Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
提交 4c86cd9c 编写于 作者: A Andy Fleming 提交者： Paul Mackerras
浏览文件
操作

[POWERPC] Fix interrupts on 8540 ADS board 

* Fixed 8540 ADS support for the new irq layer
* Fixed 8540 ADS support for mapping PCI interrupts
* Updated 8540 ADS to use device tree for interrupt assignment
  and sense values
Signed-off-by: NPaul Mackerras <paulus@samba.org>
上级 9e8a9bc2
隐藏空白更改
内联 并排
Showing with 55 addition and 107 deletion
arch/powerpc/platforms/85xx/mpc85xx_ads.c
浏览文件 @ 4c86cd9c
......@@ -37,79 +37,7 @@ unsigned long isa_io_base = 0;
unsigned long isa_mem_base = 0;
#endif
/*
* Internal interrupts are all Level Sensitive, and Positive Polarity
*
* Note: Likely, this table and the following function should be
* obtained and derived from the OF Device Tree.
*/
static u_char mpc85xx_ads_openpic_initsenses[] __initdata = {
MPC85XX_INTERNAL_IRQ_SENSES,
0x0, /* External 0: */
#if defined(CONFIG_PCI)
(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* Ext 1: PCI slot 0 */
(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* Ext 2: PCI slot 1 */
(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* Ext 3: PCI slot 2 */
(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* Ext 4: PCI slot 3 */
#else
0x0, /* External 1: */
0x0, /* External 2: */
0x0, /* External 3: */
0x0, /* External 4: */
#endif
(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* External 5: PHY */
0x0, /* External 6: */
(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* External 7: PHY */
0x0, /* External 8: */
0x0, /* External 9: */
0x0, /* External 10: */
0x0, /* External 11: */
};
#ifdef CONFIG_PCI
/*
* interrupt routing
*/
int
mpc85xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin)
{
static char pci_irq_table[][4] =
/*
* This is little evil, but works around the fact
* that revA boards have IDSEL starting at 18
* and others boards (older) start at 12
*
* PCI IDSEL/INTPIN->INTLINE
* A B C D
*/
{
{PIRQA, PIRQB, PIRQC, PIRQD}, /* IDSEL 2 */
{PIRQD, PIRQA, PIRQB, PIRQC},
{PIRQC, PIRQD, PIRQA, PIRQB},
{PIRQB, PIRQC, PIRQD, PIRQA}, /* IDSEL 5 */
{0, 0, 0, 0}, /* -- */
{0, 0, 0, 0}, /* -- */
{0, 0, 0, 0}, /* -- */
{0, 0, 0, 0}, /* -- */
{0, 0, 0, 0}, /* -- */
{0, 0, 0, 0}, /* -- */
{PIRQA, PIRQB, PIRQC, PIRQD}, /* IDSEL 12 */
{PIRQD, PIRQA, PIRQB, PIRQC},
{PIRQC, PIRQD, PIRQA, PIRQB},
{PIRQB, PIRQC, PIRQD, PIRQA}, /* IDSEL 15 */
{0, 0, 0, 0}, /* -- */
{0, 0, 0, 0}, /* -- */
{PIRQA, PIRQB, PIRQC, PIRQD}, /* IDSEL 18 */
{PIRQD, PIRQA, PIRQB, PIRQC},
{PIRQC, PIRQD, PIRQA, PIRQB},
{PIRQB, PIRQC, PIRQD, PIRQA}, /* IDSEL 21 */
};
const long min_idsel = 2, max_idsel = 21, irqs_per_slot = 4;
return PCI_IRQ_TABLE_LOOKUP;
}
int
mpc85xx_exclude_device(u_char bus, u_char devfn)
{
......@@ -119,44 +47,63 @@ mpc85xx_exclude_device(u_char bus, u_char devfn)
return PCIBIOS_SUCCESSFUL;
}
void __init
mpc85xx_pcibios_fixup(void)
{
struct pci_dev *dev = NULL;
for_each_pci_dev(dev)
pci_read_irq_line(dev);
}
#endif /* CONFIG_PCI */
void __init mpc85xx_ads_pic_init(void)
{
struct mpic *mpic1;
phys_addr_t OpenPIC_PAddr;
/* Determine the Physical Address of the OpenPIC regs */
OpenPIC_PAddr = get_immrbase() + MPC85xx_OPENPIC_OFFSET;
mpic1 = mpic_alloc(OpenPIC_PAddr,
MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN,
4, MPC85xx_OPENPIC_IRQ_OFFSET, 0, 250,
mpc85xx_ads_openpic_initsenses,
sizeof(mpc85xx_ads_openpic_initsenses),
" OpenPIC ");
BUG_ON(mpic1 == NULL);
mpic_assign_isu(mpic1, 0, OpenPIC_PAddr + 0x10200);
mpic_assign_isu(mpic1, 1, OpenPIC_PAddr + 0x10280);
mpic_assign_isu(mpic1, 2, OpenPIC_PAddr + 0x10300);
mpic_assign_isu(mpic1, 3, OpenPIC_PAddr + 0x10380);
mpic_assign_isu(mpic1, 4, OpenPIC_PAddr + 0x10400);
mpic_assign_isu(mpic1, 5, OpenPIC_PAddr + 0x10480);
mpic_assign_isu(mpic1, 6, OpenPIC_PAddr + 0x10500);
mpic_assign_isu(mpic1, 7, OpenPIC_PAddr + 0x10580);
/* dummy mappings to get to 48 */
mpic_assign_isu(mpic1, 8, OpenPIC_PAddr + 0x10600);
mpic_assign_isu(mpic1, 9, OpenPIC_PAddr + 0x10680);
mpic_assign_isu(mpic1, 10, OpenPIC_PAddr + 0x10700);
mpic_assign_isu(mpic1, 11, OpenPIC_PAddr + 0x10780);
/* External ints */
mpic_assign_isu(mpic1, 12, OpenPIC_PAddr + 0x10000);
mpic_assign_isu(mpic1, 13, OpenPIC_PAddr + 0x10080);
mpic_assign_isu(mpic1, 14, OpenPIC_PAddr + 0x10100);
mpic_init(mpic1);
struct mpic *mpic;
struct resource r;
struct device_node *np = NULL;
np = of_find_node_by_type(np, "open-pic");
if (np == NULL) {
printk(KERN_ERR "Could not find open-pic node\n");
return;
}
if(of_address_to_resource(np, 0, &r)) {
printk(KERN_ERR "Could not map mpic register space\n");
of_node_put(np);
return;
}
mpic = mpic_alloc(np, r.start,
MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN,
4, 0, " OpenPIC ");
BUG_ON(mpic == NULL);
of_node_put(np);
mpic_assign_isu(mpic, 0, r.start + 0x10200);
mpic_assign_isu(mpic, 1, r.start + 0x10280);
mpic_assign_isu(mpic, 2, r.start + 0x10300);
mpic_assign_isu(mpic, 3, r.start + 0x10380);
mpic_assign_isu(mpic, 4, r.start + 0x10400);
mpic_assign_isu(mpic, 5, r.start + 0x10480);
mpic_assign_isu(mpic, 6, r.start + 0x10500);
mpic_assign_isu(mpic, 7, r.start + 0x10580);
/* Unused on this platform (leave room for 8548) */
mpic_assign_isu(mpic, 8, r.start + 0x10600);
mpic_assign_isu(mpic, 9, r.start + 0x10680);
mpic_assign_isu(mpic, 10, r.start + 0x10700);
mpic_assign_isu(mpic, 11, r.start + 0x10780);
/* External Interrupts */
mpic_assign_isu(mpic, 12, r.start + 0x10000);
mpic_assign_isu(mpic, 13, r.start + 0x10080);
mpic_assign_isu(mpic, 14, r.start + 0x10100);
mpic_init(mpic);
}
/*
......@@ -165,7 +112,9 @@ void __init mpc85xx_ads_pic_init(void)
static void __init mpc85xx_ads_setup_arch(void)
{
struct device_node *cpu;
#ifdef CONFIG_PCI
struct device_node *np;
#endif
if (ppc_md.progress)
ppc_md.progress("mpc85xx_ads_setup_arch()", 0);
......@@ -186,8 +135,7 @@ static void __init mpc85xx_ads_setup_arch(void)
for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
add_bridge(np);
ppc_md.pci_swizzle = common_swizzle;
ppc_md.pci_map_irq = mpc85xx_map_irq;
ppc_md.pcibios_fixup = mpc85xx_pcibios_fixup;
ppc_md.pci_exclude_device = mpc85xx_exclude_device;
#endif
......
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或