On detection of an EEH error, some Power4 systems seem to occasionally
want to be reset twice before they report themselves as fully recovered.
This patch re-arranges the code to attempt additional resets if the first
one doesn't take.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch causes fsl_soc.h to import the definition of phys_addr_t
itself, rather than relying on its includer to do so.
Signed-off-by: NScott Wood <scott@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Noticed that the U3_*CFA macros have some typos:

#define U3_HT_CFA0(devfn, off)		\
		((((unsigned long)devfn) << 8) | offset)

(refers to offset rather than off)

#define U3_AGP_CFA0(devfn, off)	\
	((1 << (unsigned long)PCI_SLOT(dev_fn)) \
	| (((unsigned long)PCI_FUNC(dev_fn)) << 8) \

(refers to dev_fn rather than devfn)

Things happen to work, but there doesn't seem to be any reason these
shouldn't be functions.  Overall behavior should be unchanged.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When there is a PCI-X mode 2 capable device behind the HT<->PCI-X
bridge, the pci core decides that the device has the extended 4K
config space, even though the bus is not operating in mode 2.  This is
because the u3_ht pci ops silently accept offsets greater than 255 but
use only the 8 least significant bits, which means reading at offset
0x100 gets the data at offset 0x0, and causes confusion for lspci.

Reject accesses to configuration space offsets greater than 255.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch fixes the assignment of pending registers to IRQ numbers for
the IPIC; the code previously assigned all IRQs to the high pending word
regardless of which word the interrupt belonged to.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch changes the io operations so that they are out of line if
CONFIG_PPC_ISERIES is set and includes a firmware feature check in
that case.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Update to the PowerPC PCI error recovery code.

Add code to enable MMIO if a device driver reports that it is capable
of recovering on its own.  One anticipated use of this having a device
driver enable MMIO so that it can take a register dump, which might
then be followed by the device driver requesting a full reset.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add wrapper around the rtas call to enable MMIO or DMA on a frozen pci
slot.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Clean up subroutine documentation; mostly formatting changes, with
some new content.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This corrects a pci_dev get/put imbalance that can occur only in
highly unlikely situations (kmalloc failures, pci devices with
overlapping resource addresses).  No actual failures seen, this was
spotted during code review.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Jakub noticed the cputable.c entry for Xilinx Virtex-4 FX was missing
a .platform value, so the AT_PLATFORM value wouldn't be set correctly.
This adds it.
Signed-off-by: NPeter Bergner <bergner@vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This abstracts the operations used in the bootwrapper, and defines
the operations needed for the bootwrapper to run on an OF platform.

The operations have been divided up into platform ops (platform_ops),
firmware ops (fw_ops), device tree ops (dt_ops), and console ops
(console_ops).

The proper operations will be hooked up at runtime to provide the
functionality that you need.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There are various places where we want to extract an unsigned long
value from a device-tree property that can be 1 or 2 cells in length.
This replaces some open-coded calculations, and one place where we
assumed without checking that properties were the length we wanted,
with a little of_read_ulong() helper.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This produces essentially the same code and will make the iSeries i/o
consolidation easier.

The count parameter is changed to long since that will produce the same
(better) code on 32 and 64 bit builds.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

_insw, _outsw, _insl amd _outsl are all unused, so remove them.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Left over from the constifying of get_property.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

If we build a pSeries/iSeries combined kernel, we will need this.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Fix MPC8349EMDS dts PCI interrupt-map values for IDSEL 0x18 per
Tanya's catch.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NTanya Jiang <tanya.jiang@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes a compile error that only surfaces on CONFIG_SMP=n builds;
<asm/hvcall.h> seems to get pulled in through another header file for
SMP builds.  This problem was introduced by the hvcall stats patch.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It seems that the occasional data corruption observed with the tg3
driver wasn't due to missing barriers after all, but rather seems to
be due to the DART (= IOMMU) in the U4 northbridge reading stale
IOMMU table entries from memory due to a race.  This fixes it by
making the CPU read the entry back from memory before using it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This changes the writeX family of functions to have a sync instruction
before the MMIO store rather than after, because the generally expected
behaviour is that the device receiving the MMIO store can be guaranteed
to see the effects of any preceding writes to normal memory.

To preserve ordering between writeX and readX, and to preserve ordering
between preceding stores and the readX, the readX family of functions
have had an sync added before the load.

Although writeX followed by spin_unlock is not officially guaranteed
to keep the writeX inside the spin-locked region unless an mmiowb()
is used, there are currently drivers that depend on the previous
behaviour on powerpc, which was that the mmiowb wasn't actually required.
Therefore we have a per-cpu flag that is set by writeX, cleared by
__raw_spin_lock and mmiowb, and tested by __raw_spin_unlock.  If it is
set, __raw_spin_unlock does a sync and clears it.

This changes both 32-bit and 64-bit readX/writeX.  32-bit already has a
sync in __raw_spin_unlock (since lwsync doesn't exist on 32-bit), and thus
doesn't need the per-cpu flag.

Tested on G5 (PPC970) and POWER5.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Export copy_4K_page() for use by modules via copy_page() (such as
CacheFiles).
Signed-Off-By: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

xmon does not print a backtrace per default. This is bad on systems with
USB keyboard, the most needed info about the crash is lost.
print a backtrace during the very first xmon entry.

Booting with xmon=nobt disables the autobacktrace functionality.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add instrumentation for hypervisor calls on pseries.  Call statistics
include number of calls, wall time and cpu cycles (if available) and
are made available via debugfs.  Instrumentation code is behind the
HCALL_STATS config option and has no impact if not enabled.
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Base patch for PA6T and PA6T-1682M. This introduces the
arch/powerpc/platform/pasemi directory, together with basic
implementations for various setup.

Much of this was based on other platform code, i.e. Maple, etc.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Introduce PWRficient PA6T cputable entries and feature bits.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Reduce default cacheline size on 64-bit powerpc from 128 bytes to 64.
This is the architected minimum. In most cases we'll still end up using
cache line information from the device tree, but defaults are used during
early boot and doing a few dcbst/icbi's too many there won't do any harm.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

In an attempt to make it easier for a power5 optimized app to run on a
power4 or a 970 or random earlier machine, this provides emulation of
the popcntb instruction.
Signed-off-by: NWill Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

As part of the new irq code pseries_kexec_cpu_down() was split into a
xics and mpic version. The vpa unregister logic is now only done in the
xics routine, and although that's ok in practice (we don't have SPLPAR
machines with mpic), I'd rather have the two concepts stay separate.

So move the vpa unregister into pseries_kexec_cpu_down(), which gets called
by both the xics and mpic routines. This also gives us an obvious place to
put any new kexec-down logic needed in future.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Call chip->eoi(irq) to clear any pending interrupt in case of kdump
shutdown sequence.  chip->end(irq) does not serve this purpose.
Signed-off-by: NMohan Kumar M <mohan@in.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Ben speaks; we follow.
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Take default arch/*/kernel/audit.c to lib/, have those with special
needs (== biarch) define AUDIT_ARCH in their Kconfig.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

add support for AUDIT_PERM predicate
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

New sparse caught that typo which could have caused erratic hardware
behaviour on some machines if the platform functions are used by the
firmware to change bits in some FCR registers.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The port to genirq & the new powerpc interrupt model in 2.6.18 introduced a
bug in the legacy PowerMac PIC code (used on older machines) because of a
typo potentially causing hangs due to interrupt storms.  This fixes it,
along with a performance issue causing us to do spurrious retriggers after
masking an interrupt.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes a hang on ppc32.

The problem was that I was comparing a 32-bit quantity with a 64-bit
quantity, and consequently time wasn't advancing.  This makes us use a
64-bit quantity on all platforms, which ends up simplifying the code
since we can now get rid of the tb_last_stamp variable (which actually
fixes another bug that Ben H and I noticed while going carefully through
the code).

This works fine on my G4 tibook.  Let me know how it goes on your
machines.
Acked-by: NOlaf Hering <olaf@aepfle.de>
Acked-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>