Remove unneeded, easy to remove goto labels (cleanup|error|done|...).
Signed-off-by: NDaniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: NErik Skultety <eskultet@redhat.com>

With NVMe disks, one can start a blockjob with a NVMe disk
that is not visible in domain XML (at least right away). Usually,
it's fairly easy to override this limitation of
qemuDomainGetMemLockLimitBytes() - for instance for hostdevs we
temporarily add the device to domain def, let the function
calculate the limit and then remove the device. But it's not so
easy with virStorageSourcePtr - in some cases they don't
necessarily are attached to a disk. And even if they are it's
done later in the process and frankly, I find it too complicated
to be able to use the simple trick we use with hostdevs.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NCole Robinson <crobinso@redhat.com>

At the very beginning of the attach function the
qemuDomainStorageSourceChainAccessAllow() is called which
modifies CGroups, locks and seclabels for new disk and its
backing chain. This must be followed by a counterpart which
reverts back all the changes if something goes wrong. This boils
down to calling qemuDomainStorageSourceChainAccessRevoke() which
is done under 'error' label. But not all failure branches jump
there. They just jump onto 'cleanup' label where no revoke is
done. Such mistake is easy to do because 'cleanup' label does
exist. Therefore, dissolve 'error' block in 'cleanup' and have
everything jump onto 'cleanup' label.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NCole Robinson <crobinso@redhat.com>

Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>
Signed-off-by: NDaniel P. Berrangé <berrange@redhat.com>

Our normal practice is for the object type to be the name prefix, and
the object instance be the first parameter passed in.

Rename these to virDomainObjSave and virDomainDefSave moving their
primary parameter to be the first one. Ensure that the xml options
are passed into both functions in prep for future work.

Finally enforce checking of the return type and mark all parameters
as non-NULL.
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>
Signed-off-by: NDaniel P. Berrangé <berrange@redhat.com>

This also isn't required (due to the vportprofile being stored in the
NetDef as a pointer rather than being directly contained), but it
seemed dishonest to not mark it as const (and thus permit users to
modify its contents)
Signed-off-by: NLaine Stump <laine@redhat.com>
Reviewed-by: NCole Robinson <crobinso@redhat.com>

In this case, the virNetDevBandwidthPtr that is returned is not to a
region within the virDomainNetDef arg, but points elsewhere (the
NetDef has the pointer, not the entire object), so technically it's
not necessary to make the return value a const, but it's a bit
disingenuous to *not* do it.
Signed-off-by: NLaine Stump <laine@redhat.com>
Reviewed-by: NCole Robinson <crobinso@redhat.com>

Signed-off-by: NDaniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Reviewed-by: NCole Robinson <crobinso@redhat.com>
Signed-off-by: NDaniel Henrique Barboza <danielhb413@gmail.com>

Reviewed-by: NCole Robinson <crobinso@redhat.com>
Signed-off-by: NDaniel Henrique Barboza <danielhb413@gmail.com>

The current 'setvcpus' timeout message requires a deeper
understanding of QEMU/Libvirt internals to proper react to it.
One who knows how setvcpus unplug work (it is an asynchronous
operation between QEMU and guest that Libvirt can't know for
sure if it failed, unless an explicit error happened during the
timeout period) will read the message and not assume a failed
operation. But the regular user, most often than not, will read
it and believe that the unplug operation failed.

This leads to situations where the user isn't exactly relieved
when accessing the guest and seeing that the unplug operation
worked. Instead, the user feel mislead by the timeout message
setvcpus threw.

Changing the timeout message to let the user know that the
unplug status is not known, and manual inspection in the guest
is required, is not a silver bullet. But it gives a more
realistic expectation of what happened, as best as we can tell
from Libvirt side anyways.
Reviewed-by: NCole Robinson <crobinso@redhat.com>
Signed-off-by: NDaniel Henrique Barboza <danielhb413@gmail.com>

qemu_hotplugpriv.h is a header file created to share a global variable
called 'qemuDomainRemoveDeviceWaitTime', declared in qemu_hotplug.c,
to other files that would want to change the timeout value
(currently, only tests/qemuhotplugtest.c).

Previous patch deprecated the variable, using qemu_driver->unplugTimeout
to set the timeout instead. This means that the header file is now
unused, and can be safely discarded.
Reviewed-by: NCole Robinson <crobinso@redhat.com>
Signed-off-by: NDaniel Henrique Barboza <danielhb413@gmail.com>

For some architectures and setups, device removal can take
longer than the default 5 seconds. This results in commands
such as 'virsh setvcpus' to fire timeout messages even if
the operation were successful in the guest, confusing the
user.

This patch sets a new 10 seconds unplug timeout for PPC64
guests. All other archs will keep the default 5 seconds
timeout.

Instead of putting 'if PPC64' conditionals inside qemu_hotplug.c
to set the new timeout value, a new function called
qemuDomainGetUnplugTimeout was added. The timeout value is then
retrieved when needed, by passing the correspondent DomainDef
object. This approach allows for different guest architectures
to have distint unplug timeout intervals, regardless of the
host architecture. This design also makes it easier to
modify/enhance the unplug timeout logic in the future
(allow for special timeouts for TCG domains, for example).

A new mock file was created to work with qemuhotplugtest.c,
given that the test timeout is significantly shorter than
the actual timeout value in qemu_hotplug.c.

The now unused 'qemuDomainRemoveDeviceWaitTime' global can't
be simply erased from qemu_hotplug.c though. Next patch will
remove it properly.
Reviewed-by: NCole Robinson <crobinso@redhat.com>
Suggested-by: NCole Robinson <crobinso@redhat.com>
Signed-off-by: NDaniel Henrique Barboza <danielhb413@gmail.com>

When attaching a mediated host device of model vfio-ccw without
specifying a guest-address, none is generated by libvirt. Let's fix this
and make sure to generate a device address during live-hotplug.
Reviewed-by: NBoris Fiuczynski <fiuczy@linux.ibm.com>
Signed-off-by: NBjoern Walk <bwalk@linux.ibm.com>
Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NJán Tomko <jtomko@redhat.com>

Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NDaniel Henrique Barboza <danielhb413@gmail.com>

Commit 01ca4010 (libvirt v5.1.0) moved address reservation for
hotplugged interface devices up to an earlier point in
qemuDomainAttachNetDevice(), because that function calls
qemuDomainSupportsNicdev() (in the case of
VIR_DOMAIN_NET_TYPE_VHOSTUSER), and qemuDomainSupportsNicdev() needs
to know the address type (for ARM machinetypes) and returns incorrect
results when the address type is "none".

This bugfix unfortunately caused a regression, because it also made PCI
address reservation happen before we noticed that the device was a
*hostdev* interface. Those interfaces are hotplugged by just calling
out to qemuDomainAttachHostdevDevice() - that function would then also
attempt to reserve the *same PCI address* that had just been reserved
in qemuDomainAttachNetDevice().

The solution is to move the bit of code that short-circuits out to
virDomainHostdevAttach() up *even earlier* so that no PCI address has
been allocated by the time it's called.

https://bugzilla.redhat.com/show_bug.cgi?id=1744523Signed-off-by: NLaine Stump <laine@redhat.com>
Reviewed-by: NAndrea Bolognani <abologna@redhat.com>

In both replaced cases we have other code that verifies that the bus
can't be changed or that the target is unique, so limiting the search to
disks with same bus makes no sense.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NDaniel Henrique Barboza <danielhb413@gmail.com>

In some places we need to check if a hostdev has VFIO backend.
Because of how complicated virDomainHostdevDef structure is, the
check consists of three lines. Move them to a function and
replace all checks with the function call.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NCole Robinson <crobinso@redhat.com>

Replace all occurrences of
  if (VIR_STRDUP(a, b) < 0)
     /* effectively dead code */
with:
  a = g_strdup(b);
Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Replace:
  if (!s && VIR_STRDUP(s, str) < 0)
    goto;
with:
  if (!s)
    s = g_strdup(str);
Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Now that all the types using VIR_AUTOUNREF have a cleanup func defined
to virObjectUnref, use g_autoptr instead of VIR_AUTOUNREF.
Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Since commit 44e7f029
    util: rewrite auto cleanup macros to use glib's equivalent

VIR_AUTOPTR aliases to g_autoptr. Replace all of its use by the GLib
macro version.
Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Since commit 44e7f029
    util: rewrite auto cleanup macros to use glib's equivalent

VIR_AUTOFREE is just an alias for g_autofree. Use the GLib macros
directly instead of our custom aliases.
Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Also define the macro for building with GLib older than 2.60
Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Use G_GNUC_UNUSED from GLib instead of ATTRIBUTE_UNUSED.
Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Cleanup labels are also dropped where possible.
Signed-off-by: NDaniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: NErik Skultety <eskultet@redhat.com>

The fact that qemu is capable -netdev socket is not enough to
start a migratable domain. It also needs dbus-vmstate capability.
Since there are already some qemu releases which have
net-socket-dgram capability and don't have dbus-vmstate we need
to check for dbus-vmstate.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NJán Tomko <jtomko@redhat.com>

Signed-off-by: NJán Tomko <jtomko@redhat.com>
Reviewed-by: NCole Robinson <crobinso@redhat.com>

qemuDomainAttachNetDevice() (hotplug) previously had some of the
validation that is in qemuDomainValidateActualNetDef(), but it was
incomplete. qemuDomainChangeNet() had none of that validation, but it
is all appropriate in both cases.

This is the final piece of a previously partial resolution to
https://bugzilla.redhat.com/1502754Signed-off-by: NLaine Stump <laine@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

This fixes bug in

  commit bbe2aa62
  Author: Daniel P. Berrangé <berrange@redhat.com>
  Date:   Thu Jul 26 17:24:30 2018 +0100

    conf: simplify link from hostdev back to network device

    hostdevs have a link back to the original network device. This is fairly
    generic accepting any type of device, however, we don't intend to make
    use of this approach in future. It can thus be specialized to network
    devices.
Reviewed-by: NCole Robinson <crobinso@redhat.com>
Signed-off-by: NDaniel P. Berrangé <berrange@redhat.com>

which mistakenly deleted the assignment to the 'net' variable,
which meant we never invoked the network driver release callback
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>
Signed-off-by: NDaniel P. Berrangé <berrange@redhat.com>

When starting a domain, we use the presence of a vfio-pci or
mdev hostdev to determine if the memlock maximum needs to be
increased.  But if we hotplug either of these devices, only the
vfio-pci path gets that love.  This means that attaching a, say,
vfio-ccw device will appear to succeed but the device may be
unusable as the guest may see I/O errors on long CCW chains.
The host, meanwhile, would be flooded with these messages:

  vfio_pin_page_external: Task qemu-system-s39 (11584) RLIMIT_MEMLOCK (65536) exceeded

Let's adjust the maximum memlock value in the mdev hotplug path,
so that the domain has the same value as if it were started with
one or more mdev devices in its configuration.
Signed-off-by: NEric Farman <farman@linux.ibm.com>
Reviewed-by: NDaniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: NPavel Hrdina <phrdina@redhat.com>

If attaching a PCI hostdev fails, there are several things that
need to be un-done as part of the cleanup.  One thing that is
not done is re-calculating/re-setting the maximum amount of locked
memory for the domain, since we may have changed that.

Let's fix that, just to ensure everything is back the way it was.
Signed-off-by: NEric Farman <farman@linux.ibm.com>
Reviewed-by: NDaniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: NPavel Hrdina <phrdina@redhat.com>

Let's pull this hunk out into a function, so it can be reused
in another codepath that needs to do the same thing.
Signed-off-by: NEric Farman <farman@linux.ibm.com>
Reviewed-by: NDaniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: NPavel Hrdina <phrdina@redhat.com>

Signed-off-by: NMarc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

If a slirp-helper is associated with a network interface (after
probing & preparing succesfully), pass the socket fd to QEMU and use
"-net socket,fd=".
Signed-off-by: NMarc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Add dbusVMStates to keep a list of dbus-vmstate objects needed for
migration. They are populated on the command line during start or
qemuDBusVMStateAdd/Remove() will hotplug them as needed.
Signed-off-by: NMarc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

With blockdev we must issue the block_set_io_throttle QMP command to
setup disk throttling as we currently can't do it with the 'throttle'
layer.

Unfortunately there's nothing we can do if it fails.

https://bugzilla.redhat.com/show_bug.cgi?id=1733163Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NJán Tomko <jtomko@redhat.com>

Get rid of the last manually freed var.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NJán Tomko <jtomko@redhat.com>

Switch to using VIR_AUTOFREE and remove the cleanup label.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NJán Tomko <jtomko@redhat.com>