[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.

[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.

[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: NJosip Pavic <Josip.Pavic@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Freesync borderless is not meant to be enabled on any APUs

[HOW]
Add is_apu cap to dcn21_resource_construct for correct recognition
Signed-off-by: NMichael Strauss <michael.strauss@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
SMU FW previously had an issue with lowering display clock to below 100
MHz, and a workaround was put in to limit it.  Newest SMU FW does not
have this issue, and no longer needs the 100MHz cap.

[HOW]
Remove the 100MHz cap based on the SMU FW version.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line.  In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM).  It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine.  However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.

[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: NWenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: NNikola Cornij <Nikola.Cornij@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
When test pattern is enabled with ODM combine, test pattern is generated
by piecing multiple DPGs image together.  The current code will program
all DPGs with horizontal offset of 0. This will cause all DPGs to output
the beginning of the pattern. Instead each DPG should program a
horizontal offset of its x position to form a continous pattern when
pieced together.
Signed-off-by: NWenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: NNikola Cornij <Nikola.Cornij@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[how]
Allow vsc info packet if vsc is supported.  Update vsc based on test
pattern request.  Remove dpg_is_blanked polling, apply hardware global
lock instead to ensure double buffered dpg is updated with vsc in one
frame
Signed-off-by: NWenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY & HOW]
In order to correctly intepret clock table, num_states is also needed.
This field did not get moved with clock_table but should next to it for
easier access/viewing.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp

[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: NJoseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.

[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: NWenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: NAshley Thomas <Ashley.Thomas2@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.

[How]
Move psr_on_dmub flag from dc_debug_options to dc_config.
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Previously implemented early_cr_pattern we mistook dp_hw_link_settings
for a redundant call of dpcd_set_link_settings

[How]
revert the changes to dpcd_set_link_settings calls for this workaround.
Do not need to revert the entire change since it only affects patched
case
Signed-off-by: NMartin Leung <martin.leung@amd.com>
Reviewed-by: NDavid Galiffi <David.Galiffi@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Removes codestyle issues on detect_dp function as suggested by
checkpatch.pl.

CHECK: Lines should not end with a '('
WARNING: Missing a blank line after declarations
WARNING: line over 80 characters
CHECK: Alignment should match open parenthesis
Signed-off-by: NMelissa Wen <melissa.srw@gmail.com>
Reviewed-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: NZhan Liu <zhan.liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Coding style clean up on enable_link_dp function as suggested by
checkpatch.pl:

CHECK: Lines should not end with a '('
WARNING: line over 80 characters
WARNING: suspect code indent for conditional statements (8, 24)
CHECK: braces {} should be used on all arms of this statement
ERROR: else should follow close brace '}'
CHECK: Comparison to NULL could be written
       "link->preferred_training_settings.fec_enable"
Signed-off-by: NMelissa Wen <melissa.srw@gmail.com>
Reviewed-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This is freeing the wrong variable so it will crash.  It should be
freeing "*dmub" instead of "dmub".

Fixes: 4c1a1335 ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

There are multiple statements that are indented incorrectly. Add
in the missing tabs.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:
 In function hubp21_set_vm_system_aperture_settings:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:343:23:
 warning: variable mc_vm_apt_default set but not used [-Wunused-but-set-variable]

It is never used, so remove it.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
when changing display clock, SMU need to use power up DFS and use
DENTIST to ramp DFS DID to switch target frequency before switching back
to bypass.

[How]
fixed the minimum display clock to 100MHz, it's W/A the same with PCO.
Signed-off-by: NYu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
System will crash when trying to access local sink in
core_link_enable_stream in MST case.

[How]
Access patches directly from stream.
Signed-off-by: NJaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Reviewed-by: NAshley Thomas <Ashley.Thomas2@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Underflow sometimes occurs during transition into MPO with stutter
enabled.

[How]
When transitioning into MPO, disable stutter. Re-enable stutter within
one frame.
Signed-off-by: NGeorge Shen <george.shen@amd.com>
Signed-off-by: NTony Cheng <tony.cheng@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Currently clock table struct is very far down in the bounding box struct
making it hard to find while debugging, especially when using the
dal3dbgext.

[HOW]
Move it up so it is the first struct defined, and therefore much easier
to find and access.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
In some display configuration like 1080P monitor playing a 1080P video,
if user use ALT+F4 to exit Movie and TV, there is a chance clocks are
same only water mark changed. Current clock optimization machanism will
result in water mark keeps high after exit Movie and TV app.

[How]
Return if watermark need to be optimized when doing program watermark,
perform the optimization after.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Need to assign surface size rather than viewport size for surface size
dml variable.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NEric Bernstein <Eric.Bernstein@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We need to update TTU properly if DRAMClockChangeWatermark changes. If
TTU < DRAMClockChangeWatermark, we pstate won't be allowed and we will
hang in some PSR cases.

[How]
Update TTU if DramClockChangeWatermark value increases (only if TTU was
dependent on the watermark value on the DRAMClockChangeWatermark value
in the first place).
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
RV2 and variants are indistinguishable by hw internal rev alone, need to
be distinguishable in order to correctly set max vlevel.  Previous
detection change incorrectly checked for hw internal rev.

[HOW]
Use pci revision to check if RV2 or low power variant Correct a few
overlapping ASICREV range checks
Signed-off-by: NMichael Strauss <michael.strauss@amd.com>
Reviewed-by: NMichael Strauss <Michael.Strauss@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.

[How]
Add infrastructure to enable and disable PSR on DMCUB.
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NEric Bernstein <Eric.Bernstein@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Update dcn20_populate_dml_pipes_from_context to correctly handle odm
when no surface is provided.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
DalMPVisualConfirm does not support FreeSync 2 ARGB2101010 which causes
black visual confirm bar when playing HDR video on FreeSync 2 display in
full screen mode

[How]
Added pink color for DalMPVisualConfirm on FreeSync 2 ARGB2101010
surface
Signed-off-by: NPeikang Zhang <peikang.zhang@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Previously implemented early_cr_pattern was link level but the whole
asic should be affected.

[How]
 - change old link flag to dc level
 - new bit in dc->work_arounds set by DM
Signed-off-by: NMartin Leung <martin.leung@amd.com>
Reviewed-by: NJoshua Aberback <Joshua.Aberback@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Some displays clear ignore MSA bit on mode change, which cause
blackscreen when programming variable vtotals. Ignore MSA bit needs
programming needs to be delayed or re-set to be retained.

[How]
Create patch to delay programming ignore MSA bit after unblanking
stream.
Signed-off-by: NJaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
A software workaround is required for all vendor-built cards on platform.

[How]
When performing DP link training, we must send TPS1 before DPCD:100h is
written with the proper bit rate value. This change must be applies in
ALL cases when LT happens.
Signed-off-by: NDavid Galiffi <David.Galiffi@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Not programming dto with same values causes test failures in DCN2 diags
DPP tests.

[HOW]
This reverts commit 1b53e733.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Currently DAL programs negative slope for the last point of output
transfer function curve.

[How]
Applying a check for the last PWL point for RGB values not to be
smaller than previous. If smaller, initialize the last point values
to a sum of previous PWL value and previous PWL delta;
Signed-off-by: NVladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
There are some structures and functions meant only to be used in the
scope of that single rn_clk_mgr c file.

[How]
Make structs and funcs static if only meant to be used within
rn_clk_mgr
Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Make panel backlight and power on/off functions into
hardware specific function pointers

[How]
Add function pointers for panel related hw functions
 - is_panel_powered_on
 - is_panel_backlight_on
Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Add optimization to allow pstate change support when all displays
are off in DCN2.

[How]
Add clk_mgr_helper_get_active_plane_cnt() to sum plane_count for all
valid stream_status[].  If plane_count is 0, then there are no active
or virtual streams present. Use plane_count == 0 as extra condition to
enable p_state_change_support in dcn2_update_clocks().
Signed-off-by: NSamson Tam <Samson.Tam@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
According to HW team, PG is dropped for NV12, but programming
the registers will still cause power to be consumed, so don't
program for NV12.

[How]
Set function pointer to NULL if NV12
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>