@
 
 #include "mux.h"
 #include "hsmmc.h"
+#include "timer-gp.h"
 
 #define NAND_BLOCK_SIZE		SZ_128K
 
@@ -105,7 +106,7 @@ static struct omap_nand_platform_data devkit8000_nand_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 29,
 	},
 	{}	/* Terminator */
@@ -198,7 +199,7 @@ static struct platform_device devkit8000_dss_device = {
 static struct regulator_consumer_supply devkit8000_vdda_dac_supply =
 	REGULATOR_SUPPLY("vdda_dac", "omapdss");
 
-static int board_keymap[] = {
+static uint32_t board_keymap[] = {
 	KEY(0, 0, KEY_1),
 	KEY(1, 0, KEY_2),
 	KEY(2, 0, KEY_3),

arch/arm/mach-omap2/board-flash.c

@@ -21,7 +21,8 @@
 #include <plat/nand.h>
 #include <plat/onenand.h>
 #include <plat/tc.h>
-#include <mach/board-flash.h>
+
+#include "board-flash.h"
 
 #define REG_FPGA_REV			0x10
 #define REG_FPGA_DIP_SWITCH_INPUT2	0x60

arch/arm/mach-omap2/include/mach/board-flash.h → arch/arm/mach-omap2/board-flash.h

@@ -26,3 +26,5 @@ struct flash_partitions {
 
 extern void board_flash_init(struct flash_partitions [],
 				char chip_sel[][GPMC_CS_NUM]);
+extern void board_nand_init(struct mtd_partition *nand_parts,
+					u8 nr_parts, u8 cs);

arch/arm/mach-omap2/board-generic.c

@@ -48,10 +48,22 @@ static void __init omap_generic_init(void)
 
 static void __init omap_generic_map_io(void)
 {
-	omap2_set_globals_242x(); /* should be 242x, 243x, or 343x */
-	omap242x_map_common_io();
+	if (cpu_is_omap242x()) {
+		omap2_set_globals_242x();
+		omap242x_map_common_io();
+	} else if (cpu_is_omap243x()) {
+		omap2_set_globals_243x();
+		omap243x_map_common_io();
+	} else if (cpu_is_omap34xx()) {
+		omap2_set_globals_3xxx();
+		omap34xx_map_common_io();
+	} else if (cpu_is_omap44xx()) {
+		omap2_set_globals_443x();
+		omap44xx_map_common_io();
+	}
 }
 
+/* XXX This machine entry name should be updated */
 MACHINE_START(OMAP_GENERIC, "Generic OMAP24xx")
 	/* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
 	.boot_params	= 0x80000100,

arch/arm/mach-omap2/board-h4.c

@@ -31,7 +31,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/control.h>
 #include <mach/gpio.h>
 #include <plat/usb.h>
 #include <plat/board.h>
@@ -42,6 +41,7 @@
 #include <plat/gpmc.h>
 
 #include "mux.h"
+#include "control.h"
 
 #define H4_FLASH_CS	0
 #define H4_SMC91X_CS	1

arch/arm/mach-omap2/board-igep0020.c

@@ -20,6 +20,7 @@
 
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
+#include <linux/mmc/host.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -38,12 +39,61 @@
 #define IGEP2_SMSC911X_CS       5
 #define IGEP2_SMSC911X_GPIO     176
 #define IGEP2_GPIO_USBH_NRESET  24
-#define IGEP2_GPIO_LED0_GREEN 	26
-#define IGEP2_GPIO_LED0_RED 	27
-#define IGEP2_GPIO_LED1_RED   	28
-#define IGEP2_GPIO_DVI_PUP	170
-#define IGEP2_GPIO_WIFI_NPD 	94
-#define IGEP2_GPIO_WIFI_NRESET 	95
+#define IGEP2_GPIO_LED0_GREEN   26
+#define IGEP2_GPIO_LED0_RED     27
+#define IGEP2_GPIO_LED1_RED     28
+#define IGEP2_GPIO_DVI_PUP      170
+
+#define IGEP2_RB_GPIO_WIFI_NPD     94
+#define IGEP2_RB_GPIO_WIFI_NRESET  95
+#define IGEP2_RB_GPIO_BT_NRESET    137
+#define IGEP2_RC_GPIO_WIFI_NPD     138
+#define IGEP2_RC_GPIO_WIFI_NRESET  139
+#define IGEP2_RC_GPIO_BT_NRESET    137
+
+/*
+ * IGEP2 Hardware Revision Table
+ *
+ *  --------------------------------------------------------------------------
+ * | Id. | Hw Rev.            | HW0 (28) | WIFI_NPD | WIFI_NRESET | BT_NRESET |
+ *  --------------------------------------------------------------------------
+ * |  0  | B                  |   high   |  gpio94  |   gpio95    |     -     |
+ * |  0  | B/C (B-compatible) |   high   |  gpio94  |   gpio95    |  gpio137  |
+ * |  1  | C                  |   low    |  gpio138 |   gpio139   |  gpio137  |
+ *  --------------------------------------------------------------------------
+ */
+
+#define IGEP2_BOARD_HWREV_B	0
+#define IGEP2_BOARD_HWREV_C	1
+
+static u8 hwrev;
+
+static void __init igep2_get_revision(void)
+{
+	u8 ret;
+
+	omap_mux_init_gpio(IGEP2_GPIO_LED1_RED, OMAP_PIN_INPUT);
+
+	if ((gpio_request(IGEP2_GPIO_LED1_RED, "GPIO_HW0_REV") == 0) &&
+	    (gpio_direction_input(IGEP2_GPIO_LED1_RED) == 0)) {
+		ret = gpio_get_value(IGEP2_GPIO_LED1_RED);
+		if (ret == 0) {
+			pr_info("IGEP2: Hardware Revision C (B-NON compatible)\n");
+			hwrev = IGEP2_BOARD_HWREV_C;
+		} else if (ret ==  1) {
+			pr_info("IGEP2: Hardware Revision B/C (B compatible)\n");
+			hwrev = IGEP2_BOARD_HWREV_B;
+		} else {
+			pr_err("IGEP2: Unknown Hardware Revision\n");
+			hwrev = -1;
+		}
+	} else {
+		pr_warning("IGEP2: Could not obtain gpio GPIO_HW0_REV\n");
+		pr_err("IGEP2: Unknown Hardware Revision\n");
+	}
+
+	gpio_free(IGEP2_GPIO_LED1_RED);
+}
 
 #if defined(CONFIG_MTD_ONENAND_OMAP2) || \
 	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
@@ -107,7 +157,7 @@ static struct platform_device igep2_onenand_device = {
 	},
 };
 
-void __init igep2_flash_init(void)
+static void __init igep2_flash_init(void)
 {
 	u8		cs = 0;
 	u8		onenandcs = GPMC_CS_NUM + 1;
@@ -141,7 +191,7 @@ void __init igep2_flash_init(void)
 }
 
 #else
-void __init igep2_flash_init(void) {}
+static void __init igep2_flash_init(void) {}
 #endif
 
 #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
@@ -211,10 +261,6 @@ static struct regulator_consumer_supply igep2_vmmc1_supply = {
 	.supply		= "vmmc",
 };
 
-static struct regulator_consumer_supply igep2_vmmc2_supply = {
-	.supply		= "vmmc",
-};
-
 /* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
 static struct regulator_init_data igep2_vmmc1 = {
 	.constraints = {
@@ -230,37 +276,95 @@ static struct regulator_init_data igep2_vmmc1 = {
 	.consumer_supplies      = &igep2_vmmc1_supply,
 };
 
-/* VMMC2 for OMAP VDD_MMC2 (i/o) and MMC2 WIFI */
-static struct regulator_init_data igep2_vmmc2 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = 1,
-	.consumer_supplies      = &igep2_vmmc2_supply,
-};
-
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 	},
+#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
 	{
 		.mmc		= 2,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 	},
+#endif
 	{}      /* Terminator */
 };
 
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+#include <linux/leds.h>
+
+static struct gpio_led igep2_gpio_leds[] = {
+	[0] = {
+		.name			= "gpio-led:red:d0",
+		.gpio			= IGEP2_GPIO_LED0_RED,
+		.default_trigger	= "default-off"
+	},
+	[1] = {
+		.name			= "gpio-led:green:d0",
+		.gpio			= IGEP2_GPIO_LED0_GREEN,
+		.default_trigger	= "default-off",
+	},
+	[2] = {
+		.name			= "gpio-led:red:d1",
+		.gpio			= IGEP2_GPIO_LED1_RED,
+		.default_trigger	= "default-off",
+	},
+	[3] = {
+		.name			= "gpio-led:green:d1",
+		.default_trigger	= "heartbeat",
+		.gpio			= -EINVAL, /* gets replaced */
+	},
+};
+
+static struct gpio_led_platform_data igep2_led_pdata = {
+	.leds           = igep2_gpio_leds,
+	.num_leds       = ARRAY_SIZE(igep2_gpio_leds),
+};
+
+static struct platform_device igep2_led_device = {
+	 .name   = "leds-gpio",
+	 .id     = -1,
+	 .dev    = {
+		 .platform_data  =  &igep2_led_pdata,
+	},
+};
+
+static void __init igep2_leds_init(void)
+{
+	platform_device_register(&igep2_led_device);
+}
+
+#else
+static inline void igep2_leds_init(void)
+{
+	if ((gpio_request(IGEP2_GPIO_LED0_RED, "gpio-led:red:d0") == 0) &&
+	    (gpio_direction_output(IGEP2_GPIO_LED0_RED, 1) == 0)) {
+		gpio_export(IGEP2_GPIO_LED0_RED, 0);
+		gpio_set_value(IGEP2_GPIO_LED0_RED, 0);
+	} else
+		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_RED\n");
+
+	if ((gpio_request(IGEP2_GPIO_LED0_GREEN, "gpio-led:green:d0") == 0) &&
+	    (gpio_direction_output(IGEP2_GPIO_LED0_GREEN, 1) == 0)) {
+		gpio_export(IGEP2_GPIO_LED0_GREEN, 0);
+		gpio_set_value(IGEP2_GPIO_LED0_GREEN, 0);
+	} else
+		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_GREEN\n");
+
+	if ((gpio_request(IGEP2_GPIO_LED1_RED, "gpio-led:red:d1") == 0) &&
+	    (gpio_direction_output(IGEP2_GPIO_LED1_RED, 1) == 0)) {
+		gpio_export(IGEP2_GPIO_LED1_RED, 0);
+		gpio_set_value(IGEP2_GPIO_LED1_RED, 0);
+	} else
+		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
+
+}
+#endif
+
 static int igep2_twl_gpio_setup(struct device *dev,
 		unsigned gpio, unsigned ngpio)
 {
@@ -268,20 +372,48 @@ static int igep2_twl_gpio_setup(struct device *dev,
 	mmc[0].gpio_cd = gpio + 0;
 	omap2_hsmmc_init(mmc);
 
-	/* link regulators to MMC adapters ... we "know" the
+	/*
+	 * link regulators to MMC adapters ... we "know" the
 	 * regulators will be set up only *after* we return.
-	*/
+	 */
 	igep2_vmmc1_supply.dev = mmc[0].dev;
-	igep2_vmmc2_supply.dev = mmc[1].dev;
+
+	/*
+	 * REVISIT: need ehci-omap hooks for external VBUS
+	 * power switch and overcurrent detect
+	 */
+	if ((gpio_request(gpio + 1, "GPIO_EHCI_NOC") < 0) ||
+	    (gpio_direction_input(gpio + 1) < 0))
+		pr_err("IGEP2: Could not obtain gpio for EHCI NOC");
+
+	/*
+	 * TWL4030_GPIO_MAX + 0 == ledA, GPIO_USBH_CPEN
+	 * (out, active low)
+	 */
+	if ((gpio_request(gpio + TWL4030_GPIO_MAX, "GPIO_USBH_CPEN") < 0) ||
+	    (gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0) < 0))
+		pr_err("IGEP2: Could not obtain gpio for USBH_CPEN");
+
+	/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
+#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
+	if ((gpio_request(gpio+TWL4030_GPIO_MAX+1, "gpio-led:green:d1") == 0)
+	    && (gpio_direction_output(gpio + TWL4030_GPIO_MAX + 1, 1) == 0)) {
+		gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
+		gpio_set_value(gpio + TWL4030_GPIO_MAX + 1, 0);
+	} else
+		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_GREEN\n");
+#else
+	igep2_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
+#endif
 
 	return 0;
 };
 
-static struct twl4030_gpio_platform_data igep2_gpio_data = {
+static struct twl4030_gpio_platform_data igep2_twl4030_gpio_pdata = {
 	.gpio_base	= OMAP_MAX_GPIO_LINES,
 	.irq_base	= TWL4030_GPIO_IRQ_BASE,
 	.irq_end	= TWL4030_GPIO_IRQ_END,
-	.use_leds	= false,
+	.use_leds	= true,
 	.setup		= igep2_twl_gpio_setup,
 };
 
@@ -355,47 +487,6 @@ static void __init igep2_display_init(void)
 		pr_err("IGEP v2: Could not obtain gpio GPIO_DVI_PUP\n");
 }
 
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
-#include <linux/leds.h>
-
-static struct gpio_led igep2_gpio_leds[] = {
-	{
-		.name = "led0:red",
-		.gpio = IGEP2_GPIO_LED0_RED,
-	},
-	{
-		.name = "led0:green",
-		.default_trigger = "heartbeat",
-		.gpio = IGEP2_GPIO_LED0_GREEN,
-	},
-	{
-		.name = "led1:red",
-		.gpio = IGEP2_GPIO_LED1_RED,
-	},
-};
-
-static struct gpio_led_platform_data igep2_led_pdata = {
-	.leds           = igep2_gpio_leds,
-	.num_leds       = ARRAY_SIZE(igep2_gpio_leds),
-};
-
-static struct platform_device igep2_led_device = {
-	 .name   = "leds-gpio",
-	 .id     = -1,
-	 .dev    = {
-		 .platform_data  =  &igep2_led_pdata,
-	},
-};
-
-static void __init igep2_init_led(void)
-{
-	platform_device_register(&igep2_led_device);
-}
-
-#else
-static inline void igep2_init_led(void) {}
-#endif
-
 static struct platform_device *igep2_devices[] __initdata = {
 	&igep2_dss_device,
 };
@@ -425,14 +516,13 @@ static struct twl4030_platform_data igep2_twldata = {
 	/* platform_data for children goes here */
 	.usb		= &igep2_usb_data,
 	.codec		= &igep2_codec_data,
-	.gpio		= &igep2_gpio_data,
+	.gpio		= &igep2_twl4030_gpio_pdata,
 	.vmmc1          = &igep2_vmmc1,
-	.vmmc2		= &igep2_vmmc2,
 	.vpll2		= &igep2_vpll2,
 
 };
 
-static struct i2c_board_info __initdata igep2_i2c_boardinfo[] = {
+static struct i2c_board_info __initdata igep2_i2c1_boardinfo[] = {
 	{
 		I2C_BOARD_INFO("twl4030", 0x48),
 		.flags		= I2C_CLIENT_WAKE,
@@ -441,14 +531,29 @@ static struct i2c_board_info __initdata igep2_i2c_boardinfo[] = {
 	},
 };
 
-static int __init igep2_i2c_init(void)
+static struct i2c_board_info __initdata igep2_i2c3_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("eeprom", 0x50),
+	},
+};
+
+static void __init igep2_i2c_init(void)
 {
-	omap_register_i2c_bus(1, 2600, igep2_i2c_boardinfo,
-			ARRAY_SIZE(igep2_i2c_boardinfo));
-	/* Bus 3 is attached to the DVI port where devices like the pico DLP
-	 * projector don't work reliably with 400kHz */
-	omap_register_i2c_bus(3, 100, NULL, 0);
-	return 0;
+	int ret;
+
+	ret = omap_register_i2c_bus(1, 2600, igep2_i2c1_boardinfo,
+		ARRAY_SIZE(igep2_i2c1_boardinfo));
+	if (ret)
+		pr_warning("IGEP2: Could not register I2C1 bus (%d)\n", ret);
+
+	/*
+	 * Bus 3 is attached to the DVI port where devices like the pico DLP
+	 * projector don't work reliably with 400kHz
+	 */
+	ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
+		ARRAY_SIZE(igep2_i2c3_boardinfo));
+	if (ret)
+		pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
 }
 
 static struct omap_musb_board_data musb_board_data = {
@@ -476,9 +581,57 @@ static struct omap_board_mux board_mux[] __initdata = {
 #define board_mux	NULL
 #endif
 
+#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
+
+static void __init igep2_wlan_bt_init(void)
+{
+	unsigned npd, wreset, btreset;
+
+	/* GPIO's for WLAN-BT combo depends on hardware revision */
+	if (hwrev == IGEP2_BOARD_HWREV_B) {
+		npd = IGEP2_RB_GPIO_WIFI_NPD;
+		wreset = IGEP2_RB_GPIO_WIFI_NRESET;
+		btreset = IGEP2_RB_GPIO_BT_NRESET;
+	} else if (hwrev == IGEP2_BOARD_HWREV_C) {
+		npd = IGEP2_RC_GPIO_WIFI_NPD;
+		wreset = IGEP2_RC_GPIO_WIFI_NRESET;
+		btreset = IGEP2_RC_GPIO_BT_NRESET;
+	} else
+		return;
+
+	/* Set GPIO's for  WLAN-BT combo module */
+	if ((gpio_request(npd, "GPIO_WIFI_NPD") == 0) &&
+	    (gpio_direction_output(npd, 1) == 0)) {
+		gpio_export(npd, 0);
+	} else
+		pr_warning("IGEP2: Could not obtain gpio GPIO_WIFI_NPD\n");
+
+	if ((gpio_request(wreset, "GPIO_WIFI_NRESET") == 0) &&
+	    (gpio_direction_output(wreset, 1) == 0)) {
+		gpio_export(wreset, 0);
+		gpio_set_value(wreset, 0);
+		udelay(10);
+		gpio_set_value(wreset, 1);
+	} else
+		pr_warning("IGEP2: Could not obtain gpio GPIO_WIFI_NRESET\n");
+
+	if ((gpio_request(btreset, "GPIO_BT_NRESET") == 0) &&
+	    (gpio_direction_output(btreset, 1) == 0)) {
+		gpio_export(btreset, 0);
+	} else
+		pr_warning("IGEP2: Could not obtain gpio GPIO_BT_NRESET\n");
+}
+#else
+static inline void __init igep2_wlan_bt_init(void) { }
+#endif
+
 static void __init igep2_init(void)
 {
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+
+	/* Get IGEP2 hardware revision */
+	igep2_get_revision();
+	/* Register I2C busses and drivers */
 	igep2_i2c_init();
 	platform_add_devices(igep2_devices, ARRAY_SIZE(igep2_devices));
 	omap_serial_init();
@@ -486,50 +639,16 @@ static void __init igep2_init(void)
 	usb_ehci_init(&ehci_pdata);
 
 	igep2_flash_init();
-	igep2_init_led();
+	igep2_leds_init();
 	igep2_display_init();
 	igep2_init_smsc911x();
 
-	/* GPIO userspace leds */
-#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
-	if ((gpio_request(IGEP2_GPIO_LED0_RED, "led0:red") == 0) &&
-	    (gpio_direction_output(IGEP2_GPIO_LED0_RED, 1) == 0)) {
-		gpio_export(IGEP2_GPIO_LED0_RED, 0);
-		gpio_set_value(IGEP2_GPIO_LED0_RED, 0);
-	} else
-		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_RED\n");
-
-	if ((gpio_request(IGEP2_GPIO_LED0_GREEN, "led0:green") == 0) &&
-	    (gpio_direction_output(IGEP2_GPIO_LED0_GREEN, 1) == 0)) {
-		gpio_export(IGEP2_GPIO_LED0_GREEN, 0);
-		gpio_set_value(IGEP2_GPIO_LED0_GREEN, 0);
-	} else
-		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_GREEN\n");
-
-	if ((gpio_request(IGEP2_GPIO_LED1_RED, "led1:red") == 0) &&
-	    (gpio_direction_output(IGEP2_GPIO_LED1_RED, 1) == 0)) {
-		gpio_export(IGEP2_GPIO_LED1_RED, 0);
-		gpio_set_value(IGEP2_GPIO_LED1_RED, 0);
-	} else
-		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
-#endif
-
-	/* GPIO W-LAN + Bluetooth combo module */
-	if ((gpio_request(IGEP2_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
-	    (gpio_direction_output(IGEP2_GPIO_WIFI_NPD, 1) == 0)) {
-		gpio_export(IGEP2_GPIO_WIFI_NPD, 0);
-/* 		gpio_set_value(IGEP2_GPIO_WIFI_NPD, 0); */
-	} else
-		pr_warning("IGEP v2: Could not obtain gpio GPIO_WIFI_NPD\n");
+	/*
+	 * WLAN-BT combo module from MuRata wich has a Marvell WLAN
+	 * (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
+	 */
+	igep2_wlan_bt_init();
 
-	if ((gpio_request(IGEP2_GPIO_WIFI_NRESET, "GPIO_WIFI_NRESET") == 0) &&
-	    (gpio_direction_output(IGEP2_GPIO_WIFI_NRESET, 1) == 0)) {
-		gpio_export(IGEP2_GPIO_WIFI_NRESET, 0);
-		gpio_set_value(IGEP2_GPIO_WIFI_NRESET, 0);
-		udelay(10);
-		gpio_set_value(IGEP2_GPIO_WIFI_NRESET, 1);
-	} else
-		pr_warning("IGEP v2: Could not obtain gpio GPIO_WIFI_NRESET\n");
 }
 
 MACHINE_START(IGEP0020, "IGEP v2 board")

arch/arm/mach-omap2/board-igep0030.c

+/*
+ * Copyright (C) 2010 - ISEE 2007 SL
+ *
+ * Modified from mach-omap2/board-generic.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+
+#include <linux/regulator/machine.h>
+#include <linux/i2c/twl.h>
+#include <linux/mmc/host.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <plat/board.h>
+#include <plat/common.h>
+#include <plat/gpmc.h>
+#include <plat/usb.h>
+#include <plat/onenand.h>
+
+#include "mux.h"
+#include "hsmmc.h"
+#include "sdram-numonyx-m65kxxxxam.h"
+
+#define IGEP3_GPIO_LED0_GREEN	54
+#define IGEP3_GPIO_LED0_RED	53
+#define IGEP3_GPIO_LED1_RED	16
+
+#define IGEP3_GPIO_WIFI_NPD	138
+#define IGEP3_GPIO_WIFI_NRESET	139
+#define IGEP3_GPIO_BT_NRESET	137
+
+#define IGEP3_GPIO_USBH_NRESET  115
+
+
+#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
+	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+
+#define ONENAND_MAP             0x20000000
+
+/*
+ * x2 Flash built-in COMBO POP MEMORY
+ * Since the device is equipped with two DataRAMs, and two-plane NAND
+ * Flash memory array, these two component enables simultaneous program
+ * of 4KiB. Plane1 has only even blocks such as block0, block2, block4
+ * while Plane2 has only odd blocks such as block1, block3, block5.
+ * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
+ */
+
+static struct mtd_partition igep3_onenand_partitions[] = {
+	{
+		.name           = "X-Loader",
+		.offset         = 0,
+		.size           = 2 * (64*(2*2048))
+	},
+	{
+		.name           = "U-Boot",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 6 * (64*(2*2048)),
+	},
+	{
+		.name           = "Environment",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 2 * (64*(2*2048)),
+	},
+	{
+		.name           = "Kernel",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 12 * (64*(2*2048)),
+	},
+	{
+		.name           = "File System",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = MTDPART_SIZ_FULL,
+	},
+};
+
+static struct omap_onenand_platform_data igep3_onenand_pdata = {
+	.parts = igep3_onenand_partitions,
+	.nr_parts = ARRAY_SIZE(igep3_onenand_partitions),
+	.onenand_setup = NULL,
+	.dma_channel	= -1,	/* disable DMA in OMAP OneNAND driver */
+};
+
+static struct platform_device igep3_onenand_device = {
+	.name		= "omap2-onenand",
+	.id		= -1,
+	.dev = {
+		.platform_data = &igep3_onenand_pdata,
+	},
+};
+
+void __init igep3_flash_init(void)
+{
+	u8 cs = 0;
+	u8 onenandcs = GPMC_CS_NUM + 1;
+
+	for (cs = 0; cs < GPMC_CS_NUM; cs++) {
+		u32 ret;
+		ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
+
+		/* Check if NAND/oneNAND is configured */
+		if ((ret & 0xC00) == 0x800)
+			/* NAND found */
+			pr_err("IGEP3: Unsupported NAND found\n");
+		else {
+			ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
+
+			if ((ret & 0x3F) == (ONENAND_MAP >> 24))
+				/* OneNAND found */
+				onenandcs = cs;
+		}
+	}
+
+	if (onenandcs > GPMC_CS_NUM) {
+		pr_err("IGEP3: Unable to find configuration in GPMC\n");
+		return;
+	}
+
+	igep3_onenand_pdata.cs = onenandcs;
+
+	if (platform_device_register(&igep3_onenand_device) < 0)
+		pr_err("IGEP3: Unable to register OneNAND device\n");
+}
+
+#else
+void __init igep3_flash_init(void) {}
+#endif
+
+static struct regulator_consumer_supply igep3_vmmc1_supply = {
+	.supply		= "vmmc",
+};
+
+/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
+static struct regulator_init_data igep3_vmmc1 = {
+	.constraints = {
+		.min_uV			= 1850000,
+		.max_uV			= 3150000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = &igep3_vmmc1_supply,
+};
+
+static struct omap2_hsmmc_info mmc[] = {
+	[0] = {
+		.mmc		= 1,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
+	},
+#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
+	[1] = {
+		.mmc		= 2,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
+	},
+#endif
+	{}      /* Terminator */
+};
+
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+#include <linux/leds.h>
+
+static struct gpio_led igep3_gpio_leds[] = {
+	[0] = {
+		.name			= "gpio-led:red:d0",
+		.gpio			= IGEP3_GPIO_LED0_RED,
+		.default_trigger	= "default-off"
+	},
+	[1] = {
+		.name			= "gpio-led:green:d0",
+		.gpio			= IGEP3_GPIO_LED0_GREEN,
+		.default_trigger	= "default-off",
+	},
+	[2] = {
+		.name			= "gpio-led:red:d1",
+		.gpio			= IGEP3_GPIO_LED1_RED,
+		.default_trigger	= "default-off",
+	},
+	[3] = {
+		.name			= "gpio-led:green:d1",
+		.default_trigger	= "heartbeat",
+		.gpio			= -EINVAL, /* gets replaced */
+	},
+};
+
+static struct gpio_led_platform_data igep3_led_pdata = {
+	.leds           = igep3_gpio_leds,
+	.num_leds       = ARRAY_SIZE(igep3_gpio_leds),
+};
+
+static struct platform_device igep3_led_device = {
+	 .name   = "leds-gpio",
+	 .id     = -1,
+	 .dev    = {
+		 .platform_data = &igep3_led_pdata,
+	},
+};
+
+static void __init igep3_leds_init(void)
+{
+	platform_device_register(&igep3_led_device);
+}
+
+#else
+static inline void igep3_leds_init(void)
+{
+	if ((gpio_request(IGEP3_GPIO_LED0_RED, "gpio-led:red:d0") == 0) &&
+	    (gpio_direction_output(IGEP3_GPIO_LED0_RED, 1) == 0)) {
+		gpio_export(IGEP3_GPIO_LED0_RED, 0);
+		gpio_set_value(IGEP3_GPIO_LED0_RED, 1);
+	} else
+		pr_warning("IGEP3: Could not obtain gpio GPIO_LED0_RED\n");
+
+	if ((gpio_request(IGEP3_GPIO_LED0_GREEN, "gpio-led:green:d0") == 0) &&
+	    (gpio_direction_output(IGEP3_GPIO_LED0_GREEN, 1) == 0)) {
+		gpio_export(IGEP3_GPIO_LED0_GREEN, 0);
+		gpio_set_value(IGEP3_GPIO_LED0_GREEN, 1);
+	} else
+		pr_warning("IGEP3: Could not obtain gpio GPIO_LED0_GREEN\n");
+
+	if ((gpio_request(IGEP3_GPIO_LED1_RED, "gpio-led:red:d1") == 0) &&
+		(gpio_direction_output(IGEP3_GPIO_LED1_RED, 1) == 0)) {
+		gpio_export(IGEP3_GPIO_LED1_RED, 0);
+		gpio_set_value(IGEP3_GPIO_LED1_RED, 1);
+	} else
+		pr_warning("IGEP3: Could not obtain gpio GPIO_LED1_RED\n");
+}
+#endif
+
+static int igep3_twl4030_gpio_setup(struct device *dev,
+		unsigned gpio, unsigned ngpio)
+{
+	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
+	mmc[0].gpio_cd = gpio + 0;
+	omap2_hsmmc_init(mmc);
+
+	/*
+	 * link regulators to MMC adapters ... we "know" the
+	 * regulators will be set up only *after* we return.
+	 */
+	igep3_vmmc1_supply.dev = mmc[0].dev;
+
+	/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
+#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
+	if ((gpio_request(gpio+TWL4030_GPIO_MAX+1, "gpio-led:green:d1") == 0)
+	    && (gpio_direction_output(gpio + TWL4030_GPIO_MAX + 1, 1) == 0)) {
+		gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
+		gpio_set_value(gpio + TWL4030_GPIO_MAX + 1, 0);
+	} else
+		pr_warning("IGEP3: Could not obtain gpio GPIO_LED1_GREEN\n");
+#else
+	igep3_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
+#endif
+
+	return 0;
+};
+
+static struct twl4030_gpio_platform_data igep3_twl4030_gpio_pdata = {
+	.gpio_base	= OMAP_MAX_GPIO_LINES,
+	.irq_base	= TWL4030_GPIO_IRQ_BASE,
+	.irq_end	= TWL4030_GPIO_IRQ_END,
+	.use_leds	= true,
+	.setup		= igep3_twl4030_gpio_setup,
+};
+
+static struct twl4030_usb_data igep3_twl4030_usb_data = {
+	.usb_mode	= T2_USB_MODE_ULPI,
+};
+
+static void __init igep3_init_irq(void)
+{
+	omap2_init_common_hw(m65kxxxxam_sdrc_params, m65kxxxxam_sdrc_params);
+	omap_init_irq();
+	omap_gpio_init();
+}
+
+static struct twl4030_platform_data igep3_twl4030_pdata = {
+	.irq_base	= TWL4030_IRQ_BASE,
+	.irq_end	= TWL4030_IRQ_END,
+
+	/* platform_data for children goes here */
+	.usb		= &igep3_twl4030_usb_data,
+	.gpio		= &igep3_twl4030_gpio_pdata,
+	.vmmc1		= &igep3_vmmc1,
+};
+
+static struct i2c_board_info __initdata igep3_i2c_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("twl4030", 0x48),
+		.flags		= I2C_CLIENT_WAKE,
+		.irq		= INT_34XX_SYS_NIRQ,
+		.platform_data	= &igep3_twl4030_pdata,
+	},
+};
+
+static int __init igep3_i2c_init(void)
+{
+	omap_register_i2c_bus(1, 2600, igep3_i2c_boardinfo,
+			ARRAY_SIZE(igep3_i2c_boardinfo));
+
+	return 0;
+}
+
+static struct omap_musb_board_data musb_board_data = {
+	.interface_type	= MUSB_INTERFACE_ULPI,
+	.mode		= MUSB_OTG,
+	.power		= 100,
+};
+
+#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
+
+static void __init igep3_wifi_bt_init(void)
+{
+	/* Configure MUX values for W-LAN + Bluetooth GPIO's */
+	omap_mux_init_gpio(IGEP3_GPIO_WIFI_NPD, OMAP_PIN_OUTPUT);
+	omap_mux_init_gpio(IGEP3_GPIO_WIFI_NRESET, OMAP_PIN_OUTPUT);
+	omap_mux_init_gpio(IGEP3_GPIO_BT_NRESET, OMAP_PIN_OUTPUT);
+
+	/* Set GPIO's for  W-LAN + Bluetooth combo module */
+	if ((gpio_request(IGEP3_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
+	    (gpio_direction_output(IGEP3_GPIO_WIFI_NPD, 1) == 0)) {
+		gpio_export(IGEP3_GPIO_WIFI_NPD, 0);
+	} else
+		pr_warning("IGEP3: Could not obtain gpio GPIO_WIFI_NPD\n");
+
+	if ((gpio_request(IGEP3_GPIO_WIFI_NRESET, "GPIO_WIFI_NRESET") == 0) &&
+	    (gpio_direction_output(IGEP3_GPIO_WIFI_NRESET, 1) == 0)) {
+		gpio_export(IGEP3_GPIO_WIFI_NRESET, 0);
+		gpio_set_value(IGEP3_GPIO_WIFI_NRESET, 0);
+		udelay(10);
+		gpio_set_value(IGEP3_GPIO_WIFI_NRESET, 1);
+	} else
+		pr_warning("IGEP3: Could not obtain gpio GPIO_WIFI_NRESET\n");
+
+	if ((gpio_request(IGEP3_GPIO_BT_NRESET, "GPIO_BT_NRESET") == 0) &&
+	    (gpio_direction_output(IGEP3_GPIO_BT_NRESET, 1) == 0)) {
+		gpio_export(IGEP3_GPIO_BT_NRESET, 0);
+	} else
+		pr_warning("IGEP3: Could not obtain gpio GPIO_BT_NRESET\n");
+}
+#else
+void __init igep3_wifi_bt_init(void) {}
+#endif
+
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+#else
+#define board_mux	NULL
+#endif
+
+static void __init igep3_init(void)
+{
+	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+
+	/* Register I2C busses and drivers */
+	igep3_i2c_init();
+
+	omap_serial_init();
+	usb_musb_init(&musb_board_data);
+
+	igep3_flash_init();
+	igep3_leds_init();
+
+	/*
+	 * WLAN-BT combo module from MuRata wich has a Marvell WLAN
+	 * (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
+	 */
+	igep3_wifi_bt_init();
+
+}
+
+MACHINE_START(IGEP0030, "IGEP OMAP3 module")
+	.boot_params	= 0x80000100,
+	.map_io		= omap3_map_io,
+	.init_irq	= igep3_init_irq,
+	.init_machine	= igep3_init,
+	.timer		= &omap_timer,
+MACHINE_END

arch/arm/mach-omap2/board-ldp.c

@@ -27,6 +27,7 @@
 #include <linux/i2c/twl.h>
 #include <linux/io.h>
 #include <linux/smsc911x.h>
+#include <linux/mmc/host.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -41,11 +42,12 @@
 #include <mach/board-zoom.h>
 
 #include <asm/delay.h>
-#include <plat/control.h>
 #include <plat/usb.h>
 
+#include "board-flash.h"
 #include "mux.h"
 #include "hsmmc.h"
+#include "control.h"
 
 #define LDP_SMSC911X_CS		1
 #define LDP_SMSC911X_GPIO	152
@@ -82,7 +84,7 @@ static struct platform_device ldp_smsc911x_device = {
 	},
 };
 
-static int board_keymap[] = {
+static uint32_t board_keymap[] = {
 	KEY(0, 0, KEY_1),
 	KEY(1, 0, KEY_2),
 	KEY(2, 0, KEY_3),
@@ -362,7 +364,7 @@ static int __init omap_i2c_init(void)
 static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 	},

arch/arm/mach-omap2/board-n8x0.c

@@ -20,6 +20,7 @@
 #include <linux/i2c.h>
 #include <linux/spi/spi.h>
 #include <linux/usb/musb.h>
+#include <sound/tlv320aic3x.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
@@ -383,15 +384,6 @@ static void n8x0_mmc_callback(void *data, u8 card_mask)
 	omap_mmc_notify_cover_event(mmc_device, index, *openp);
 }
 
-void n8x0_mmc_slot1_cover_handler(void *arg, int closed_state)
-{
-	if (mmc_device == NULL)
-		return;
-
-	slot1_cover_open = !closed_state;
-	omap_mmc_notify_cover_event(mmc_device, 0, closed_state);
-}
-
 static int n8x0_mmc_late_init(struct device *dev)
 {
 	int r, bit, *openp;
@@ -511,7 +503,7 @@ static struct omap_mmc_platform_data mmc1_data = {
 
 static struct omap_mmc_platform_data *mmc_data[OMAP24XX_NR_MMC];
 
-void __init n8x0_mmc_init(void)
+static void __init n8x0_mmc_init(void)
 
 {
 	int err;
@@ -560,11 +552,6 @@ void __init n8x0_mmc_init(void)
 void __init n8x0_mmc_init(void)
 {
 }
-
-void n8x0_mmc_slot1_cover_handler(void *arg, int state)
-{
-}
-
 #endif	/* CONFIG_MMC_OMAP */
 
 #ifdef CONFIG_MENELAUS
@@ -614,29 +601,35 @@ static int n8x0_menelaus_late_init(struct device *dev)
 	return 0;
 }
 
-static struct i2c_board_info __initdata n8x0_i2c_board_info_1[] = {
+#else
+static int n8x0_menelaus_late_init(struct device *dev)
+{
+	return 0;
+}
+#endif
+
+static struct menelaus_platform_data n8x0_menelaus_platform_data __initdata = {
+	.late_init = n8x0_menelaus_late_init,
+};
+
+static struct i2c_board_info __initdata n8x0_i2c_board_info_1[] __initdata = {
 	{
 		I2C_BOARD_INFO("menelaus", 0x72),
 		.irq = INT_24XX_SYS_NIRQ,
+		.platform_data = &n8x0_menelaus_platform_data,
 	},
 };
 
-static struct menelaus_platform_data n8x0_menelaus_platform_data = {
-	.late_init = n8x0_menelaus_late_init,
+static struct aic3x_pdata n810_aic33_data __initdata = {
+	.gpio_reset = 118,
 };
 
-static void __init n8x0_menelaus_init(void)
-{
-	n8x0_i2c_board_info_1[0].platform_data = &n8x0_menelaus_platform_data;
-	omap_register_i2c_bus(1, 400, n8x0_i2c_board_info_1,
-			      ARRAY_SIZE(n8x0_i2c_board_info_1));
-}
-
-#else
-static inline void __init n8x0_menelaus_init(void)
-{
-}
-#endif
+static struct i2c_board_info n810_i2c_board_info_2[] __initdata = {
+	{
+		I2C_BOARD_INFO("tlv320aic3x", 0x18),
+		.platform_data = &n810_aic33_data,
+	},
+};
 
 static void __init n8x0_map_io(void)
 {
@@ -653,6 +646,11 @@ static void __init n8x0_init_irq(void)
 
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
+	/* I2S codec port pins for McBSP block */
+	OMAP2420_MUX(EAC_AC_SCLK, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
+	OMAP2420_MUX(EAC_AC_FS, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
+	OMAP2420_MUX(EAC_AC_DIN, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
+	OMAP2420_MUX(EAC_AC_DOUT, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #else
@@ -665,9 +663,14 @@ static void __init n8x0_init_machine(void)
 	/* FIXME: add n810 spi devices */
 	spi_register_board_info(n800_spi_board_info,
 				ARRAY_SIZE(n800_spi_board_info));
+	omap_register_i2c_bus(1, 400, n8x0_i2c_board_info_1,
+			      ARRAY_SIZE(n8x0_i2c_board_info_1));
+	omap_register_i2c_bus(2, 400, NULL, 0);
+	if (machine_is_nokia_n810())
+		i2c_register_board_info(2, n810_i2c_board_info_2,
+					ARRAY_SIZE(n810_i2c_board_info_2));
 
 	omap_serial_init();
-	n8x0_menelaus_init();
 	n8x0_onenand_init();
 	n8x0_mmc_init();
 	n8x0_usb_init();

arch/arm/mach-omap2/board-omap3beagle.c

@@ -27,6 +27,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand.h>
+#include <linux/mmc/host.h>
 
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
@@ -43,13 +44,100 @@
 #include <plat/gpmc.h>
 #include <plat/nand.h>
 #include <plat/usb.h>
-#include <plat/timer-gp.h>
 
 #include "mux.h"
 #include "hsmmc.h"
+#include "timer-gp.h"
 
 #define NAND_BLOCK_SIZE		SZ_128K
 
+/*
+ * OMAP3 Beagle revision
+ * Run time detection of Beagle revision is done by reading GPIO.
+ * GPIO ID -
+ *	AXBX	= GPIO173, GPIO172, GPIO171: 1 1 1
+ *	C1_3	= GPIO173, GPIO172, GPIO171: 1 1 0
+ *	C4	= GPIO173, GPIO172, GPIO171: 1 0 1
+ *	XM	= GPIO173, GPIO172, GPIO171: 0 0 0
+ */
+enum {
+	OMAP3BEAGLE_BOARD_UNKN = 0,
+	OMAP3BEAGLE_BOARD_AXBX,
+	OMAP3BEAGLE_BOARD_C1_3,
+	OMAP3BEAGLE_BOARD_C4,
+	OMAP3BEAGLE_BOARD_XM,
+};
+
+static u8 omap3_beagle_version;
+
+static u8 omap3_beagle_get_rev(void)
+{
+	return omap3_beagle_version;
+}
+
+static void __init omap3_beagle_init_rev(void)
+{
+	int ret;
+	u16 beagle_rev = 0;
+
+	omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
+	omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
+	omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
+
+	ret = gpio_request(171, "rev_id_0");
+	if (ret < 0)
+		goto fail0;
+
+	ret = gpio_request(172, "rev_id_1");
+	if (ret < 0)
+		goto fail1;
+
+	ret = gpio_request(173, "rev_id_2");
+	if (ret < 0)
+		goto fail2;
+
+	gpio_direction_input(171);
+	gpio_direction_input(172);
+	gpio_direction_input(173);
+
+	beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
+			| (gpio_get_value(173) << 2);
+
+	switch (beagle_rev) {
+	case 7:
+		printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
+		omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
+		break;
+	case 6:
+		printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
+		omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
+		break;
+	case 5:
+		printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
+		omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
+		break;
+	case 0:
+		printk(KERN_INFO "OMAP3 Beagle Rev: xM\n");
+		omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
+		break;
+	default:
+		printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
+		omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
+	}
+
+	return;
+
+fail2:
+	gpio_free(172);
+fail1:
+	gpio_free(171);
+fail0:
+	printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
+	omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
+
+	return;
+}
+
 static struct mtd_partition omap3beagle_nand_partitions[] = {
 	/* All the partition sizes are listed in terms of NAND block size */
 	{
@@ -166,7 +254,7 @@ static void __init beagle_display_init(void)
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 29,
 	},
 	{}	/* Terminator */
@@ -185,7 +273,10 @@ static struct gpio_led gpio_leds[];
 static int beagle_twl_gpio_setup(struct device *dev,
 		unsigned gpio, unsigned ngpio)
 {
-	if (system_rev >= 0x20 && system_rev <= 0x34301000) {
+	if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
+		mmc[0].gpio_wp = -EINVAL;
+	} else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
+		(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) {
 		omap_mux_init_gpio(23, OMAP_PIN_INPUT);
 		mmc[0].gpio_wp = 23;
 	} else {
@@ -322,13 +413,19 @@ static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
 	},
 };
 
+static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
+       {
+               I2C_BOARD_INFO("eeprom", 0x50),
+       },
+};
+
 static int __init omap3_beagle_i2c_init(void)
 {
 	omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
 			ARRAY_SIZE(beagle_i2c_boardinfo));
 	/* Bus 3 is attached to the DVI port where devices like the pico DLP
 	 * projector don't work reliably with 400kHz */
-	omap_register_i2c_bus(3, 100, NULL, 0);
+	omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
 	return 0;
 }
 
@@ -464,6 +561,7 @@ static struct omap_musb_board_data musb_board_data = {
 static void __init omap3_beagle_init(void)
 {
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+	omap3_beagle_init_rev();
 	omap3_beagle_i2c_init();
 	platform_add_devices(omap3_beagle_devices,
 			ARRAY_SIZE(omap3_beagle_devices));

arch/arm/mach-omap2/board-omap3evm.c

@@ -31,6 +31,7 @@
 #include <linux/smsc911x.h>
 
 #include <linux/regulator/machine.h>
+#include <linux/mmc/host.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -370,7 +371,7 @@ static struct regulator_init_data omap3evm_vsim = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 63,
 	},
@@ -446,7 +447,7 @@ static struct twl4030_usb_data omap3evm_usb_data = {
 	.usb_mode	= T2_USB_MODE_ULPI,
 };
 
-static int board_keymap[] = {
+static uint32_t board_keymap[] = {
 	KEY(0, 0, KEY_LEFT),
 	KEY(0, 1, KEY_DOWN),
 	KEY(0, 2, KEY_ENTER),
@@ -584,7 +585,7 @@ static int ads7846_get_pendown_state(void)
 	return !gpio_get_value(OMAP3_EVM_TS_GPIO);
 }
 
-struct ads7846_platform_data ads7846_config = {
+static struct ads7846_platform_data ads7846_config = {
 	.x_max			= 0x0fff,
 	.y_max			= 0x0fff,
 	.x_plate_ohms		= 180,
@@ -603,7 +604,7 @@ static struct omap2_mcspi_device_config ads7846_mcspi_config = {
 	.single_channel	= 1,	/* 0: slave, 1: master */
 };
 
-struct spi_board_info omap3evm_spi_board_info[] = {
+static struct spi_board_info omap3evm_spi_board_info[] = {
 	[0] = {
 		.modalias		= "ads7846",
 		.bus_num		= 1,

arch/arm/mach-omap2/board-omap3logic.c

+/*
+ * linux/arch/arm/mach-omap2/board-omap3logic.c
+ *
+ * Copyright (C) 2010 Li-Pro.Net
+ * Stephan Linz <linz@li-pro.net>
+ *
+ * Copyright (C) 2010 Logic Product Development, Inc.
+ * Peter Barada <peter.barada@logicpd.com>
+ *
+ * Modified from Beagle, EVM, and RX51
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+
+#include <linux/regulator/machine.h>
+
+#include <linux/i2c/twl.h>
+#include <linux/mmc/host.h>
+
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include "mux.h"
+#include "hsmmc.h"
+#include "timer-gp.h"
+#include "control.h"
+
+#include <plat/mux.h>
+#include <plat/board.h>
+#include <plat/common.h>
+#include <plat/gpmc-smsc911x.h>
+#include <plat/gpmc.h>
+#include <plat/sdrc.h>
+
+#define OMAP3LOGIC_SMSC911X_CS			1
+
+#define OMAP3530_LV_SOM_MMC_GPIO_CD		110
+#define OMAP3530_LV_SOM_MMC_GPIO_WP		126
+#define OMAP3530_LV_SOM_SMSC911X_GPIO_IRQ	152
+
+#define OMAP3_TORPEDO_MMC_GPIO_CD		127
+#define OMAP3_TORPEDO_SMSC911X_GPIO_IRQ		129
+
+static struct regulator_consumer_supply omap3logic_vmmc1_supply = {
+	.supply			= "vmmc",
+};
+
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data omap3logic_vmmc1 = {
+	.constraints = {
+		.name			= "VMMC1",
+		.min_uV			= 1850000,
+		.max_uV			= 3150000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = &omap3logic_vmmc1_supply,
+};
+
+static struct twl4030_gpio_platform_data omap3logic_gpio_data = {
+	.gpio_base	= OMAP_MAX_GPIO_LINES,
+	.irq_base	= TWL4030_GPIO_IRQ_BASE,
+	.irq_end	= TWL4030_GPIO_IRQ_END,
+	.use_leds	= true,
+	.pullups	= BIT(1),
+	.pulldowns	= BIT(2)  | BIT(6)  | BIT(7)  | BIT(8)
+			| BIT(13) | BIT(15) | BIT(16) | BIT(17),
+};
+
+static struct twl4030_platform_data omap3logic_twldata = {
+	.irq_base	= TWL4030_IRQ_BASE,
+	.irq_end	= TWL4030_IRQ_END,
+
+	/* platform_data for children goes here */
+	.gpio		= &omap3logic_gpio_data,
+	.vmmc1		= &omap3logic_vmmc1,
+};
+
+static struct i2c_board_info __initdata omap3logic_i2c_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("twl4030", 0x48),
+		.flags = I2C_CLIENT_WAKE,
+		.irq = INT_34XX_SYS_NIRQ,
+		.platform_data = &omap3logic_twldata,
+	},
+};
+
+static int __init omap3logic_i2c_init(void)
+{
+	omap_register_i2c_bus(1, 2600, omap3logic_i2c_boardinfo,
+				ARRAY_SIZE(omap3logic_i2c_boardinfo));
+	return 0;
+}
+
+static struct omap2_hsmmc_info __initdata board_mmc_info[] = {
+	{
+		.name		= "external",
+		.mmc		= 1,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
+	},
+	{}      /* Terminator */
+};
+
+static void __init board_mmc_init(void)
+{
+	if (machine_is_omap3530_lv_som()) {
+		/* OMAP3530 LV SOM board */
+		board_mmc_info[0].gpio_cd = OMAP3530_LV_SOM_MMC_GPIO_CD;
+		board_mmc_info[0].gpio_wp = OMAP3530_LV_SOM_MMC_GPIO_WP;
+		omap_mux_init_signal("gpio_110", OMAP_PIN_OUTPUT);
+		omap_mux_init_signal("gpio_126", OMAP_PIN_OUTPUT);
+	} else if (machine_is_omap3_torpedo()) {
+		/* OMAP3 Torpedo board */
+		board_mmc_info[0].gpio_cd = OMAP3_TORPEDO_MMC_GPIO_CD;
+		omap_mux_init_signal("gpio_127", OMAP_PIN_OUTPUT);
+	} else {
+		/* unsupported board */
+		printk(KERN_ERR "%s(): unknown machine type\n", __func__);
+		return;
+	}
+
+	omap2_hsmmc_init(board_mmc_info);
+	/* link regulators to MMC adapters */
+	omap3logic_vmmc1_supply.dev = board_mmc_info[0].dev;
+}
+
+static struct omap_smsc911x_platform_data __initdata board_smsc911x_data = {
+	.cs             = OMAP3LOGIC_SMSC911X_CS,
+	.gpio_irq       = -EINVAL,
+	.gpio_reset     = -EINVAL,
+	.flags          = IORESOURCE_IRQ_LOWLEVEL,
+};
+
+/* TODO/FIXME (comment by Peter Barada, LogicPD):
+ * Fix the PBIAS voltage for Torpedo MMC1 pins that
+ * are used for other needs (IRQs, etc).            */
+static void omap3torpedo_fix_pbias_voltage(void)
+{
+	u16 control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE;
+	u32 reg;
+
+	if (machine_is_omap3_torpedo())
+	{
+		/* Set the bias for the pin */
+		reg = omap_ctrl_readl(control_pbias_offset);
+
+		reg &= ~OMAP343X_PBIASLITEPWRDNZ1;
+		omap_ctrl_writel(reg, control_pbias_offset);
+
+		/* 100ms delay required for PBIAS configuration */
+		msleep(100);
+
+		reg |= OMAP343X_PBIASLITEVMODE1;
+		reg |= OMAP343X_PBIASLITEPWRDNZ1;
+		omap_ctrl_writel(reg | 0x300, control_pbias_offset);
+	}
+}
+
+static inline void __init board_smsc911x_init(void)
+{
+	if (machine_is_omap3530_lv_som()) {
+		/* OMAP3530 LV SOM board */
+		board_smsc911x_data.gpio_irq =
+					OMAP3530_LV_SOM_SMSC911X_GPIO_IRQ;
+		omap_mux_init_signal("gpio_152", OMAP_PIN_INPUT);
+	} else if (machine_is_omap3_torpedo()) {
+		/* OMAP3 Torpedo board */
+		board_smsc911x_data.gpio_irq = OMAP3_TORPEDO_SMSC911X_GPIO_IRQ;
+		omap_mux_init_signal("gpio_129", OMAP_PIN_INPUT);
+	} else {
+		/* unsupported board */
+		printk(KERN_ERR "%s(): unknown machine type\n", __func__);
+		return;
+	}
+
+	gpmc_smsc911x_init(&board_smsc911x_data);
+}
+
+static void __init omap3logic_init_irq(void)
+{
+	omap2_init_common_hw(NULL, NULL);
+	omap_init_irq();
+	omap_gpio_init();
+}
+
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+#else
+#define board_mux       NULL
+#endif
+
+static void __init omap3logic_init(void)
+{
+	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+	omap3torpedo_fix_pbias_voltage();
+	omap3logic_i2c_init();
+	omap_serial_init();
+	board_mmc_init();
+	board_smsc911x_init();
+
+	/* Ensure SDRC pins are mux'd for self-refresh */
+	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
+}
+
+MACHINE_START(OMAP3_TORPEDO, "Logic OMAP3 Torpedo board")
+	.boot_params	= 0x80000100,
+	.map_io		= omap3_map_io,
+	.init_irq	= omap3logic_init_irq,
+	.init_machine	= omap3logic_init,
+	.timer		= &omap_timer,
+MACHINE_END
+
+MACHINE_START(OMAP3530_LV_SOM, "OMAP Logic 3530 LV SOM board")
+	.boot_params	= 0x80000100,
+	.map_io		= omap3_map_io,
+	.init_irq	= omap3logic_init_irq,
+	.init_machine	= omap3logic_init,
+	.timer		= &omap_timer,
+MACHINE_END

arch/arm/mach-omap2/board-omap3pandora.c

@@ -32,7 +32,9 @@
 #include <linux/input.h>
 #include <linux/input/matrix_keypad.h>
 #include <linux/gpio_keys.h>
+#include <linux/mmc/host.h>
 #include <linux/mmc/card.h>
+#include <linux/regulator/fixed.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -276,14 +278,14 @@ static void pandora_wl1251_init_card(struct mmc_card *card)
 static struct omap2_hsmmc_info omap3pandora_mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 126,
 		.ext_clock	= 0,
 	},
 	{
 		.mmc		= 2,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 127,
 		.ext_clock	= 1,
@@ -291,7 +293,7 @@ static struct omap2_hsmmc_info omap3pandora_mmc[] = {
 	},
 	{
 		.mmc		= 3,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.init_card	= pandora_wl1251_init_card,
@@ -344,6 +346,9 @@ static struct regulator_consumer_supply pandora_vmmc1_supply =
 static struct regulator_consumer_supply pandora_vmmc2_supply =
 	REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.1");
 
+static struct regulator_consumer_supply pandora_vmmc3_supply =
+	REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.2");
+
 static struct regulator_consumer_supply pandora_vdda_dac_supply =
 	REGULATOR_SUPPLY("vdda_dac", "omapdss");
 
@@ -488,6 +493,33 @@ static struct regulator_init_data pandora_vsim = {
 	.consumer_supplies	= &pandora_adac_supply,
 };
 
+/* Fixed regulator internal to Wifi module */
+static struct regulator_init_data pandora_vmmc3 = {
+	.constraints = {
+		.valid_ops_mask		= REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &pandora_vmmc3_supply,
+};
+
+static struct fixed_voltage_config pandora_vwlan = {
+	.supply_name		= "vwlan",
+	.microvolts		= 1800000, /* 1.8V */
+	.gpio			= PANDORA_WIFI_NRESET_GPIO,
+	.startup_delay		= 50000, /* 50ms */
+	.enable_high		= 1,
+	.enabled_at_boot	= 0,
+	.init_data		= &pandora_vmmc3,
+};
+
+static struct platform_device pandora_vwlan_device = {
+	.name		= "reg-fixed-voltage",
+	.id		= 1,
+	.dev = {
+		.platform_data = &pandora_vwlan,
+	},
+};
+
 static struct twl4030_usb_data omap3pandora_usb_data = {
 	.usb_mode	= T2_USB_MODE_ULPI,
 };
@@ -501,6 +533,8 @@ static struct twl4030_codec_data omap3pandora_codec_data = {
 	.audio = &omap3pandora_audio_data,
 };
 
+static struct twl4030_bci_platform_data pandora_bci_data;
+
 static struct twl4030_platform_data omap3pandora_twldata = {
 	.irq_base	= TWL4030_IRQ_BASE,
 	.irq_end	= TWL4030_IRQ_END,
@@ -516,6 +550,7 @@ static struct twl4030_platform_data omap3pandora_twldata = {
 	.vaux4		= &pandora_vaux4,
 	.vsim		= &pandora_vsim,
 	.keypad		= &pandora_kp_data,
+	.bci		= &pandora_bci_data,
 };
 
 static struct i2c_board_info __initdata omap3pandora_i2c_boardinfo[] = {
@@ -644,19 +679,8 @@ static void pandora_wl1251_init(void)
 	if (pandora_wl1251_pdata.irq < 0)
 		goto fail_irq;
 
-	ret = gpio_request(PANDORA_WIFI_NRESET_GPIO, "wl1251 nreset");
-	if (ret < 0)
-		goto fail_irq;
-
-	/* start powered so that it probes with MMC subsystem */
-	ret = gpio_direction_output(PANDORA_WIFI_NRESET_GPIO, 1);
-	if (ret < 0)
-		goto fail_nreset;
-
 	return;
 
-fail_nreset:
-	gpio_free(PANDORA_WIFI_NRESET_GPIO);
 fail_irq:
 	gpio_free(PANDORA_WIFI_IRQ_GPIO);
 fail:
@@ -668,6 +692,7 @@ static struct platform_device *omap3pandora_devices[] __initdata = {
 	&pandora_keys_gpio,
 	&pandora_dss_device,
 	&pandora_wl1251_data,
+	&pandora_vwlan_device,
 };
 
 static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {

arch/arm/mach-omap2/board-omap3stalker.c

@@ -26,6 +26,7 @@
 
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
+#include <linux/mmc/host.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -38,7 +39,6 @@
 #include <plat/gpmc.h>
 #include <plat/nand.h>
 #include <plat/usb.h>
-#include <plat/timer-gp.h>
 #include <plat/display.h>
 
 #include <plat/mcspi.h>
@@ -52,6 +52,7 @@
 #include "sdram-micron-mt46h32m32lf-6.h"
 #include "mux.h"
 #include "hsmmc.h"
+#include "timer-gp.h"
 
 #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
 #define OMAP3STALKER_ETHR_START	0x2c000000
@@ -275,7 +276,7 @@ static struct regulator_init_data omap3stalker_vsim = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 	 .mmc		= 1,
-	 .wires		= 4,
+	 .caps		= MMC_CAP_4_BIT_DATA,
 	 .gpio_cd	= -EINVAL,
 	 .gpio_wp	= 23,
 	 },
@@ -389,7 +390,7 @@ static struct twl4030_usb_data omap3stalker_usb_data = {
 	.usb_mode	= T2_USB_MODE_ULPI,
 };
 
-static int board_keymap[] = {
+static uint32_t board_keymap[] = {
 	KEY(0, 0, KEY_LEFT),
 	KEY(0, 1, KEY_DOWN),
 	KEY(0, 2, KEY_ENTER),
@@ -564,7 +565,7 @@ static struct omap2_mcspi_device_config ads7846_mcspi_config = {
 	.single_channel		= 1,	/* 0: slave, 1: master */
 };
 
-struct spi_board_info omap3stalker_spi_board_info[] = {
+static struct spi_board_info omap3stalker_spi_board_info[] = {
 	[0] = {
 	       .modalias	= "ads7846",
 	       .bus_num		= 1,

arch/arm/mach-omap2/board-omap3touchbook.c

@@ -27,6 +27,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand.h>
+#include <linux/mmc/host.h>
 
 #include <plat/mcspi.h>
 #include <linux/spi/spi.h>
@@ -47,10 +48,10 @@
 #include <plat/gpmc.h>
 #include <plat/nand.h>
 #include <plat/usb.h>
-#include <plat/timer-gp.h>
 
 #include "mux.h"
 #include "hsmmc.h"
+#include "timer-gp.h"
 
 #include <asm/setup.h>
 
@@ -61,7 +62,7 @@
 #define TB_BL_PWM_TIMER		9
 #define TB_KILL_POWER_GPIO	168
 
-unsigned long touchbook_revision;
+static unsigned long touchbook_revision;
 
 static struct mtd_partition omap3touchbook_nand_partitions[] = {
 	/* All the partition sizes are listed in terms of NAND block size */
@@ -108,7 +109,7 @@ static struct omap_nand_platform_data omap3touchbook_nand_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 29,
 	},
 	{}	/* Terminator */

arch/arm/mach-omap2/board-omap4panda.c

@@ -20,6 +20,7 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/leds.h>
 #include <linux/gpio.h>
 #include <linux/usb/otg.h>
 #include <linux/i2c/twl.h>
@@ -33,12 +34,45 @@
 
 #include <plat/board.h>
 #include <plat/common.h>
-#include <plat/control.h>
-#include <plat/timer-gp.h>
 #include <plat/usb.h>
 #include <plat/mmc.h>
+#include "timer-gp.h"
+
 #include "hsmmc.h"
+#include "control.h"
+
+#define GPIO_HUB_POWER		1
+#define GPIO_HUB_NRESET		62
+
+static struct gpio_led gpio_leds[] = {
+	{
+		.name			= "pandaboard::status1",
+		.default_trigger	= "heartbeat",
+		.gpio			= 7,
+	},
+	{
+		.name			= "pandaboard::status2",
+		.default_trigger	= "mmc0",
+		.gpio			= 8,
+	},
+};
 
+static struct gpio_led_platform_data gpio_led_info = {
+	.leds		= gpio_leds,
+	.num_leds	= ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &gpio_led_info,
+	},
+};
+
+static struct platform_device *panda_devices[] __initdata = {
+	&leds_gpio,
+};
 
 static void __init omap4_panda_init_irq(void)
 {
@@ -47,6 +81,56 @@ static void __init omap4_panda_init_irq(void)
 	omap_gpio_init();
 }
 
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+	.port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+	.phy_reset  = false,
+	.reset_gpio_port[0]  = -EINVAL,
+	.reset_gpio_port[1]  = -EINVAL,
+	.reset_gpio_port[2]  = -EINVAL
+};
+
+static void __init omap4_ehci_init(void)
+{
+	int ret;
+
+
+	/* disable the power to the usb hub prior to init */
+	ret = gpio_request(GPIO_HUB_POWER, "hub_power");
+	if (ret) {
+		pr_err("Cannot request GPIO %d\n", GPIO_HUB_POWER);
+		goto error1;
+	}
+	gpio_export(GPIO_HUB_POWER, 0);
+	gpio_direction_output(GPIO_HUB_POWER, 0);
+	gpio_set_value(GPIO_HUB_POWER, 0);
+
+	/* reset phy+hub */
+	ret = gpio_request(GPIO_HUB_NRESET, "hub_nreset");
+	if (ret) {
+		pr_err("Cannot request GPIO %d\n", GPIO_HUB_NRESET);
+		goto error2;
+	}
+	gpio_export(GPIO_HUB_NRESET, 0);
+	gpio_direction_output(GPIO_HUB_NRESET, 0);
+	gpio_set_value(GPIO_HUB_NRESET, 0);
+	gpio_set_value(GPIO_HUB_NRESET, 1);
+
+	usb_ehci_init(&ehci_pdata);
+
+	/* enable power to hub */
+	gpio_set_value(GPIO_HUB_POWER, 1);
+	return;
+
+error2:
+	gpio_free(GPIO_HUB_POWER);
+error1:
+	pr_err("Unable to initialize EHCI power/reset\n");
+	return;
+
+}
+
 static struct omap_musb_board_data musb_board_data = {
 	.interface_type		= MUSB_INTERFACE_UTMI,
 	.mode			= MUSB_PERIPHERAL,
@@ -56,7 +140,7 @@ static struct omap_musb_board_data musb_board_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= -EINVAL,
 	},
 	{}	/* Terminator */
@@ -67,10 +151,6 @@ static struct regulator_consumer_supply omap4_panda_vmmc_supply[] = {
 		.supply = "vmmc",
 		.dev_name = "mmci-omap-hs.0",
 	},
-	{
-		.supply = "vmmc",
-		.dev_name = "mmci-omap-hs.1",
-	},
 };
 
 static int omap4_twl6030_hsmmc_late_init(struct device *dev)
@@ -89,7 +169,14 @@ static int omap4_twl6030_hsmmc_late_init(struct device *dev)
 
 static __init void omap4_twl6030_hsmmc_set_late_init(struct device *dev)
 {
-	struct omap_mmc_platform_data *pdata = dev->platform_data;
+	struct omap_mmc_platform_data *pdata;
+
+	/* dev can be null if CONFIG_MMC_OMAP_HS is not set */
+	if (!dev) {
+		pr_err("Failed omap4_twl6030_hsmmc_set_late_init\n");
+		return;
+	}
+	pdata = dev->platform_data;
 
 	pdata->init =	omap4_twl6030_hsmmc_late_init;
 }
@@ -156,7 +243,7 @@ static struct regulator_init_data omap4_panda_vmmc = {
 					| REGULATOR_CHANGE_MODE
 					| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies  = 2,
+	.num_consumer_supplies  = 1,
 	.consumer_supplies      = omap4_panda_vmmc_supply,
 };
 
@@ -274,13 +361,13 @@ static int __init omap4_panda_i2c_init(void)
 }
 static void __init omap4_panda_init(void)
 {
-	int status;
-
 	omap4_panda_i2c_init();
+	platform_add_devices(panda_devices, ARRAY_SIZE(panda_devices));
 	omap_serial_init();
 	omap4_twl6030_hsmmc_init(mmc);
 	/* OMAP4 Panda uses internal transceiver so register nop transceiver */
 	usb_nop_xceiv_register();
+	omap4_ehci_init();
 	/* FIXME: allow multi-omap to boot until musb is updated for omap4 */
 	if (!cpu_is_omap44xx())
 		usb_musb_init(&musb_board_data);

arch/arm/mach-omap2/board-overo.c

@@ -32,6 +32,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
+#include <linux/mmc/host.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -303,13 +304,13 @@ static void __init overo_flash_init(void)
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 	},
 	{
 		.mmc		= 2,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.transceiver	= true,

arch/arm/mach-omap2/board-rx51-peripherals.c

@@ -33,6 +33,8 @@
 #include <plat/onenand.h>
 #include <plat/gpmc-smc91x.h>
 
+#include <mach/board-rx51.h>
+
 #include <sound/tlv320aic3x.h>
 #include <sound/tpa6130a2-plat.h>
 
@@ -185,7 +187,7 @@ static void __init rx51_add_gpio_keys(void)
 }
 #endif /* CONFIG_KEYBOARD_GPIO || CONFIG_KEYBOARD_GPIO_MODULE */
 
-static int board_keymap[] = {
+static uint32_t board_keymap[] = {
 	/*
 	 * Note that KEY(x, 8, KEY_XXX) entries represent "entrire row
 	 * connected to the ground" matrix state.
@@ -303,7 +305,7 @@ static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.name		= "external",
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.cover_only	= true,
 		.gpio_cd	= 160,
 		.gpio_wp	= -EINVAL,
@@ -312,7 +314,8 @@ static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.name		= "internal",
 		.mmc		= 2,
-		.wires		= 8, /* See also rx51_mmc2_remux */
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
+						/* See also rx51_mmc2_remux */
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.nonremovable	= true,

arch/arm/mach-omap2/board-rx51-sdram.c

@@ -43,7 +43,7 @@ struct sdram_timings {
 	u32 tWTR;
 };
 
-struct omap_sdrc_params rx51_sdrc_params[4];
+static struct omap_sdrc_params rx51_sdrc_params[4];
 
 static const struct sdram_timings rx51_timings[] = {
 	{

arch/arm/mach-omap2/board-rx51-video.c

@@ -20,6 +20,8 @@
 #include <plat/vram.h>
 #include <plat/mcspi.h>
 
+#include <mach/board-rx51.h>
+
 #include "mux.h"
 
 #define RX51_LCD_RESET_GPIO	90

arch/arm/mach-omap2/board-zoom-debugboard.c

@@ -16,6 +16,8 @@
 
 #include <plat/gpmc.h>
 
+#include <mach/board-zoom.h>
+
 #define ZOOM_SMSC911X_CS	7
 #define ZOOM_SMSC911X_GPIO	158
 #define ZOOM_QUADUART_CS	3

arch/arm/mach-omap2/board-zoom-peripherals.c

@@ -18,6 +18,7 @@
 #include <linux/regulator/machine.h>
 #include <linux/regulator/fixed.h>
 #include <linux/wl12xx.h>
+#include <linux/mmc/host.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -35,7 +36,7 @@
 #define OMAP_ZOOM_WLAN_IRQ_GPIO		(162)
 
 /* Zoom2 has Qwerty keyboard*/
-static int board_keymap[] = {
+static uint32_t board_keymap[] = {
 	KEY(0, 0, KEY_E),
 	KEY(0, 1, KEY_R),
 	KEY(0, 2, KEY_T),
@@ -199,14 +200,14 @@ static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.name		= "external",
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_wp	= -EINVAL,
 		.power_saving	= true,
 	},
 	{
 		.name		= "internal",
 		.mmc		= 2,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.nonremovable	= true,
@@ -348,4 +349,5 @@ void __init zoom_peripherals_init(void)
 	platform_device_register(&omap_vwlan_device);
 	usb_musb_init(&musb_board_data);
 	enable_board_wakeup_source();
+	omap_serial_init();
 }

arch/arm/mach-omap2/board-zoom2.c

@@ -24,6 +24,7 @@
 
 #include <mach/board-zoom.h>
 
+#include "board-flash.h"
 #include "mux.h"
 #include "sdram-micron-mt46h32m32lf-6.h"
 

arch/arm/mach-omap2/board-zoom3.c

@@ -22,6 +22,7 @@
 #include <plat/board.h>
 #include <plat/usb.h>
 
+#include "board-flash.h"
 #include "mux.h"
 #include "sdram-hynix-h8mbx00u0mer-0em.h"
 

arch/arm/mach-omap2/clock.c

@@ -395,7 +395,7 @@ void omap2_clk_disable_unused(struct clk *clk)
 	if ((regval32 & (1 << clk->enable_bit)) == v)
 		return;
 
-	printk(KERN_DEBUG "Disabling unused clock \"%s\"\n", clk->name);
+	pr_debug("Disabling unused clock \"%s\"\n", clk->name);
 	if (cpu_is_omap34xx()) {
 		omap2_clk_enable(clk);
 		omap2_clk_disable(clk);

arch/arm/mach-omap2/clock2420_data.c

@@ -27,6 +27,7 @@
 #include "prm-regbits-24xx.h"
 #include "cm-regbits-24xx.h"
 #include "sdrc.h"
+#include "control.h"
 
 #define OMAP_CM_REGADDR                 OMAP2420_CM_REGADDR
 
@@ -89,6 +90,12 @@ static struct clk alt_ck = {		/* Typical 54M or 48M, may not exist */
 	.clkdm_name	= "wkup_clkdm",
 };
 
+/* Optional external clock input for McBSP CLKS */
+static struct clk mcbsp_clks = {
+	.name		= "mcbsp_clks",
+	.ops		= &clkops_null,
+};
+
 /*
  * Analog domain root source clocks
  */
@@ -1135,14 +1142,34 @@ static struct clk mcbsp1_ick = {
 	.recalc		= &followparent_recalc,
 };
 
+static const struct clksel_rate common_mcbsp_96m_rates[] = {
+	{ .div = 1, .val = 0, .flags = RATE_IN_24XX },
+	{ .div = 0 }
+};
+
+static const struct clksel_rate common_mcbsp_mcbsp_rates[] = {
+	{ .div = 1, .val = 1, .flags = RATE_IN_24XX },
+	{ .div = 0 }
+};
+
+static const struct clksel mcbsp_fck_clksel[] = {
+	{ .parent = &func_96m_ck,  .rates = common_mcbsp_96m_rates },
+	{ .parent = &mcbsp_clks,   .rates = common_mcbsp_mcbsp_rates },
+	{ .parent = NULL }
+};
+
 static struct clk mcbsp1_fck = {
 	.name		= "mcbsp1_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &func_96m_ck,
+	.init		= &omap2_init_clksel_parent,
 	.clkdm_name	= "core_l4_clkdm",
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
 	.enable_bit	= OMAP24XX_EN_MCBSP1_SHIFT,
-	.recalc		= &followparent_recalc,
+	.clksel_reg	= OMAP242X_CTRL_REGADDR(OMAP2_CONTROL_DEVCONF0),
+	.clksel_mask	= OMAP2_MCBSP1_CLKS_MASK,
+	.clksel		= mcbsp_fck_clksel,
+	.recalc		= &omap2_clksel_recalc,
 };
 
 static struct clk mcbsp2_ick = {
@@ -1159,10 +1186,14 @@ static struct clk mcbsp2_fck = {
 	.name		= "mcbsp2_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &func_96m_ck,
+	.init		= &omap2_init_clksel_parent,
 	.clkdm_name	= "core_l4_clkdm",
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
 	.enable_bit	= OMAP24XX_EN_MCBSP2_SHIFT,
-	.recalc		= &followparent_recalc,
+	.clksel_reg	= OMAP242X_CTRL_REGADDR(OMAP2_CONTROL_DEVCONF0),
+	.clksel_mask	= OMAP2_MCBSP2_CLKS_MASK,
+	.clksel		= mcbsp_fck_clksel,
+	.recalc		= &omap2_clksel_recalc,
 };
 
 static struct clk mcspi1_ick = {
@@ -1721,6 +1752,9 @@ static struct omap_clk omap2420_clks[] = {
 	CLK(NULL,	"osc_ck",	&osc_ck,	CK_242X),
 	CLK(NULL,	"sys_ck",	&sys_ck,	CK_242X),
 	CLK(NULL,	"alt_ck",	&alt_ck,	CK_242X),
+	CLK("omap-mcbsp.1",	"pad_fck",	&mcbsp_clks,	CK_242X),
+	CLK("omap-mcbsp.2",	"pad_fck",	&mcbsp_clks,	CK_242X),
+	CLK(NULL,	"mcbsp_clks",	&mcbsp_clks,	CK_242X),
 	/* internal analog sources */
 	CLK(NULL,	"dpll_ck",	&dpll_ck,	CK_242X),
 	CLK(NULL,	"apll96_ck",	&apll96_ck,	CK_242X),
@@ -1728,6 +1762,8 @@ static struct omap_clk omap2420_clks[] = {
 	/* internal prcm root sources */
 	CLK(NULL,	"func_54m_ck",	&func_54m_ck,	CK_242X),
 	CLK(NULL,	"core_ck",	&core_ck,	CK_242X),
+	CLK("omap-mcbsp.1",	"prcm_fck",	&func_96m_ck,	CK_242X),
+	CLK("omap-mcbsp.2",	"prcm_fck",	&func_96m_ck,	CK_242X),
 	CLK(NULL,	"func_96m_ck",	&func_96m_ck,	CK_242X),
 	CLK(NULL,	"func_48m_ck",	&func_48m_ck,	CK_242X),
 	CLK(NULL,	"func_12m_ck",	&func_12m_ck,	CK_242X),

arch/arm/mach-omap2/clock2430_data.c

@@ -27,6 +27,7 @@
 #include "prm-regbits-24xx.h"
 #include "cm-regbits-24xx.h"
 #include "sdrc.h"
+#include "control.h"
 
 #define OMAP_CM_REGADDR			OMAP2430_CM_REGADDR
 
@@ -89,6 +90,12 @@ static struct clk alt_ck = {		/* Typical 54M or 48M, may not exist */
 	.clkdm_name	= "wkup_clkdm",
 };
 
+/* Optional external clock input for McBSP CLKS */
+static struct clk mcbsp_clks = {
+	.name		= "mcbsp_clks",
+	.ops		= &clkops_null,
+};
+
 /*
  * Analog domain root source clocks
  */
@@ -1123,14 +1130,34 @@ static struct clk mcbsp1_ick = {
 	.recalc		= &followparent_recalc,
 };
 
+static const struct clksel_rate common_mcbsp_96m_rates[] = {
+	{ .div = 1, .val = 0, .flags = RATE_IN_24XX },
+	{ .div = 0 }
+};
+
+static const struct clksel_rate common_mcbsp_mcbsp_rates[] = {
+	{ .div = 1, .val = 1, .flags = RATE_IN_24XX },
+	{ .div = 0 }
+};
+
+static const struct clksel mcbsp_fck_clksel[] = {
+	{ .parent = &func_96m_ck,  .rates = common_mcbsp_96m_rates },
+	{ .parent = &mcbsp_clks,   .rates = common_mcbsp_mcbsp_rates },
+	{ .parent = NULL }
+};
+
 static struct clk mcbsp1_fck = {
 	.name		= "mcbsp1_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &func_96m_ck,
+	.init		= &omap2_init_clksel_parent,
 	.clkdm_name	= "core_l4_clkdm",
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
 	.enable_bit	= OMAP24XX_EN_MCBSP1_SHIFT,
-	.recalc		= &followparent_recalc,
+	.clksel_reg	= OMAP243X_CTRL_REGADDR(OMAP2_CONTROL_DEVCONF0),
+	.clksel_mask	= OMAP2_MCBSP1_CLKS_MASK,
+	.clksel		= mcbsp_fck_clksel,
+	.recalc		= &omap2_clksel_recalc,
 };
 
 static struct clk mcbsp2_ick = {
@@ -1147,10 +1174,14 @@ static struct clk mcbsp2_fck = {
 	.name		= "mcbsp2_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &func_96m_ck,
+	.init		= &omap2_init_clksel_parent,
 	.clkdm_name	= "core_l4_clkdm",
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
 	.enable_bit	= OMAP24XX_EN_MCBSP2_SHIFT,
-	.recalc		= &followparent_recalc,
+	.clksel_reg	= OMAP243X_CTRL_REGADDR(OMAP2_CONTROL_DEVCONF0),
+	.clksel_mask	= OMAP2_MCBSP2_CLKS_MASK,
+	.clksel		= mcbsp_fck_clksel,
+	.recalc		= &omap2_clksel_recalc,
 };
 
 static struct clk mcbsp3_ick = {
@@ -1167,10 +1198,14 @@ static struct clk mcbsp3_fck = {
 	.name		= "mcbsp3_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &func_96m_ck,
+	.init		= &omap2_init_clksel_parent,
 	.clkdm_name	= "core_l4_clkdm",
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2),
 	.enable_bit	= OMAP2430_EN_MCBSP3_SHIFT,
-	.recalc		= &followparent_recalc,
+	.clksel_reg	= OMAP243X_CTRL_REGADDR(OMAP243X_CONTROL_DEVCONF1),
+	.clksel_mask	= OMAP2_MCBSP3_CLKS_MASK,
+	.clksel		= mcbsp_fck_clksel,
+	.recalc		= &omap2_clksel_recalc,
 };
 
 static struct clk mcbsp4_ick = {
@@ -1187,10 +1222,14 @@ static struct clk mcbsp4_fck = {
 	.name		= "mcbsp4_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &func_96m_ck,
+	.init		= &omap2_init_clksel_parent,
 	.clkdm_name	= "core_l4_clkdm",
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2),
 	.enable_bit	= OMAP2430_EN_MCBSP4_SHIFT,
-	.recalc		= &followparent_recalc,
+	.clksel_reg	= OMAP243X_CTRL_REGADDR(OMAP243X_CONTROL_DEVCONF1),
+	.clksel_mask	= OMAP2_MCBSP4_CLKS_MASK,
+	.clksel		= mcbsp_fck_clksel,
+	.recalc		= &omap2_clksel_recalc,
 };
 
 static struct clk mcbsp5_ick = {
@@ -1207,10 +1246,14 @@ static struct clk mcbsp5_fck = {
 	.name		= "mcbsp5_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &func_96m_ck,
+	.init		= &omap2_init_clksel_parent,
 	.clkdm_name	= "core_l4_clkdm",
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2),
 	.enable_bit	= OMAP2430_EN_MCBSP5_SHIFT,
-	.recalc		= &followparent_recalc,
+	.clksel_reg	= OMAP243X_CTRL_REGADDR(OMAP243X_CONTROL_DEVCONF1),
+	.clksel_mask	= OMAP2_MCBSP5_CLKS_MASK,
+	.clksel		= mcbsp_fck_clksel,
+	.recalc		= &omap2_clksel_recalc,
 };
 
 static struct clk mcspi1_ick = {
@@ -1808,6 +1851,12 @@ static struct omap_clk omap2430_clks[] = {
 	CLK(NULL,	"osc_ck",	&osc_ck,	CK_243X),
 	CLK(NULL,	"sys_ck",	&sys_ck,	CK_243X),
 	CLK(NULL,	"alt_ck",	&alt_ck,	CK_243X),
+	CLK("omap-mcbsp.1",	"pad_fck",	&mcbsp_clks,	CK_243X),
+	CLK("omap-mcbsp.2",	"pad_fck",	&mcbsp_clks,	CK_243X),
+	CLK("omap-mcbsp.3",	"pad_fck",	&mcbsp_clks,	CK_243X),
+	CLK("omap-mcbsp.4",	"pad_fck",	&mcbsp_clks,	CK_243X),
+	CLK("omap-mcbsp.5",	"pad_fck",	&mcbsp_clks,	CK_243X),
+	CLK(NULL,	"mcbsp_clks",	&mcbsp_clks,	CK_243X),
 	/* internal analog sources */
 	CLK(NULL,	"dpll_ck",	&dpll_ck,	CK_243X),
 	CLK(NULL,	"apll96_ck",	&apll96_ck,	CK_243X),
@@ -1815,6 +1864,11 @@ static struct omap_clk omap2430_clks[] = {
 	/* internal prcm root sources */
 	CLK(NULL,	"func_54m_ck",	&func_54m_ck,	CK_243X),
 	CLK(NULL,	"core_ck",	&core_ck,	CK_243X),
+	CLK("omap-mcbsp.1",	"prcm_fck",	&func_96m_ck,	CK_243X),
+	CLK("omap-mcbsp.2",	"prcm_fck",	&func_96m_ck,	CK_243X),
+	CLK("omap-mcbsp.3",	"prcm_fck",	&func_96m_ck,	CK_243X),
+	CLK("omap-mcbsp.4",	"prcm_fck",	&func_96m_ck,	CK_243X),
+	CLK("omap-mcbsp.5",	"prcm_fck",	&func_96m_ck,	CK_243X),
 	CLK(NULL,	"func_96m_ck",	&func_96m_ck,	CK_243X),
 	CLK(NULL,	"func_48m_ck",	&func_48m_ck,	CK_243X),
 	CLK(NULL,	"func_12m_ck",	&func_12m_ck,	CK_243X),

arch/arm/mach-omap2/clock3xxx_data.c

@@ -20,7 +20,6 @@
 #include <linux/clk.h>
 #include <linux/list.h>
 
-#include <plat/control.h>
 #include <plat/clkdev_omap.h>
 
 #include "clock.h"
@@ -33,6 +32,7 @@
 #include "cm-regbits-34xx.h"
 #include "prm.h"
 #include "prm-regbits-34xx.h"
+#include "control.h"
 
 /*
  * clocks
@@ -2465,6 +2465,16 @@ static struct clk uart3_fck = {
 	.recalc		= &followparent_recalc,
 };
 
+static struct clk uart4_fck = {
+	.name		= "uart4_fck",
+	.ops		= &clkops_omap2_dflt_wait,
+	.parent		= &per_48m_fck,
+	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_PER_MOD, CM_FCLKEN),
+	.enable_bit	= OMAP3630_EN_UART4_SHIFT,
+	.clkdm_name	= "per_clkdm",
+	.recalc		= &followparent_recalc,
+};
+
 static struct clk gpt2_fck = {
 	.name		= "gpt2_fck",
 	.ops		= &clkops_omap2_dflt_wait,
@@ -2715,6 +2725,16 @@ static struct clk uart3_ick = {
 	.recalc		= &followparent_recalc,
 };
 
+static struct clk uart4_ick = {
+	.name		= "uart4_ick",
+	.ops		= &clkops_omap2_dflt_wait,
+	.parent		= &per_l4_ick,
+	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_PER_MOD, CM_ICLKEN),
+	.enable_bit	= OMAP3630_EN_UART4_SHIFT,
+	.clkdm_name	= "per_clkdm",
+	.recalc		= &followparent_recalc,
+};
+
 static struct clk gpt9_ick = {
 	.name		= "gpt9_ick",
 	.ops		= &clkops_omap2_dflt_wait,
@@ -3188,6 +3208,11 @@ static struct omap_clk omap3xxx_clks[] = {
 	CLK(NULL,	"osc_sys_ck",	&osc_sys_ck,	CK_3XXX),
 	CLK(NULL,	"sys_ck",	&sys_ck,	CK_3XXX),
 	CLK(NULL,	"sys_altclk",	&sys_altclk,	CK_3XXX),
+	CLK("omap-mcbsp.1",	"pad_fck",	&mcbsp_clks,	CK_3XXX),
+	CLK("omap-mcbsp.2",	"pad_fck",	&mcbsp_clks,	CK_3XXX),
+	CLK("omap-mcbsp.3",	"pad_fck",	&mcbsp_clks,	CK_3XXX),
+	CLK("omap-mcbsp.4",	"pad_fck",	&mcbsp_clks,	CK_3XXX),
+	CLK("omap-mcbsp.5",	"pad_fck",	&mcbsp_clks,	CK_3XXX),
 	CLK(NULL,	"mcbsp_clks",	&mcbsp_clks,	CK_3XXX),
 	CLK(NULL,	"sys_clkout1",	&sys_clkout1,	CK_3XXX),
 	CLK(NULL,	"dpll1_ck",	&dpll1_ck,	CK_3XXX),
@@ -3253,6 +3278,8 @@ static struct omap_clk omap3xxx_clks[] = {
 	CLK(NULL,	"cpefuse_fck",	&cpefuse_fck,	CK_3430ES2 | CK_AM35XX),
 	CLK(NULL,	"ts_fck",	&ts_fck,	CK_3430ES2 | CK_AM35XX),
 	CLK(NULL,	"usbtll_fck",	&usbtll_fck,	CK_3430ES2 | CK_AM35XX),
+	CLK("omap-mcbsp.1",	"prcm_fck",	&core_96m_fck,	CK_3XXX),
+	CLK("omap-mcbsp.5",	"prcm_fck",	&core_96m_fck,	CK_3XXX),
 	CLK(NULL,	"core_96m_fck",	&core_96m_fck,	CK_3XXX),
 	CLK("mmci-omap-hs.2",	"fck",	&mmchs3_fck,	CK_3430ES2 | CK_AM35XX),
 	CLK("mmci-omap-hs.1",	"fck",	&mmchs2_fck,	CK_3XXX),
@@ -3346,9 +3373,13 @@ static struct omap_clk omap3xxx_clks[] = {
 	CLK(NULL,	"omap_32ksync_ick", &omap_32ksync_ick, CK_3XXX),
 	CLK(NULL,	"gpt12_ick",	&gpt12_ick,	CK_3XXX),
 	CLK(NULL,	"gpt1_ick",	&gpt1_ick,	CK_3XXX),
+	CLK("omap-mcbsp.2",	"prcm_fck",	&per_96m_fck,	CK_3XXX),
+	CLK("omap-mcbsp.3",	"prcm_fck",	&per_96m_fck,	CK_3XXX),
+	CLK("omap-mcbsp.4",	"prcm_fck",	&per_96m_fck,	CK_3XXX),
 	CLK(NULL,	"per_96m_fck",	&per_96m_fck,	CK_3XXX),
 	CLK(NULL,	"per_48m_fck",	&per_48m_fck,	CK_3XXX),
 	CLK(NULL,	"uart3_fck",	&uart3_fck,	CK_3XXX),
+	CLK(NULL,	"uart4_fck",	&uart4_fck,	CK_36XX),
 	CLK(NULL,	"gpt2_fck",	&gpt2_fck,	CK_3XXX),
 	CLK(NULL,	"gpt3_fck",	&gpt3_fck,	CK_3XXX),
 	CLK(NULL,	"gpt4_fck",	&gpt4_fck,	CK_3XXX),
@@ -3372,6 +3403,7 @@ static struct omap_clk omap3xxx_clks[] = {
 	CLK(NULL,	"gpio2_ick",	&gpio2_ick,	CK_3XXX),
 	CLK(NULL,	"wdt3_ick",	&wdt3_ick,	CK_3XXX),
 	CLK(NULL,	"uart3_ick",	&uart3_ick,	CK_3XXX),
+	CLK(NULL,	"uart4_ick",	&uart4_ick,	CK_36XX),
 	CLK(NULL,	"gpt9_ick",	&gpt9_ick,	CK_3XXX),
 	CLK(NULL,	"gpt8_ick",	&gpt8_ick,	CK_3XXX),
 	CLK(NULL,	"gpt7_ick",	&gpt7_ick,	CK_3XXX),

arch/arm/mach-omap2/clockdomain.c

@@ -258,97 +258,6 @@ static void _omap2_clkdm_set_hwsup(struct clockdomain *clkdm, int enable)
 
 }
 
-/**
- * _init_wkdep_usecount - initialize wkdep usecounts to match hardware
- * @clkdm: clockdomain to initialize wkdep usecounts
- *
- * Initialize the wakeup dependency usecount variables for clockdomain @clkdm.
- * If a wakeup dependency is present in the hardware, the usecount will be
- * set to 1; otherwise, it will be set to 0.  Software should clear all
- * software wakeup dependencies prior to calling this function if it wishes
- * to ensure that all usecounts start at 0.  No return value.
- */
-static void _init_wkdep_usecount(struct clockdomain *clkdm)
-{
-	u32 v;
-	struct clkdm_dep *cd;
-
-	if (!clkdm->wkdep_srcs)
-		return;
-
-	for (cd = clkdm->wkdep_srcs; cd->clkdm_name; cd++) {
-		if (!omap_chip_is(cd->omap_chip))
-			continue;
-
-		if (!cd->clkdm && cd->clkdm_name)
-			cd->clkdm = _clkdm_lookup(cd->clkdm_name);
-
-		if (!cd->clkdm) {
-			WARN(!cd->clkdm, "clockdomain: %s: wkdep clkdm %s not "
-			     "found\n", clkdm->name, cd->clkdm_name);
-			continue;
-		}
-
-		v = prm_read_mod_bits_shift(clkdm->pwrdm.ptr->prcm_offs,
-					    PM_WKDEP,
-					    (1 << cd->clkdm->dep_bit));
-
-		if (v)
-			pr_debug("clockdomain: %s: wakeup dependency already "
-				 "set to wake up when %s wakes\n",
-				 clkdm->name, cd->clkdm->name);
-
-		atomic_set(&cd->wkdep_usecount, (v) ? 1 : 0);
-	}
-}
-
-/**
- * _init_sleepdep_usecount - initialize sleepdep usecounts to match hardware
- * @clkdm: clockdomain to initialize sleepdep usecounts
- *
- * Initialize the sleep dependency usecount variables for clockdomain @clkdm.
- * If a sleep dependency is present in the hardware, the usecount will be
- * set to 1; otherwise, it will be set to 0.  Software should clear all
- * software sleep dependencies prior to calling this function if it wishes
- * to ensure that all usecounts start at 0.  No return value.
- */
-static void _init_sleepdep_usecount(struct clockdomain *clkdm)
-{
-	u32 v;
-	struct clkdm_dep *cd;
-
-	if (!cpu_is_omap34xx())
-		return;
-
-	if (!clkdm->sleepdep_srcs)
-		return;
-
-	for (cd = clkdm->sleepdep_srcs; cd->clkdm_name; cd++) {
-		if (!omap_chip_is(cd->omap_chip))
-			continue;
-
-		if (!cd->clkdm && cd->clkdm_name)
-			cd->clkdm = _clkdm_lookup(cd->clkdm_name);
-
-		if (!cd->clkdm) {
-			WARN(!cd->clkdm, "clockdomain: %s: sleepdep clkdm %s "
-			     "not found\n", clkdm->name, cd->clkdm_name);
-			continue;
-		}
-
-		v = prm_read_mod_bits_shift(clkdm->pwrdm.ptr->prcm_offs,
-					    OMAP3430_CM_SLEEPDEP,
-					    (1 << cd->clkdm->dep_bit));
-
-		if (v)
-			pr_debug("clockdomain: %s: sleep dependency already "
-				 "set to prevent from idling until %s "
-				 "idles\n", clkdm->name, cd->clkdm->name);
-
-		atomic_set(&cd->sleepdep_usecount, (v) ? 1 : 0);
-	}
-};
-
 /* Public functions */
 
 /**
@@ -379,12 +288,17 @@ void clkdm_init(struct clockdomain **clkdms,
 			_autodep_lookup(autodep);
 
 	/*
-	 * Ensure that the *dep_usecount registers reflect the current
-	 * state of the PRCM.
+	 * Put all clockdomains into software-supervised mode; PM code
+	 * should later enable hardware-supervised mode as appropriate
 	 */
 	list_for_each_entry(clkdm, &clkdm_list, node) {
-		_init_wkdep_usecount(clkdm);
-		_init_sleepdep_usecount(clkdm);
+		if (clkdm->flags & CLKDM_CAN_FORCE_WAKEUP)
+			omap2_clkdm_wakeup(clkdm);
+		else if (clkdm->flags & CLKDM_CAN_DISABLE_AUTO)
+			omap2_clkdm_deny_idle(clkdm);
+
+		clkdm_clear_all_wkdeps(clkdm);
+		clkdm_clear_all_sleepdeps(clkdm);
 	}
 }
 
@@ -592,6 +506,9 @@ int clkdm_clear_all_wkdeps(struct clockdomain *clkdm)
 		if (!omap_chip_is(cd->omap_chip))
 			continue;
 
+		if (!cd->clkdm && cd->clkdm_name)
+			cd->clkdm = _clkdm_lookup(cd->clkdm_name);
+
 		/* PRM accesses are slow, so minimize them */
 		mask |= 1 << cd->clkdm->dep_bit;
 		atomic_set(&cd->wkdep_usecount, 0);
@@ -752,6 +669,9 @@ int clkdm_clear_all_sleepdeps(struct clockdomain *clkdm)
 		if (!omap_chip_is(cd->omap_chip))
 			continue;
 
+		if (!cd->clkdm && cd->clkdm_name)
+			cd->clkdm = _clkdm_lookup(cd->clkdm_name);
+
 		/* PRM accesses are slow, so minimize them */
 		mask |= 1 << cd->clkdm->dep_bit;
 		atomic_set(&cd->sleepdep_usecount, 0);

arch/arm/mach-omap2/cm-regbits-34xx.h

@@ -649,6 +649,8 @@
 #define OMAP3430_ST_MCBSP2_MASK				(1 << 0)
 
 /* CM_AUTOIDLE_PER */
+#define OMAP3630_AUTO_UART4_MASK			(1 << 18)
+#define OMAP3630_AUTO_UART4_SHIFT			18
 #define OMAP3430_AUTO_GPIO6_MASK			(1 << 17)
 #define OMAP3430_AUTO_GPIO6_SHIFT			17
 #define OMAP3430_AUTO_GPIO5_MASK			(1 << 16)

arch/arm/mach-omap2/cm44xx.h

@@ -195,6 +195,42 @@
 #define OMAP4_CM1_ABE_WDT3_CLKCTRL_OFFSET		0x0088
 #define OMAP4430_CM1_ABE_WDT3_CLKCTRL			OMAP44XX_CM1_REGADDR(OMAP4430_CM1_ABE_MOD, 0x0088)
 
+/* CM1.RESTORE_CM1 register offsets */
+#define OMAP4_CM_CLKSEL_CORE_RESTORE_OFFSET		0x0000
+#define OMAP4430_CM_CLKSEL_CORE_RESTORE			OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0000)
+#define OMAP4_CM_DIV_M2_DPLL_CORE_RESTORE_OFFSET	0x0004
+#define OMAP4430_CM_DIV_M2_DPLL_CORE_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0004)
+#define OMAP4_CM_DIV_M3_DPLL_CORE_RESTORE_OFFSET	0x0008
+#define OMAP4430_CM_DIV_M3_DPLL_CORE_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0008)
+#define OMAP4_CM_DIV_M4_DPLL_CORE_RESTORE_OFFSET	0x000c
+#define OMAP4430_CM_DIV_M4_DPLL_CORE_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x000c)
+#define OMAP4_CM_DIV_M5_DPLL_CORE_RESTORE_OFFSET	0x0010
+#define OMAP4430_CM_DIV_M5_DPLL_CORE_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0010)
+#define OMAP4_CM_DIV_M6_DPLL_CORE_RESTORE_OFFSET	0x0014
+#define OMAP4430_CM_DIV_M6_DPLL_CORE_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0014)
+#define OMAP4_CM_DIV_M7_DPLL_CORE_RESTORE_OFFSET	0x0018
+#define OMAP4430_CM_DIV_M7_DPLL_CORE_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0018)
+#define OMAP4_CM_CLKSEL_DPLL_CORE_RESTORE_OFFSET	0x001c
+#define OMAP4430_CM_CLKSEL_DPLL_CORE_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x001c)
+#define OMAP4_CM_SSC_DELTAMSTEP_DPLL_CORE_RESTORE_OFFSET	0x0020
+#define OMAP4430_CM_SSC_DELTAMSTEP_DPLL_CORE_RESTORE	OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0020)
+#define OMAP4_CM_SSC_MODFREQDIV_DPLL_CORE_RESTORE_OFFSET	0x0024
+#define OMAP4430_CM_SSC_MODFREQDIV_DPLL_CORE_RESTORE	OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0024)
+#define OMAP4_CM_CLKMODE_DPLL_CORE_RESTORE_OFFSET	0x0028
+#define OMAP4430_CM_CLKMODE_DPLL_CORE_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0028)
+#define OMAP4_CM_SHADOW_FREQ_CONFIG2_RESTORE_OFFSET	0x002c
+#define OMAP4430_CM_SHADOW_FREQ_CONFIG2_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x002c)
+#define OMAP4_CM_SHADOW_FREQ_CONFIG1_RESTORE_OFFSET	0x0030
+#define OMAP4430_CM_SHADOW_FREQ_CONFIG1_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0030)
+#define OMAP4_CM_AUTOIDLE_DPLL_CORE_RESTORE_OFFSET	0x0034
+#define OMAP4430_CM_AUTOIDLE_DPLL_CORE_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0034)
+#define OMAP4_CM_MPU_CLKSTCTRL_RESTORE_OFFSET		0x0038
+#define OMAP4430_CM_MPU_CLKSTCTRL_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0038)
+#define OMAP4_CM_CM1_PROFILING_CLKCTRL_RESTORE_OFFSET	0x003c
+#define OMAP4430_CM_CM1_PROFILING_CLKCTRL_RESTORE	OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x003c)
+#define OMAP4_CM_DYN_DEP_PRESCAL_RESTORE_OFFSET		0x0040
+#define OMAP4430_CM_DYN_DEP_PRESCAL_RESTORE		OMAP44XX_CM1_REGADDR(OMAP4430_CM1_RESTORE_MOD, 0x0040)
+
 /* CM2 */
 
 /* CM2.OCP_SOCKET_CM2 register offsets */
@@ -252,8 +288,6 @@
 #define OMAP4430_CM_SSC_DELTAMSTEP_DPLL_PER		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_CKGEN_MOD, 0x0068)
 #define OMAP4_CM_SSC_MODFREQDIV_DPLL_PER_OFFSET		0x006c
 #define OMAP4430_CM_SSC_MODFREQDIV_DPLL_PER		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_CKGEN_MOD, 0x006c)
-#define OMAP4_CM_EMU_OVERRIDE_DPLL_PER_OFFSET		0x0070
-#define OMAP4430_CM_EMU_OVERRIDE_DPLL_PER		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_CKGEN_MOD, 0x0070)
 #define OMAP4_CM_CLKMODE_DPLL_USB_OFFSET		0x0080
 #define OMAP4430_CM_CLKMODE_DPLL_USB			OMAP44XX_CM2_REGADDR(OMAP4430_CM2_CKGEN_MOD, 0x0080)
 #define OMAP4_CM_IDLEST_DPLL_USB_OFFSET			0x0084
@@ -296,6 +330,8 @@
 #define OMAP4430_CM_ALWON_SR_IVA_CLKCTRL		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_ALWAYS_ON_MOD, 0x0030)
 #define OMAP4_CM_ALWON_SR_CORE_CLKCTRL_OFFSET		0x0038
 #define OMAP4430_CM_ALWON_SR_CORE_CLKCTRL		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_ALWAYS_ON_MOD, 0x0038)
+#define OMAP4_CM_ALWON_USBPHY_CLKCTRL_OFFSET		0x0040
+#define OMAP4430_CM_ALWON_USBPHY_CLKCTRL		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_ALWAYS_ON_MOD, 0x0040)
 
 /* CM2.CORE_CM2 register offsets */
 #define OMAP4_CM_L3_1_CLKSTCTRL_OFFSET			0x0000
@@ -578,4 +614,54 @@
 #define OMAP4430_CM_CEFUSE_CLKSTCTRL			OMAP44XX_CM2_REGADDR(OMAP4430_CM2_CEFUSE_MOD, 0x0000)
 #define OMAP4_CM_CEFUSE_CEFUSE_CLKCTRL_OFFSET		0x0020
 #define OMAP4430_CM_CEFUSE_CEFUSE_CLKCTRL		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_CEFUSE_MOD, 0x0020)
+
+/* CM2.RESTORE_CM2 register offsets */
+#define OMAP4_CM_L3_1_CLKSTCTRL_RESTORE_OFFSET		0x0000
+#define OMAP4430_CM_L3_1_CLKSTCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0000)
+#define OMAP4_CM_L3_2_CLKSTCTRL_RESTORE_OFFSET		0x0004
+#define OMAP4430_CM_L3_2_CLKSTCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0004)
+#define OMAP4_CM_L4CFG_CLKSTCTRL_RESTORE_OFFSET		0x0008
+#define OMAP4430_CM_L4CFG_CLKSTCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0008)
+#define OMAP4_CM_MEMIF_CLKSTCTRL_RESTORE_OFFSET		0x000c
+#define OMAP4430_CM_MEMIF_CLKSTCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x000c)
+#define OMAP4_CM_L4PER_CLKSTCTRL_RESTORE_OFFSET		0x0010
+#define OMAP4430_CM_L4PER_CLKSTCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0010)
+#define OMAP4_CM_L3INIT_CLKSTCTRL_RESTORE_OFFSET	0x0014
+#define OMAP4430_CM_L3INIT_CLKSTCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0014)
+#define OMAP4_CM_L3INSTR_L3_3_CLKCTRL_RESTORE_OFFSET	0x0018
+#define OMAP4430_CM_L3INSTR_L3_3_CLKCTRL_RESTORE	OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0018)
+#define OMAP4_CM_L3INSTR_L3_INSTR_CLKCTRL_RESTORE_OFFSET	0x001c
+#define OMAP4430_CM_L3INSTR_L3_INSTR_CLKCTRL_RESTORE	OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x001c)
+#define OMAP4_CM_L3INSTR_OCP_WP1_CLKCTRL_RESTORE_OFFSET	0x0020
+#define OMAP4430_CM_L3INSTR_OCP_WP1_CLKCTRL_RESTORE	OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0020)
+#define OMAP4_CM_CM2_PROFILING_CLKCTRL_RESTORE_OFFSET	0x0024
+#define OMAP4430_CM_CM2_PROFILING_CLKCTRL_RESTORE	OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0024)
+#define OMAP4_CM_D2D_STATICDEP_RESTORE_OFFSET		0x0028
+#define OMAP4430_CM_D2D_STATICDEP_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0028)
+#define OMAP4_CM_L3_1_DYNAMICDEP_RESTORE_OFFSET		0x002c
+#define OMAP4430_CM_L3_1_DYNAMICDEP_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x002c)
+#define OMAP4_CM_L3_2_DYNAMICDEP_RESTORE_OFFSET		0x0030
+#define OMAP4430_CM_L3_2_DYNAMICDEP_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0030)
+#define OMAP4_CM_D2D_DYNAMICDEP_RESTORE_OFFSET		0x0034
+#define OMAP4430_CM_D2D_DYNAMICDEP_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0034)
+#define OMAP4_CM_L4CFG_DYNAMICDEP_RESTORE_OFFSET	0x0038
+#define OMAP4430_CM_L4CFG_DYNAMICDEP_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0038)
+#define OMAP4_CM_L4PER_DYNAMICDEP_RESTORE_OFFSET	0x003c
+#define OMAP4430_CM_L4PER_DYNAMICDEP_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x003c)
+#define OMAP4_CM_L4PER_GPIO2_CLKCTRL_RESTORE_OFFSET	0x0040
+#define OMAP4430_CM_L4PER_GPIO2_CLKCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0040)
+#define OMAP4_CM_L4PER_GPIO3_CLKCTRL_RESTORE_OFFSET	0x0044
+#define OMAP4430_CM_L4PER_GPIO3_CLKCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0044)
+#define OMAP4_CM_L4PER_GPIO4_CLKCTRL_RESTORE_OFFSET	0x0048
+#define OMAP4430_CM_L4PER_GPIO4_CLKCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0048)
+#define OMAP4_CM_L4PER_GPIO5_CLKCTRL_RESTORE_OFFSET	0x004c
+#define OMAP4430_CM_L4PER_GPIO5_CLKCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x004c)
+#define OMAP4_CM_L4PER_GPIO6_CLKCTRL_RESTORE_OFFSET	0x0050
+#define OMAP4430_CM_L4PER_GPIO6_CLKCTRL_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0050)
+#define OMAP4_CM_L3INIT_USB_HOST_CLKCTRL_RESTORE_OFFSET	0x0054
+#define OMAP4430_CM_L3INIT_USB_HOST_CLKCTRL_RESTORE	OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0054)
+#define OMAP4_CM_L3INIT_USB_TLL_CLKCTRL_RESTORE_OFFSET	0x0058
+#define OMAP4430_CM_L3INIT_USB_TLL_CLKCTRL_RESTORE	OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x0058)
+#define OMAP4_CM_SDMA_STATICDEP_RESTORE_OFFSET		0x005c
+#define OMAP4430_CM_SDMA_STATICDEP_RESTORE		OMAP44XX_CM2_REGADDR(OMAP4430_CM2_RESTORE_MOD, 0x005c)
 #endif

arch/arm/mach-omap2/cm4xxx.c

@@ -43,7 +43,6 @@
  *                 using separate functional clock
  *   0x3 disabled: Module is disabled and cannot be accessed
  *
- * TODO: Need to handle module accessible in idle state
  */
 int omap4_cm_wait_module_ready(void __iomem *clkctrl_reg)
 {
@@ -52,9 +51,11 @@ int omap4_cm_wait_module_ready(void __iomem *clkctrl_reg)
 	if (!clkctrl_reg)
 		return 0;
 
-	omap_test_timeout(((__raw_readl(clkctrl_reg) &
-			    OMAP4430_IDLEST_MASK) == 0),
-			  MAX_MODULE_READY_TIME, i);
+	omap_test_timeout((
+		((__raw_readl(clkctrl_reg) & OMAP4430_IDLEST_MASK) == 0) ||
+		 (((__raw_readl(clkctrl_reg) & OMAP4430_IDLEST_MASK) >>
+		  OMAP4430_IDLEST_SHIFT) == 0x2)),
+		MAX_MODULE_READY_TIME, i);
 
 	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
 }

arch/arm/mach-omap2/common.c

+/*
+ * linux/arch/arm/mach-omap2/common.c
+ *
+ * Code common to all OMAP2+ machines.
+ *
+ * Copyright (C) 2009 Texas Instruments
+ * Copyright (C) 2010 Nokia Corporation
+ * Tony Lindgren <tony@atomide.com>
+ * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <plat/common.h>
+#include <plat/board.h>
+#include <plat/mux.h>
+
+#include <plat/clock.h>
+
+#include "sdrc.h"
+#include "control.h"
+
+/* Global address base setup code */
+
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
+
+static void __init __omap2_set_globals(struct omap_globals *omap2_globals)
+{
+	omap2_set_globals_tap(omap2_globals);
+	omap2_set_globals_sdrc(omap2_globals);
+	omap2_set_globals_control(omap2_globals);
+	omap2_set_globals_prcm(omap2_globals);
+}
+
+#endif
+
+#if defined(CONFIG_ARCH_OMAP2420)
+
+static struct omap_globals omap242x_globals = {
+	.class	= OMAP242X_CLASS,
+	.tap	= OMAP2_L4_IO_ADDRESS(0x48014000),
+	.sdrc	= OMAP2420_SDRC_BASE,
+	.sms	= OMAP2420_SMS_BASE,
+	.ctrl	= OMAP242X_CTRL_BASE,
+	.prm	= OMAP2420_PRM_BASE,
+	.cm	= OMAP2420_CM_BASE,
+	.uart1_phys	= OMAP2_UART1_BASE,
+	.uart2_phys	= OMAP2_UART2_BASE,
+	.uart3_phys	= OMAP2_UART3_BASE,
+};
+
+void __init omap2_set_globals_242x(void)
+{
+	__omap2_set_globals(&omap242x_globals);
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP2430)
+
+static struct omap_globals omap243x_globals = {
+	.class	= OMAP243X_CLASS,
+	.tap	= OMAP2_L4_IO_ADDRESS(0x4900a000),
+	.sdrc	= OMAP243X_SDRC_BASE,
+	.sms	= OMAP243X_SMS_BASE,
+	.ctrl	= OMAP243X_CTRL_BASE,
+	.prm	= OMAP2430_PRM_BASE,
+	.cm	= OMAP2430_CM_BASE,
+	.uart1_phys	= OMAP2_UART1_BASE,
+	.uart2_phys	= OMAP2_UART2_BASE,
+	.uart3_phys	= OMAP2_UART3_BASE,
+};
+
+void __init omap2_set_globals_243x(void)
+{
+	__omap2_set_globals(&omap243x_globals);
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP3)
+
+static struct omap_globals omap3_globals = {
+	.class	= OMAP343X_CLASS,
+	.tap	= OMAP2_L4_IO_ADDRESS(0x4830A000),
+	.sdrc	= OMAP343X_SDRC_BASE,
+	.sms	= OMAP343X_SMS_BASE,
+	.ctrl	= OMAP343X_CTRL_BASE,
+	.prm	= OMAP3430_PRM_BASE,
+	.cm	= OMAP3430_CM_BASE,
+	.uart1_phys	= OMAP3_UART1_BASE,
+	.uart2_phys	= OMAP3_UART2_BASE,
+	.uart3_phys	= OMAP3_UART3_BASE,
+	.uart4_phys	= OMAP3_UART4_BASE,	/* Only on 3630 */
+};
+
+void __init omap2_set_globals_3xxx(void)
+{
+	__omap2_set_globals(&omap3_globals);
+}
+
+void __init omap3_map_io(void)
+{
+	omap2_set_globals_3xxx();
+	omap34xx_map_common_io();
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP4)
+static struct omap_globals omap4_globals = {
+	.class	= OMAP443X_CLASS,
+	.tap	= OMAP2_L4_IO_ADDRESS(OMAP443X_SCM_BASE),
+	.ctrl	= OMAP443X_SCM_BASE,
+	.ctrl_pad	= OMAP443X_CTRL_BASE,
+	.prm	= OMAP4430_PRM_BASE,
+	.cm	= OMAP4430_CM_BASE,
+	.cm2	= OMAP4430_CM2_BASE,
+	.uart1_phys	= OMAP4_UART1_BASE,
+	.uart2_phys	= OMAP4_UART2_BASE,
+	.uart3_phys	= OMAP4_UART3_BASE,
+	.uart4_phys	= OMAP4_UART4_BASE,
+};
+
+void __init omap2_set_globals_443x(void)
+{
+	omap2_set_globals_tap(&omap4_globals);
+	omap2_set_globals_control(&omap4_globals);
+	omap2_set_globals_prcm(&omap4_globals);
+}
+#endif
+

arch/arm/mach-omap2/control.c

@@ -16,15 +16,18 @@
 #include <linux/io.h>
 
 #include <plat/common.h>
-#include <plat/control.h>
 #include <plat/sdrc.h>
+
 #include "cm-regbits-34xx.h"
 #include "prm-regbits-34xx.h"
 #include "cm.h"
 #include "prm.h"
 #include "sdrc.h"
+#include "pm.h"
+#include "control.h"
 
 static void __iomem *omap2_ctrl_base;
+static void __iomem *omap4_ctrl_pad_base;
 
 #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
 struct omap3_scratchpad {
@@ -137,6 +140,7 @@ static struct omap3_control_regs control_context;
 #endif /* CONFIG_ARCH_OMAP3 && CONFIG_PM */
 
 #define OMAP_CTRL_REGADDR(reg)		(omap2_ctrl_base + (reg))
+#define OMAP4_CTRL_PAD_REGADDR(reg)	(omap4_ctrl_pad_base + (reg))
 
 void __init omap2_set_globals_control(struct omap_globals *omap2_globals)
 {
@@ -145,6 +149,12 @@ void __init omap2_set_globals_control(struct omap_globals *omap2_globals)
 		omap2_ctrl_base = ioremap(omap2_globals->ctrl, SZ_4K);
 		WARN_ON(!omap2_ctrl_base);
 	}
+
+	/* Static mapping, never released */
+	if (omap2_globals->ctrl_pad) {
+		omap4_ctrl_pad_base = ioremap(omap2_globals->ctrl_pad, SZ_4K);
+		WARN_ON(!omap4_ctrl_pad_base);
+	}
 }
 
 void __iomem *omap_ctrl_base_get(void)
@@ -182,6 +192,23 @@ void omap_ctrl_writel(u32 val, u16 offset)
 	__raw_writel(val, OMAP_CTRL_REGADDR(offset));
 }
 
+/*
+ * On OMAP4 control pad are not addressable from control
+ * core base. So the common omap_ctrl_read/write APIs breaks
+ * Hence export separate APIs to manage the omap4 pad control
+ * registers. This APIs will work only for OMAP4
+ */
+
+u32 omap4_ctrl_pad_readl(u16 offset)
+{
+	return __raw_readl(OMAP4_CTRL_PAD_REGADDR(offset));
+}
+
+void omap4_ctrl_pad_writel(u32 val, u16 offset)
+{
+	__raw_writel(val, OMAP4_CTRL_PAD_REGADDR(offset));
+}
+
 #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
 /*
  * Clears the scratchpad contents in case of cold boot-
@@ -190,7 +217,7 @@ void omap_ctrl_writel(u32 val, u16 offset)
 void omap3_clear_scratchpad_contents(void)
 {
 	u32 max_offset = OMAP343X_SCRATCHPAD_ROM_OFFSET;
-	u32 *v_addr;
+	void __iomem *v_addr;
 	u32 offset = 0;
 	v_addr = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD_ROM);
 	if (prm_read_mod_reg(OMAP3430_GR_MOD, OMAP3_PRM_RSTST_OFFSET) &
@@ -206,7 +233,7 @@ void omap3_clear_scratchpad_contents(void)
 /* Populate the scratchpad structure with restore structure */
 void omap3_save_scratchpad_contents(void)
 {
-	void * __iomem scratchpad_address;
+	void  __iomem *scratchpad_address;
 	u32 arm_context_addr;
 	struct omap3_scratchpad scratchpad_contents;
 	struct omap3_scratchpad_prcm_block prcm_block_contents;

arch/arm/plat-omap/include/plat/control.h → arch/arm/mach-omap2/control.h

 /*
- * arch/arm/plat-omap/include/mach/control.h
+ * arch/arm/mach-omap2/control.h
  *
  * OMAP2/3/4 System Control Module definitions
  *
- * Copyright (C) 2007-2009 Texas Instruments, Inc.
- * Copyright (C) 2007-2008 Nokia Corporation
+ * Copyright (C) 2007-2010 Texas Instruments, Inc.
+ * Copyright (C) 2007-2008, 2010 Nokia Corporation
  *
  * Written by Paul Walmsley
  *
@@ -13,10 +13,14 @@
  * the Free Software Foundation.
  */
 
-#ifndef __ASM_ARCH_CONTROL_H
-#define __ASM_ARCH_CONTROL_H
+#ifndef __ARCH_ARM_MACH_OMAP2_CONTROL_H
+#define __ARCH_ARM_MACH_OMAP2_CONTROL_H
 
 #include <mach/io.h>
+#include <mach/ctrl_module_core_44xx.h>
+#include <mach/ctrl_module_wkup_44xx.h>
+#include <mach/ctrl_module_pad_core_44xx.h>
+#include <mach/ctrl_module_pad_wkup_44xx.h>
 
 #ifndef __ASSEMBLY__
 #define OMAP242X_CTRL_REGADDR(reg)					\
@@ -204,12 +208,6 @@
 #define OMAP3_PADCONF_SAD2D_MSTANDBY   0x250
 #define OMAP3_PADCONF_SAD2D_IDLEACK    0x254
 
-/* 44xx control status register offset */
-#define OMAP44XX_CONTROL_STATUS		0x2c4
-
-/* 44xx-only CONTROL_GENERAL register offsets */
-#define OMAP44XX_CONTROL_MMC1			0x628
-#define OMAP44XX_CONTROL_PBIAS_LITE		0x600
 /*
  * REVISIT: This list of registers is not comprehensive - there are more
  * that should be added.
@@ -225,6 +223,8 @@
 #define OMAP2_MMCSDIO1ADPCLKISEL	(1 << 24) /* MMC1 loop back clock */
 #define OMAP24XX_USBSTANDBYCTRL		(1 << 15)
 #define OMAP2_MCBSP2_CLKS_MASK		(1 << 6)
+#define OMAP2_MCBSP1_FSR_MASK		(1 << 4)
+#define OMAP2_MCBSP1_CLKR_MASK		(1 << 3)
 #define OMAP2_MCBSP1_CLKS_MASK		(1 << 2)
 
 /* CONTROL_DEVCONF1 bits */
@@ -255,23 +255,6 @@
 #define OMAP2_PBIASLITEPWRDNZ0		(1 << 1)
 #define OMAP2_PBIASLITEVMODE0		(1 << 0)
 
-/* CONTROL_PBIAS_LITE bits for OMAP4 */
-#define OMAP4_MMC1_PWRDNZ			(1 << 26)
-#define OMAP4_MMC1_PBIASLITE_HIZ_MODE		(1 << 25)
-#define OMAP4_MMC1_PBIASLITE_SUPPLY_HI_OUT	(1 << 24)
-#define OMAP4_MMC1_PBIASLITE_VMODE_ERROR	(1 << 23)
-#define OMAP4_MMC1_PBIASLITE_PWRDNZ		(1 << 22)
-#define OMAP4_MMC1_PBIASLITE_VMODE		(1 << 21)
-#define OMAP4_USBC1_ICUSB_PWRDNZ		(1 << 20)
-
-#define OMAP4_CONTROL_SDMMC1_PUSTRENGTHGRP0	(1 << 31)
-#define OMAP4_CONTROL_SDMMC1_PUSTRENGTHGRP1	(1 << 30)
-#define OMAP4_CONTROL_SDMMC1_PUSTRENGTHGRP2	(1 << 29)
-#define OMAP4_CONTROL_SDMMC1_PUSTRENGTHGRP3	(1 << 28)
-#define OMAP4_CONTROL_SDMMC1_DR0_SPEEDCTRL	(1 << 27)
-#define OMAP4_CONTROL_SDMMC1_DR1_SPEEDCTRL	(1 << 26)
-#define OMAP4_CONTROL_SDMMC1_DR2_SPEEDCTRL	(1 << 25)
-
 /* CONTROL_PROG_IO1 bits */
 #define OMAP3630_PRG_SDMMC1_SPEEDCTRL	(1 << 20)
 
@@ -338,12 +321,12 @@
 #define		FEAT_L2CACHE_256KB	3
 
 #define OMAP3_ISP_SHIFT			5
-#define OMAP3_ISP_MASK			(1<< OMAP3_ISP_SHIFT)
+#define OMAP3_ISP_MASK			(1 << OMAP3_ISP_SHIFT)
 #define		FEAT_ISP		0
 #define		FEAT_ISP_NONE		1
 
 #define OMAP3_NEON_SHIFT		4
-#define OMAP3_NEON_MASK			(1<< OMAP3_NEON_SHIFT)
+#define OMAP3_NEON_MASK			(1 << OMAP3_NEON_SHIFT)
 #define		FEAT_NEON		0
 #define		FEAT_NEON_NONE		1
 
@@ -354,9 +337,11 @@ extern void __iomem *omap_ctrl_base_get(void);
 extern u8 omap_ctrl_readb(u16 offset);
 extern u16 omap_ctrl_readw(u16 offset);
 extern u32 omap_ctrl_readl(u16 offset);
+extern u32 omap4_ctrl_pad_readl(u16 offset);
 extern void omap_ctrl_writeb(u8 val, u16 offset);
 extern void omap_ctrl_writew(u16 val, u16 offset);
 extern void omap_ctrl_writel(u32 val, u16 offset);
+extern void omap4_ctrl_pad_writel(u32 val, u16 offset);
 
 extern void omap3_save_scratchpad_contents(void);
 extern void omap3_clear_scratchpad_contents(void);
@@ -371,11 +356,13 @@ extern void omap3_control_restore_context(void);
 #define omap_ctrl_readb(x)		0
 #define omap_ctrl_readw(x)		0
 #define omap_ctrl_readl(x)		0
+#define omap4_ctrl_pad_readl(x)		0
 #define omap_ctrl_writeb(x, y)		WARN_ON(1)
 #define omap_ctrl_writew(x, y)		WARN_ON(1)
 #define omap_ctrl_writel(x, y)		WARN_ON(1)
+#define omap4_ctrl_pad_writel(x, y)	WARN_ON(1)
 #endif
 #endif	/* __ASSEMBLY__ */
 
-#endif /* __ASM_ARCH_CONTROL_H */
+#endif /* __ARCH_ARM_MACH_OMAP2_CONTROL_H */
 

arch/arm/mach-omap2/cpuidle34xx.c

@@ -29,10 +29,10 @@
 #include <plat/irqs.h>
 #include <plat/powerdomain.h>
 #include <plat/clockdomain.h>
-#include <plat/control.h>
 #include <plat/serial.h>
 
 #include "pm.h"
+#include "control.h"
 
 #ifdef CONFIG_CPU_IDLE
 
@@ -60,7 +60,8 @@ struct omap3_processor_cx {
 
 struct omap3_processor_cx omap3_power_states[OMAP3_MAX_STATES];
 struct omap3_processor_cx current_cx_state;
-struct powerdomain *mpu_pd, *core_pd;
+struct powerdomain *mpu_pd, *core_pd, *per_pd;
+struct powerdomain *cam_pd;
 
 /*
  * The latencies/thresholds for various C states have
@@ -233,14 +234,60 @@ static int omap3_enter_idle_bm(struct cpuidle_device *dev,
 			       struct cpuidle_state *state)
 {
 	struct cpuidle_state *new_state = next_valid_state(dev, state);
+	u32 core_next_state, per_next_state = 0, per_saved_state = 0;
+	u32 cam_state;
+	struct omap3_processor_cx *cx;
+	int ret;
 
 	if ((state->flags & CPUIDLE_FLAG_CHECK_BM) && omap3_idle_bm_check()) {
 		BUG_ON(!dev->safe_state);
 		new_state = dev->safe_state;
+		goto select_state;
 	}
 
+	cx = cpuidle_get_statedata(state);
+	core_next_state = cx->core_state;
+
+	/*
+	 * FIXME: we currently manage device-specific idle states
+	 *        for PER and CORE in combination with CPU-specific
+	 *        idle states.  This is wrong, and device-specific
+	 *        idle managment needs to be separated out into 
+	 *        its own code.
+	 */
+
+	/*
+	 * Prevent idle completely if CAM is active.
+	 * CAM does not have wakeup capability in OMAP3.
+	 */
+	cam_state = pwrdm_read_pwrst(cam_pd);
+	if (cam_state == PWRDM_POWER_ON) {
+		new_state = dev->safe_state;
+		goto select_state;
+	}
+
+	/*
+	 * Prevent PER off if CORE is not in retention or off as this
+	 * would disable PER wakeups completely.
+	 */
+	per_next_state = per_saved_state = pwrdm_read_next_pwrst(per_pd);
+	if ((per_next_state == PWRDM_POWER_OFF) &&
+	    (core_next_state > PWRDM_POWER_RET))
+		per_next_state = PWRDM_POWER_RET;
+
+	/* Are we changing PER target state? */
+	if (per_next_state != per_saved_state)
+		pwrdm_set_next_pwrst(per_pd, per_next_state);
+
+select_state:
 	dev->last_state = new_state;
-	return omap3_enter_idle(dev, new_state);
+	ret = omap3_enter_idle(dev, new_state);
+
+	/* Restore original PER state if it was modified */
+	if (per_next_state != per_saved_state)
+		pwrdm_set_next_pwrst(per_pd, per_saved_state);
+
+	return ret;
 }
 
 DEFINE_PER_CPU(struct cpuidle_device, omap3_idle_dev);
@@ -328,7 +375,8 @@ void omap_init_power_states(void)
 			cpuidle_params_table[OMAP3_STATE_C2].threshold;
 	omap3_power_states[OMAP3_STATE_C2].mpu_state = PWRDM_POWER_ON;
 	omap3_power_states[OMAP3_STATE_C2].core_state = PWRDM_POWER_ON;
-	omap3_power_states[OMAP3_STATE_C2].flags = CPUIDLE_FLAG_TIME_VALID;
+	omap3_power_states[OMAP3_STATE_C2].flags = CPUIDLE_FLAG_TIME_VALID |
+				CPUIDLE_FLAG_CHECK_BM;
 
 	/* C3 . MPU CSWR + Core inactive */
 	omap3_power_states[OMAP3_STATE_C3].valid =
@@ -426,6 +474,8 @@ int __init omap3_idle_init(void)
 
 	mpu_pd = pwrdm_lookup("mpu_pwrdm");
 	core_pd = pwrdm_lookup("core_pwrdm");
+	per_pd = pwrdm_lookup("per_pwrdm");
+	cam_pd = pwrdm_lookup("cam_pwrdm");
 
 	omap_init_power_states();
 	cpuidle_register_driver(&omap3_idle_driver);

arch/arm/mach-omap2/hsmmc.h

@@ -10,7 +10,8 @@ struct mmc_card;
 
 struct omap2_hsmmc_info {
 	u8	mmc;		/* controller 1/2/3 */
-	u8	wires;		/* 1/4/8 wires */
+	u32	caps;		/* 4/8 wires and any additional host
+				 * capabilities OR'd (ref. linux/mmc/host.h) */
 	bool	transceiver;	/* MMC-2 option */
 	bool	ext_clock;	/* use external pin for input clock */
 	bool	cover_only;	/* No card detect - just cover switch */

arch/arm/mach-omap2/include/mach/board-rx51.h

+/*
+ * Defines for rx51 boards
+ */
+
+#ifndef _OMAP_BOARD_RX51_H
+#define _OMAP_BOARD_RX51_H
+
+extern void __init rx51_peripherals_init(void);
+extern void __init rx51_video_mem_init(void);
+
+#endif

arch/arm/mach-omap2/include/mach/board-zoom.h

 /*
  * Defines for zoom boards
  */
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-
 #define ZOOM_NAND_CS    0
 
-extern void __init board_nand_init(struct mtd_partition *, u8 nr_parts, u8 cs);
 extern int __init zoom_debugboard_init(void);
 extern void __init zoom_peripherals_init(void);
 

arch/arm/mach-omap2/io.c

@@ -36,6 +36,7 @@
 #include "clock2xxx.h"
 #include "clock3xxx.h"
 #include "clock44xx.h"
+#include "io.h"
 
 #include <plat/omap-pm.h>
 #include <plat/powerdomain.h>
@@ -323,6 +324,9 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
 		omap2430_hwmod_init();
 	else if (cpu_is_omap34xx())
 		omap3xxx_hwmod_init();
+	else if (cpu_is_omap44xx())
+		omap44xx_hwmod_init();
+
 	/* The OPP tables have to be registered before a clk init */
 	omap_pm_if_early_init(mpu_opps, dsp_opps, l3_opps);
 
@@ -342,9 +346,7 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
 #ifndef CONFIG_PM_RUNTIME
 	skip_setup_idle = 1;
 #endif
-	if (cpu_is_omap24xx() || cpu_is_omap34xx())   /* FIXME: OMAP4 */
-		omap_hwmod_late_init(skip_setup_idle);
-
+	omap_hwmod_late_init(skip_setup_idle);
 	if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
 		omap2_sdrc_init(sdrc_cs0, sdrc_cs1);
 		_omap2_init_reprogram_sdrc();