There is duplicated code which iterates over disk backing stores
performing some action. Provide a convenient helper for doing
this to eliminate duplication & risk of mistakes with disk format
probing

* src/conf/domain_conf.c, src/conf/domain_conf.h,
  src/libvirt_private.syms: Add virDomainDiskDefForeachPath()

The virStorageFileGetMetadataFromFD did two jobs in one. First
it probed for storage type, then it extracted metadata for the
type. It is desirable to be able to separate these jobs, allowing
probing without querying metadata, and querying metadata without
probing.

To prepare for this, split out probing code into a new pair of
methods

  virStorageFileProbeFormatFromFD
  virStorageFileProbeFormat

* src/util/storage_file.c, src/util/storage_file.h,
  src/libvirt_private.syms: Introduce virStorageFileProbeFormat
  and virStorageFileProbeFormatFromFD

The parallel, serial, console and channel devices are all just
character devices. A lot of code needs todo the same thing to
all these devices. This provides an convenient API for iterating
over all of them.

* src/conf/domain_conf.c, src/conf/domain_conf.c,
  src/libvirt_private.syms: Add virDomainChrDefForeach

Following Daniel Berrange's multiple helpful suggestions for improving
this patch and introducing another driver interface, I now wrote the
below patch where the nwfilter driver registers the functions to
instantiate and teardown the nwfilters with a function in
conf/domain_nwfilter.c called virDomainConfNWFilterRegister. Previous
helper functions that were called from qemu_driver.c and qemu_conf.c
were move into conf/domain_nwfilter.h with slight renaming done for
consistency. Those functions now call the function expored by
domain_nwfilter.c, which in turn call the functions of the new driver
interface, if available.

The network driver is not doing correct checking for
duplicate UUID/name values. This introduces a new method
virNetworkObjIsDuplicate, based on the previously
written virDomainObjIsDuplicate.

* src/conf/network_conf.c, src/conf/network_conf.c,
  src/libvirt_private.syms: Add virNetworkObjIsDuplicate,
* src/network/bridge_driver.c: Call virNetworkObjIsDuplicate
  for checking uniqueness of uuid/names

The storage pool driver is not doing correct checking for
duplicate UUID/name values. This introduces a new method
virStoragePoolObjIsDuplicate, based on the previously
written virDomainObjIsDuplicate.

* src/conf/storage_conf.c, src/conf/storage_conf.c,
  src/libvirt_private.syms: Add virStoragePoolObjIsDuplicate,
* src/storage/storage_driver.c: Call virStoragePoolObjIsDuplicate
  for checking uniqueness of uuid/names

This patch that adds support for configuring 802.1Qbg and 802.1Qbh
switches. The 802.1Qbh part has been successfully tested with real
hardware. The 802.1Qbg part has only been tested with a (dummy)
server that 'behaves' similarly to how we expect lldpad to 'behave'.

The following changes were made during the development of this patch:

 - Merging Scott's v13-pre1 patch
 - Fixing endptr related bug while using virStrToLong_ui() pointed out
   by Jim Meyering
 - Addressing Jim Meyering's comments to v11
 - requiring mac address to the vpDisassociateProfileId() function to
   pass it further to the 802.1Qbg disassociate part (802.1Qbh untouched)
 - determining pid of lldpad daemon by reading it from /var/run/libvirt.pid
   (hardcode as is hardcode alson in lldpad sources)
 - merging netlink send code for kernel target and user space target
   (lldpad) using one function nlComm() to send the messages
 - adding a select() after the sending and before the reading of the
   netlink response in case lldpad doesn't respond and so we don't hang
 - when reading the port status, in case of 802.1Qbg, no status may be
   received while things are 'in progress' and only at the end a status
   will be there.
 - when reading the port status, use the given instanceId and vf to pick
   the right IFLA_VF_PORT among those nested under IFLA_VF_PORTS.
 - never sending nor parsing IFLA_PORT_SELF type of messages in the
   802.1Qbg case
 - iterating over the elements in a IFLA_VF_PORTS to pick the right
   IFLA_VF_PORT by either IFLA_PORT_PROFILE and given profileId
   (802.1Qbh) or IFLA_PORT_INSTANCE_UUID and given instanceId (802.1Qbg)
   and reading the current status in IFLA_PORT_RESPONSE.
 - recycling a previous patch that adds functionality to interface.c to
   - get the vlan identifier on an interface
   - get the flags of an interface and some convenience function to
     check whether an interface is 'up' or not (not currently used here)
 - adding function to determine the root physical interface of an
   interface. For example if a macvtap is linked to eth0.100, it will
   find eth0. Also adding a function that finds the vlan on the 'way to
   the root physical interface'
 - conveying the root physical interface name and index in case of 802.1Qbg
 - conveying mac address of macvlan device and vlan identifier in
   IFLA_VFINFO_LIST[ IFLA_VF_INFO[ IFLA_VF_MAC(mac), IFLA_VF_VLAN(vlan) ] ]
   to (future) lldpad via netlink
  - To enable build with --without-macvtap rename the
    [dis|]associatePortProfileId functions, prepend 'vp' before their
    name and make them non-static functions.
  - Renaming variable multicast to nltarget_kernel and inverting
    the logic
  - Addressing Jim Meyering's comments; this also touches existing
    code for example for correcting indentation of break statements or
    simplification of switch statements.
  - Renamed occurrencvirVirtualPortProfileDef to virVirtualPortProfileParamses
  - 802.1Qbg part prepared for sending a RTM_SETLINK and getting
    processing status back plus a subsequent RTM_GETLINK to
    get IFLA_PORT_RESPONSE.
    Note: This interface for 802.1Qbg may still change
  - [David Allan] move getPhysfn inside IFLA_VF_PORT_MAX to avoid
compiler
    warning when latest if_link.h isn't available
  - move from Stefan's 802.1Qb{g|h} XML v8 to v9
  - move hostuuid and vf index calcs to inside doPortProfileOp8021Qbh
  - remove debug fprintfs
  - use virGetHostUUID (thanks Stefan!)
  - fix compile issue when latest if_link.h isn't available
  - change poll timeout to 10s, at 1/8 intervals
     - if polling times out, log msg and return -ETIMEDOUT
  - Add Stefan's code for getPortProfileStatus
  - Poll for up to 2 secs for port-profile status, at 1/8 sec intervals:
     - if status indicates error, abort openMacvtapTap
     - if status indicates success, exit polling
     - if status is "in-progress" after 2 secs of polling, exit
       polling loop silently, without error

My patch finishes out the 802.1Qbh parts, which Stefan had mostly complete.
I've tested using the recent kernel updates for VF_PORT netlink msgs and
enic for Cisco's 10G Ethernet NIC.  I tested many VMs, each with several
direct interfaces, each configured with a port-profile per the XML.  VM-to-VM,
and VM-to-external work as expected.  VM-to-VM on same host (using same NIC)
works same as VM-to-VM where VMs are on diff hosts.  I'm able to change
settings on the port-profile while the VM is running to change the virtual
port behaviour.  For example, adjusting a QoS setting like rate limit.  All
VMs with interfaces using that port-profile immediatly see the effect of the
change to the port-profile.

I don't have a SR-IOV device to test so source dev is a non-SR-IOV device,
but most of the code paths include support for specifing the source dev and
VF index.  We'll need to complete this by discovering the PF given the VF
linkdev.  Once we have the PF, we'll also have the VF index.  All this info-
mation is available from sysfs.

We've been running into a lot of situations where
virGetHostname() is returning "localhost", where a plain
gethostname() would have returned the correct thing.  This
is because virGetHostname() is *always* trying to canonicalize
the name returned from gethostname(), even when it doesn't
have to.

This patch changes virGetHostname so that if the value returned
from gethostname() is already FQDN or localhost, it returns
that string directly.  If the value returned from gethostname()
is a shortened hostname, then we try to canonicalize it.  If
that succeeds, we returned the canonicalized hostname.  If
that fails, and/or returns "localhost", then we just return
the original string we got from gethostname() and hope for
the best.

Note that after this patch it is up to clients to check whether
"localhost" is an allowed return value.  The only place
where it's currently not is in qemu migration.
Signed-off-by: NChris Lalancette <clalance@redhat.com>

Spurious / in a pool target path makes life difficult for apps using the
GetVolByPath, and doing other path based comparisons with pools. This
has caused a few issues for virt-manager users:

https://bugzilla.redhat.com/show_bug.cgi?id=494005
https://bugzilla.redhat.com/show_bug.cgi?id=593565

Add a new util API which removes spurious /, virFileSanitizePath. Sanitize
target paths when parsing pool XML, and for paths passed to GetVolByPath.

v2: Leading // must be preserved, properly sanitize path=/, sanitize
    away /./ -> /

v3: Properly handle starting ./ and ending /.

v4: Drop all '.' handling, just sanitize / for now.

Allow for a host UUID in the capabilities XML. Local drivers
will initialize this from the SMBIOS data. If a sanity check
shows SMBIOS uuid is invalid, allow an override from the
libvirtd.conf configuration file

* daemon/libvirtd.c, daemon/libvirtd.conf: Support a host_uuid
  configuration option
* docs/schemas/capability.rng: Add optional host uuid field
* src/conf/capabilities.c, src/conf/capabilities.h: Include
  host UUID in XML
* src/libvirt_private.syms: Export new uuid.h functions
* src/lxc/lxc_conf.c, src/qemu/qemu_driver.c,
  src/uml/uml_conf.c: Set host UUID in capabilities
* src/util/uuid.c, src/util/uuid.h: Support for host UUIDs
* src/node_device/node_device_udev.c: Use the host UUID functions
* tests/confdata/libvirtd.conf, tests/confdata/libvirtd.out: Add
  new host_uuid config option to test

V2:
  - Move bitmap impl to src/util/bitmap.[ch]
  - Use CHAR_BIT instead of explicit '8'
  - Use size_t instead of unsigned int
  - Fix calculation of bitmap size in virBitmapAlloc
  - Ensure bit is within range of map in the set, clear, and get
    operations
  - Use bool in virBitmapGetBit
  - Add virBitmapFree to free-like funcs in cfg.mk

V3:
  - Check for overflow in virBitmapAlloc
  - Fix copy and paste bug in virBitmapAlloc
  - Use size_t in prototypes
  - Add ATTRIBUTE_NONNULL in prototypes where appropriate
    and remove NULL check from impl

V4:
  - Add ATTRIBUTE_RETURN_CHECK in prototypes where appropriate.

We need to be able to assign new def to an existing virDomainObj which
is already locked. This patch factors out the relevant code from
virDomainAssignDef into virDomainObjAssignDef.

When QEMU runs with its disk on NFS, and as a non-root user, the
disk is chownd to that non-root user. When migration completes
the last step is shutting down the QEMU on the source host. THis
normally resets user/group/security label. This is bad when the
VM was just migrated because the file is still in use on the dest
host. It is thus neccessary to skip the reset step for any files
found to be on a shared filesystem

* src/libvirt_private.syms: Export virStorageFileIsSharedFS
* src/util/storage_file.c, src/util/storage_file.h: Add a new
  method virStorageFileIsSharedFS() to determine if a file is
  on a shared filesystem (NFS, GFS, OCFS2, etc)
* src/qemu/qemu_driver.c: Tell security driver not to reset
  disk labels on migration completion
* src/qemu/qemu_security_dac.c, src/qemu/qemu_security_stacked.c,
  src/security/security_selinux.c, src/security/security_driver.h,
  src/security/security_apparmor.c: Add ability to skip disk
  restore step for files on shared filesystems.

This introduces a new event type

   VIR_DOMAIN_EVENT_ID_IO_ERROR_REASON

This event is the same as the previous VIR_DOMAIN_ID_IO_ERROR
event, but also includes a string describing the cause of
the event.

Thus there is a new callback definition for this event type

typedef void (*virConnectDomainEventIOErrorReasonCallback)(virConnectPtr conn,
                                                           virDomainPtr dom,
                                                           const char *srcPath,
                                                           const char *devAlias,
                                                           int action,
                                                           const char *reason,
                                                           void *opaque);

This is currently wired up to the QEMU block IO error events

* daemon/remote.c: Dispatch IO error events to client
* examples/domain-events/events-c/event-test.c: Watch for
  IO error events
* include/libvirt/libvirt.h.in: Define new IO error event ID
  and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
  src/libvirt_private.syms: Extend API to handle IO error events
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
  for block IO errors and emit a libvirt IO error event
* src/remote/remote_driver.c: Receive and dispatch IO error
  events to application
* src/remote/remote_protocol.x: Wire protocol definition for
  IO error events
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
  src/qemu/qemu_monitor_json.c: Watch for BLOCK_IO_ERROR event
  from QEMU monitor

* po/POTFILES.in: the new module contains translatable strings
* src/Makefile.am: include the files in the utils set
* src/libvirt_private.syms: exports the symbols internally

Changes from v1 to v2:
- changed function name prefixes to 'iface' from previous 'Iface'

- Further to make make syntax-check pass:
 - indentation fix in interface.h
 - added entry to POTFILES.in

I am consolidating network interface related functions used in nwfilter
and macvtap code in utils/interface.c. All function names are prefixed
with 'Iface'. The following functions are now available through
interface.h:

int ifaceCtrl(const char *name, bool up);
int ifaceUp(const char *name);
int ifaceDown(const char *name);

int ifaceCheck(bool reportError, const char *ifname,
               const unsigned char *macaddr, int ifindex);

int ifaceGetIndex(bool reportError, const char *ifname, int *ifindex);

I added 'int ifindex' as parameter to ifaceCheck to the original
function and modified the code accordingly.

This patch implements support for learning a VM's IP address. It uses
the pcap library to listen on the VM's backend network interface (tap)
or the physical ethernet device (macvtap) and tries to capture packets
with source or destination MAC address of the VM and learn from DHCP
Offers, ARP traffic, or first-sent IPv4 packet what the IP address of
the VM's interface is. This then allows to instantiate the network
traffic filtering rules without the user having to provide the IP
parameter somewhere in the filter description or in the interface
description as a parameter. This only supports to detect the parameter
IP, which is for the assumed single IPv4 address of a VM. There is not
support for interfaces that may have multiple  IP addresses (IP
aliasing) or IPv6 that may then require more than one valid IP address
to be detected. A VM can have multiple independent interfaces that each
uses a different IP address and in that case it will be attempted to
detect each one of the address independently.

So, when for example an interface description in the domain XML has
looked like this up to now:

    <interface type='bridge'>
      <source bridge='mybridge'/>
      <model type='virtio'/>
      <filterref filter='clean-traffic'>
        <parameter name='IP' value='10.2.3.4'/>
      </filterref>
    </interface>

you may omit the IP parameter:

    <interface type='bridge'>
      <source bridge='mybridge'/>
      <model type='virtio'/>
      <filterref filter='clean-traffic'/>
    </interface>

Internally I am walking the 'tree' of a VM's referenced network filters
and determine with the given variables which variables are missing. Now,
the above IP parameter may be missing and this causes a libvirt-internal
thread to be started that uses the pcap library's API to listen to the
backend interface  (in case of macvtap to the physical interface) in an
attempt to determine the missing IP parameter. If the backend interface
disappears the thread terminates assuming the VM was brought down. In
case of a macvtap device a timeout is being used to wait for packets
from the given VM (filtering by VM's interface MAC address). If the VM's
macvtap device disappeared the thread also terminates. In all other
cases it tries to determine the IP address of the VM and will then apply
the rules late on the given interface, which would have happened
immediately if the IP parameter had been explicitly given. In case an
error happens while the firewall rules are applied, the VM's backend
interface is 'down'ed preventing it to communicate. Reasons for failure
for applying the network firewall rules may that an ebtables/iptables
command failes or OOM errors. Essentially the same failure reasons may
occur as when the firewall rules are applied immediately on VM start,
except that due to the late application of the filtering rules the VM
now is already running and cannot be hindered anymore from starting.
Bringing down the whole VM would probably be considered too drastic.
While a VM's IP address is attempted to be determined only limited
updates to network filters are allowed. In particular it is prevented
that filters are modified in such a way that they would introduce new
variables.

A caveat: The algorithm does not know which one is the appropriate IP
address of a VM. If the VM spoofs an IP address in its first ARP traffic
or IPv4 packets its filtering rules will be instantiated for this IP
address, thus 'locking' it to the found IP address. So, it's still
'safer' to explicitly provide the IP address of a VM's interface in the
filter description if it is known beforehand.

* configure.ac: detect libpcap
* libvirt.spec.in: require libpcap[-devel] if qemu is built
* src/internal.h: add the new ATTRIBUTE_PACKED define
* src/Makefile.am src/libvirt_private.syms: add the new modules and symbols
* src/nwfilter/nwfilter_learnipaddr.[ch]: new module being added
* src/nwfilter/nwfilter_driver.c src/conf/nwfilter_conf.[ch]
  src/nwfilter/nwfilter_ebiptables_driver.[ch]
  src/nwfilter/nwfilter_gentech_driver.[ch]: plu the new functionality in
* tests/nwfilterxml2xmltest: extend testing

Signed-off-by: NChris Lalancette <clalance@redhat.com>

Signed-off-by: NChris Lalancette <clalance@redhat.com>

The clock timer XML is being updated in the following ways (based on
further off-list discussion that was missed during the initial
implementation):

1) 'wallclock' is changed to 'track', and the possible values are 'boot'
 (corresponds to old 'host'), 'guest', and 'wall'.

2) 'mode' has an additional value 'smpsafe'

3) when tickpolicy='catchup', there can be an optional sub-element of
   timer called 'catchup':

   <catchup threshold=123 slew=120 limit=10000/>

Those three values are all longs, always optional, and if they are present,
they are positive. Internally, 0 indicates "unspecified".

* docs/schemas/domain.rng: updated RNG definition to account for changes

* src/conf/domain_conf.h: change the C struct and enums to match changes.

* src/conf/domain_conf.c: timer parse and format functions changed to
                          handle the new selections and new element.

* src/libvirt_private.syms: *TimerWallclock* changes to *TimerTrack*

* src/qemu/qemu_conf.c: again, account for Wallclock --> Track change.

virParseVersionString uses virStrToLong_ui instead of sscanf.

This also fixes a bug in the UML driver, that always returned 0
as version number.

Introduce STRSKIP to check if a string has a certain prefix and
to skip this prefix.

This extension is described in

http://www.redhat.com/archives/libvir-list/2010-March/msg00304.html

Currently all attributes are optional, except name.

* src/conf/domain_conf.h: add data definition for virDomainTimerDef
  and add a list of them to virDomainClockDef
* src/conf/domain_conf.c: XML parser and formatter for a timer inside a clock
* src/libvirt_private.syms: add new Timer enum helper functions to symbols

This exports 3 basic routines:
  - virHookInitialize() initializing the hook support by looking for
    scripts availability
  - virHookPresent() used to test if there is a hook for a given driver
  - virHookCall() which actually calls a synchronous script hook with
    the needed parameters
Note that this doesn't expose any public API except for the locations
and arguments passed to the scripts

* src/Makefile.am: add the 2 new files
* src/util/hooks.h src/util/hooks.c: implements the 3 functions
* src/libvirt_private.syms: export the 3 symbols internally
* po/POTFILES.in: add src/util/hooks.c to translatables modules

used to read the data from virExec stdout/err file descriptors

* src/util/util.c src/util/util.h: not static anymore and export it
* src/libvirt_private.syms: allow access internally

Useful mainly for migration. cpuUpdate changes guest CPU requirements in
the following way:

- match == "strict" || match == "exact"
    - optional features which are supported by host CPU are changed into
      required features
    - optional features which are not supported by host CPU are disabled
    - all other features remain untouched
- match == "minimum"
    - match is changed into "exact"
    - optional features and all features not mentioned in guest CPU
      specification which are supported by host CPU become required
      features
    - other optional features are disabled
    - all other features remain untouched

This ensures that no feature will suddenly disappear from the guest
after migration.

* Fixes per feedback from Dan and Daniel
* Added test datafiles
* Re-disabled JSON flags
* Added code to print the error policy attribute when generating XML
* Re-add empty tag

This patch adds support for L3/L4 filtering using iptables. This adds
support for 'tcp', 'udp', 'icmp', 'igmp', 'sctp' etc. filtering.

As mentioned in the introduction, a .c file provided by this patch
is #include'd into a .c file. This will need work, but should be alright
for review.
Signed-off-by: NStefan Berger <stefanb@us.ibm.com>

This patch implements the core driver and provides
- management functionality for managing the filter XMLs
- compiling the internal filter representation into ebtables rules
- applying ebtables rules on a network (tap,macvtap) interface
- tearing down ebtables rules that were applied on behalf of an
interface
- updating of filters while VMs are running and causing the firewalls to
be rebuilt
- other bits and pieces
Signed-off-by: NStefan Berger <stefanb@us.ibm.com>

This patch adds the implementation of the public API for the network
filtering (ACL) extensions to libvirt.c .
Signed-off-by: NStefan Berger <stefanb@us.ibm.com>

Use the new virDomainUpdateDeviceFlags API to allow the VNC password
to be changed on the fly

* src/internal.h: Define STREQ_NULLABLE() which is like STREQ()
  but does not crash if either argument is NULL, and treats two
  NULLs as equal.
* src/libvirt_private.syms: Export virDomainGraphicsTypeToString
* src/qemu/qemu_driver.c: Support VNC password change on a live
  machine
* src/qemu/qemu_monitor.c: Disable crazy debugging info. Treat a
  NULL password as "" (empty string), allowing passwords to be
  disabled in the monitor

This introduces a new event type

   VIR_DOMAIN_EVENT_ID_GRAPHICS

The same event can be emitted in 3 scenarios

  typedef enum {
      VIR_DOMAIN_EVENT_GRAPHICS_CONNECT = 0,
      VIR_DOMAIN_EVENT_GRAPHICS_INITIALIZE,
      VIR_DOMAIN_EVENT_GRAPHICS_DISCONNECT,
  } virDomainEventGraphicsPhase;

Connect/disconnect are triggered at socket accept/close.
The initialize phase is immediately after the protocol
setup and authentication has completed. ie when the
client is authorized and about to start interacting with
the graphical desktop

This event comes with *a lot* of potential information

 - IP address, port & address family of client
 - IP address, port & address family of server
 - Authentication scheme (arbitrary string)
 - Authenticated subject identity. A subject may have
   multiple identities with some authentication schemes.
   For example, vencrypt+sasl results in a x509dname
   and saslUsername identities.

This results in a very complicated callback :-(

   typedef enum {
      VIR_DOMAIN_EVENT_GRAPHICS_ADDRESS_IPV4,
      VIR_DOMAIN_EVENT_GRAPHICS_ADDRESS_IPV6,
   } virDomainEventGraphicsAddressType;

   struct _virDomainEventGraphicsAddress {
       int family;
       const char *node;
       const char *service;
   };
   typedef struct _virDomainEventGraphicsAddress virDomainEventGraphicsAddress;
   typedef virDomainEventGraphicsAddress *virDomainEventGraphicsAddressPtr;

   struct _virDomainEventGraphicsSubject {
      int nidentity;
      struct {
          const char *type;
          const char *name;
      } *identities;
   };
   typedef struct _virDomainEventGraphicsSubject virDomainEventGraphicsSubject;
   typedef virDomainEventGraphicsSubject *virDomainEventGraphicsSubjectPtr;

   typedef void (*virConnectDomainEventGraphicsCallback)(virConnectPtr conn,
                                                         virDomainPtr dom,
                                                         int phase,
                                                         virDomainEventGraphicsAddressPtr local,
                                                         virDomainEventGraphicsAddressPtr remote,
                                                         const char *authScheme,
                                                         virDomainEventGraphicsSubjectPtr subject,
                                                         void *opaque);

The wire protocol is similarly complex

   struct remote_domain_event_graphics_address {
     int family;
     remote_nonnull_string node;
     remote_nonnull_string service;
   };

   const REMOTE_DOMAIN_EVENT_GRAPHICS_IDENTITY_MAX = 20;

   struct remote_domain_event_graphics_identity {
     remote_nonnull_string type;
     remote_nonnull_string name;
   };

   struct remote_domain_event_graphics_msg {
     remote_nonnull_domain dom;
     int phase;
     remote_domain_event_graphics_address local;
     remote_domain_event_graphics_address remote;
     remote_nonnull_string authScheme;
     remote_domain_event_graphics_identity subject<REMOTE_DOMAIN_EVENT_GRAPHICS_IDENTITY_MAX>;
   };

This is currently implemented in QEMU for the VNC graphics
protocol, but designed to be usable with SPICE graphics in
the future too.

* daemon/remote.c: Dispatch graphics events to client
* examples/domain-events/events-c/event-test.c: Watch for
  graphics events
* include/libvirt/libvirt.h.in: Define new graphics event ID
  and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
  src/libvirt_private.syms: Extend API to handle graphics events
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
  for VNC events and emit a libvirt graphics event
* src/remote/remote_driver.c: Receive and dispatch graphics
  events to application
* src/remote/remote_protocol.x: Wire protocol definition for
  graphics events
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
  src/qemu/qemu_monitor_json.c: Watch for VNC_CONNECTED,
  VNC_INITIALIZED & VNC_DISCONNETED events from QEMU monitor

This introduces a new event type

   VIR_DOMAIN_EVENT_ID_IO_ERROR

This event includes the action that is about to be taken
as a result of the watchdog triggering

  typedef enum {
     VIR_DOMAIN_EVENT_IO_ERROR_NONE = 0,
     VIR_DOMAIN_EVENT_IO_ERROR_PAUSE,
     VIR_DOMAIN_EVENT_IO_ERROR_REPORT,
  } virDomainEventIOErrorAction;

In addition it has the source path of the disk that had the
error and its unique device alias. It does not include the
target device name (/dev/sda), since this would preclude
triggering IO errors from other file backed devices (eg
serial ports connected to a file)

Thus there is a new callback definition for this event type

typedef void (*virConnectDomainEventIOErrorCallback)(virConnectPtr conn,
                                                     virDomainPtr dom,
                                                     const char *srcPath,
                                                     const char *devAlias,
                                                     int action,
                                                     void *opaque);

This is currently wired up to the QEMU block IO error events

* daemon/remote.c: Dispatch IO error events to client
* examples/domain-events/events-c/event-test.c: Watch for
  IO error events
* include/libvirt/libvirt.h.in: Define new IO error event ID
  and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
  src/libvirt_private.syms: Extend API to handle IO error events
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
  for block IO errors and emit a libvirt IO error event
* src/remote/remote_driver.c: Receive and dispatch IO error
  events to application
* src/remote/remote_protocol.x: Wire protocol definition for
  IO error events
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
  src/qemu/qemu_monitor_json.c: Watch for BLOCK_IO_ERROR event
  from QEMU monitor

This introduces a new event type

   VIR_DOMAIN_EVENT_ID_WATCHDOG

This event includes the action that is about to be taken
as a result of the watchdog triggering

 typedef enum {
     VIR_DOMAIN_EVENT_WATCHDOG_NONE = 0,
     VIR_DOMAIN_EVENT_WATCHDOG_PAUSE,
     VIR_DOMAIN_EVENT_WATCHDOG_RESET,
     VIR_DOMAIN_EVENT_WATCHDOG_POWEROFF,
     VIR_DOMAIN_EVENT_WATCHDOG_SHUTDOWN,
     VIR_DOMAIN_EVENT_WATCHDOG_DEBUG,
 } virDomainEventWatchdogAction;

Thus there is a new callback definition for this event type

 typedef void (*virConnectDomainEventWatchdogCallback)(virConnectPtr conn,
                                                       virDomainPtr dom,
                                                       int action,
                                                       void *opaque);

* daemon/remote.c: Dispatch watchdog events to client
* examples/domain-events/events-c/event-test.c: Watch for
  watchdog events
* include/libvirt/libvirt.h.in: Define new watchdg event ID
  and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
  src/libvirt_private.syms: Extend API to handle watchdog events
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
  for watchdogs and emit a libvirt watchdog event
* src/remote/remote_driver.c: Receive and dispatch watchdog
  events to application
* src/remote/remote_protocol.x: Wire protocol definition for
  watchdog events
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
  src/qemu/qemu_monitor_json.c: Watch for WATCHDOG event
  from QEMU monitor

This introduces a new event type

   VIR_DOMAIN_EVENT_ID_RTC_CHANGE

This event includes the new UTC offset measured in seconds.
Thus there is a new callback definition for this event type

 typedef void (*virConnectDomainEventRTCChangeCallback)(virConnectPtr conn,
                                                        virDomainPtr dom,
                                                        long long utcoffset,
                                                        void *opaque);

If the guest XML configuration for the <clock> is set to
offset='variable', then the XML will automatically be
updated with the new UTC offset value. This ensures that
during migration/save/restore the new offset is preserved.

* daemon/remote.c: Dispatch RTC change events to client
* examples/domain-events/events-c/event-test.c: Watch for
  RTC change events
* include/libvirt/libvirt.h.in: Define new RTC change event ID
  and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
  src/libvirt_private.syms: Extend API to handle RTC change events
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
  for RTC changes and emit a libvirt RTC change event
* src/remote/remote_driver.c: Receive and dispatch RTC change
  events to application
* src/remote/remote_protocol.x: Wire protocol definition for
  RTC change events
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
  src/qemu/qemu_monitor_json.c: Watch for RTC_CHANGE event
  from QEMU monitor

The reboot event is not a normal lifecycle event, since the
virtual machine on the host does not change state. Rather the
guest OS is resetting the virtual CPUs. ie, the QEMU process
does not restart. Thus, this does not belong in the current
lifecycle events callback.

This introduces a new event type

    VIR_DOMAIN_EVENT_ID_REBOOT

It takes no parameters, besides the virDomainPtr, so it can
use the generic callback signature.

* daemon/remote.c: Dispatch reboot events to client
* examples/domain-events/events-c/event-test.c: Watch for
  reboot events
* include/libvirt/libvirt.h.in: Define new reboot event ID
* src/conf/domain_event.c, src/conf/domain_event.h,
  src/libvirt_private.syms: Extend API to handle reboot events
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
  for reboots and emit a libvirt reboot event
* src/remote/remote_driver.c: Receive and dispatch reboot
  events to application
* src/remote/remote_protocol.x: Wire protocol definition for
  reboot events

The current internal domain events API tracks callbacks based on
the function pointer, and only supports lifecycle events. This
adds new internal APIs for registering callbacks for other event
types. These new APIs are postfixed with the word 'ID' to indicate
that they operated based on event ID, instead of hardcoded to
lifecycle events

* src/conf/domain_event.c, src/conf/domain_event.h,
  src/libvirt_private.syms: Add new APIs for handling callbacks
  for non-lifecycle events

This symbol is conditional, it would need to be exported conditional to
work properly with MinGW. So just remove it, as no other driver register
function is listed in the symbols files.