Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 18 12月, 2015 2 次提交
    • K
      Input: goodix - add axis swapping and axis inversion support · ad48cf5e
      由 Karsten Merker 提交于 
      Implement support for the following device-tree and ACPI 5.1 DSD
properties in the goodix touchscreen driver:

 - touchscreen-inverted-x:  X axis is inverted (boolean)
 - touchscreen-inverted-y:  Y axis is inverted (boolean)
 - touchscreen-swapped-x-y: X and Y axis are swapped (boolean)

These are necessary on tablets which have a display in portrait
format while the touchscreen is in landscape format, such as e.g.
the MSI Primo 81.
Signed-off-by: NKarsten Merker <merker@debian.org>
Tested-by: NBastien Nocera <hadess@hadess.net>
Tested-by: Irina Tirdea <irina.tirdea@intel.com> (with ACPI DSD properties)
Tested-by: Aleksei Mamlin <mamlinav@gmail.com> (with device-tree properties)
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
      ad48cf5e
    • I
      Input: goodix - reset device at init · ec6e1b40
      由 Irina Tirdea 提交于 
      After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.

This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).

For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI/device tree). For devices
that do not have the gpio pins properly declared, the functionality
depending on these pins will not be available, but the device can still
be used with basic functionality.

For both device tree and ACPI, the interrupt gpio pin configuration is
read from the "irq-gpios" property and the reset pin configuration is
read from the "reset-gpios" property. For ACPI 5.1, named properties
can be specified using the _DSD section. This functionality will not be
available for devices that use indexed gpio pins declared in the _CRS
section (we need to provide backward compatibility with devices
that do not support using the interrupt gpio pin as output).

For ACPI, the pins can be specified using ACPI 5.1:
Device (STAC)
{
    Name (_HID, "GDIX1001")
    ...

    Method (_CRS, 0, Serialized)
    {
        Name (RBUF, ResourceTemplate ()
        {
            I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
                AddressingMode7Bit, "\\I2C0",
                0x00, ResourceConsumer, ,
                )

            GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
                "\\I2C0", 0x00, ResourceConsumer, ,
                 )
                 {   // Pin list
                     0
                 }

            GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
                IoRestrictionOutputOnly, "\\I2C0", 0x00,
                ResourceConsumer, ,
                )
                {
                     1
                }
        })
        Return (RBUF)
    }

    Name (_DSD,  Package ()
    {
        ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
        Package ()
        {
            Package (2) {"irq-gpios", Package() {^STAC, 0, 0, 0 }},
            Package (2) {"reset-gpios", Package() {^STAC, 1, 0, 0 }},
            ...
        }
    }
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Signed-off-by: NIrina Tirdea <irina.tirdea@intel.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NBastien Nocera <hadess@hadess.net>
Tested-by: NBastien Nocera <hadess@hadess.net>
Tested-by: NAleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
      ec6e1b40
  3. 04 11月, 2015 1 次提交
  5. 31 10月, 2015 1 次提交
  7. 22 10月, 2015 1 次提交
  9. 17 10月, 2015 2 次提交
  11. 15 10月, 2015 1 次提交
  13. 14 10月, 2015 1 次提交
  15. 03 10月, 2015 1 次提交
  17. 30 9月, 2015 1 次提交
    • S
      Input: add DA9062 OnKey capability to DA9063 OnKey driver · a27b5e0a
      由 S Twiss 提交于 
      Add DA9062 OnKey support into the existing DA9063 OnKey driver component by
using generic access tables for common register and bit mask definitions.

The following change will add generic register and bit mask support to the
DA9063 OnKey.

The following alterations have been made to the DA9063 OnKey:

- Addition of a da906x_chip_config structure to hold all
  generic registers and bitmasks for this type of OnKey component.
- Addition of an struct of_device_id table for DA9063 and DA9062
  defaults
- Refactoring functions to use struct da9063_onkey accesses to generic
  registers/masks instead of using defines from registers.h
- Re-work of da9063_onkey_probe() to use of_match_node() and
  dev_get_regmap() to provide initialisation of generic registers and
  masks and access to regmap
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
      a27b5e0a
  19. 28 9月, 2015 2 次提交
  21. 20 9月, 2015 1 次提交
  23. 06 9月, 2015 2 次提交
  25. 17 8月, 2015 1 次提交
  27. 08 8月, 2015 1 次提交
  29. 04 8月, 2015 1 次提交
    • D
      Input: zforce - make the interrupt GPIO optional · 62f46669
      由 Dirk Behme 提交于 
      Add support for hardware which uses an I2C Serializer / Deserializer
(SerDes) to communicate with the zFroce touch driver. In this case the
SerDes will be configured as an interrupt controller and the zForce driver
will have no access to poll the GPIO line.

To support this, we add two dedicated new GPIOs in the device tree:
reset-gpios and irq-gpios, with the irq-gpios being optional.

To not break the existing device trees, the index based 'gpios' entries
are still supported, but marked as deprecated.

With this, if the interrupt GPIO is available, either via the old or new
device tree style, the while loop will read and handle the packets as long
as the GPIO indicates that the interrupt is asserted (existing, unchanged
driver behavior).

If the interrupt GPIO isn't available, i.e. not configured via the new
device tree style, we are falling back to one read per ISR invocation
(new behavior to support the SerDes).

Note that the gpiod functions help to handle the optional GPIO:
devm_gpiod_get_index_optional() will return NULL in case the interrupt
GPIO isn't available. And gpiod_get_value_cansleep() does cover this, too,
by returning 0 in this case.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: NHeiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
      62f46669
  31. 31 7月, 2015 1 次提交
  33. 24 7月, 2015 5 次提交
  35. 15 7月, 2015 1 次提交
  37. 12 7月, 2015 1 次提交
  39. 30 5月, 2015 1 次提交
  41. 14 5月, 2015 1 次提交
  43. 09 5月, 2015 1 次提交
  45. 25 3月, 2015 2 次提交
  47. 24 3月, 2015 2 次提交
  49. 21 3月, 2015 1 次提交
  51. 09 3月, 2015 1 次提交
    • H
      Input: sun4i-ts - A10 (sun4i) has a different temperature curve · 91c68a7c
      由 Hans de Goede 提交于 
      Testing has revealed that the temperature in the rtp controller of the A10
(sun4i) SoC has a different curve then on the A13 (sun5i) and later models.

Add a new sun5i-a13-ts compatible to differentiate the newer models and
set the curve based on the compatible string.

The new curve is still not ideal on all A10-s, that seems to have to
do with there being a large spread between different A10-s out there,
the new curve us based on callibration results on 4 completely different
models:
                        raw min raw max temp min temp max stepsize offset
Tong Zhang's hackberry    2402    2680    45.0     80.0    0.125   -255.3
Hansg's Cubieboard        2207    2300    36.0     45.0    0.096   -175.8
Olliver's lime 1 (*):     2258    2537    48.3     87.1    0.139   -265.7
Olliver's lime 2 (*):     2222    2486    46.7     91.7    0.170   -331.0
*) from: http://linux-sunxi.org/Temperature_Calibration

Average all 4:                                             0.133   -257.0
Average without outliers (middle 2):                       0.132   -261.0

Since it is better to slightly overreport the temperature this patch uses
the average of all 4 as curve.

This fixes the temperature reported on the A10 being much higher then
expected.
Reported-by: NTong Zhang <lovewilliam@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
      91c68a7c
  53. 07 3月, 2015 2 次提交
  55. 03 3月, 2015 1 次提交
  57. 04 2月, 2015 1 次提交