On detection of an EEH error, some Power4 systems seem to occasionally
want to be reset twice before they report themselves as fully recovered.
This patch re-arranges the code to attempt additional resets if the first
one doesn't take.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Noticed that the U3_*CFA macros have some typos:

#define U3_HT_CFA0(devfn, off)		\
		((((unsigned long)devfn) << 8) | offset)

(refers to offset rather than off)

#define U3_AGP_CFA0(devfn, off)	\
	((1 << (unsigned long)PCI_SLOT(dev_fn)) \
	| (((unsigned long)PCI_FUNC(dev_fn)) << 8) \

(refers to dev_fn rather than devfn)

Things happen to work, but there doesn't seem to be any reason these
shouldn't be functions.  Overall behavior should be unchanged.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When there is a PCI-X mode 2 capable device behind the HT<->PCI-X
bridge, the pci core decides that the device has the extended 4K
config space, even though the bus is not operating in mode 2.  This is
because the u3_ht pci ops silently accept offsets greater than 255 but
use only the 8 least significant bits, which means reading at offset
0x100 gets the data at offset 0x0, and causes confusion for lspci.

Reject accesses to configuration space offsets greater than 255.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch changes the io operations so that they are out of line if
CONFIG_PPC_ISERIES is set and includes a firmware feature check in
that case.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Update to the PowerPC PCI error recovery code.

Add code to enable MMIO if a device driver reports that it is capable
of recovering on its own.  One anticipated use of this having a device
driver enable MMIO so that it can take a register dump, which might
then be followed by the device driver requesting a full reset.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add wrapper around the rtas call to enable MMIO or DMA on a frozen pci
slot.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Clean up subroutine documentation; mostly formatting changes, with
some new content.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This corrects a pci_dev get/put imbalance that can occur only in
highly unlikely situations (kmalloc failures, pci devices with
overlapping resource addresses).  No actual failures seen, this was
spotted during code review.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Left over from the constifying of get_property.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Add instrumentation for hypervisor calls on pseries.  Call statistics
include number of calls, wall time and cpu cycles (if available) and
are made available via debugfs.  Instrumentation code is behind the
HCALL_STATS config option and has no impact if not enabled.
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Base patch for PA6T and PA6T-1682M. This introduces the
arch/powerpc/platform/pasemi directory, together with basic
implementations for various setup.

Much of this was based on other platform code, i.e. Maple, etc.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

As part of the new irq code pseries_kexec_cpu_down() was split into a
xics and mpic version. The vpa unregister logic is now only done in the
xics routine, and although that's ok in practice (we don't have SPLPAR
machines with mpic), I'd rather have the two concepts stay separate.

So move the vpa unregister into pseries_kexec_cpu_down(), which gets called
by both the xics and mpic routines. This also gives us an obvious place to
put any new kexec-down logic needed in future.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Ben speaks; we follow.
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

New sparse caught that typo which could have caused erratic hardware
behaviour on some machines if the platform functions are used by the
firmware to change bits in some FCR registers.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The port to genirq & the new powerpc interrupt model in 2.6.18 introduced a
bug in the legacy PowerMac PIC code (used on older machines) because of a
typo potentially causing hangs due to interrupt storms.  This fixes it,
along with a performance issue causing us to do spurrious retriggers after
masking an interrupt.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This adds a new hardware information table for mpic. This enables
the mpic code to deal with mpic controllers with different register
layouts and hardware behaviours.

This introduces CONFIG_MPIC_WEIRD.  For boards with non standard mpic
controllers, select CONFIG_MPIC_WEIRD and add its hardware information
in the mpic_infos[] array.

TSI108/109 PIC takes the first index of weird hardware information
table.  :)  The table can be extended. The Tsi108/109 PIC looks like
standard OpenPIC but, in fact, is different in register mapping and
behavior.

The patch does not affect the behavior of standard mpic.  If
CONFIG_MPIC_WEIRD is not defined, the code is essentially identical to
the current code.

[benh@kernel.crashing.org:
This patch is a slightly cleaned up version of Zang Roy's support for
the TSI108 MPIC variant. It also fixes up MPC7448_hpc2 to use the new
version of the type macros and changes the way MPIC is selected in
Kconfig to better match what is done for other system devices.
]
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes MPC834x MDS (formerly SYS) and ITX platform code to get IRQ data (including PCI) from the device tree, and to use the new IPIC code.

renamed defconfig (sys -> mds), left one redundant NULL assignment in mpc83xx_pcibios_fixup to keep the compiler happy.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

After going through the trouble of setting up the PIC base
address in the pic@40000 device tree node, use it instead
of the obsolete hard-coded value.
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

gcc 4.1 produces some warnings that say it is ignoring the packed
attribute on some structure elements, so, since all the elements of
these structs are packed, pack the structs instead.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Just one bit of fallout from the constification of the get_property
return value.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The rtas console doesn't have to be Cell specific.  If we get both
RTAS tokens, we should just enabled the console then and there.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Cleanup CPU inits a bit more, Geoff Levand already did some earlier.

* Move CPU state save to cpu_setup, since cpu_setup is only ever done
  on cpu 0 on 64-bit and save is never done more than once.
* Rename __restore_cpu_setup to __restore_cpu_ppc970 and add
  function pointers to the cputable to use instead. Powermac always
  has 970 so no need to check there.
* Rename __970_cpu_preinit to __cpu_preinit_ppc970 and check PVR before
  calling it instead of in it, it's too early to use cputable.
* Rename pSeries_secondary_smp_init to generic_secondary_smp_init since
  everyone but powermac and iSeries use it.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Whitespace clean up for cell/interrupt.c.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The patch rewrites mpc7448hpc2 board irq support according to the new
mpic device tree interface.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The bootx_init.c trampoline didn't properly add the ramdisk to the
"reserve map" (list of reserved areas of memory), thus causing all sorts
of failures when using BootX with an initrd. Also fixes a possible
problem if the ramdisk is located before the device-tree passed by
BootX.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

IRQ setup now comes from the Flat Device Tree and use the new generic
IRQ code.  Fixed the fsl_soc.c IRQ OF interrupt node parsing.
Removed some unused MPC86xx macro definition.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
(cherry picked from 919fede6 commit)

* Fix IRQ support in the 85xx CDS boards so it uses the new
  generic stuff
* Fix PCI IRQ mapping to use the device tree
* Disabled i8259 support to allow the CDS to boot.  This will be
  fixed soon, but the current code doesn't even compile, so this
  is a vast improvement
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

* Fixed 8540 ADS support for the new irq layer
* Fixed 8540 ADS support for mapping PCI interrupts
* Updated 8540 ADS to use device tree for interrupt assignment
  and sense values
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds a shadow buffer for the SLBs and regsiters it with PHYP.
Only the bolted SLB entries (top 3) are shadowed.

The SLB shadow buffer tells the hypervisor what the kernel needs to
have in the SLB for the kernel to be able to function.  The hypervisor
can use this information to speed up partition context switches.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

IRQ setup now comes from the Flat Device Tree and use the new generic
IRQ code.  Fixed the fsl_soc.c IRQ OF interrupt node parsing.
Removed some unused MPC86xx macro definition.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Noticing the following might_sleep warning (dump_stack()) during kdump
testing when CONFIG_DEBUG_SPINLOCK_SLEEP is enabled. All secondary CPUs
will be calling rtas_set_indicator with interrupts disabled to remove
them from global interrupt queue.

BUG: sleeping function called from invalid context at
arch/powerpc/kernel/rtas.c:463
in_atomic():1, irqs_disabled():1
Call Trace:
[C00000000FFFB970] [C000000000010234] .show_stack+0x68/0x1b0 (unreliable)
[C00000000FFFBA10] [C000000000059354] .__might_sleep+0xd8/0xf4
[C00000000FFFBA90] [C00000000001D1BC] .rtas_busy_delay+0x20/0x5c
[C00000000FFFBB20] [C00000000001D8A8] .rtas_set_indicator+0x6c/0xcc
[C00000000FFFBBC0] [C000000000048BF4] .xics_teardown_cpu+0x118/0x134
[C00000000FFFBC40] [C00000000004539C]
.pseries_kexec_cpu_down_xics+0x74/0x8c
[C00000000FFFBCC0] [C00000000002DF08] .crash_ipi_callback+0x15c/0x188
[C00000000FFFBD50] [C0000000000296EC] .smp_message_recv+0x84/0xdc
[C00000000FFFBDC0] [C000000000048E08] .xics_ipi_dispatch+0xf0/0x130
[C00000000FFFBE50] [C00000000009EF10] .handle_IRQ_event+0x7c/0xf8
[C00000000FFFBF00] [C0000000000A0A14] .handle_percpu_irq+0x90/0x10c
[C00000000FFFBF90] [C00000000002659C] .call_handle_irq+0x1c/0x2c
[C00000000058B9C0] [C00000000000CA10] .do_IRQ+0xf4/0x1a4
[C00000000058BA50] [C0000000000044EC] hardware_interrupt_entry+0xc/0x10
 --- Exception: 501 at .plpar_hcall_norets+0x14/0x1c
   LR = .pseries_dedicated_idle_sleep+0x190/0x1d4
[C00000000058BD40] [C00000000058BDE0] 0xc00000000058bde0 (unreliable)
[C00000000058BDF0] [C00000000001270C] .cpu_idle+0x10c/0x1e0
[C00000000058BE70] [C000000000009274] .rest_init+0x44/0x5c

To fix this issue, rtas_set_indicator_fast() is added so that will not
wait for RTAS 'busy' delay and this new function is used for kdump (in
xics_teardown_cpu()) and for CPU hotplug ( xics_migrate_irqs_away() and
xics_setup_cpu()).

Note that the platform architecture spec says that set-indicator
on the indicator we're using here is not permitted to return the
busy or extended busy status codes.
Signed-off-by: NHaren Myneni <haren@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We should not be calling power4_enable_pmcs() in
pseries_lpar_enable_pmcs(); just doing the hypercall is sufficient.
Prior to 2.6.15 we did not call power4_enable_pmcs() for an lpar.

power4_enable_pmcs() tries to read the hid0 register which is no
longer legal for an lpar in newer Power processors.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Our pseries hcall interfaces are out of control:

	plpar_hcall_norets
	plpar_hcall
	plpar_hcall_8arg_2ret
	plpar_hcall_4out
	plpar_hcall_7arg_7ret
	plpar_hcall_9arg_9ret

Create 3 interfaces to cover all cases:

	plpar_hcall_norets:	7 arguments no returns
	plpar_hcall:		6 arguments 4 returns
	plpar_hcall9:		9 arguments 9 returns

There are only 2 cases in the kernel that need plpar_hcall9, hopefully
we can keep it that way.

Pass in a buffer to stash return parameters so we avoid the &dummy1,
&dummy2 madness.
Signed-off-by: NAnton Blanchard <anton@samba.org>
--
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch fixes several problems:
- The legacy backlight value might be set at interrupt time. Introduced
  a worker to prevent it from directly calling the backlight code.
- via-pmu allows the backlight to be grabbed, in which case we need to
  prevent other kernel code from changing the brightness.
- Don't send PMU requests in via-pmu-backlight when the machine is about
  to sleep or waking up.
- More Kconfig fixes.
Signed-off-by: NMichael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

powermac platform & macintosh driver changes.

Built for pmac32_defconfig, g5_defconfig
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

maple platform changes.

Built for maple_defconfig
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

chrp platform changes.

Built for chrp32_defconfig
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

cell platform changes.

Built for cell_defconfig
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>