When we're moving a port from Learning or Forwarding state to Disabled
or Blocking or Listening state, remove all non-static MAC addresses
mapped to this port in the entire set of databases, not only one.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new _mv88e6xxx_atu_move function to prepare the ATU data register
for the move operation. The ports vector will contain the source port
and destination port of the Move operation. If the destination port is
0xF, the MAC addresses mapped to the source port are removed for the
address database(s).

Then add a _mv88e6xxx_atu_remove wrapper to remove the MAC addresses
from a VLAN database that are mapped to a given port, when it leaves it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When choosing an address database for a new VLAN, flush every entries,
not only the non-static ones.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Purge all MAC addresses from the entire set of address databases when
the driver initializes the device.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These Marvell switches have 4 operations to flush or (re)move, all or
only non-static MAC addresses, from the entire set of databases or from
just a particular one.

The value of the EntryState bits will determine if the operation is
either a Flush (0x0) or a Move (0xF).

When moving entries from one port to another, entries will be removed if
the destination port is 0xF.

This patch renames these operations for consistency, add a new generic
_mv88e6xxx_atu_flush_move function, and change _mv88e6xxx_flush_fid to
use it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other ATU commands need to write the ATU data register. To ease the
introduction of such commands, extract the ATU data write access from
_mv88e6xxx_atu_load to its own function.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not every ATU commands apply to an FID, thus remove the FID writing from
mv88e6xxx_atu_cmd and write it explicitly where needed, in order to ease
introduction of such commands.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the FIB table id to rtable to make the information available for
IPv4 as it is for IPv6.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Typo that snuck in with commit 6979c630Signed-off-by: NRoy Spliet <rspliet@eclipso.eu>
Reported-by: NPierre Moreau <pierre.morrow@free.fr>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Broken since "gr: convert user classes to new-style nvkm_object"

Tested on a PPC64 G5 + NV34
Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Due to some recent changes in
drm_helper_probe_single_connector_modes_merge_bits(), old custom modes
were not being pruned properly. In current kernels,
drm_mode_validate_basic() is called to sanity-check each mode in the
list. If the sanity-check passes, the mode's status gets set to to
MODE_OK. In older kernels this check was not done, so old custom modes
would still have a status of MODE_UNVERIFIED at this point, and would
therefore be pruned later in the function.

As a result of this new behavior, the list of modes for a device always
includes every custom mode ever configured for the device, with the
largest one listed first. Since desktop environments usually choose the
first preferred mode when a hotplug event is emitted, this had the
result of making it very difficult for the user to reduce the size of
the display.

The qxl driver did implement the mode_valid connector function, but it
was empty. In order to restore the old behavior where old custom modes
are pruned, we implement a proper mode_valid function for the qxl
driver. This function now checks each mode against the last configured
custom mode and the list of standard modes. If the mode doesn't match
any of these, its status is set to MODE_BAD so that it will be pruned as
expected.
Signed-off-by: NJonathon Jongsma <jjongsma@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Since 2009 we have a nice asm-generic header implementing lots of DMA API
functions for architectures using struct dma_map_ops, but unfortunately
it's still missing a lot of APIs that all architectures still have to
duplicate.

This series consolidates the remaining functions, although we still need
arch opt outs for two of them as a few architectures have very
non-standard implementations.

This patch (of 5):

The coherent DMA allocator works the same over all architectures supporting
dma_map operations.

This patch consolidates them and converges the minor differences:

 - the debug_dma helpers are now called from all architectures, including
   those that were previously missing them
 - dma_alloc_from_coherent and dma_release_from_coherent are now always
   called from the generic alloc/free routines instead of the ops
   dma-mapping-common.h always includes dma-coherent.h to get the defintions
   for them, or the stubs if the architecture doesn't support this feature
 - checks for ->alloc / ->free presence are removed.  There is only one
   magic instead of dma_map_ops without them (mic_dma_ops) and that one
   is x86 only anyway.

Besides that only x86 needs special treatment to replace a default devices
if none is passed and tweak the gfp_flags.  An optional arch hook is provided
for that.

[linux@roeck-us.net: fix build]
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With two exceptions (drm/qxl and drm/radeon) all vm_operations_struct
structs should be constant.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: NOleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are two kexec load syscalls, kexec_load another and kexec_file_load.
 kexec_file_load has been splited as kernel/kexec_file.c.  In this patch I
split kexec_load syscall code to kernel/kexec.c.

And add a new kconfig option KEXEC_CORE, so we can disable kexec_load and
use kexec_file_load only, or vice verse.

The original requirement is from Ted Ts'o, he want kexec kernel signature
being checked with CONFIG_KEXEC_VERIFY_SIG enabled.  But kexec-tools use
kexec_load syscall can bypass the checking.

Vivek Goyal proposed to create a common kconfig option so user can compile
in only one syscall for loading kexec kernel.  KEXEC/KEXEC_FILE selects
KEXEC_CORE so that old config files still work.

Because there's general code need CONFIG_KEXEC_CORE, so I updated all the
architecture Kconfig with a new option KEXEC_CORE, and let KEXEC selects
KEXEC_CORE in arch Kconfig.  Also updated general kernel code with to
kexec_load syscall.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NDave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of custom approach let's use recently introduced seq_hex_dump()
helper.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of custom approach let's use recently introduced seq_hex_dump()
helper.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NIngo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of custom approach let's use recently introduced seq_hex_dump()
helper.

In one case it changes the output from
	1111111122222222333333334444444455555555666666667777777788888888
to
	11111111 22222222 33333333 44444444 55555555 66666666 77777777 88888888

though it seems it prints same data (by meaning) in both cases.  I decide
to choose to use the space divided one.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NHelge Deller <deller@gmx.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of custom approach let's use recently introduced seq_hex_dump()
helper.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NTadeusz Struk <tadeusz.struk@intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Originally that parameter was always reset to num_online_cpus during
module initialisation, which renders it useless.

The fix is to only set max_queues to num_online_cpus when user has not
provided a value.
Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Tested-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Originally that parameter was always reset to num_online_cpus during
module initialisation, which renders it useless.

The fix is to only set max_queues to num_online_cpus when user has not
provided a value.
Reported-by: NJohnny Strom <johnny.strom@linuxsolutions.fi>
Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=104031
Fixes: 6e85d5ad

Based on the discussion starting at
http://www.spinics.net/lists/netdev/msg342193.html

Tested locally on RTL8168evl/8111evl with various concurrent processes
accessing /proc/net/dev while changing the link state as well as
removing/reloading the r8169 module.
Signed-off-by: NCorinna Vinschen <vinschen@redhat.com>
Tested-by: Npoma <pomidorabelisima@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just like single link MIPI panels, similarly for dual link panels, pipe
to be configured is based on the DVO port from VBT Block 2. In hardware,
Port A is mapped with Pipe A and Port C is mapped with Pipe B.

This issue got introduced in -

commit 7e9804fd
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Fri Jan 16 14:27:23 2015 +0200

    drm/i915/dsi: add drm mipi dsi host support

Cc: stable@vger.kernel.org # v4.0
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

If one disables DDR DVFS in the BIOS, Punit will apparently ignores
all DDR DVFS request. Currently we assume that DDR DVFS is always
operational, which leads to errors in dmesg when the DDR DVFS requests
time out.

Fix the problem by gently prodding Punit during driver load to find out
whether it will respond to DDR DVFS requests. If the request times out,
we assume that DDR DVFS has been permanenly disabled in the BIOS and
no longer perster the Punit about it.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91629Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NClint Taylor <Clinton.A.Taylor@intel.com>
Tested-by: NClint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Fix a wrong logical AND (&&) used for the range check of CSR MMIO.

Spotted nicely by gcc -Wlogical-op flag:
  drivers/gpu/drm/i915/intel_csr.c: In function ‘finish_csr_load’:
  drivers/gpu/drm/i915/intel_csr.c:353:41: warning: logical ‘and’ of mutually exclusive tests is always false [-Wlogical-op]

Fixes: eb805623 ('drm/i915/skl: Add support to load SKL CSR firmware.')
Cc: <stable@vger.kernel.org> # v4.2
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Incorporate fw_ldst_cmd structure change for new firmware and also
update version string for the same
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There exist one issue by below case that case system hang:
ifconfig eth0 down
ifconfig eth0 hw ether 00:10:19:19:81:19

After eth0 down, all fec clocks are gated off. In the .fec_set_mac_address()
function, it will set new MAC address to registers, which causes system hang.

So it needs to add netif status check to avoid registers access when clocks are
gated off. Until eth0 up the new MAC address are wrote into related registers.

V2:
As Lucas Stach's suggestion, add a comment in the code to explain why it needed.

CC: Lucas Stach <l.stach@pengutronix.de>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the runtime suspend issues result from the linking change.

Case 1:
a) link down occurs.
b) driver disable tx/rx.
c) autosuspend occurs.
d) hw linking up.
e) device suspends without enabling tx/rx.
f) couldn't wake up when receiving packets.

Case 2:
a) Nway results in linking down.
b) autosuspend occurs.
c) device suspends.
d) device may not wake up when linking up.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split DRIVER_VERSION into NETNEXT_VERSION and NET_VERSION. Then,
according to the value of DRIVER_VERSION, we could know which
patches are used generally without comparing the source code.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Microchip LAN88XX phy driver for phylib.
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current check of phydev with IS_ERR(phydev) may make not much sense
because of_phy_connect() returns NULL on failure instead of error value.

Still for checking result of phy_connect() IS_ERR() makes perfect sense.

So let's use combined check IS_ERR_OR_NULL() that covers both cases.

Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In all cases, mbx->req.arg and mbx->rsp.arg have just been allocated
using kcalloc(), so these six memsets are redundant.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The double memset is a little ugly; using kzalloc avoids it altogether.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using kzalloc saves a tiny bit on .text.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We save a little .text and get rid of the sizeof(...) style
inconsistency.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For !CONFIG_OF of_get_property() is defined to always return NULL. Thus
there's no need to protect the call to of_get_property() with #ifdef
CONFIG_OF.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macro to write 64-bits quantities to the 32-bits register swapped
the value and offsets arguments, we want to preserve the ordering of the
arguments with respect to how writel() is implemented for instance:
value first, offset/base second.

Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fBLOCKREADINTR is masking the notification from the remote and should
hence be cleared while we're waiting the tx fifo to drain. Also change
the reset state to mask the notification, as send is the only use case
where we're interested in it.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NAndy Gross <agross@codeaurora.org>

This patch fixes SMEM addressing issues when remote processors need to use
secure SMEM partitions.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Reviewed-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>

This patch corrects private partition item access.  Instead of falling back to
global for instances where we have an actual host and remote partition existing,
return the results of the private lookup.
Signed-off-by: NAndy Gross <agross@codeaurora.org>