Marvell and GPIO bindings live in their own files, so the TOC should not
mention them.

Also fix chapters numbering.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix obvious cases of "it's" being used when "its" was meant.
Signed-off-by: NFrancis Galiegue <fgaliegue@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Split device tree binding out of booting-without-of.txt and put them
into their own files per binding.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix various typos in documentation txts.
Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

It's easier to find bindings descriptions in separate files.  So factor
out the MTD physmap bindings into a separate file to not clutter
booting-without-of.txt more.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Commit d0fc2eaa "powerpc/fsl: Refactor
device bindings" split out a number of device bindings from
booting-without-of.txt into separate files.  Having them all in one file
was a frequent source of merge conflicts.

However, in the next merge, 49997d75, there
was another conflict.  Some of the bindings removed from
booting-without-of.txt were mistakenly added back in and the copies in
dts-bindings were kept as well.

This patch re-removes "Freescale Display Interface" and "Freescale on board
FPGA" and fixes the table of contents.
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The patch allows to specify that an SPI device needs an active high chip
select.
Signed-off-by: NWolfgang Ocker <weo@reccoware.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

from include/asm-powerpc.  This is the result of a

mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm

Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly.  Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add documentation about how to describe SPI busses in the device tree.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSegher Boessenkool <segher@kernel.crashing.org>

Convert to DTS version 1, eliminate some obsolete practices, and
correct some errors (compared to the actual 8540 device tree).
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Moved Freescale SoC related bindings out of booting-without-of.txt and into
their own files.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.

The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is needed to access QE GPIOs via Linux GPIO API.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

GTM stands for General-purpose Timers Module and able to generate
timer{1,2,3,4} interrupts. These timers are used by the drivers that
need time precise interrupts (like for USB transactions scheduling for
the Freescale USB Host controller as found in some QE and CPM chips),
or these timers could be used as wakeup events from the CPU deep-sleep
mode.

Things unimplemented:
1. Cascaded (32 bit) timers (1-2, 3-4).
   This is straightforward to implement when needed, two timers should
   be marked as "requested" and configured as appropriate.
2. Super-cascaded (64 bit) timers (1-2-3-4).
   This is also straightforward to implement when needed, all timers
   should be marked as "requested" and configured as appropriate.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Removed clock-frequency, big-endian, and built-in props as they aren't
specified anywhere.  Also added compatible = "chrp,open-pic" in the
places it was missing.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Binding document adding for Freescale PCIe MSI support.
Signed-off-by: NJason Jin <Jason.jin@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds an MDIO bitbang driver that uses the GPIO library and its
OF bindings to access the bus I/Os.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs

All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0.  Changing pixel clock has no effect
on other fbs.

Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0

required command line parameters to preallocate memory for frame buffer diufb.

optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:

Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60

Bpp
bpp=32, bpp=24, or bpp=16

Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS

Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.

If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NTimur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based addressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.

This code updates the of_serial driver to handle the reg-offset
and reg-shift properties to enable this core to be used.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

- get rid of `model = "UCC"' in the ucc nodes
  It isn't used anywhere, so remove it. If we'll ever need something
  like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
  Drivers are modified for backward compatibility's sake.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This implements support for the GPIO LIB API.  Two calls are still
unimplemented though: irq_to_gpio and gpio_to_irq.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add the device tree bindings for the Marvell mv64x60 series of
system controller chips in booting-without-of.text.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch alters the bootwrapper for a number of machines (roubhly
all 4xx based cuboot or treeboot platforms) to use aliases instead of
the linux,network-index hack to work out which MAC address to attach
to which ethernet device node.

The now obsolete linux,network-index properties are removed from the
corresponding device trees.  This won't break backwards compatiblity,
because in cases where this fixup code is relevant, the device tree is
part of the kernel image.

The references to linux,network-index are removed from
booting-without-of.txt.  Not only is it now deprecated, but as a hack
applicable only when the device tree blob and fixup code were in the
same image, this property never belonged in booting-without-of.txt
which describes the interface between the kernel and firmware or
bootloaders which produce a device tree.  By the time the device tree
reaches the kernel, all the MAC addresses must be fully filled in.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Adds EHCI OF bindings to documentation.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The ICAP device in Xilinx FPGAs differs slightly between different
FPGAs.  The driver needs an additional attribute in the device tree to
distinguish this.
Signed-off-by: NStephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Also:
- rename "fsl_spi" to "fsl,spi";
- add and use cell-index property, if found;
- split probing code out of fsl_spi_init, thus we can call
  it for legacy device_type probing and new "compatible" probing.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".

Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NEbony Zhu <ebony.zhu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Update the MPC8610 HPCD files to support the audio driver.  Update
booting-without-of.txt with information on the SSI device.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for UART serial ports using a Freescale QUICCEngine. Update
booting-without-of.txt to define new properties for a QE UART node.  Update
the MPC8323E-MDS device tree to add UCC5 as a UART.  Update the QE library
to support slow UCC devices and modules.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it.  Add function qe_upload_firmware() to parse the blob
and perform the actual upload.  Fully define 'struct rsp' in immap_qe.h to
include the actual RISC Special Registers.  Added description of a new
QE firmware node to booting-without-of.txt.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

fixed-link says: register new "Fixed/emulated PHY", i.e. PHY that
not connected to the real MDIO bus.
Signed-off-by: NVitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix error in booting-without-of.txt that indicates that a node can inherit
its #address-cells and #size-cells definitions from its parent's parent.
This is not correct.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fix documentation once and for ever, because I'm pretty tired of
repeating that I am merely following it. ;-)

http://ozlabs.org/pipermail/linuxppc-dev/2007-December/048096.html

http://ozlabs.org/pipermail/linuxppc-dev/2007-November/046977.html
http://ozlabs.org/pipermail/linuxppc-dev/2007-November/046979.html

http://ozlabs.org/pipermail/linuxppc-dev/2007-October/044411.html
http://ozlabs.org/pipermail/linuxppc-dev/2007-October/044413.htmlSigned-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This now better describes what the UBoot device tree generator
actually does.  In particular:

1) Nodes have a label derived from the device name, and a node name
derived from a generic version of the device type, e.g. 'ethernet',
'serial', etc.

2) Usage of compound nodes (representing more than one device in the
same IP) which actually works.  This requires having a valid
compatible node, and all the other things that a bus normally has.
I've chosen 'xlnx,compound' as the bus name to describe these compound
nodes.

In addition, I've clarified some of the language relating to how mhs
nodes should be represent in the device tree.
Signed-off-by: NStephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>