This moves us one more step closer to eliminating the soc-camera bus
and devices on it. Besides, as a side effect, CSI-2 runtime PM on
sh-mobile secomes finer grained now: we only have to power on the
interface, when the device nodes are open.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

soc-camera host drivers shall be implementing their PM, using standard
kernel methods, soc-camera specific hooks can die.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The pxa-camera driver doesn't need soc-camera specific PM callbacks,
switch it to using the standard PM hooks instead.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently available two hardware revision:
0x1	firmware filename: dvb-netup-altera-01.fw
0x4	firmware filename: dvb-netup-altera-04.fw
Signed-off-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently available two hardware revision:
0x1	firmware filename: dvb-netup-altera-01.fw
0x4	firmware filename: dvb-netup-altera-04.fw
Signed-off-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add two fields to the ISP parallel platform data to set the HS and VS
signals polarities.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current omap3isp driver is missing regulator handling
for CSIb complex in omap34xx based devices. This patch
adds a mechanism for this to the omap3isp driver.
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Minor changes to remove the unused code from omap_vout driver.
Signed-off-by: NAmber Jain <amber@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support to map the buffer using dma_map_single during qbuf which inturn
calls cache flush and unmap the same during dqbuf. This is done to prevent
the artifacts seen because of cache-coherency issues on OMAP4
Signed-off-by: NAmber Jain <amber@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Extending the omap vout isr handling for:
- HDMI interface.

These are the new interfaces added to OMAP4 DSS.
Signed-off-by: NAmber Jain <amber@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Introduce omap_vout_vrfb.c and omap_vout_vrfb.h, for all VRFB related API's,
making OMAP_VOUT driver independent from VRFB. This is required for OMAP4 DSS,
since OMAP4 doesn't have VRFB block.

Added new enum vout_rotation_type and "rotation_type" member to omapvideo_info,
this is initialized based on the arch type in omap_vout_probe. The rotation_type
var is now used to choose between vrfb and non-vrfb calls.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rename rotation_enabled() and rotate_90_or_270() to is_rotation_enabled()
and is_rotation_90_or_270() to make them more descriptive.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move the inline functions rotate_90_or_270(), rotation_enabled(), and
calc_rotation() from omap_vout.c to omap_voutdef.h.

Move the independent functions omap_vout_alloc_buffer() and
omap_vout_free_buffer() to omap_voutlib.c.

Remove extern identifier from function definitions in omap_voutlib.h

Add static identifier to functions that are used locally in omap_vout.c
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove GFP_DMA from the __get_free_pages() call from omap24xxcam as ZONE_DMA
is not configured on OMAP. Earlier the page allocator used to return a page
from ZONE_NORMAL even when GFP_DMA is passed and CONFIG_ZONE_DMA is disabled.
As a result of commit a197b59a, page allocator
returns null in such a scenario with a warning emitted to kernel log.
Signed-off-by: NAmber Jain <amber@ti.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove GFP_DMA from the __get_free_pages() call from omap_vout as ZONE_DMA
is not configured on OMAP. Earlier the page allocator used to return a page
from ZONE_NORMAL even when GFP_DMA is passed and CONFIG_ZONE_DMA is disabled.
As a result of commit a197b59a, page allocator
returns null in such a scenario with a warning emitted to kernel log.
Signed-off-by: NAmber Jain <amber@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The camera there identifies itself as being manufactured by Cheng Uei
Precision Industry Co., Ltd (Foxlink), and product is titled as "HP
Webcam [2 MP Fixed]".

I was trying to get 2 USB video capture devices to work simultaneously,
and noticed that the above mentioned webcam always requires packet size
= 3072 bytes per micro frame (~= 23.4 MB/s isoc bandwidth), which is far
more than enough to get standard NTSC 640x480x2x30 = ~17.6 MB/s isoc
bandwidth.

As there are alt interfaces with smaller MxPS

    T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
    D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
    P:  Vendor=05c8 ProdID=0403 Rev= 1.06
    S:  Manufacturer=Foxlink
    S:  Product=HP Webcam [2 MP Fixed]
    S:  SerialNumber=200909240102
    C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
    A:  FirstIf#= 0 IfCount= 2 Cls=0e(video) Sub=03 Prot=00
    I:* If#= 0 Alt= 0 #EPs= 1 Cls=0e(video) Sub=01 Prot=00 Driver=uvcvideo
    E:  Ad=83(I) Atr=03(Int.) MxPS=  16 Ivl=4ms
    I:* If#= 1 Alt= 0 #EPs= 0 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
    I:  If#= 1 Alt= 1 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
    E:  Ad=81(I) Atr=05(Isoc) MxPS= 128 Ivl=125us
    I:  If#= 1 Alt= 2 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
    E:  Ad=81(I) Atr=05(Isoc) MxPS= 512 Ivl=125us
    I:  If#= 1 Alt= 3 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
    E:  Ad=81(I) Atr=05(Isoc) MxPS=1024 Ivl=125us
    I:  If#= 1 Alt= 4 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
    E:  Ad=81(I) Atr=05(Isoc) MxPS=1536 Ivl=125us
    I:  If#= 1 Alt= 5 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
    E:  Ad=81(I) Atr=05(Isoc) MxPS=2048 Ivl=125us
    I:  If#= 1 Alt= 6 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
    E:  Ad=81(I) Atr=05(Isoc) MxPS=2688 Ivl=125us
    I:  If#= 1 Alt= 7 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
    E:  Ad=81(I) Atr=05(Isoc) MxPS=3072 Ivl=125us

UVC_QUIRK_FIX_BANDWIDTH helps here and NTSC video can be served with
MxPS=2688 i.e. 20.5 MB/s isoc bandwidth.

In terms of microframe time allocation, before the quirk NTSC video
required 60 usecs / microframe and 53 usecs / microframe after.
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NKirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make use of the signal state registers to properly populate the signal lock
registers in the cx231xx driver.

This allows applications to know whether there is a signal present even in
devices which lack a tuner (since such apps typically won't call G_TUNER if
no tuner is present).

[mchehab@redhat.com: Fix CodingStyle: don't use {} for one-line if's]
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On platforms that have CONFIG_HZ set to 100, the power ramp time effectively
ends up being 10ms.  However, on those that have a higher CONFIG_HZ, the time
ends up *actually* being 5ms, which doesn't allow enough time for the hardware
to be fully powered up before attempting to address it via i2c.

Change the constant to 10ms, which is long enough for the hardware to power
up, and won't really be anymore time than it was previously on platforms
with CONFIG_HZ being 100.

Credit goes to Mauro Carvalho Chehab and Gerd Hoffmann who previously
investigated this issue.

Tested with the Hauppauge USBLive 2, with which the problem was readily
reproducible after setting CONFIG_HZ to 1000.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The following patch addresses the regression introduced in the cx231xx
driver which stopped the Hauppauge USBLive2 from working.

Confirmed working by both myself and the user who reported the issue
on the KernelLabs blog (Robert DeLuca).

At some point during refactoring of the cx231xx driver, the USBLive 2 device
became broken.  This patch results in the device working again.

Thanks to Robert DeLuca for sponsoring this work.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Cc: Robert DeLuca <robertdeluca@me.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The search for matching extension units fails to take account of the
current chain.  In the case where you have two distinct video chains,
both containing an XU with the same GUID but different unit ids, you
will be unable to perform a mapping on the second chain because entity
on the first chain will always be found first

Fix this by only searching the current chain when performing a control
mapping.  This is analogous to the search used by uvc_find_control(),
and is the correct behaviour.
Signed-off-by: NStephan Lachowsky <stephan.lachowsky@maxim-ic.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Both ngene and ddbrige calls dvb_attach once for drxk_attach.
The logic used there, and by tda18271c2dd driver is different
from similar logic on other frontends.

The right fix is to change them to use the same logic, but,
while we don't do that, we need to patch em28xx-dvb in order
to do cope with ngene/ddbridge magic.

While here, document why drxk_t_release should do nothing.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The following patch adds a new control that makes it possible to set the
luma notch filter type to finetune picture quality.
Signed-off-by: NIstvan Varga <istvan_v@mailbox.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch implements support for a sharpness control, using the luma
peaking filter feature of cx2388x.

[mchehab@redhat.com: use cx_andor instead of cx_write]
Signed-off-by: NIstvan Varga <istvan_v@mailbox.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add driver for TV Mixer on Samsung platforms from S5P family.
Mixer is responsible for merging images from three layers and
passing result to the output.

Drivers are using:
- v4l2 framework
- videobuf2
- runtime PM
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add drivers for Standard Definition output (SDO) on Samsung platforms
from S5P family. The driver provides control over streaming analog TV
via Composite connector.

Driver is using:
- v4l2 framework
- runtime PM
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add drivers for HDMI outputs on Samsung platforms from S5P family.

Drivers are using:
- v4l2 framework
- runtime PM
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The cx88 driver would force core->input to always be zero when doing the
the request_acquire().  While it wasn't actually changing the input register
in the hardware, the driver makes decision based on the current input.  In
particular, it decides whether to do things like enabling the comb filter
when on a composite input but disabling it on s-video.  So for example, on
the HVR-1300, using the s-video input with the MPEG encoder would end up with
the video decoder core configured as though the input type were composite.

In short, the driver state did not match the hardware state.

This patch does two things:

1.  It forces the input to zero only if actually switching to DVB mode.  This
prevents the input from changing when the blackbird driver opens the device.

2.  Keep track of what the input was set to when switching to DVB, and reset
it back when done.  This eliminates a condition where for example the user
had the analog side of the board set to capture on the s-video input, then
he used DVB for a bit, then the analog input would unexpectedly be set to
the tuner input.

This work was sponsored by Anevia S.A.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Multi Format Codec 5.1 is a hardware video coding acceleration
module found in the S5PV210 and Exynos4 Samsung SoCs. It is
capable of handling a range of video codecs and this driver
provides a V4L2 interface for video decoding and encoding.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Clear the cx231xx_devused variable and free dev in the error handling code,
as done in the error handling code nearby.

The semantic match that finds this problem is as follows:

// <smpl>
@r@
identifier x;
@@

kfree(x)

@@
identifier r.x;
expression E1!=0,E2,E3,E4;
statement S;
@@

(
if (<+...x...+>) S
|
if (...) { ... when != kfree(x)
               when != if (...) { ... kfree(x); ... }
               when != x = E3
* return E1;
}
... when != x = E2
if (...) { ... when != x = E4
 kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Free the recently allocated qcam in each case.

The semantic match that finds this problem is as follows:

// <smpl>
@r@
identifier x;
@@

kfree(x)

@@
identifier r.x;
expression E1!=0,E2,E3,E4;
statement S;
@@

(
if (<+...x...+>) S
|
if (...) { ... when != kfree(x)
               when != if (...) { ... kfree(x); ... }
               when != x = E3
* return E1;
}
... when != x = E2
if (...) { ... when != x = E4
 kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch, based on code by Mirek Slugen, implements support for the
Leadtek WinFast PxDVR3200 H card with XC4000 tuner (107d:6f39).
Signed-off-by: NIstvan Varga <istvan_v@mailbox.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make sure that the 'static' keywork is at the beginning of declaration
for drivers/media/video/omap/omap_vout.c

This gets rid of warnings like
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Delete a couple of leftover fields whose time has passed.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Marvell camera core can support all three videobuf2 buffer modes, which
is slick, but it also requires that all three modes be built and present,
even though only one is likely to be used.  This patch allows the supported
modes to be selected at configuration time, reducing the footprint of the
driver.  Prior to this patch, the MMP camera driver looked like this:

mmp_camera             19092  0
videobuf2_core         15542  1 mmp_camera
videobuf2_dma_sg        3173  1 mmp_camera
videobuf2_dma_contig     2188  1 mmp_camera
videobuf2_vmalloc       1718  1 mmp_camera
videobuf2_memops        2100  3 videobuf2_dma_sg,videobuf2_dma_contig,videobuf2_vmalloc

Afterward, instead, with scatter/gather only configured:

mmp_camera             16021  0
videobuf2_core         15542  1 mmp_camera
videobuf2_dma_sg        3173  1 mmp_camera
videobuf2_memops        2100  1 videobuf2_dma_sg

The total goes from 43,813 bytes to 36,836.

The emphasis has been on simplicity and minimal #ifdef use rather than on
squeezing out every possible byte of code.  For configuration, the driver
simply looks at which videobuf2 modes have been configured in and supports
them all; it's simplistic but should be good enough.

The cafe driver is set to support vmalloc and dma-contig; mmp supports only
dma-sg, since that's the only mode that really makes sense to use.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If registration does not work, we don't want to leave the sensor powered on.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Somewhere along the way the code stopped actually paying any attention to
them, and I doubt anybody has ever made use of them.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>