In order to support Infiniband fabric, we need to introduce IB speeds and
capabilities to PTYS emads.
Signed-off-by: NElad Raz <eladr@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We want to add Infiniband support to PTYS. In order to maintain proper
conventions, we will change pack and unpack prefix to eth.
Signed-off-by: NElad Raz <eladr@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SwitchX-2 we configure the port speed to negotiate with 40G link only.
Add support for all other supported speeds.

Fixes: 31557f0f ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: NElad Raz <eladr@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export to userspace the front panel name of the port, so that udev can
rename the ports accordingly. The convention suggested by switchdev
documentation is used: pX
Signed-off-by: NElad Raz <eladr@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Be symmentrical with create and do the check outside the remove function.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Be symmentrical with create and do the check outside the remove function.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do it in a same way we do it in spectrum. Check if port is usable first
and only in that case create a port instance.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NElad Raz <eladr@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We recently discovered a bug in the firmware in which a field's length in
one of the registers was incorrectly set. This caused the firmware to
access garbage data that wasn't initialized by the driver and therefore
emit error messages.

While the bug is already fixed and the driver usually zeros the buffers
passed to the firmware, there are a handful of cases where this isn't
done. Zero the buffer in these cases and prevent similar bugs from
recurring, as they tend to be hard to debug.

Fixes: 52581961 ("mlxsw: core: Implement fan control using hwmon")
Signed-off-by: NElad Raz <eladr@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mostly simple overlapping changes.

For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "Lots of fixes, mostly drivers as is usually the case.

   1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
      Khoroshilov.

   2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
      Pedersen.

   3) Don't put aead_req crypto struct on the stack in mac80211, from
      Ard Biesheuvel.

   4) Several uninitialized variable warning fixes from Arnd Bergmann.

   5) Fix memory leak in cxgb4, from Colin Ian King.

   6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.

   7) Several VRF semantic fixes from David Ahern.

   8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.

   9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.

  10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.

  11) Fix stale link state during failover in NCSCI driver, from Gavin
      Shan.

  12) Fix netdev lower adjacency list traversal, from Ido Schimmel.

  13) Propvide proper handle when emitting notifications of filter
      deletes, from Jamal Hadi Salim.

  14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.

  15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.

  16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.

  17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.

  18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
      Leitner.

  19) Revert a netns locking change that causes regressions, from Paul
      Moore.

  20) Add recursion limit to GRO handling, from Sabrina Dubroca.

  21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.

  22) Avoid accessing stale vxlan/geneve socket in data path, from
      Pravin Shelar"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
  geneve: avoid using stale geneve socket.
  vxlan: avoid using stale vxlan socket.
  qede: Fix out-of-bound fastpath memory access
  net: phy: dp83848: add dp83822 PHY support
  enic: fix rq disable
  tipc: fix broadcast link synchronization problem
  ibmvnic: Fix missing brackets in init_sub_crq_irqs
  ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
  Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
  arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
  net/mlx4_en: Save slave ethtool stats command
  net/mlx4_en: Fix potential deadlock in port statistics flow
  net/mlx4: Fix firmware command timeout during interrupt test
  net/mlx4_core: Do not access comm channel if it has not yet been initialized
  net/mlx4_en: Fix panic during reboot
  net/mlx4_en: Process all completions in RX rings after port goes up
  net/mlx4_en: Resolve dividing by zero in 32-bit system
  net/mlx4_core: Change the default value of enable_qos
  net/mlx4_core: Avoid setting ports to auto when only one port type is supported
  net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
  ...

The maximum unicast datagram size /without/ link fragmentation is
4096 - 4 = 4092 (max IEEE 1394 async payload size at >= S800 bus speed,
minus unfragmented encapssulation header).  Max broadcast datagram size
without fragmentation is 8 bytes less than that (due to GASP header).

The maximum datagram size /with/ link fragmentation is 0xfff = 4095
for unicast and broadcast.  This is because the RFC 2734 fragment
encapsulation header field for datagram size is only 12 bits wide.

Fixes: 5d48f00d('firewire: net: fix maximum possible MTU')
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a typo in unregister operation.

Following crash is fixed by this patch. It can be easily reproduced
by repeating modprobe and rmmod module that uses genetlink.

[  261.446686] BUG: unable to handle kernel paging request at ffffffffa0264088
[  261.448921] IP: [<ffffffff813cb70e>] strcmp+0xe/0x30
[  261.450494] PGD 1c09067
[  261.451266] PUD 1c0a063
[  261.452091] PMD 8068d5067
[  261.452525] PTE 0
[  261.453164]
[  261.453618] Oops: 0000 [#1] SMP
[  261.454577] Modules linked in: openvswitch(+) ...
[  261.480753] RIP: 0010:[<ffffffff813cb70e>]  [<ffffffff813cb70e>] strcmp+0xe/0x30
[  261.483069] RSP: 0018:ffffc90003c0bc28  EFLAGS: 00010282
[  261.510145] Call Trace:
[  261.510896]  [<ffffffff816f10ca>] genl_family_find_byname+0x5a/0x70
[  261.512819]  [<ffffffff816f2319>] genl_register_family+0xb9/0x630
[  261.514805]  [<ffffffffa02840bc>] dp_init+0xbc/0x120 [openvswitch]
[  261.518268]  [<ffffffff8100217d>] do_one_initcall+0x3d/0x160
[  261.525041]  [<ffffffff811808a9>] do_init_module+0x60/0x1f1
[  261.526754]  [<ffffffff8110687f>] load_module+0x22af/0x2860
[  261.530144]  [<ffffffff81107026>] SYSC_finit_module+0x96/0xd0
[  261.531901]  [<ffffffff8110707e>] SyS_finit_module+0xe/0x10
[  261.533605]  [<ffffffff8100391e>] do_syscall_64+0x6e/0x180
[  261.535284]  [<ffffffff817c2faf>] entry_SYSCALL64_slow_path+0x25/0x25
[  261.546512] RIP  [<ffffffff813cb70e>] strcmp+0xe/0x30
[  261.550198] ---[ end trace 76505a814dd68770 ]---

Fixes: 2ae0f17d ("genetlink: use idr to track families").
Reported-by: NJarno Rajahalme <jarno@ovn.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is similar to earlier vxlan patch.
Geneve device close operation frees geneve socket. This
operation can race with geneve-xmit function which
dereferences geneve socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When vxlan device is closed vxlan socket is freed. This
operation can race with vxlan-xmit function which
dereferences vxlan socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.

To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRaju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: NAllan W. Nielsen <allan.nielsen@microsemi.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2016-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Among various cleanups and improvements, we have the following:
 * client FILS authentication support in mac80211 (Jouni)
 * AP/VLAN multicast improvements (Michael Braun)
 * config/advertising support for differing beacon intervals on
   multiple virtual interfaces (Purushottam Kushwaha, myself)
 * deprecate the old WDS mode for cfg80211-based drivers, the
   mode is hardly usable since it doesn't support any "modern"
   features like WPA encryption (2003), HT (2009) or VHT (2014),
   I'm not even sure WEP (introduced in 1997) could be done.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This PHY has a compatible register set with DP83848x so
add support for it.
Acked-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When MTU is changed from 9000 to 1500 while there is burst of inbound 9000
bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes
buffers. This causes memory corruption and sometimes crash.

This is because of a race condition in adaptor between "RQ disable"
clearing descriptor mini-cache and mini-cache valid bit being set by
completion of descriptor fetch. This can result in stale RQ desc being
cached and used when packets arrive. In this case, the stale descriptor
have old MTU value.

Solution is to write RQ->disable twice. The first write will stop any
further desc fetches, allowing the second disable to clear the mini-cache
valid bit without danger of a race.

Also, the check for rq->running becoming 0 after writing rq->enable to 0
is not done properly. When incoming packets are flooding the interface,
rq->running will pulse high for each dropped packet. Since the driver was
waiting for 10us between each poll, it is possible to see rq->running = 1
1000 times in a row, even though it is not actually stuck running.
This results in false failure of vnic_rq_disable(). Fix is to try more
than 1000 time without delay between polls to ensure we do not miss when
running goes low.

In old adaptors rq->enable needs to be re-written to 0 when posted_index
is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 2d18ac4b ("tipc: extend broadcast link initialization
criteria") we tried to fix a problem with the initial synchronization
of broadcast link acknowledge values. Unfortunately that solution is
not sufficient to solve the issue.

We have seen it happen that LINK_PROTOCOL/STATE packets with a valid
non-zero unicast acknowledge number may bypass BCAST_PROTOCOL
initialization, NAME_DISTRIBUTOR and other STATE packets with invalid
broadcast acknowledge numbers, leading to premature opening of the
broadcast link. When the bypassed packets finally arrive, they are
inadvertently accepted, and the already correctly initialized
acknowledge number in the broadcast receive link is overwritten by
the invalid (zero) value of the said packets. After this the broadcast
link goes stale.

We now fix this by marking the packets where we know the acknowledge
value is or may be invalid, and then ignoring the acks from those.

To this purpose, we claim an unused bit in the header to indicate that
the value is invalid. We set the bit to 1 in the initial BCAST_PROTOCOL
synchronization packet and all initial ("bulk") NAME_DISTRIBUTOR
packets, plus those LINK_PROTOCOL packets sent out before the broadcast
links are fully synchronized.

This minor protocol update is fully backwards compatible.
Reported-by: NJohn Thompson <thompa.atl@gmail.com>
Tested-by: NJohn Thompson <thompa.atl@gmail.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 8d7533e5.

It introduced kbuild failures, new version coming.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do this so the sysfs has "device" link correctly set.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2016-10-27

This series contains fixes to ixgbe and i40e.

Emil fixes a NULL pointer dereference when a macvlan interface is brought
up while the PF is still down.

David root caused the original panic that was fixed by commit id
(a036244c "i40e: Fix kernel panic on enable/disable LLDP") and the
fix was not quite correct, so removed the get_default_tc() and replaced
it with a #define since there is only one TC supported as a default.

Guilherme Piccoli fixes an issue where if we modprobe the driver module
without enough MSI-X interrupts, then unload the module and reload it
again, the kernel would crash.  So if we fail to allocate enough MSI-X
interrupts, we should disable them since they were previously enabled.

Huaibin Wang found that the order of the arguments for
ndo_dflt_bridge_getlink() were in the correct order, so fix the order.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Document the possible state transitions for a BBR flow, and also add a
prose summary of the state machine, covering the life of a typical BBR
flow.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 01cfbad7 "ipv4: Update parameters for csum_tcpudp_magic to their
original types" changed parameters for csum_tcpudp_magic and
csum_tcpudp_nofold for many platforms but not for PowerPC.

Fixes: 01cfbad7 "ipv4: Update parameters for csum_tcpudp_magic to their original types"
Cc: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull x86 bugfix from Thomas Gleixner:
 "A single bugfix for the recent changes related to registering the boot
  cpu when this has not happened before prefill_possible_map().

  The main problem with this change got fixed already, but we missed the
  case where the local APIC is not yet mapped, when prefill_possible_map()
  is invoked, so the registration of the boot cpu which has the APIC bit
  set in CPUID will explode.

  I should have seen that issue earlier, but all I can do now is feeling
  embarassed"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smpboot: Init apic mapping before usage

Simon Wunderlich says:

====================
This code cleanup patchset includes the following changes (chronological
order):

 - bump version strings, by Simon Wunderlich

 - README updates/clean up, by Sven Eckelmann (4 patches)

 - Code clean up and restructuring by Sven Eckelmann (2 patches)

 - Kerneldoc fix in forw_packet structure, by Linus Luessing

 - Remove unused argument in dbg_arp, by Antonio Quartulli

 - Add support to build batman-adv without wireless, by Linus Luessing

 - Restructure error handling for is_ap_isolated, by Markus Elfring

 - Remove unused initialization in various functions, by Sven Eckelmann

 - Use better names for fragment and gateway list heads, by Sven
   Eckelmann (2 patches)

 - Convert to octal permissions for files, by Sven Eckelmann

 - Avoid precedence issues for some macros, by Sven Eckelmann
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tariq Toukan says:

====================
mlx4 misc fixes for 4.9

This patchset contains several bug fixes from the team to the
mlx4 Eth and Core drivers.

Series generated against net commit:
ecc515d7 'sctp: fix the panic caused by route update'
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following the previous patch, as an optimization, the slave will
not even bother sending the DUMP_ETH_STATS command over the
comm channel.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then
called the FW command, with WRAPPED attribute. As a result, the fw command
is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS.
The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex*
during processing.

At the same time, a VF could be in the process of coming up, and could
call mlx4_QUERY_FUNC_CAP.  On the hypervisor, the command flow takes the
*slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper.
mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(),
which takes the *counter mutex*. DEADLOCK.

The fix is that the DUMP_ETH_STATS fw command should be called with
the NATIVE attribute, so that on the hypervisor, this command does not
enter the wrapper flow.

Since the Hypervisor no longer goes through the wrapper code, we also
simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds,
but the returned data will be all zeroes).
No need to test if it is the Hypervisor going through the wrapper.

Fixes: f9baff50 ("mlx4_core: Add "native" argument to mlx4_cmd ...")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently interrupt test that is part of ethtool selftest runs the
check over all interrupt vectors of the device.
In mlx4_en package part of interrupt vectors are uninitialized since
mlx4_ib doesn't exist. This causes NOP FW command to time out.
Change logic to test current port interrupt vectors only.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the Hypervisor, there are several FW commands which are invoked
before the comm channel is initialized (in mlx4_multi_func_init).
These include MOD_STAT_CONFIG, QUERY_DEV_CAP, INIT_HCA, and others.

If any of these commands fails, say with a timeout, the Hypervisor
driver enters the internal error reset flow. In this flow, the driver
attempts to notify all slaves via the comm channel that an internal error
has occurred.

Since the comm channel has not yet been initialized (i.e., mapped via
ioremap), this will cause dereferencing a NULL pointer.

To fix this, do not access the comm channel in the internal error flow
if it has not yet been initialized.

Fixes: 55ad3592 ("net/mlx4_core: Enable device recovery flow with SRIOV")
Fixes: ab9c17a0 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a kernel panic that occurs as a result of an asynchronous event
handled in roce_gid_mgmt:
mlx4_en_get_drvinfo is called and accesses freed resources.

This happens in a shutdown flow only, since pci device is destroyed
while netdevice is still alive.

Fixes: c27a02cd ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there is a race between incoming traffic and
initialization flow. HW is able to receive the packets
after INIT_PORT is done and unicast steering is configured.
Before we set priv->port_up NAPI is not scheduled and
receive queues become full. Therefore we never get
new interrupts about the completions.
This issue could happen if running heavy traffic during
bringing port up.
The resolution is to schedule NAPI once port_up is set.
If receive queues were full this will process all cqes
and release them.

Fixes: c27a02cd ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing roundup_pow_of_two for large enough number with
bit 31, an overflow will occur and a value equal to 1 will
be returned. In this case 1 will be subtracted from the return
value and division by zero will be reached.

Fixes: 31c128b6 ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the default status of quality of service back to disabled,
as it hurts performance in some cases.

Fixes: 38438f7c ("net/mlx4: Set enhanced QoS support by default when ...")
Signed-off-by: NMoshe Lazer <moshel@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When only one port type is supported, it should be read only.
We reject changing requests, even to the auto sense mode.

Fixes: 27bf91d6 ("mlx4_core: Add link type autosensing")
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>