When enabling the router in the device we will represent L3 netdevs
using router interfaces (RIFs). These will be specified whenever
programming routes or neighbours on the netdev.

Introduce the basic RIF infrastructure which allows one to lookup a RIF
by its netdev. Later patches in the series will extend this, but the
basic routines are needed now in order to direct traffic to CPU.

Pointers to the RIF structs are stored in an array indexed by the RIF's
number. This will allow us to efficiently update the kernel's neighbour
table when regularly dumping the device's table.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a skeleton router file and do basic HW initialization of router.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During ports initialization a net device is registered for each
available port, which implies the port is usable. However, a port is
only usable after the different parts of the device (e.g. flooding,
buffers) are initialized. This is especially important now, when we must
initialize the router before the ports, as otherwise the device can't be
initialized.

Solve that by initializing the switch ports at the end of init sequence.

Also, remove an unnecessary warning about port up/down events, which
would otherwise be invoked whenever removing the driver, as ports are
removed before unregistering the listener for these events.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the Router General Configuration Register (RGCR), which allows us to
enable the router in the device and configure its various parameters.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are going to assign router interfaces (RIFs) to netdevs if an IPv4
address was assigned to them. If one was assigned to a port netdev, this
will translate to the PVID vPort being member in a RIF.

While it's possible for a LAG slave to have an IP address, we can't have
a vPort being member in two FIDs (assuming the LAG device will be
put in bridge / assigned an IP address).

Solve that by making the PVID vPort leave any FID it might be a member
in when joining / leaving LAG.

Note that the PVID vPort is the only vPort that can be present on the
port when it's put under LAG.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When VLAN devices are created on top of LAG, their underlying vPorts are
configured correctly with LAG membership.

However, the PVID vPort is implicit and already present when the port
netdev is put under LAG, so its LAG membership is never set. Set it
correctly when joining / leaving LAG.

This didn't matter until now, but we are going to introduce support for
router interfaces (RIFs), which need to take into account LAG membership.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When port isn't bridged it is still possible to invoke switchdev ops and
configure the device's VLAN filters.

However, this will require us to use different Router InterFaces (RIFs)
for the same netdev, instead of one per-netdev as with any other
configuration.

Taking the above into account and the fact that this functionality is
questionable with regards to the device's normal use-case, remove it and
instead return an error.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port netdevs (e.g. swXpY) that are not bridged are represented in the
device using a vPort with VID=PVID=1 (the PVID vPort), as untagged
packets entering the switch are internally tagged with the PVID VLAN.
When these packets are routed through a different port netdev they
should egress untagged.

This wasn't a problem until now, as non-bridged traffic only originated
from the CPU, which transmits packets out of the port as-is.

When a vPort is created with VID 1 mark it as egress untagged.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en updates for net-next.

Mostly small miscellaneous changes.

Please review for net-next.  Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The allowable range is 0.25 seconds to 1 second interval.  Default is
1 second.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is useful for multi-function devices.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With a default VLAN, the VF has its own VLAN domain and it can receive
all traffic within that domain.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For correctness, the MRU enables bit must be set when passing the
MRU to firmware during vnic configuration.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to the Ethtool FLASHDEV command handler for additional
firmware types to cover all the on-chip processors.
Signed-off-by: NRob Swindell <rob.swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon successful mgmt processor firmware update, request a self
reset upon next PCIe reset (e.g. system reboot).
Signed-off-by: NRob Swindell <rob.swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support Secure Firmware Update, we must be able to allocate
a staging area in the Flash.  This patch adds support for the
"update" type to tell firmware to do that.
Signed-off-by: NRob Swindell <rob.swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling the firmware to do function reset on the PF will kill all the VFs.
To prevent that, we call function reset on the 1st PF open before any VF
can be activated.  On subsequent PF opens (with possibly some active VFs),
a bit has been set and we'll skip the function reset.  VF driver will
always do function reset on every open.  If there is an AER event, we will
always do function reset.
Signed-off-by: NMichael Chan <michael.chan@broadocm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And update driver version to 1.3.0.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Returning 0 for doing nothing is confusing to the user.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G SRIOV E-Switch offload and VF representors

We are happy to announce SRIOV E-Switch offload and VF netdev representors.

Or Gerlitz says:

Currently, the way SR-IOV embedded switches are dealt with in Linux is limited
in its expressiveness and flexibility, but this is not necessarily due to
hardware limitations. The kernel software model for controlling the SR-IOV
switch simply does not allow the configuration of anything more complex than
MAC/VLAN based forwarding.

Hence the benefits brought by SRIOV come at a price of management flexibility,
when compared to software virtual switches which are used in Para-Virtual (PV)
schemes and allow implementing complex policies and virtual topologies. Such
SW switching typically involved a complex per-packet processing within the host
kernel using subsystems such as TC, Bridge, Netfilter and Open-vswitch.

We'd like to change that and get the best of both worlds: the performance of SR-IOV
with the management flexibility of software switches. This will eventually include
a richer model for controlling the SR-IOV switch for flow-based switching and
tunneling. Under this model, the e-switch is configured dynamically and a fallback
to software exists in case the hardware is unable to offload all required flows.

This series from Hadar Hen-Zion and myself, is the 1st step in that direction,
specfically, it provides full control on the SRIOV embedded switching by host
software and paves the way to offload switching rules and polices with downstream
patches.

To allow for host based SW control on the SRIOV HW switch, we introduce per VF
representor host netdevice. The VF representor plays the same role as TAP devices
in PV setup. A packet send through the VF representor on the host arrives to
the VF, and a packet sent through the VF is received by its representor. The
administrator can hook the representor netdev into a kernel switching component.
Once they do that, packets from the VF are subject to steering (matching and
actions) of that software component."

Doing so indeed hurts the performance benefits of SRIOV as it forces all the
traffic to go through the hypervisor. However, this SW representation is what
would eventually allow us to introduce hybrid model, where we offload steering
for some of the VF/VM traffic to the HW while keeping other VM traffic to go
through the hypervisor. Examples for the latter are first packet of flows which
are needed for SW switches learning and/or matching against policy database or
types of traffic for which offloading is not desired or not supported by the
current HW eswitch generation.

The embedded switch is managed through a PCI device driver. As such, we introduce
a devlink/pci based scheme for setting the mode of the e-switch. The current mode
(where steering is done based on mac/vlan, etc) is referred to as "legacy" and the
new mode as "offloads".

For the mlx5 driver / ConnectX4 HW case, the VF representors implement a functional
subset of mlx5e Ethernet netdevices using their own profile. This design buys us robust
implementation with code reuse and sharing.

The representors are created by the host PCI driver when (1) in SRIOV and (2) the
e-switch is set to offloads mode. Currently, in mlx5 the e-switch management is done
through the PF vport (0) and hence the VF representors along with the existing PF
netdev which represents the uplink share the PCI PF device instance.

The series is built from two major components, the first relates to the e-switch
management and the second to VF representors.

We start with a refactoring that treats the existing SRIOV e-switch code as of operating
in legacy mode. Next, we add the code for the offloads mode which programs the e-switch
to operate in a way which serves for software based switching:

1. miss rule which matches all packets that do not match any HW other switching rule
and forwards them to the e-switch management port (0) for further processing.

2. infrastructure for send-to-vport rules which conceptually bypass other "normal"
steering rules which present at the e-switch datapath. Such rules apply only for packets
that originate in the e-switch manager vport (0).

Since all the VF reps run over the same e-switch port, we use more logic in the host PCI
driver to do HW steering of missed packets into the HW queue opened by a the respective VF
representor. Finally here, we add the devlink APIs to configure the e-switch mode.

The second part from Hadar starts with some refactoring work which allow for multiple
mlx5e NIC instances to be created over the same PCI function, use common resources
and avoid wrong loopbacks.

Next comes the heart of the change which is a profile definition which allow to practically
have both "conventional" mlx5e NIC use cases such as native mode (non SRIOV), VF, PF and VF
representor to share the Ethernet driver code. This is done by a small surgery that ended up
with few internal callbacks that should be implemented by a profile instance. The profile
for the conventional NIC is implemented, to preserve the existing functionality.

The last two patches add e-switch registration API for the VF representors and the
implementation of the VF representors netdevice profile. Being an mlx5e instance, the
VF representor uses HW send/recv queues, completions queues and such. It currently doesn't
support NIC offloads but some of them could be added later on. The VF representor has
switchdev ops, where currently the only supported API is the one to the HW ID,
which is needed to identify multiple representors belonging to the same e-switch.

The architecture + solution (software and firmware) work were done by a team consisting
of Ilya Lesokhin, Haggai Eran, Rony Efraim, Tal Anker, Natan Oppenheimer, Saeed Mahameed,
Hadar and Or, thanks you all!

v1 --> v2 fixes:
* removed unneeded variable (patch #3)
* removed unused value DEVLINK_ESWITCH_MODE_NONE (patch #8)
* changed the devlink mode name from "offloads" to "switchdev" which
   better describes what are we referring here, using a known concept (patch #8)
* correctly refer to devlink e-switch modes (patch #10)
* use the correct mlx5e way to define the VF rep statistics  (patch #16)

v2 --> v3 fixes:
* Rebased on top 6fde0e63 'be2net: signedness bug in be_msix_enable()'
* Handled compilation error introduced by rebase on top "f5074d0c Merge branch 'mlx5-100G-fixes'"
* This series applies perfectly even with 'mlx5 resiliency and xmit path fixes' merged to net-next
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the relevant profile functions to create mlx5e driver instance
serving as VF representor. When SRIOV offloads mode is enabled, each VF
will have a representor netdevice instance on the host.

To do that, we also export set of shared service functions from en_main.c,
such that they can be used by both NIC and repsresentors netdevs.

The newly created representor netdevice has a basic set of net_device_ops
which are the same ndo functions as the NIC netdevice and an ndo of it's
own for phys port name.

The profiling infrastructure allow sharing code between the NIC and the
vport representor even though the representor has only a subset of the
NIC functionality.

The VF reps and the PF which is used in that mode to represent the uplink,
expose switchdev ops. Currently the only op supposed is attr get for the
port parent ID which here serves to identify net-devices belonging to the
same HW E-Switch. Other than that, no offloading is implemented and hence
switching functionality is achieved if one sets SW switching rules, e.g
using tc, bridge or ovs.

Port phys name (ndo_get_phys_port_name) is implemented to allow exporting
to user-space the VF vport number and along with the switchdev port parent
id (phys_switch_id) enable a udev base consistent naming scheme:

SUBSYSTEM=="net", ACTION=="add", ATTR{phys_switch_id}=="<phys_switch_id>", \
        ATTR{phys_port_name}!="", NAME="$PF_NIC$attr{phys_port_name}"

where phys_switch_id is exposed by the PF (and VF reps) and $PF_NIC is
the name of the PF netdevice.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce E-Switch registration/unregister representors functions.

Those functions are called by the mlx5e driver when the PF NIC is
created upon pci probe action regardless of the E-Switch mode (NONE,
LEGACY or OFFLOADS).

Adding basic E-Switch database that will hold the vport represntors
upon creation.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow support in representor netdevices where we create more than one
netdevice per NIC, add profiles to the mlx5e driver. The profiling
allows for creation of mlx5e instances with different characteristics.

Each profile implements its own behavior using set of function pointers
defined in struct mlx5e_profile. This is done to allow for avoiding complex
per profix branching in the code.

Currently only the profile for the conventional NIC is implemented,
which is of use when a netdev is created upon pci probe.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current driver implementation two types of receive queue
tables (RQTs) are in use - direct and indirect.

Change the driver to mark each new created RQT (direct or indirect)
as "enabled". This behaviour is needed for introducing new mlx5e
instances which serve to represent SRIOV VFs.

The VF representors will have only one type of RQTs (direct).

An "enabled" flag is added to each RQT to allow better handling
and code sharing between the representors and the nic netdevices.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current refresh tirs self loopback mechanism, refreshes all the tirs
belonging to the same mlx5e instance to prevent self loopback by packets
sent over any ring of that instance. This mechanism relies on all the
tirs/tises of an instance to be created with the same transport domain
number (tdn).

Change the driver to refresh all the tirs created under the same tdn
regardless of which mlx5e netdev instance they belong to.

This behaviour is needed for introducing new mlx5e instances which serve
to represent SRIOV VFs. The representors and the PF share vport used for
E-Switch management, and we want to avoid NIC level HW loopback between
them, e.g when sending broadcast packets. To achieve that, both the
representors and the PF NIC will share the tdn.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow creating more than one netdev over the same PCI function, we
change the driver such that global NIC resources are created once and
later be shared amongst all the mlx5e netdevs running over that port.

Move the CQ UAR, PD (pdn), Transport Domain (tdn), MKey resources from
being kept in the mlx5e priv part to a new resources structure
(mlx5e_resources) placed under the mlx5_core device.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement handlers for the devlink commands to get and set the SRIOV
E-Switch mode.

When turning to the switchdev/offloads mode, we disable the e-switch
and enable it again in the new mode, create the NIC offloads table
and create VF reps.

When turning to legacy mode, we remove the VF reps and the offloads
table, and re-initiate the e-switch in it's legacy mode.

The actual creation/removal of the VF reps is done in downstream patches.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The devlink interface is initially used to set/get the mode of the SRIOV e-switch.

Currently, these are only stubs for get/set, down-stream patch will actually
fill them out.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the commands to set and show the mode of SRIOV E-Switch, two modes
are supported:

* legacy: operating in the "old" L2 based mode (DMAC --> VF vport)

* switchdev: the E-Switch is referred to as whitebox switch configured
using standard tools such as tc, bridge, openvswitch etc. To allow
working with the tools, for each VF, a VF representor netdevice is
created by the E-Switch manager vendor device driver instance (e.g PF).
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the API to create vport rx rules of the form

	packet meta-data :: vport == $VPORT --> $TIR

where the TIR is opened by this VF representor.

This logic will by used for packets that didn't match any rule in the
e-switch datapath and should be received into the host OS through the
netdevice that represents the VF they were sent from.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Belongs to the NIC offloads name-space, and to be used as part of the
SRIOV offloads logic to steer packets that hit the e-switch miss rule
to the TIR of the relevant VF representor.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new namespace (MLX5_FLOW_NAMESPACE_OFFLOADS) to be populated
with flow steering rules that deal with rules that have have to
be executed before the EN NIC steering rules are matched.

The namespace is located after the bypass name-space and before the
kernel name-space. Therefore, it precedes the HW processing done for
rules set for the kernel NIC name-space.

Under SRIOV, it would allow us to match on e-switch missed packet
and forward them to the relevant VF representor TIR.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the API to create send-to-vport e-switch rules of the form

 packet meta-data :: send-queue-number == $SQN and source-vport == 0 --> $VPORT

These rules are to be used for a send-to-vport logic which conceptually bypasses
the "normal" steering rules currently present at the e-switch datapath.

Such rule should apply only for packets that originate in the e-switch manager
vport (0) and are sent for a given SQN which is used by a given VF representor
device, and hence the matching logic.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the sriov offloads mode, packets that are not matched by any other
rule should be sent towards the e-switch manager for further processing.

Add such "miss" rule which matches ANY packet as the last rule in the
e-switch FDB and programs the HW to send the packet to vport 0 where
the e-switch manager runs.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike the legacy mode, here, forwarding rules are not learned by the
driver per events on macs set by VFs/VMs into their vports, but rather
should be programmed by higher-level SW entities.

Saying that, still, in the offloads mode (SRIOV_OFFLOADS), two flow
groups are created by the driver for management (slow path) purposes:

The first group will be used for sending packets over e-switch vports
from the host OS where the e-switch management code runs, to be
received by VFs.

The second group will be used by a miss rule which forwards packets toward
the e-switch manager. Further logic will trap these packets such that
the receiving net-device as seen by the networking stack is the representor
of the vport that sent the packet over the e-switch data-path.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define three modes for the SRIOV e-switch operation, none (SRIOV_NONE,
none of the VF vports are enabled), legacy (SRIOV_LEGACY, the current mode)
and sriov offloads (SRIOV_OFFLOADS). Currently, when in SRIOV, only the
legacy mode is supported, where steering rules are of the form:

        destination mac --> VF vport

This patch does not change any functionality.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature patchset includes the following changes:

 - two patches with minimal clean up work by Antonio Quartulli and
   Simon Wunderlich

 - eight patches of B.A.T.M.A.N. V, API and documentation clean
   up work, by Antonio Quartulli and Marek Lindner

 - Andrew Lunn fixed the skb priority adoption when forwarding
   fragmented packets (two patches)

 - Multicast optimization support is now enabled for bridges which
   comes with some protocol updates, by Linus Luessing
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>