Add support for ABTS failure handling:

- Add asynchronous ABTS notification event feature to driver (CR 124578)
- Change driver message 3092 and 3116 to KERN_WARNING (CR 124768)
- Alter the SCR ELS command to use the temporary RPI and the
  Destination DID for SLI4-FC (CR 126070)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Adapter (SLI) interface fixes:

- Modify WQ handling to use entry_repost (CR 123981)
- Fix for ABTS.  Do not free original IOCB whenever ABTS fails. (CR 115829)
- Check board for FCoE before reading FCoE paramaters (CR124731)
- Add support for SLI4 FC Loop mode (CR 124721)
- Add support for resource count changes during fw reset. (CR 125888, 125675)
- Increase CQE count from 256 to 1024. (CR 126149)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Miscellaneous fixes in sysfs and mgmt interfaces:

- Added SLI4 INTF_TYPE and SLI_FAMILY as sub-field to the fwrev sysfs
  attribute (CR 124103)
- Added a sysfs attribute "protocol" to report SLI4 port link protocol
  type (CR 124102)
- Increment mix-and-match minor number by 1 for added "protocol" sysfs
  attribute. (124102)
- Move the link speed check into the generic sli3/sli4 code
  path. (CR 124185, 124122)
- Deleted check for inExtWLen (CR 122523)
- Add the word "offline" to message 2889 (CR 124385)
- Conditionalize the firmware upgrade/downgrade so that it is only
  attempted for SLI4 type 2 boards (CR 124406)
- Return an error if the mbox sysfs is called. (CR 124210)
- When port_state is less than LPFC_VPORT_READY, report
  FC_PORTSTATE_BYPASSED (CR 120018)
- Added driver support for performing persistent linkdown based on
  configure region 23 (CR 124534)
- Added restore state and error log when sysfs board_mode attribute
  access failed (CR 124158)
- Added support for SLI4_CONFIG non-embedded COMN_GET_CNTL_ADDL_ATTR
  pass-through (CR 124466)
- Rejecting un-supported multi-buffer mailbox commands (CR 124771)
- Byte swap the extended data request and response data for extended
  mailbox data (CR 125081)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The module.h header was implicitly present everywhere, so files
with no explicit include of the module infrastructure would build
anyway.  We are now removing the implicit include, and so we need
to call out the module.h file that we need explicitly.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Change driver version to 8.3.27
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added T10 DIFF error injection code.
Added T10 DIFF structure definitions for SLI4 devices.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix queue allocation failure recovery

- Move the allocation of the Queues closer to the creation of the queues.
- If there is a problem with creation, or if the HBA is reset, the queues
  will be completely freed and re allocated.
- Only allocate fcp_eq_hdl if cfg_fcp_eq_count is non-zero.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Implemented new algorithm for getting physical port name for all SLI4 devices
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Changed the timeout value for flash-based SLI_CONFIG (0x9B)
mailbox command to 300 seconds for worst case flash delays.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Miscellanous logic and interface fixes

- Fix lpfc_init_vfi_cmpl to check the interface type for interface type 0
  before parsing the results.
- Cast uint32_t values that are multiplied to uint64_t before the
  multiplication.
- Instead of "break" statement when PCI read returned error, use the goto
  statement to the end of the routine after setting return value
- moved the msleep(10) to the beginning of the wait loop for checking the
  SLIPort_Status register
- Added the code to follow the existing wait for SLIPort_Status register RDY,
  ERR, and RN bits to be set by the port before proceeding to perform PCI
  function reset.
- Do not override ulpCt_h and ulpCt_l for SLI 4 ports.
- For vport delete, call lpfc_nlp_put when the vport's vpi state is not
  marked with VPI_REGISTERED.
- Added missed fields into the driver's Controller Attributes Structure
- Changed ringing EQ/CQ/RQ doorbell register to be dependent on the size
  of the queue.
- Return -EACCES in issue_reset if cfg_enable_hba_reset is zero.
- Added new logging flag LOG_FCP_UNDER 0x00040000 to qualify underrun logging.
- Add a check in the fabric name display routine to display 0 if the port
  state is <= FLOGI.
- Add a check to the switch statement in lpfc_decode_firmware_rev to check
  for an 'X'.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix SYSFS interface issues.

- In the lpfc_sli4_pdev_status_reg_wait() routine, after initial 100ms delay
  following write to PHYSDEV_CONTROL register for the firmware reaction, check
  the RN bit and ERR bit of the SLIPORT_STATUS register. If none of them
  became 1, the previous PHYSDEV_CONTROL register should be considered failed
  due to lack of privilege and error for no permission should be returned
  immediately without getting into the wait for RDY bits on the SLIPORT_STATUS
  register.
- Remove the driver check on dev->is_physfn before proceed to perform the
  PHYSDEV_CONTROL register write, and let the PCI function's privilege
  setting and driver handling of PHYSDEV_CONTROL register write failure to
  handle the reset-ability through the SLI port.
- Added key to ctlreg_write to prevent unauthorized or unexpected write to
  the control register.
- Change return to EACCES for sysfs access that are failed because hba_reset
  is disabled.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix HBA initialization issues

- Swap all values that come from the firmware image on little endian systems.
  Created a new bf_get_be macro that does the same as the bf_get_le macro but
  for big endian data instead of little endian data.
- Moved the incrementing of temp_offset after the copy
  fixed the write object loop to use temp_offset to figure out where the end
  of the image is instead of offset.
- Added the necessary codes for properly bringing the driver instance offline
  and then trying to bring the port back online with the PCI function IP reset.
  If it fails to bring the SLI port back online, it will fall through to
  bringing the SLI port to HBA error offline.
- Add a call in the probe_one_s3 and probe_one_s4 routines to get the Modeldesc
- Change OCe50100 to OCe15100
- Made the error log also include the PCI BAR bitmap returned from kernel call
  pci_select_bars().
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix issues pertaining to SCSI/FC protocol.

- Allow frames destined to 0xFFFFFE to be processed by the driver by matching
  that DID with the physical port.
- Call lpfc_sli_issue_iocb with context1 set to ndlp
- In echo command accept function, adjust memcpy to limit memcpy to 1K
- Set LPFC_SLI3_BG_ENABLED properly upon completion.
- Skip the INIT_VFI call in lpfc_register_fcf if the FCF is already
  registered and go immediately to initial flogi.
- use "status" variable instead of "ret" variable to hold the return of the
  fc_block_scsi_eh.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Change driver version to 8.3.25
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch implements a new FCF failover policy for the lpfc driver. It
allows the driver to choose which FCF to failover to based on the FCF
priority. This patch also introduces a new sysfs parameter
(fcf_failover_policy) to allow the user to choose which FCF failover policy
to use.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Enhancements to Debug infrastructure

- debugfs additions for new hardware.
- Correct stack overflow in lpfc_debugfs_dumpHBASlim_data()
- Correct warning on uninitialized reg_val in lpfc_idiag_drbacc_write()
- Separated the iDiag command for capturing mailbox commands for generic
  issue mailbox command entry point and for BSG multi-buffer handling.
- Added capturing dumping capabiliy of mailbox command and external buffer
  for the completion of the mailbox command so that the outcome can be
  examined.
- Changed all the iDiag command structure data array indexing introduced so
  far with properly defined macros.
- Added SLI4 device PCI BAR memory mapped register read/browse, write-by-
  value, set-bit, and clear-bit methods for both interface type 0 and
  interface type 2.
- Corrected warnings on mbxstatus being uninitialized in error paths in
  lpfc_bsg.c
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

PCI and SR-IOV Fixes

- Call pci_save_state after the pci_restore_state completes.
- After calling pci_enable_pcie_error_reporting() and checking the return
  value for logging messages from rc, reset rc to 0 to it will not later be
  interpreted for error.
- Read PCI config space SR-IOV capability to get the number of VFs supported.
- Check for the PF's supported number of VFs before invoking PCI enable sriov
  API call and log error message that user requested number of VFs is beyond
  the PF capability if such request is passed in.
- Added check for Physical function with Virtual Functions attached. If so,
  first disable all the VFs before proceeding to device reset.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fabric and Target Discovery Fixes

- Clear FC_VPORT_NEEDS_INIT_VPI flag during completion of REG_VFI mailbox
  command.
- Prevent SLI3 Code from unregistering the physical VPI.
- Add an else clause to the code that checks and sets
  sp->cmn.request_multiple_Nport to clear the bit.
- Remove a redundant mbox free.
- Modified lpfc_sli4_async_fip_evt to pass in physical VPI toi
  lpfc_find_vport_by_vpid function.
- Modified lpfc_find_vport_by_vpid to translate physical VPI to logical VPI
  before comparing with vport VPI.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Adapter Interface fixes and changes

- Modify the macro field from lpfc_init_vpi_vpi to lpfc_init_vfi_vpi
- Add the new CQE_CODE_RECEIVE_V1 CQE Code, add code in the driver to handle
  the new Code the same as the CQE_CODE_RECEIVE code except that there are
  two new checks for this code that will cause the driver to use the new V1
  macros for rq_id and fcf_id.
- Fix a bug in lpfc_prep_seq() where the size out of the first CQE was
  ONLY being used, even though multiple dmabufs make up the sequence,
  each have their own CQE with potentially different sizes.
- Fix bug in lpfc_bsg_ct_unsol_event() where the ulpContext and ulpWord[3]
  fields of the XMIT_SEQUENCE64_CX IOCB were being calculated incorrectly.
- Do physical to logical translation before indexing into the active
  XRI array.
- Populate physical vpi in the iocb data structure.
- Put the current accumulated total in each IOCB in the chain as we are
  walking thru then. The last IOCB in the chain should have the total
  length of the sequence.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Miscellaneous Bug fixes and code cleanup

- Fix 16G link speed reporting by adding check for 16G check.
- Change the check and enforcement of MAILBOX_EXT_SIZE (2048B)
  to the check and enforcement of BSG_MBOX_SIZE - sizeof(MAILBOX_t) (3840B).
- Instead of waiting for a fixed amount of time after performing firmware
  reset, the driver shall wait for the Lancer SLIPORT_STATUS register for the
  readiness of the firmware for bring up.
- Add logging to indicate when dynamic parameters are changed.
- Add revision and date to the firmware image format.
- Use revision instead of rev_name to check firmware image version.
- Update temporary offset after memcopy is complete for firmware update.
- Consolidated the use of the macros to get rid of duplicated register
  offset definitions.
- Removed the unused second parameter in routine lpfc_bsg_diag_mode_enter()
- Enable debugfs when debugfs is enabled.
- Update function comments for lpfc_sli4_alloc_xri and lpfc_sli4_init_rpi_hdrs.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

T10 DIF Fixes

- Fix the case where the SCSI Host supplies the CRC and driver to controller
  protection is on.
- Only support T10 DIF type 1. LBA always goes in ref tag and app tag is not
  checked.
- Change the format of the sense data passed up to the SCSI layer to match the
  Descriptor Format Sense Data found in SPC-4 sections 4.5.2.1 and 4.5.2.2.
- Fix Slip PDE implementation.
- Remove BUG() in else casein lpfc_sc_to_bg_opcodes.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

All these are instances of
  #define NAME value;
or
  #define NAME(params_opt) value;

These of course fail to build when used in contexts like
  if(foo $OP NAME)
  while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
  foo = NAME + 1;    /* foo = value; + 1; */
  bar = NAME - 1;    /* bar = value; - 1; */
  baz = NAME & quux; /* baz = value; & quux; */

Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.

There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: NPhil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:

In file included from arch/x86/include/asm/uaccess.h:573,
                 from include/linux/uaccess.h:5,
                 from include/linux/highmem.h:7,
                 from include/linux/pagemap.h:10,
                 from include/linux/blkdev.h:12,
                 from drivers/scsi/lpfc/lpfc_debugfs.c:21:
In function 'copy_from_user':
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct

presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Extend BSG infrastructure and add link diagnostics:
- Removed unnecessary copies in handling pass-through mbox cmds.
- Add embedded SLI_CONFIG support for BSG.
- Add multibuffer support.
- Implemented the setting up and tearing down Lancer FC device for performing
  internal and external loopback diagnostic tests.
- Implemented the driver support for performing new link diagnostic tests
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.

[jejb: checkpatch.pl fixes]
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

Add request-firmware support:
- Add support for request_firmware interface for INTF2 SLI4 ports.
- Add ability to reset SLI4 INTF2 ports.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

Extended hardware support and support dump images:
- Make the size to be MAILBOX_SYSFS_MAX (4096) so that it allows the maximum
  sysfs binary access interface possible.
- Add ids and model names for new hardware
- Add capability of inducing SLI4 firmware dump obj file
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
  is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
  then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
  PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
  instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
  reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
  with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
  unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

- kenrel -> kernel
- whetehr -> whether
- ttt -> tt
- sss -> ss
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Update driver version to 8.3.22
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Fixed the mixed declarations and codes which violate ISO C90
   (declarations in subsections that assign at declaration)
- Add BSG data transfer size protection in mailbox command pass-through path
- Invoke BSG job_done while holding spinlock to fix deadlock
- Added support for checking SLI_CONFIG subcommands
- Fixed bug in BSG mailbox size check to non-embedded external buffer
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fixes related to new hardware

- Restrict driver to look at BAR2 or BAR4 only for if_type 0.
- Allow SLI4 with FCOE_MODE not set for new SLI4 FC adapters.
- Add Temporary RPI field to the ELS request WQE.
- Do not override CT field in issue_els_flogi for SLI4 IF type 2
- For RQ_CREATE_V2 mbx cmd: fill in the rqe_size and page_size for RQ_CREATE.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Miscellaneous fixes

- Do not limit RPI Count to a minimum of 64
- Fix FCFI incorrect on received unsolicited frames.
- Save the FCFI returned in the REG_FCFI mailbox command if it was successful.
- Fixed Vports not sending FDISC after lips.
- Align based on the SLI4_PAGE_SIZE.
- Fixed double byte swap on received RRQ.
- Fixed mask size for the wq_id mask from 0x7F to 0x7FFF.
- Clear FC_FABRIC flag when NPIV LOGO completes (and add a log message).
- Modified driver to skip round robin only when ulpStatus==LOCAL_REJECT
  and word4=SEQUENCE_TIMEOUT to prevent FLOGI to disconnected FCF.
- Don't add rport if driver unloading
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Debugfs enhancements

- Added iDiag support for new adapters.
- Added queue entry access methods.
- Fix host/port index in decimal
- Added Doorbell register access methods.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Stop using cmd->serial_number in printks.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>